/***************************************************************************//**
 * @file em_emu.h
 * @brief Energy management unit (EMU) peripheral API
 * @version 5.1.2
 *******************************************************************************
 * @section License
 * <b>Copyright 2016 Silicon Laboratories, Inc. http://www.silabs.com</b>
 *******************************************************************************
 *
 * Permission is granted to anyone to use this software for any purpose,
 * including commercial applications, and to alter it and redistribute it
 * freely, subject to the following restrictions:
 *
 * 1. The origin of this software must not be misrepresented; you must not
 *    claim that you wrote the original software.
 * 2. Altered source versions must be plainly marked as such, and must not be
 *    misrepresented as being the original software.
 * 3. This notice may not be removed or altered from any source distribution.
 *
 * DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Silicon Labs has no
 * obligation to support this Software. Silicon Labs is providing the
 * Software "AS IS", with no express or implied warranties of any kind,
 * including, but not limited to, any implied warranties of merchantability
 * or fitness for any particular purpose or warranties against infringement
 * of any proprietary rights of a third party.
 *
 * Silicon Labs will not be liable for any consequential, incidental, or
 * special damages, or any other relief, or for any claim by any third party,
 * arising from your use of this Software.
 *
 ******************************************************************************/

#ifndef EM_EMU_H
#define EM_EMU_H

#include "em_device.h"
#if defined( EMU_PRESENT )

#include <stdbool.h>
#include "em_bus.h"

#ifdef __cplusplus
extern "C" {
#endif

/***************************************************************************//**
 * @addtogroup emlib
 * @{
 ******************************************************************************/

/***************************************************************************//**
 * @addtogroup EMU
 * @{
 ******************************************************************************/

/*******************************************************************************
 ********************************   ENUMS   ************************************
 ******************************************************************************/

#if defined( _EMU_EM4CONF_OSC_MASK )
/** EM4 duty oscillator */
typedef enum
{
  /** Select ULFRCO as duty oscillator in EM4 */
  emuEM4Osc_ULFRCO = EMU_EM4CONF_OSC_ULFRCO,
  /** Select LFXO as duty oscillator in EM4 */
  emuEM4Osc_LFXO = EMU_EM4CONF_OSC_LFXO,
  /** Select LFRCO as duty oscillator in EM4 */
  emuEM4Osc_LFRCO = EMU_EM4CONF_OSC_LFRCO
} EMU_EM4Osc_TypeDef;
#endif

#if defined( _EMU_BUCTRL_PROBE_MASK )
/** Backup Power Voltage Probe types */
typedef enum
{
  /** Disable voltage probe */
  emuProbe_Disable = EMU_BUCTRL_PROBE_DISABLE,
  /** Connect probe to VDD_DREG */
  emuProbe_VDDDReg = EMU_BUCTRL_PROBE_VDDDREG,
  /** Connect probe to BU_IN */
  emuProbe_BUIN    = EMU_BUCTRL_PROBE_BUIN,
  /** Connect probe to BU_OUT */
  emuProbe_BUOUT   = EMU_BUCTRL_PROBE_BUOUT
} EMU_Probe_TypeDef;
#endif

#if defined( _EMU_PWRCONF_PWRRES_MASK )
/** Backup Power Domain resistor selection */
typedef enum
{
  /** Main power and backup power connected with RES0 series resistance */
  emuRes_Res0 = EMU_PWRCONF_PWRRES_RES0,
  /** Main power and backup power connected with RES1 series resistance */
  emuRes_Res1 = EMU_PWRCONF_PWRRES_RES1,
  /** Main power and backup power connected with RES2 series resistance */
  emuRes_Res2 = EMU_PWRCONF_PWRRES_RES2,
  /** Main power and backup power connected with RES3 series resistance */
  emuRes_Res3 = EMU_PWRCONF_PWRRES_RES3,
} EMU_Resistor_TypeDef;
#endif

#if defined( BU_PRESENT )
/** Backup Power Domain power connection */
typedef enum
{
  /** No connection between main and backup power */
  emuPower_None = EMU_BUINACT_PWRCON_NONE,
  /** Main power and backup power connected through diode,
      allowing current from backup to main only */
  emuPower_BUMain = EMU_BUINACT_PWRCON_BUMAIN,
  /** Main power and backup power connected through diode,
      allowing current from main to backup only */
  emuPower_MainBU = EMU_BUINACT_PWRCON_MAINBU,
  /** Main power and backup power connected without diode */
  emuPower_NoDiode = EMU_BUINACT_PWRCON_NODIODE,
} EMU_Power_TypeDef;
#endif

/** BOD threshold setting selector, active or inactive mode */
typedef enum
{
  /** Configure BOD threshold for active mode */
  emuBODMode_Active,
  /** Configure BOD threshold for inactive mode */
  emuBODMode_Inactive,
} EMU_BODMode_TypeDef;

#if defined( _EMU_EM4CTRL_EM4STATE_MASK )
/** EM4 modes */
typedef enum
{
  /** EM4 Hibernate */
  emuEM4Hibernate = EMU_EM4CTRL_EM4STATE_EM4H,
  /** EM4 Shutoff */
  emuEM4Shutoff = EMU_EM4CTRL_EM4STATE_EM4S,
} EMU_EM4State_TypeDef;
#endif


#if defined( _EMU_EM4CTRL_EM4IORETMODE_MASK )
typedef enum
{
  /** No Retention: Pads enter reset state when entering EM4 */
  emuPinRetentionDisable = EMU_EM4CTRL_EM4IORETMODE_DISABLE,
  /** Retention through EM4: Pads enter reset state when exiting EM4 */
  emuPinRetentionEm4Exit = EMU_EM4CTRL_EM4IORETMODE_EM4EXIT,
  /** Retention through EM4 and wakeup: call EMU_UnlatchPinRetention() to
      release pins from retention after EM4 wakeup */
  emuPinRetentionLatch   = EMU_EM4CTRL_EM4IORETMODE_SWUNLATCH,
} EMU_EM4PinRetention_TypeDef;
#endif

