/* SPDX-License-Identifier: Apache-2.0 */

#include <mem.h>
#include <arm/armv7-m.dtsi>
#include <zephyr/dt-bindings/adc/adc.h>
#include <zephyr/dt-bindings/clock/kinetis_sim.h>
#include <zephyr/dt-bindings/clock/kinetis_mcg.h>
#include <zephyr/dt-bindings/gpio/gpio.h>
#include <zephyr/dt-bindings/i2c/i2c.h>

/ {
	aliases {
		watchdog0 = &wdog;
	};

	chosen {
		zephyr,entropy = &rnga;
		zephyr,flash-controller = &ftfe;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-m4f";
			reg = <0>;
		};
	};

	/* The on-chip SRAM is split into SRAM_L and SRAM_U regions that form a
	 * contiguous block in the memory map, however misaligned accesses
	 * across the 0x2000_0000 boundary are not supported in the Arm
	 * Cortex-M4 architecture. For clarity and to avoid the temptation for
	 * someone to extend sram0 without solving this issue, we define two
	 * separate memory nodes here and only use the upper one for now. A
	 * potential solution has been proposed in binutils:
	 * https://sourceware.org/ml/binutils/2017-02/msg00250.html
	 */
	sram_l: memory@1fff0000 {
		compatible = "zephyr,memory-region", "mmio-sram";
		reg = <0x1fff0000 DT_SIZE_K(64)>;
		zephyr,memory-region = "SRAML";
	};

	sram0: memory@20000000 {
		compatible = "mmio-sram";
		reg = <0x20000000 DT_SIZE_K(192)>;
	};

	temp0: temp0 {
		compatible = "nxp,kinetis-temperature";
		io-channels = <&adc0 26>, <&adc0 27>;
		io-channel-names = "SENSOR", "BANDGAP";
		bandgap-voltage = <1000000>;
		vtemp25 = <716000>;
		sensor-slope-cold = <1620>;
		sensor-slope-hot = <1620>;
		status = "disabled";
	};

	temp1: temp1 {
		compatible = "nxp,kinetis-temperature";
		io-channels = <&adc1 26>, <&adc1 27>;
		io-channel-names = "SENSOR", "BANDGAP";
		bandgap-voltage = <1000000>;
		vtemp25 = <716000>;
		sensor-slope-cold = <1620>;
		sensor-slope-hot = <1620>;
		status = "disabled";
	};


	/* Dummy pinctrl node, filled with pin mux options at board level */
	pinctrl: pinctrl {
		compatible = "nxp,kinetis-pinctrl";
		status = "okay";
	};


	soc {
		mpu: mpu@4000d000 {
			compatible = "nxp,k64f-mpu";
			reg = <0x4000d000 0x824>;

			status = "disabled";
		};

		mcg: clock-controller@40064000 {
			compatible = "nxp,kinetis-mcg";
			reg = <0x40064000 0xd>;
			#clock-cells = <1>;
		};

		osc: clock-controller@40065000 {
			compatible = "nxp,k64f-osc";
			reg = <0x40065000 0x4>;

			enable-external-reference;
		};

		rtc: rtc@4003d000 {
			compatible = "nxp,kinetis-rtc";
			reg = <0x4003d000 0x1000>;
			interrupts = <46 0>, <47 0>;
			interrupt-names = "alarm", "seconds";
			clock-frequency = <32768>;
			prescaler = <32768>;
		};

		sim: sim@40047000 {
			compatible = "nxp,kinetis-sim";
			reg = <0x40047000 0x1060>;
			#clock-cells = <3>;

			core_clk {
				compatible = "fixed-factor-clock";
				clocks = <&mcg KINETIS_MCG_OUT_CLK>;
				clock-div = <1>;
				#clock-cells = <0>;
			};

			bus_clk {
				compatible = "fixed-factor-clock";
				clocks = <&mcg KINETIS_MCG_OUT_CLK>;
				clock-div = <2>;
				#clock-cells = <0>;
			};

			flexbus_clk {
				compatible = "fixed-factor-clock";
				clocks = <&mcg KINETIS_MCG_OUT_CLK>;
				clock-div = <3>;
				#clock-cells = <0>;
			};

			flash_clk {
				compatible = "fixed-factor-clock";
				clocks = <&mcg KINETIS_MCG_OUT_CLK>;
				clock-div = <5>;
				#clock-cells = <0>;
			};
		};

		ftfe: flash-controller@40020000 {
			compatible = "nxp,kinetis-ftfe";
			reg = <0x40020000 0x18>;
			interrupts = <18 0>, <19 0>;
			interrupt-names = "command-complete", "read-collision";
			status = "okay";

