/* pinmux_board_quark_se_dev.c - Quark SE Development Board pinmux driver */

/*
 * Copyright (c) 2016 Intel Corporation
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <kernel.h>
#include <soc.h>
#include <device.h>
#include <init.h>
#include <pinmux.h>
#include <sys_io.h>
#include "pinmux/pinmux.h"

#include <pinmux_quark_mcu.h>

/*
 * This is the full pinmap that we have available on the board for configuration
 * including the ball position and the various modes that can be set.  In the
 * pinmux_defaults we do not spend any time setting values that are using mode
 * A as the hardware brings up all devices by default in mode A.
 */

/* pin, ball, mode A, mode B, mode C */
/* 0  F02, gpio_0, ain_0, spi_s_cs */
/* 1  G04, gpio_1, ain_1, spi_s_miso */
/* 2  H05, gpio_2, ain_2, spi_s_sck */
/* 3  J06, gpio_3, ain_3, spi_s_mosi */
/* 4  K06, gpio_4, ain_4, NA */			/* 15.4 GPIO */
/* 5  L06, gpio_5, ain_5, NA */			/* 15.4 GPIO */
/* 6  H04, gpio_6, ain_6, NA */			/* 15.4 GPIO */
/* 7  G03, gpio_7, ain_7, NA */
/* 8  L05, gpio_ss_0, ain_8, uart1_cts */	/* UART debug */
/* 9  M05, gpio_ss_1, ain_9, uart1_rts */	/* UART debug */
/* 10 K05, gpio_ss_2, ain_10 */
/* 11 G01, gpio_ss_3, ain_11 */
/* 12 J04, gpio_ss_4, ain_12 */
/* 13 G02, gpio_ss_5, ain_13 */
/* 14 F01, gpio_ss_6, ain_14 */
/* 15 J05, gpio_ss_7, ain_15 */
/* 16 L04, gpio_ss_8, ain_16, uart1_txd */	/* UART debug */
/* 17 M04, gpio_ss_9, ain_17, uart1_rxd */	/* UART debug */
/* 18 K04, uart0_rx, ain_18, NA */		/* BT UART */
/* 19 B02, uart0_tx, gpio_31, NA */		/* BT UART */
/* 20 C01, i2c0_scl, NA, NA */			/* EEPROM, BT, Light Sensor */
/* 21 C02, i2c0_sda, NA, NA */			/* EEPROM, BT, Light Sensor */
/* 22 D01, i2c1_scl, NA, NA */
/* 23 D02, i2c1_sda, NA, NA */
/* 24 E01, i2c0_ss_sda, NA, NA */
/* 25 E02, i2c0_ss_scl, NA, NA */
/* 26 B03, i2c1_ss_sda, NA, NA */		/* IMU */
/* 27 A03, i2c1_ss_scl, NA, NA */		/* IMU */
/* 28 C03, spi0_ss_miso, NA, NA */		/* IMU */
/* 29 E03, spi0_ss_mosi, NA, NA */		/* IMU */
/* 30 D03, spi0_ss_sck, NA, NA */		/* IMU */
/* 31 D04, spi0_ss_cs0, NA, NA */		/* IMU */
/* 32 C04, spi0_ss_cs1, NA, NA */
/* 33 B04, spi0_ss_cs2, gpio_29, NA */		/* 15.4 GPIO */
/* 34 A04, spi0_ss_cs3, gpio_30, NA */
/* 35 B05, spi1_ss_miso, NA, NA */
/* 36 C05, spi1_ss_mosi, NA, NA */
/* 37 D05, spi1_ss_sck, NA, NA */
/* 38 E05, spi1_ss_cs0, NA, NA */
/* 39 E04, spi1_ss_cs1, NA, NA */
/* 40 A06, spi1_ss_cs2, uart0_cts, NA */	/* BT UART */
/* 41 B06, spi1_ss_cs3, uart0_rts, NA */	/* BT UART */
/* 42 C06, gpio_8, spi1_m_sck, NA */		/* 15.4 SPI */
/* 43 D06, gpio_9, spi1_m_miso, NA */		/* 15.4 SPI */
/* 44 E06, gpio_10, spi1_m_mosi, NA */		/* 15.4 SPI */
/* 45 D07, gpio_11, spi1_m_cs0, NA */		/* 15.4 SPI GPIO CS */
/* 46 C07, gpio_12, spi1_m_cs1, NA */
/* 47 B07, gpio_13, spi1_m_cs2, NA */
/* 48 A07, gpio_14, spi1_m_cs3, NA */
/* 49 B08, gpio_15, i2s_rxd, NA */
/* 50 A08, gpio_16, i2s_rscki, NA */
/* 51 B09, gpio_17, i2s_rws, NA */
/* 52 A09, gpio_18, i2s_tsck, NA */
/* 53 C09, gpio_19, i2s_twsi, NA */
/* 54 D09, gpio_20, i2s_txd, NA */
/* 55 D08, gpio_21, spi0_m_sck, NA */		/* SPI Flash */
/* 56 E07, gpio_22, spi0_m_miso, NA */		/* SPI Flash */
/* 57 E09, gpio_23, spi0_m_mosi, NA */		/* SPI Flash */
/* 58 E08, gpio_24, spi0_m_cs0, NA */		/* SPI Flash */
/* 59 A10, gpio_25, spi0_m_cs1, NA */
/* 60 B10, gpio_26, spi0_m_cs2, NA */
/* 61 C10, gpio_27, spi0_m_cs3, NA */
/* 62 D10, gpio_28, NA, NA */
/* 63 E10, gpio_ss_10, pwm_0, NA */
/* 64 D11, gpio_ss_11, pwm_1, NA */
/* 65 C11, gpio_ss_12, pwm_2, NA */
/* 66 B11, gpio_ss_13, pwm_3, NA */
/* 67 D12, gpio_ss_14, clkout_32khz, NA */
/* 68 C12, gpio_ss_15, clkout_16mhz, NA */

/*
 * On the QUARK_SE platform there are a minimum of 69 pins that can be possibly
 * set.  This would be a total of 5 registers to store the configuration as per
 * the bit description from above
 */
#define PINMUX_MAX_REGISTERS	5
static void pinmux_defaults(u32_t base)
{
	u32_t mux_config[PINMUX_MAX_REGISTERS] = { 0, 0, 0, 0, 0};
	int i = 0;

#if defined(CONFIG_SPI_2)
	PIN_CONFIG(mux_config,  0, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config,  1, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config,  2, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config,  3, PINMUX_FUNC_C);
#else
	PIN_CONFIG(mux_config,  0, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config,  1, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config,  2, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config,  3, PINMUX_FUNC_B);
#endif
	PIN_CONFIG(mux_config,  8, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config,  9, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config, 16, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config, 17, PINMUX_FUNC_C);
	PIN_CONFIG(mux_config, 33, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 40, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 41, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 42, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 43, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 44, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 55, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 56, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 57, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 58, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 63, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 64, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 65, PINMUX_FUNC_B);
	PIN_CONFIG(mux_config, 66, PINMUX_FUNC_B);

	for (i = 0; i < PINMUX_MAX_REGISTERS; i++) {
		sys_write32(mux_config[i], PINMUX_SELECT_REGISTER(base, i));
	}
}

static int pinmux_initialize(struct device *port)
{
	ARG_UNUSED(port);

	pinmux_defaults(PINMUX_BASE_ADDR);

	return 0;
}

SYS_INIT(pinmux_initialize, POST_KERNEL, CONFIG_KERNEL_INIT_PRIORITY_DEFAULT);