/** Power configurations. DCDC-to-DVDD is currently the only supported mode. */
typedef enum
{
  /** DCDC is connected to DVDD */
  emuPowerConfig_DcdcToDvdd,
} EMU_PowerConfig_TypeDef;


#if defined( _EMU_DCDCCTRL_MASK )
/** DCDC operating modes */
typedef enum
{
  /** DCDC regulator bypass */
  emuDcdcMode_Bypass = EMU_DCDCCTRL_DCDCMODE_BYPASS,
  /** DCDC low-noise mode */
  emuDcdcMode_LowNoise = EMU_DCDCCTRL_DCDCMODE_LOWNOISE,
#if defined(_EMU_DCDCLPEM01CFG_MASK)
  /** DCDC low-power mode */
  emuDcdcMode_LowPower = EMU_DCDCCTRL_DCDCMODE_LOWPOWER,
#endif
} EMU_DcdcMode_TypeDef;
#endif

#if defined( _EMU_DCDCCTRL_MASK )
/** DCDC conduction modes */
typedef enum
{
  /** DCDC Low-Noise Continuous Conduction Mode (CCM). EFR32 interference minimization
      features are available in this mode. */
  emuDcdcConductionMode_ContinuousLN,
  /** DCDC Low-Noise Discontinuous Conduction Mode (DCM). This mode should be used for EFM32 or
      when the EFR32 radio is not enabled. */
  emuDcdcConductionMode_DiscontinuousLN,
} EMU_DcdcConductionMode_TypeDef;
#endif

#if defined( _EMU_PWRCTRL_MASK )
/** DCDC to DVDD mode analog peripheral power supply select */
typedef enum
{
  /** Select AVDD as analog power supply. Typically lower noise, but less energy efficient. */
  emuDcdcAnaPeripheralPower_AVDD = EMU_PWRCTRL_ANASW_AVDD,
  /** Select DCDC (DVDD) as analog power supply. Typically more energy efficient, but more noise. */
  emuDcdcAnaPeripheralPower_DCDC = EMU_PWRCTRL_ANASW_DVDD
} EMU_DcdcAnaPeripheralPower_TypeDef;
#endif

#if defined( _EMU_DCDCMISCCTRL_MASK )
/** DCDC Forced CCM and reverse current limiter control. Positive values have unit mA. */
typedef int16_t EMU_DcdcLnReverseCurrentControl_TypeDef;

/** High efficiency mode. EMU_DCDCZDETCTRL_ZDETILIMSEL is "don't care". */
#define emuDcdcLnHighEfficiency       -1

/** Default reverse current for fast transient response mode (low noise).  */
#define emuDcdcLnFastTransient         160
#endif


#if defined( _EMU_DCDCCTRL_MASK )
/** DCDC Low-noise RCO band select */
typedef enum
{
  /** Set RCO to 3MHz */
  emuDcdcLnRcoBand_3MHz = 0,
  /** Set RCO to 4MHz */
  emuDcdcLnRcoBand_4MHz = 1,
  /** Set RCO to 5MHz */
  emuDcdcLnRcoBand_5MHz = 2,
  /** Set RCO to 6MHz */
  emuDcdcLnRcoBand_6MHz = 3,
  /** Set RCO to 7MHz */
  emuDcdcLnRcoBand_7MHz = 4,
  /** Set RCO to 8MHz */
  emuDcdcLnRcoBand_8MHz = 5,
  /** Set RCO to 9MHz */
  emuDcdcLnRcoBand_9MHz = 6,
  /** Set RCO to 10MHz */
  emuDcdcLnRcoBand_10MHz = 7,
} EMU_DcdcLnRcoBand_TypeDef;

/** @cond DO_NOT_INCLUDE_WITH_DOXYGEN */
/* Deprecated. */
#define EMU_DcdcLnRcoBand_3MHz          emuDcdcLnRcoBand_3MHz
#define EMU_DcdcLnRcoBand_4MHz          emuDcdcLnRcoBand_4MHz
#define EMU_DcdcLnRcoBand_5MHz          emuDcdcLnRcoBand_5MHz
#define EMU_DcdcLnRcoBand_6MHz          emuDcdcLnRcoBand_6MHz
#define EMU_DcdcLnRcoBand_7MHz          emuDcdcLnRcoBand_7MHz
#define EMU_DcdcLnRcoBand_8MHz          emuDcdcLnRcoBand_8MHz
#define EMU_DcdcLnRcoBand_9MHz          emuDcdcLnRcoBand_9MHz
#define EMU_DcdcLnRcoBand_10MHz         emuDcdcLnRcoBand_10MHz
/** @endcond */
#endif


#if defined( _EMU_DCDCCTRL_MASK )
/** DCDC Low Noise Compensator Control register. */
typedef enum
{
  /** DCDC capacitor is 1uF. */
  emuDcdcLnCompCtrl_1u0F,
  /** DCDC capacitor is 4.7uF. */
  emuDcdcLnCompCtrl_4u7F,
} EMU_DcdcLnCompCtrl_TypeDef;
#endif


#if defined( EMU_STATUS_VMONRDY )
/** VMON channels */
typedef enum
{
  emuVmonChannel_AVDD,
  emuVmonChannel_ALTAVDD,
  emuVmonChannel_DVDD,
  emuVmonChannel_IOVDD0
} EMU_VmonChannel_TypeDef;
#endif /* EMU_STATUS_VMONRDY */