			#address-cells = <1>;
			#size-cells = <1>;

			flash0: flash@0 {
				compatible = "soc-nv-flash";
				reg = <0 DT_SIZE_M(1)>;
				erase-block-size = <4096>;
				write-block-size = <8>;
			};
		};

		i2c0: i2c@40066000 {
			compatible = "nxp,kinetis-i2c";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40066000 0x1000>;
			interrupts = <24 0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 6>;
			status = "disabled";
		};

		i2c1: i2c@40067000 {
			compatible = "nxp,kinetis-i2c";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x40067000 0x1000>;
			interrupts = <25 0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 7>;
			status = "disabled";
		};

		i2c2: i2c@400e6000 {
			compatible = "nxp,kinetis-i2c";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x400e6000 0x1000>;
			interrupts = <74 0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1028 6>;
			status = "disabled";
		};

		uart0: uart@4006a000 {
			compatible = "nxp,kinetis-uart";
			reg = <0x4006a000 0x1000>;
			interrupts = <31 0>, <32 0>;
			interrupt-names = "status", "error";
			clocks = <&sim KINETIS_SIM_CORESYS_CLK 0x1034 10>;

			status = "disabled";
		};

		uart1: uart@4006b000 {
			compatible = "nxp,kinetis-uart";
			reg = <0x4006b000 0x1000>;
			interrupts = <33 0>, <34 0>;
			interrupt-names = "status", "error";
			clocks = <&sim KINETIS_SIM_CORESYS_CLK 0x1034 11>;

			status = "disabled";
		};

		uart2: uart@4006c000 {
			compatible = "nxp,kinetis-uart";
			reg = <0x4006c000 0x1000>;
			interrupts = <35 0>, <36 0>;
			interrupt-names = "status", "error";
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 12>;

			status = "disabled";
		};

		uart3: uart@4006d000 {
			compatible = "nxp,kinetis-uart";
			reg = <0x4006d000 0x1000>;
			interrupts = <37 0>, <38 0>;
			interrupt-names = "status", "error";
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1034 13>;

			status = "disabled";
		};

		uart4: uart@400ea000 {
			compatible = "nxp,kinetis-uart";
			reg = <0x400ea000 0x1000>;
			interrupts = <66 0>, <67 0>;
			interrupt-names = "status", "error";
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1028 10>;

			status = "disabled";
		};

		uart5: uart@400eb000 {
			compatible = "nxp,kinetis-uart";
			reg = <0x400eb000 0x1000>;
			interrupts = <68 0>, <69 0>;
			interrupt-names = "status", "error";
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1028 11>;

			status = "disabled";
		};

		porta: pinmux@40049000 {
			compatible = "nxp,kinetis-pinmux";
			reg = <0x40049000 0xd0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 9>;
		};

		portb: pinmux@4004a000 {
			compatible = "nxp,kinetis-pinmux";
			reg = <0x4004a000 0xd0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 10>;
		};

		portc: pinmux@4004b000 {
			compatible = "nxp,kinetis-pinmux";
			reg = <0x4004b000 0xd0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 11>;
		};

		portd: pinmux@4004c000 {
			compatible = "nxp,kinetis-pinmux";
			reg = <0x4004c000 0xd0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 12>;
		};

		porte: pinmux@4004d000 {
			compatible = "nxp,kinetis-pinmux";
			reg = <0x4004d000 0xd0>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1038 13>;
		};

		gpioa: gpio@400ff000 {
			compatible = "nxp,kinetis-gpio";
			status = "disabled";
			reg = <0x400ff000 0x40>;
			interrupts = <59 2>;
			gpio-controller;
			#gpio-cells = <2>;
			nxp,kinetis-port = <&porta>;
		};

