/*
 * Copyright (c) 2021, NXP
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include "mimxrt1160_evk-pinctrl.dtsi"

/ {
	aliases {
		led0 = &green_led;
		sw0 = &user_button;
		magn0 = &fxos8700;
		accel0 = &fxos8700;
		sdhc0 = &usdhc1;
	};

	leds {
		compatible = "gpio-leds";
		green_led: led-1 {
			gpios = <&gpio9 3 GPIO_ACTIVE_LOW>;
			label = "User LED D6";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		user_button: button-1 {
			label = "User SW7";
			gpios = <&gpio13 0 GPIO_ACTIVE_HIGH>;
		};
	};

	pwmleds {
		compatible = "pwm-leds";

		green_pwm_led: green_pwm_led {
			pwms = <&flexpwm1_pwm2 0 PWM_MSEC(20)>;
		};
	};
};

&lpuart1 {
	status = "okay";
	current-speed = <115200>;
	pinctrl-0 = <&pinmux_lpuart1>;
	pinctrl-1 = <&pinmux_lpuart1_sleep>;
	pinctrl-names = "default", "sleep";
};

&lpuart2 {
	pinctrl-0 = <&pinmux_lpuart2>;
	pinctrl-1 = <&pinmux_lpuart2_sleep>;
	pinctrl-names = "default", "sleep";
};

&user_button {
	status = "okay";
};

&green_led {
	status = "okay";
};

&lpi2c5 {
	status = "okay";
	pinctrl-0 = <&pinmux_lpi2c1>;
	pinctrl-names = "default";

	fxos8700: fxos8700@1f {
		compatible = "nxp,fxos8700";
		reg = <0x1f>;

		/* Two zero ohm resistors (R256 and R270) isolate sensor
		 * interrupt gpios from the soc and are unpopulated by default.
		 * Note that if you populate them, they conflict with camera and
		 * ethernet PHY reset signals.
		 */
		int1-gpios = <&gpio11 14 GPIO_ACTIVE_LOW>;
		int2-gpios = <&gpio11 15 GPIO_ACTIVE_LOW>;
	};
};

&flexpwm1_pwm2 {
	status = "okay";
	pinctrl-0 = <&pinmux_flexpwm1>;
	pinctrl-names = "default";
};

&enet {
	pinctrl-0 = <&pinmux_enet>;
	pinctrl-names = "default";
	ptp {
		pinctrl-0 = <&pinmux_ptp>;
		pinctrl-names = "default";
	};
};

&csi {
	pinctrl-0 = <&pinmux_csi>;
	pinctrl-names = "default";
};

&flexcan3 {
	pinctrl-0 = <&pinmux_flexcan3>;
	pinctrl-names = "default";
};

&lcdif {
	pinctrl-0 = <&pinmux_lcdif>;
	pinctrl-names = "default";
};

&lpi2c1 {
	pinctrl-0 =<&pinmux_lpi2c5>;
	pinctrl-names = "default";
};

&lpspi1 {
	pinctrl-0 = <&pinmux_lpspi1>;
	pinctrl-names = "default";
};

&lpuart2 {
	pinctrl-0 = <&pinmux_lpuart2>;
	pinctrl-1 = <&pinmux_lpuart2_sleep>;
	pinctrl-names = "default", "sleep";
};

&sai1 {
	pinctrl-0 = <&pinmux_sai1>;
	pinctrl-names = "default";
};

&lpadc0 {
	pinctrl-0 = <&pinmux_lpadc0>;
	pinctrl-names = "default";
};

&flexspi {
	pinctrl-0 = <&pinmux_flexspi1>;
	pinctrl-names = "default";
};

&usdhc1 {
	pinctrl-0 = <&pinmux_usdhc1>;
	pinctrl-1 = <&pinmux_usdhc1_dat3_nopull>;
	pinctrl-names = "default", "nopull";
};