#if defined( _SILICON_LABS_GECKO_INTERNAL_SDID_80 )
/** Bias mode configurations */
typedef enum
{
  emuBiasMode_1KHz,
  emuBiasMode_4KHz,
  emuBiasMode_Continuous
} EMU_BiasMode_TypeDef;
#endif

#if defined( _EMU_CMD_EM01VSCALE0_MASK )
/** Supported EM0/1 Voltage Scaling Levels */
typedef enum
{
  /** High-performance voltage level. HF clock can be set to any frequency. */
  emuVScaleEM01_HighPerformance = _EMU_STATUS_VSCALE_VSCALE2,
  /** Low-power optimized voltage level. The HF clock must be limited
      to @ref CMU_VSCALEEM01_LOWPOWER_VOLTAGE_CLOCK_MAX Hz at this voltage.
      EM0/1 voltage scaling is applied when the core clock frequency is
      changed from @ref CMU or when calling @ref EMU_EM01Init() when the HF
      clock is already below the limit. */
  emuVScaleEM01_LowPower        = _EMU_STATUS_VSCALE_VSCALE0,
} EMU_VScaleEM01_TypeDef;
#endif

#if defined( _EMU_CTRL_EM23VSCALE_MASK )
/** Supported EM2/3 Voltage Scaling Levels */
typedef enum
{
  /** Fast-wakeup voltage level. */
  emuVScaleEM23_FastWakeup      = _EMU_CTRL_EM23VSCALE_VSCALE2,
  /** Low-power optimized voltage level. Using this voltage level in EM2 and 3
      adds 20-25us to wakeup time if the EM0 and 1 voltage must be scaled
      up to @ref emuVScaleEM01_HighPerformance on EM2 or 3 exit. */
  emuVScaleEM23_LowPower        = _EMU_CTRL_EM23VSCALE_VSCALE0,
} EMU_VScaleEM23_TypeDef;
#endif

#if defined( _EMU_CTRL_EM4HVSCALE_MASK )
/** Supported EM4H Voltage Scaling Levels */
typedef enum
{
  /** Fast-wakeup voltage level. */
  emuVScaleEM4H_FastWakeup      = _EMU_CTRL_EM4HVSCALE_VSCALE2,
  /** Low-power optimized voltage level. Using this voltage level in EM4H
      adds 20-25us to wakeup time if the EM0 and 1 voltage must be scaled
      up to @ref emuVScaleEM01_HighPerformance on EM4H exit. */
  emuVScaleEM4H_LowPower        = _EMU_CTRL_EM4HVSCALE_VSCALE0,
} EMU_VScaleEM4H_TypeDef;
#endif

#if defined(_EMU_EM23PERNORETAINCTRL_MASK)
/** Peripheral EM2 and 3 retention control */
typedef enum
{
  emuPeripheralRetention_LEUART0  = _EMU_EM23PERNORETAINCTRL_LEUART0DIS_MASK,       /* Select LEUART0 retention control  */
  emuPeripheralRetention_CSEN     = _EMU_EM23PERNORETAINCTRL_CSENDIS_MASK,          /* Select CSEN retention control  */
  emuPeripheralRetention_LESENSE0 = _EMU_EM23PERNORETAINCTRL_LESENSE0DIS_MASK,      /* Select LESENSE0 retention control  */
  emuPeripheralRetention_LETIMER0 = _EMU_EM23PERNORETAINCTRL_LETIMER0DIS_MASK,      /* Select LETIMER0 retention control  */
  emuPeripheralRetention_ADC0     = _EMU_EM23PERNORETAINCTRL_ADC0DIS_MASK,          /* Select ADC0 retention control  */
  emuPeripheralRetention_IDAC0    = _EMU_EM23PERNORETAINCTRL_IDAC0DIS_MASK,         /* Select IDAC0 retention control  */
  emuPeripheralRetention_VDAC0    = _EMU_EM23PERNORETAINCTRL_DAC0DIS_MASK,          /* Select DAC0 retention control  */
  emuPeripheralRetention_I2C1     = _EMU_EM23PERNORETAINCTRL_I2C1DIS_MASK,          /* Select I2C1 retention control  */
  emuPeripheralRetention_I2C0     = _EMU_EM23PERNORETAINCTRL_I2C0DIS_MASK,          /* Select I2C0 retention control  */
  emuPeripheralRetention_ACMP1    = _EMU_EM23PERNORETAINCTRL_ACMP1DIS_MASK,         /* Select ACMP1 retention control  */
  emuPeripheralRetention_ACMP0    = _EMU_EM23PERNORETAINCTRL_ACMP0DIS_MASK,         /* Select ACMP0 retention control  */
#if defined( _EMU_EM23PERNORETAINCTRL_PCNT1DIS_MASK )
  emuPeripheralRetention_PCNT2    = _EMU_EM23PERNORETAINCTRL_PCNT2DIS_MASK,         /* Select PCNT2 retention control  */
  emuPeripheralRetention_PCNT1    = _EMU_EM23PERNORETAINCTRL_PCNT1DIS_MASK,         /* Select PCNT1 retention control  */
#endif
  emuPeripheralRetention_PCNT0    = _EMU_EM23PERNORETAINCTRL_PCNT0DIS_MASK,         /* Select PCNT0 retention control  */

  emuPeripheralRetention_D1       = _EMU_EM23PERNORETAINCTRL_LETIMER0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_PCNT0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_ADC0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_ACMP0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_LESENSE0DIS_MASK,/* Select all peripherals in domain 1 */
  emuPeripheralRetention_D2       = _EMU_EM23PERNORETAINCTRL_ACMP1DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_IDAC0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_DAC0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_CSENDIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_LEUART0DIS_MASK
#if defined( _EMU_EM23PERNORETAINCTRL_PCNT1DIS_MASK )
                                        | _EMU_EM23PERNORETAINCTRL_PCNT1DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_PCNT2DIS_MASK
#endif
                                        | _EMU_EM23PERNORETAINCTRL_I2C0DIS_MASK
                                        | _EMU_EM23PERNORETAINCTRL_I2C1DIS_MASK,    /* Select all peripherals in domain 2 */
 emuPeripheralRetention_ALL       = emuPeripheralRetention_D1
                                        | emuPeripheralRetention_D2,                /* Select all peripherals with retention control  */
} EMU_PeripheralRetention_TypeDef;
#endif