		gpiob: gpio@400ff040 {
			compatible = "nxp,kinetis-gpio";
			status = "disabled";
			reg = <0x400ff040 0x40>;
			interrupts = <60 2>;
			gpio-controller;
			#gpio-cells = <2>;
			nxp,kinetis-port = <&portb>;
		};

		gpioc: gpio@400ff080 {
			compatible = "nxp,kinetis-gpio";
			status = "disabled";
			reg = <0x400ff080 0x40>;
			interrupts = <61 2>;
			gpio-controller;
			#gpio-cells = <2>;
			nxp,kinetis-port = <&portc>;
		};

		gpiod: gpio@400ff0c0 {
			compatible = "nxp,kinetis-gpio";
			status = "disabled";
			reg = <0x400ff0c0 0x40>;
			interrupts = <62 2>;
			gpio-controller;
			#gpio-cells = <2>;
			nxp,kinetis-port = <&portd>;
		};

		gpioe: gpio@400ff100 {
			compatible = "nxp,kinetis-gpio";
			status = "disabled";
			reg = <0x400ff100 0x40>;
			interrupts = <63 2>;
			gpio-controller;
			#gpio-cells = <2>;
			nxp,kinetis-port = <&porte>;
		};

		spi0: spi@4002c000 {
			compatible = "nxp,kinetis-dspi";
			reg = <0x4002c000 0x88>;
			interrupts = <26 3>;
			dmas = <&edma0 0 14>, <&edma0 0 15>;
			dma-names = "rx", "tx";
			rx-fifo-size = <4>;
			tx-fifo-size = <4>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x103C 12>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spi1: spi@4002d000 {
			compatible = "nxp,kinetis-dspi";
			reg = <0x4002d000 0x88>;
			interrupts = <27 3>;
			dmas = <&edma0 0 16>, <&edma0 0 16>;
			dma-names = "rx", "tx";
			rx-fifo-size = <1>;
			tx-fifo-size = <1>;
			nxp,rx-tx-chn-share;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x103C 13>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spi2: spi@400ac000 {
			compatible = "nxp,kinetis-dspi";
			reg = <0x400ac000 0x88>;
			interrupts = <65 3>;
			dmas = <&edma0 0 38>, <&edma0 0 39>;
			dma-names = "rx", "tx";
			rx-fifo-size = <1>;
			tx-fifo-size = <1>;
			nxp,rx-tx-chn-share;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x1030 12>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		wdog: watchdog@40052000 {
			compatible = "nxp,kinetis-wdog";
			reg = <0x40052000 16>;
			interrupts = <22 0>;
			clocks = <&sim KINETIS_SIM_LPO_CLK 0 0>;
		};

		ftm0: ftm@40038000{
			compatible = "nxp,kinetis-ftm";
			reg = <0x40038000 0x98>;
			interrupts = <42 0>;
			clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
			prescaler = <16>;
			status = "disabled";
		};

		ftm1: ftm@40039000{
			compatible = "nxp,kinetis-ftm";
			reg = <0x40039000 0x98>;
			interrupts = <43 0>;
			clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
			prescaler = <16>;
			status = "disabled";
		};

		ftm2: ftm@4003a000{
			compatible = "nxp,kinetis-ftm";
			reg = <0x4003a000 0x98>;
			interrupts = <44 0>;
			clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
			prescaler = <16>;
			status = "disabled";
		};

		ftm3: ftm@400b9000{
			compatible = "nxp,kinetis-ftm";
			reg = <0x400b9000 0x98>;
			interrupts = <71 0>;
			clocks = <&mcg KINETIS_MCG_FIXED_FREQ_CLK>;
			prescaler = <16>;
			status = "disabled";
		};

		adc0: adc@4003b000{
			compatible = "nxp,kinetis-adc16";
			reg = <0x4003b000 0x70>;
			clocks = <&sim KINETIS_SIM_SIM_SOPT7 0 0xF>,
				<&sim KINETIS_SIM_SIM_SOPT7 7 0x80>;
			dmas = <&edma0 0 40>;
			dma-names = "adc0";
			clk-source = <0>;
			interrupts = <39 0>;
			status = "disabled";
			#io-channel-cells = <1>;
		};