/*******************************************************************************
 *******************************   STRUCTS   ***********************************
 ******************************************************************************/

#if defined( _EMU_CMD_EM01VSCALE0_MASK )
/** EM0 and 1 initialization structure. Voltage scaling is applied when
    the core clock frequency is changed from @ref CMU. EM0 an 1 emuVScaleEM01_HighPerformance
    is always enabled. */
typedef struct
{
  bool  vScaleEM01LowPowerVoltageEnable;                 /**< EM0/1 low power voltage status */
} EMU_EM01Init_TypeDef;
#endif

#if defined( _EMU_CMD_EM01VSCALE0_MASK )
/** Default initialization of EM0 and 1 configuration */
#define EMU_EM01INIT_DEFAULT                                                                                    \
{                                                                                                               \
  false                                                  /** Do not scale down in EM0/1 */                      \
}
#endif

/** EM2 and 3 initialization structure  */
typedef struct
{
  bool                          em23VregFullEn;         /**< Enable full VREG drive strength in EM2/3 */
#if defined( _EMU_CTRL_EM23VSCALE_MASK )
  EMU_VScaleEM23_TypeDef        vScaleEM23Voltage;      /**< EM2/3 voltage scaling level */
#endif
} EMU_EM23Init_TypeDef;

/** Default initialization of EM2 and 3 configuration */
#if defined( _EMU_CTRL_EM4HVSCALE_MASK )
#define EMU_EM23INIT_DEFAULT                                                                                    \
{                                                                                                               \
  false,                                                /* Reduced voltage regulator drive strength in EM2/3 */ \
  emuVScaleEM23_FastWakeup,                             /* Do not scale down in EM2/3 */                        \
}
#else
#define EMU_EM23INIT_DEFAULT                                                                                    \
{                                                                                                               \
  false,                                                /* Reduced voltage regulator drive strength in EM2/3 */ \
}
#endif

#if defined( _EMU_EM4CONF_MASK ) || defined( _EMU_EM4CTRL_MASK )
/** EM4 initialization structure  */
typedef struct
{
#if defined( _EMU_EM4CONF_MASK )
  /* Init parameters for platforms with EMU->EM4CONF register (Series 0) */
  bool                        lockConfig;       /**< Lock configuration of regulator, BOD and oscillator */
  bool                        buBodRstDis;      /**< When set, no reset will be asserted due to Brownout when in EM4 */
  EMU_EM4Osc_TypeDef          osc;              /**< EM4 duty oscillator */
  bool                        buRtcWakeup;      /**< Wake up on EM4 BURTC interrupt */
  bool                        vreg;             /**< Enable EM4 voltage regulator */
#elif defined( _EMU_EM4CTRL_MASK )
  /* Init parameters for platforms with EMU->EM4CTRL register (Series 1) */
  bool                        retainLfxo;       /**< Disable the LFXO upon EM4 entry */
  bool                        retainLfrco;      /**< Disable the LFRCO upon EM4 entry */
  bool                        retainUlfrco;     /**< Disable the ULFRCO upon EM4 entry */
  EMU_EM4State_TypeDef        em4State;         /**< Hibernate or shutoff EM4 state */
  EMU_EM4PinRetention_TypeDef pinRetentionMode; /**< EM4 pin retention mode */
#endif
#if defined( _EMU_CTRL_EM4HVSCALE_MASK )
  EMU_VScaleEM4H_TypeDef      vScaleEM4HVoltage;/**< EM4H voltage scaling level */
#endif
} EMU_EM4Init_TypeDef;
#endif

#if defined( _EMU_EM4CONF_MASK )
/** Default initialization of EM4 configuration (Series 0) */
#define EMU_EM4INIT_DEFAULT                                                                \
{                                                                                          \
  false,                              /* Dont't lock configuration after it's been set */  \
  false,                              /* No reset will be asserted due to BOD in EM4 */    \
  emuEM4Osc_ULFRCO,                   /* Use default ULFRCO oscillator  */                 \
  true,                               /* Wake up on EM4 BURTC interrupt */                 \
  true,                               /* Enable VREG */                                    \
}

#elif defined( _EMU_CTRL_EM4HVSCALE_MASK )
/** Default initialization of EM4 configuration (Series 1 with VSCALE) */
#define EMU_EM4INIT_DEFAULT                                                                \
{                                                                                          \
  false,                             /* Retain LFXO configuration upon EM4 entry */        \
  false,                             /* Retain LFRCO configuration upon EM4 entry */       \
  false,                             /* Retain ULFRCO configuration upon EM4 entry */      \
  emuEM4Shutoff,                     /* Use EM4 shutoff state */                           \
  emuPinRetentionDisable,            /* Do not retain pins in EM4 */                       \
  emuVScaleEM4H_FastWakeup,          /* Do not scale down in EM4H */                       \
}

#elif defined( _EMU_EM4CTRL_MASK )
/** Default initialization of EM4 configuration (Series 1 without VSCALE) */
#define EMU_EM4INIT_DEFAULT                                                                \
{                                                                                          \
  false,                             /* Retain LFXO configuration upon EM4 entry */        \
  false,                             /* Retain LFRCO configuration upon EM4 entry */       \
  false,                             /* Retain ULFRCO configuration upon EM4 entry */      \
  emuEM4Shutoff,                     /* Use EM4 shutoff state */                           \
  emuPinRetentionDisable,            /* Do not retain pins in EM4 */                       \
}
#endif

#if defined( BU_PRESENT )
/** Backup Power Domain Initialization structure */
typedef struct
{
  /* Backup Power Domain power configuration */

  /** Voltage probe select, selects ADC voltage */
  EMU_Probe_TypeDef     probe;
  /** Enable BOD calibration mode */
  bool                  bodCal;
  /** Enable BU_STAT status pin for active BU mode */
  bool                  statusPinEnable;

  /* Backup Power Domain connection configuration */
  /** Power domain resistor */
  EMU_Resistor_TypeDef  resistor;
  /** BU_VOUT strong enable */
  bool                  voutStrong;
  /** BU_VOUT medium enable */
  bool                  voutMed;
  /** BU_VOUT weak enable */
  bool                  voutWeak;
  /** Power connection, when not in Backup Mode */
  EMU_Power_TypeDef  inactivePower;
  /** Power connection, when in Backup Mode */
  EMU_Power_TypeDef     activePower;
  /** Enable backup power domain, and release reset, enable BU_VIN pin  */
  bool                  enable;
} EMU_BUPDInit_TypeDef;

/** Default Backup Power Domain configuration */
#define EMU_BUPDINIT_DEFAULT                                              \
{                                                                         \
  emuProbe_Disable, /* Do not enable voltage probe */                     \
  false,            /* Disable BOD calibration mode */                    \
  false,            /* Disable BU_STAT pin for backup mode indication */  \
                                                                          \
  emuRes_Res0,      /* RES0 series resistance between main and backup power */ \
  false,            /* Don't enable strong switch */                           \
  false,            /* Don't enable medium switch */                           \
  false,            /* Don't enable weak switch */                             \
                                                                               \
  emuPower_None,    /* No connection between main and backup power (inactive mode) */     \
  emuPower_None,    /* No connection between main and backup power (active mode) */       \
  true              /* Enable BUPD enter on BOD, enable BU_VIN pin, release BU reset  */  \
}
#endif

#if defined( _EMU_DCDCCTRL_MASK )
/** DCDC initialization structure */
typedef struct
{
  EMU_PowerConfig_TypeDef powerConfig;                  /**< Device external power configuration.
                                                             @ref emuPowerConfig_DcdcToDvdd is currently the only supported mode. */
  EMU_DcdcMode_TypeDef dcdcMode;                        /**< DCDC regulator operating mode in EM0/1 */
  uint16_t mVout;                                       /**< Target output voltage (mV) */
  uint16_t em01LoadCurrent_mA;                          /**< Estimated average load current in EM0/1 (mA).
                                                             This estimate is also used for EM1 optimization,
                                                             so if EM1 current is expected to be higher than EM0,
                                                             then this parameter should hold the higher EM1 current. */
  uint16_t em234LoadCurrent_uA;                         /**< Estimated average load current in EM2 (uA).
                                                             This estimate is also used for EM3 and 4 optimization,
                                                             so if EM3 or 4 current is expected to be higher than EM2,
                                                             then this parameter should hold the higher EM3 or 4 current. */
  uint16_t maxCurrent_mA;                               /**< Maximum average DCDC output current (mA).
                                                             This can be set to the maximum for the power source,
                                                             for example the maximum for a battery. */
  EMU_DcdcAnaPeripheralPower_TypeDef
    anaPeripheralPower;                                 /**< Select analog peripheral power in DCDC-to-DVDD mode */
  EMU_DcdcLnReverseCurrentControl_TypeDef
    reverseCurrentControl;                              /**< Low-noise reverse current control.
                                                             NOTE: this parameter uses special encoding:
                                                             >= 0 is forced CCM mode where the parameter is used as the
                                                                  reverse current threshold in mA.
                                                             -1   is encoded as emuDcdcLnHighEfficiencyMode (EFM32 only) */
  EMU_DcdcLnCompCtrl_TypeDef dcdcLnCompCtrl;            /**< DCDC Low-noise mode compensator control. */
} EMU_DCDCInit_TypeDef;

/** Default DCDC initialization */
#if defined( _EFM_DEVICE )
#if defined(_SILICON_LABS_GECKO_INTERNAL_SDID_80)
#define EMU_DCDCINIT_DEFAULT                                                                                    \
{                                                                                                               \
  emuPowerConfig_DcdcToDvdd,     /* DCDC to DVDD */                                                             \
  emuDcdcMode_LowNoise,          /* Low-niose mode in EM0 */                                                    \
  1800,                          /* Nominal output voltage for DVDD mode, 1.8V  */                              \
  5,                             /* Nominal EM0/1 load current of less than 5mA */                              \
  10,                            /* Nominal EM2/3/4 load current less than 10uA  */                             \
  200,                           /* Maximum average current of 200mA
                                    (assume strong battery or other power source) */                            \
  emuDcdcAnaPeripheralPower_DCDC,/* Select DCDC as analog power supply (lower power) */                         \
  emuDcdcLnHighEfficiency,       /* Use high-efficiency mode */                                                 \
  emuDcdcLnCompCtrl_1u0F,        /* 1uF DCDC capacitor */                                                       \
}
#else
#define EMU_DCDCINIT_DEFAULT                                                                                    \
{                                                                                                               \
  emuPowerConfig_DcdcToDvdd,     /* DCDC to DVDD */                                                             \
  emuDcdcMode_LowPower,          /* Low-power mode in EM0 */                                                    \
  1800,                          /* Nominal output voltage for DVDD mode, 1.8V  */                              \
  5,                             /* Nominal EM0/1 load current of less than 5mA */                              \
  10,                            /* Nominal EM2/3/4 load current less than 10uA  */                             \
  200,                           /* Maximum average current of 200mA
                                    (assume strong battery or other power source) */                            \
  emuDcdcAnaPeripheralPower_DCDC,/* Select DCDC as analog power supply (lower power) */                         \
  emuDcdcLnHighEfficiency,       /* Use high-efficiency mode */                                                 \
  emuDcdcLnCompCtrl_4u7F,        /* 4.7uF DCDC capacitor */                                                     \
}
#endif