		adc1: adc@400bb000{
			compatible = "nxp,kinetis-adc16";
			reg = <0x400bb000 0x70>;
			clocks = <&sim KINETIS_SIM_SIM_SOPT7 8 0xF00>,
				<&sim KINETIS_SIM_SIM_SOPT7 15 0x8000>;
			dmas = <&edma0 0 41>;
			dma-names = "adc1";
			clk-source = <0>;
			interrupts = <73 0>;
			status = "disabled";
			#io-channel-cells = <1>;
		};

		dac0: dac@400cc000 {
			compatible = "nxp,kinetis-dac";
			reg = <0x400cc000 0x1000>;
			interrupts = <56 0>;
			voltage-reference = <1>;
			status = "disabled";
			#io-channel-cells = <1>;
		};

		dac1: dac@400cd000 {
			compatible = "nxp,kinetis-dac";
			reg = <0x400cd000 0x1000>;
			interrupts = <72 0>;
			voltage-reference = <1>;
			status = "disabled";
			#io-channel-cells = <1>;
		};

		usbotg: usbd@40072000 {
			compatible = "nxp,kinetis-usbd";
			reg = <0x40072000 0x1000>;
			interrupts = <53 1>;
			interrupt-names = "usb_otg";
			num-bidir-endpoints = <16>;
			status = "disabled";
		};

		enet: ethernet@400c0000 {
			compatible = "nxp,kinetis-ethernet";
			reg = <0x400c0000 0x620>;
			interrupts = <83 0>, <84 0>, <85 0>;
			interrupt-names = "TX", "RX", "ERR";
			status = "disabled";
			phy-addr = <0>;
			clocks = <&sim KINETIS_SIM_CORESYS_CLK 0 0>;
			ptp: ptp {
				compatible = "nxp,kinetis-ptp";
				status = "disabled";
				interrupts = <82 0>;
				interrupt-names = "IEEE1588_TMR";
			};
		};

		rnga: random@40029000 {
			compatible = "nxp,kinetis-rnga";
			reg = <0x40029000 0x1000>;
			status = "okay";
			interrupts = <23 0>;
		};

		flexcan0: can@40024000 {
			compatible = "nxp,flexcan";
			reg = <0x40024000 0x1000>;
			interrupts = <75 0>, <76 0>, <77 0>, <78 0>, <79 0>, <80 0>;
			interrupt-names = "mb-0-15", "bus-off", "error", "tx-warning", "rx-warning", "wake-up";
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x103C 4>;
			clk-source = <1>;
			sjw = <1>;
			sample-point = <875>;
			status = "disabled";
		};

		edma0: dma-controller@40008000 {
			#dma-cells = <2>;
			compatible = "nxp,mcux-edma";
			dma-channels = <16>;
			dma-requests = <64>;
			nxp,mem2mem;
			reg = <0x40008000 0x1000>,
				<0x40021000 0x1000>;
			interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
				<4 0>, <5 0>, <6 0>, <7 0>,
				<8 0>, <9 0>, <10 0>, <11 0>,
				<12 0>, <13 0>, <14 0>, <15 0>,
				<16 0>;
			clocks = <&sim KINETIS_SIM_DMA_CLK 0x1040 0x00000002>,
				<&sim KINETIS_SIM_DMAMUX_CLK 0x103C 0x00000002>;
			status = "disabled";
		};

		pit0: pit@40037000 {
			compatible = "nxp,kinetis-pit";
			reg = <0x40037000 0x1000>;
			clocks = <&sim KINETIS_SIM_BUS_CLK 0x103c 23>;
			interrupts = <48 0>, <49 0>, <50 0>, <51 0>;
			status = "disabled";
			pit-channel = <0>;
			pit-period = <1000000>;
			clock-frequency = <60000000>;
		};
	};
};

&nvic {
	arm,num-irq-priority-bits = <4>;
};