#else /* EFR32 device */
#if defined(_SILICON_LABS_GECKO_INTERNAL_SDID_80)
#define EMU_DCDCINIT_DEFAULT                                                                                    \
{                                                                                                               \
  emuPowerConfig_DcdcToDvdd,     /* DCDC to DVDD */                                                             \
  emuDcdcMode_LowNoise,          /* Low-niose mode in EM0 */                                                    \
  1800,                          /* Nominal output voltage for DVDD mode, 1.8V  */                              \
  15,                            /* Nominal EM0/1 load current of less than 15mA */                             \
  10,                            /* Nominal EM2/3/4 load current less than 10uA  */                             \
  200,                           /* Maximum average current of 200mA
                                    (assume strong battery or other power source) */                            \
  emuDcdcAnaPeripheralPower_DCDC,/* Select DCDC as analog power supply (lower power) */                         \
  160,                           /* Maximum reverse current of 160mA */                                         \
  emuDcdcLnCompCtrl_1u0F,        /* 1uF DCDC capacitor */                                                       \
}
#else
#define EMU_DCDCINIT_DEFAULT                                                                                    \
{                                                                                                               \
  emuPowerConfig_DcdcToDvdd,     /* DCDC to DVDD */                                                             \
  emuDcdcMode_LowNoise,          /* Low-niose mode in EM0 */                                                    \
  1800,                          /* Nominal output voltage for DVDD mode, 1.8V  */                              \
  15,                            /* Nominal EM0/1 load current of less than 15mA */                             \
  10,                            /* Nominal EM2/3/4 load current less than 10uA  */                             \
  200,                           /* Maximum average current of 200mA
                                    (assume strong battery or other power source) */                            \
  emuDcdcAnaPeripheralPower_DCDC,/* Select DCDC as analog power supply (lower power) */                         \
  160,                           /* Maximum reverse current of 160mA */                                         \
  emuDcdcLnCompCtrl_4u7F,        /* 4.7uF DCDC capacitor */                                                     \
}
#endif
#endif
#endif

#if defined( EMU_STATUS_VMONRDY )
/** VMON initialization structure */
typedef struct
{
  EMU_VmonChannel_TypeDef channel;      /**< VMON channel to configure */
  int threshold;                        /**< Trigger threshold (mV) */
  bool riseWakeup;                      /**< Wake up from EM4H on rising edge */
  bool fallWakeup;                      /**< Wake up from EM4H on falling edge */
  bool enable;                          /**< Enable VMON channel */
  bool retDisable;                      /**< Disable IO0 retention when voltage drops below threshold (IOVDD only) */
} EMU_VmonInit_TypeDef;

/** Default VMON initialization structure */
#define EMU_VMONINIT_DEFAULT                                                       \
{                                                                                  \
  emuVmonChannel_AVDD,                  /* AVDD VMON channel */                    \
  3200,                                 /* 3.2 V threshold */                      \
  false,                                /* Don't wake from EM4H on rising edge */  \
  false,                                /* Don't wake from EM4H on falling edge */ \
  true,                                 /* Enable VMON channel */                  \
  false                                 /* Don't disable IO0 retention */          \
}

/** VMON Hysteresis initialization structure */
typedef struct
{
  EMU_VmonChannel_TypeDef channel;      /**< VMON channel to configure */
  int riseThreshold;                    /**< Rising threshold (mV) */
  int fallThreshold;                    /**< Falling threshold (mV) */
  bool riseWakeup;                      /**< Wake up from EM4H on rising edge */
  bool fallWakeup;                      /**< Wake up from EM4H on falling edge */
  bool enable;                          /**< Enable VMON channel */
} EMU_VmonHystInit_TypeDef;

/** Default VMON Hysteresis initialization structure */
#define EMU_VMONHYSTINIT_DEFAULT                                                   \
{                                                                                  \
  emuVmonChannel_AVDD,                  /* AVDD VMON channel */                    \
  3200,                                 /* 3.2 V rise threshold */                 \
  3200,                                 /* 3.2 V fall threshold */                 \
  false,                                /* Don't wake from EM4H on rising edge */  \
  false,                                /* Don't wake from EM4H on falling edge */ \
  true                                  /* Enable VMON channel */                  \
}
#endif /* EMU_STATUS_VMONRDY */

/*******************************************************************************
 *****************************   PROTOTYPES   **********************************
 ******************************************************************************/

#if defined( _EMU_CMD_EM01VSCALE0_MASK )
void EMU_EM01Init(const EMU_EM01Init_TypeDef *em01Init);
#endif
void EMU_EM23Init(const EMU_EM23Init_TypeDef *em23Init);
#if defined( _EMU_EM4CONF_MASK ) || defined( _EMU_EM4CTRL_MASK )
void EMU_EM4Init(const EMU_EM4Init_TypeDef *em4Init);
#endif
void EMU_EnterEM2(bool restore);
void EMU_EnterEM3(bool restore);
void EMU_Restore(void);
void EMU_EnterEM4(void);
#if defined( _EMU_EM4CTRL_MASK )
void EMU_EnterEM4H(void);
void EMU_EnterEM4S(void);
#endif
void EMU_MemPwrDown(uint32_t blocks);
void EMU_RamPowerDown(uint32_t start, uint32_t end);
#if defined(_EMU_EM23PERNORETAINCTRL_MASK)
void EMU_PeripheralRetention(EMU_PeripheralRetention_TypeDef periMask, bool enable);
#endif
void EMU_UpdateOscConfig(void);
#if defined( _EMU_CMD_EM01VSCALE0_MASK )
void EMU_VScaleEM01ByClock(uint32_t clockFrequency, bool wait);
void EMU_VScaleEM01(EMU_VScaleEM01_TypeDef voltage, bool wait);
#endif
#if defined( BU_PRESENT )
void EMU_BUPDInit(const EMU_BUPDInit_TypeDef *bupdInit);
void EMU_BUThresholdSet(EMU_BODMode_TypeDef mode, uint32_t value);
void EMU_BUThresRangeSet(EMU_BODMode_TypeDef mode, uint32_t value);
#endif
#if defined( _EMU_DCDCCTRL_MASK )
bool EMU_DCDCInit(const EMU_DCDCInit_TypeDef *dcdcInit);
void EMU_DCDCModeSet(EMU_DcdcMode_TypeDef dcdcMode);
void EMU_DCDCConductionModeSet(EMU_DcdcConductionMode_TypeDef conductionMode, bool rcoDefaultSet);
bool EMU_DCDCOutputVoltageSet(uint32_t mV, bool setLpVoltage, bool setLnVoltage);
void EMU_DCDCOptimizeSlice(uint32_t mALoadCurrent);
void EMU_DCDCLnRcoBandSet(EMU_DcdcLnRcoBand_TypeDef band);
bool EMU_DCDCPowerOff(void);
#endif
#if defined( EMU_STATUS_VMONRDY )
void EMU_VmonInit(const EMU_VmonInit_TypeDef *vmonInit);
void EMU_VmonHystInit(const EMU_VmonHystInit_TypeDef *vmonInit);
void EMU_VmonEnable(EMU_VmonChannel_TypeDef channel, bool enable);
bool EMU_VmonChannelStatusGet(EMU_VmonChannel_TypeDef channel);
#endif

/***************************************************************************//**
 * @brief
 *   Enter energy mode 1 (EM1).
 ******************************************************************************/
__STATIC_INLINE void EMU_EnterEM1(void)
{
  /* Enter sleep mode */
  SCB->SCR &= ~SCB_SCR_SLEEPDEEP_Msk;
  __WFI();
}


#if defined( _EMU_STATUS_VSCALE_MASK )
/***************************************************************************//**
 * @brief
 *   Wait for voltage scaling to complete
 ******************************************************************************/
__STATIC_INLINE void EMU_VScaleWait(void)
{
  while (BUS_RegBitRead(&EMU->STATUS, _EMU_STATUS_VSCALEBUSY_SHIFT));
}
#endif

#if defined( _EMU_STATUS_VSCALE_MASK )
/***************************************************************************//**
 * @brief
 *   Get current voltage scaling level
 *
 * @return
 *    Current voltage scaling level
 ******************************************************************************/
__STATIC_INLINE EMU_VScaleEM01_TypeDef EMU_VScaleGet(void)
{
  EMU_VScaleWait();
  return (EMU_VScaleEM01_TypeDef)((EMU->STATUS & _EMU_STATUS_VSCALE_MASK)
                                  >> _EMU_STATUS_VSCALE_SHIFT);
}
#endif

#if defined( _EMU_STATUS_VMONRDY_MASK )
/***************************************************************************//**
 * @brief
 *   Get the status of the voltage monitor (VMON).
 *
 * @return
 *   Status of the VMON. True if all the enabled channels are ready, false if
 *   one or more of the enabled channels are not ready.
 ******************************************************************************/
__STATIC_INLINE bool EMU_VmonStatusGet(void)
{
  return BUS_RegBitRead(&EMU->STATUS, _EMU_STATUS_VMONRDY_SHIFT);
}
#endif /* _EMU_STATUS_VMONRDY_MASK */

#if defined( _EMU_IF_MASK )
/***************************************************************************//**
 * @brief
 *   Clear one or more pending EMU interrupts.
 *
 * @param[in] flags
 *   Pending EMU interrupt sources to clear. Use one or more valid
 *   interrupt flags for the EMU module (EMU_IFC_nnn).
 ******************************************************************************/
__STATIC_INLINE void EMU_IntClear(uint32_t flags)
{
  EMU->IFC = flags;
}


/***************************************************************************//**
 * @brief
 *   Disable one or more EMU interrupts.
 *
 * @param[in] flags
 *   EMU interrupt sources to disable. Use one or more valid
 *   interrupt flags for the EMU module (EMU_IEN_nnn).
 ******************************************************************************/
__STATIC_INLINE void EMU_IntDisable(uint32_t flags)
{
  EMU->IEN &= ~flags;
}


/***************************************************************************//**
 * @brief
 *   Enable one or more EMU interrupts.
 *
 * @note
 *   Depending on the use, a pending interrupt may already be set prior to
 *   enabling the interrupt. Consider using EMU_IntClear() prior to enabling
 *   if such a pending interrupt should be ignored.
 *
 * @param[in] flags
 *   EMU interrupt sources to enable. Use one or more valid
 *   interrupt flags for the EMU module (EMU_IEN_nnn).
 ******************************************************************************/
__STATIC_INLINE void EMU_IntEnable(uint32_t flags)
{
  EMU->IEN |= flags;
}


/***************************************************************************//**
 * @brief
 *   Get pending EMU interrupt flags.
 *
 * @note
 *   The event bits are not cleared by the use of this function.
 *
 * @return
 *   EMU interrupt sources pending. Returns one or more valid
 *   interrupt flags for the EMU module (EMU_IF_nnn).
 ******************************************************************************/
__STATIC_INLINE uint32_t EMU_IntGet(void)
{
  return EMU->IF;
}


/***************************************************************************//**
 * @brief
 *   Get enabled and pending EMU interrupt flags.
 *   Useful for handling more interrupt sources in the same interrupt handler.
 *
 * @note
 *   Interrupt flags are not cleared by the use of this function.
 *
 * @return
 *   Pending and enabled EMU interrupt sources
 *   The return value is the bitwise AND of
 *   - the enabled interrupt sources in EMU_IEN and
 *   - the pending interrupt flags EMU_IF
 ******************************************************************************/
__STATIC_INLINE uint32_t EMU_IntGetEnabled(void)
{
  uint32_t ien;

  ien = EMU->IEN;
  return EMU->IF & ien;
}


/***************************************************************************//**
 * @brief
 *   Set one or more pending EMU interrupts
 *
 * @param[in] flags
 *   EMU interrupt sources to set to pending. Use one or more valid
 *   interrupt flags for the EMU module (EMU_IFS_nnn).
 ******************************************************************************/
__STATIC_INLINE void EMU_IntSet(uint32_t flags)
{
  EMU->IFS = flags;
}
#endif /* _EMU_IF_MASK */


#if defined( _EMU_EM4CONF_LOCKCONF_MASK )
/***************************************************************************//**
 * @brief
 *   Enable or disable EM4 lock configuration
 * @param[in] enable
 *   If true, locks down EM4 configuration
 ******************************************************************************/
__STATIC_INLINE void EMU_EM4Lock(bool enable)
{
  BUS_RegBitWrite(&(EMU->EM4CONF), _EMU_EM4CONF_LOCKCONF_SHIFT, enable);
}
#endif

#if defined( _EMU_STATUS_BURDY_MASK )
/***************************************************************************//**
 * @brief
 *   Halts until backup power functionality is ready
 ******************************************************************************/
__STATIC_INLINE void EMU_BUReady(void)
{
  while(!(EMU->STATUS & EMU_STATUS_BURDY))
    ;
}
#endif

#if defined( _EMU_ROUTE_BUVINPEN_MASK )
/***************************************************************************//**
 * @brief
 *   Disable BU_VIN support
 * @param[in] enable
 *   If true, enables BU_VIN input pin support, if false disables it
 ******************************************************************************/
__STATIC_INLINE void EMU_BUPinEnable(bool enable)
{
  BUS_RegBitWrite(&(EMU->ROUTE), _EMU_ROUTE_BUVINPEN_SHIFT, enable);
}
#endif

/***************************************************************************//**
 * @brief
 *   Lock the EMU in order to protect its registers against unintended
 *   modification.
 *
 * @note
 *   If locking the EMU registers, they must be unlocked prior to using any
 *   EMU API functions modifying EMU registers, excluding interrupt control
 *   and regulator control if the architecture has a EMU_PWRCTRL register.
 *   An exception to this is the energy mode entering API (EMU_EnterEMn()),
 *   which can be used when the EMU registers are locked.
 ******************************************************************************/
__STATIC_INLINE void EMU_Lock(void)
{
  EMU->LOCK = EMU_LOCK_LOCKKEY_LOCK;
}


/***************************************************************************//**
 * @brief
 *   Unlock the EMU so that writing to locked registers again is possible.
 ******************************************************************************/
__STATIC_INLINE void EMU_Unlock(void)
{
  EMU->LOCK = EMU_LOCK_LOCKKEY_UNLOCK;
}


#if defined( _EMU_PWRLOCK_MASK )
/***************************************************************************//**
 * @brief
 *   Lock the EMU regulator control registers in order to protect against
 *   unintended modification.
 ******************************************************************************/
__STATIC_INLINE void EMU_PowerLock(void)
{
  EMU->PWRLOCK = EMU_PWRLOCK_LOCKKEY_LOCK;
}


/***************************************************************************//**
 * @brief
 *   Unlock the EMU power control registers so that writing to
 *   locked registers again is possible.
 ******************************************************************************/
__STATIC_INLINE void EMU_PowerUnlock(void)
{
  EMU->PWRLOCK = EMU_PWRLOCK_LOCKKEY_UNLOCK;
}
#endif


/***************************************************************************//**
 * @brief
 *   Block entering EM2 or higher number energy modes.
 ******************************************************************************/
__STATIC_INLINE void EMU_EM2Block(void)
{
  BUS_RegBitWrite(&(EMU->CTRL), _EMU_CTRL_EM2BLOCK_SHIFT, 1U);
}

/***************************************************************************//**
 * @brief
 *   Unblock entering EM2 or higher number energy modes.
 ******************************************************************************/
__STATIC_INLINE void EMU_EM2UnBlock(void)
{
  BUS_RegBitWrite(&(EMU->CTRL), _EMU_CTRL_EM2BLOCK_SHIFT, 0U);
}

#if defined( _EMU_EM4CTRL_EM4IORETMODE_MASK )
/***************************************************************************//**
 * @brief
 *   When EM4 pin retention is set to emuPinRetentionLatch, then pins are retained
 *   through EM4 entry and wakeup. The pin state is released by calling this function.
 *   The feature allows peripherals or GPIO to be re-initialized after EM4 exit (reset),
 *   and when the initialization is done, this function can release pins and return control
 *   to the peripherals or GPIO.
 ******************************************************************************/
__STATIC_INLINE void EMU_UnlatchPinRetention(void)
{
  EMU->CMD = EMU_CMD_EM4UNLATCH;
}
#endif

#if defined( _SILICON_LABS_GECKO_INTERNAL_SDID_80 )
void EMU_SetBiasMode(EMU_BiasMode_TypeDef mode);
#endif

/** @} (end addtogroup EMU) */
/** @} (end addtogroup emlib) */

#ifdef __cplusplus
}
#endif

#endif /* defined( EMU_PRESENT ) */
#endif /* EM_EMU_H */