/*
 * Copyright (c) 2019 Intel Corporation
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <errno.h>
#include <zephyr.h>
#include <device.h>
#include <soc.h>
#include <drivers/gpio.h>
#include <drivers/espi.h>
#include <drivers/espi_saf.h>
#include <drivers/spi.h>
#include <logging/log_ctrl.h>
#include <logging/log.h>
/* OOB operations will be attempted regardless of channel enabled or not */
#include "espi_oob_handler.h"
LOG_MODULE_DECLARE(espi, CONFIG_ESPI_LOG_LEVEL);

/* eSPI flash parameters */
#define MAX_TEST_BUF_SIZE     1024u
#define MAX_FLASH_REQUEST     64u
#define TARGET_FLASH_REGION   0x72000ul

#define ESPI_FREQ_20MHZ       20u
#define ESPI_FREQ_25MHZ       25u
#define ESPI_FREQ_66MHZ       66u

#define K_WAIT_DELAY          100u

/* eSPI event */
#define EVENT_MASK            0x0000FFFFu
#define EVENT_DETAILS_MASK    0xFFFF0000u
#define EVENT_DETAILS_POS     16u
#define EVENT_TYPE(x)         (x & EVENT_MASK)
#define EVENT_DETAILS(x)      ((x & EVENT_DETAILS_MASK) >> EVENT_DETAILS_POS)

#define PWR_SEQ_TIMEOUT    3000u

/* The devicetree node identifier for the board power rails pins. */
#define BRD_PWR_NODE DT_INST(0, microchip_mec15xx_board_power)

#if DT_NODE_HAS_STATUS(BRD_PWR_NODE, okay)
#define BRD_PWR_PWRGD           DT_GPIO_LABEL(BRD_PWR_NODE, pwrg_gpios)
#define BRD_PWR_RSMRST          DT_GPIO_LABEL(BRD_PWR_NODE, rsm_gpios)
#define BRD_PWR_RSMRST_PIN      DT_GPIO_PIN(BRD_PWR_NODE, rsm_gpios)
#define BRD_PWR_PWRGD_PIN       DT_GPIO_PIN(BRD_PWR_NODE, pwrg_gpios)

static const struct device *pwrgd_dev;
static const struct device *rsm_dev;
#endif

#define ESPI_DEV      DT_LABEL(DT_NODELABEL(espi0))

static const struct device *espi_dev;
static struct espi_callback espi_bus_cb;
static struct espi_callback vw_rdy_cb;
static struct espi_callback vw_cb;
static struct espi_callback p80_cb;
static uint8_t espi_rst_sts;
#ifdef CONFIG_ESPI_OOB_CHANNEL_RX_ASYNC
static struct espi_callback oob_cb;
#endif

#ifdef CONFIG_ESPI_FLASH_CHANNEL
static uint8_t flash_write_buf[MAX_TEST_BUF_SIZE];
static uint8_t flash_read_buf[MAX_TEST_BUF_SIZE];
#endif

#ifdef CONFIG_ESPI_SAF
#define ESPI_SAF_DEV      DT_LABEL(DT_NODELABEL(espi_saf0))
#define SPI_DEV           DT_LABEL(DT_NODELABEL(spi0))

#define SAF_BASE_ADDR     DT_REG_ADDR(DT_INST(0, microchip_xec_espi_saf))

#define SAF_TEST_FREQ_HZ 24000000U
#define SAF_TEST_BUF_SIZE 4096U

/* SPI address of 4KB sector modified by test */
#define SAF_SPI_TEST_ADDRESS 0x1000U

#define SPI_WRITE_STATUS1 0x01U
#define SPI_WRITE_STATUS2 0x31U
#define SPI_WRITE_DISABLE 0x04U
#define SPI_READ_STATUS1 0x05U
#define SPI_WRITE_ENABLE 0x06U
#define SPI_READ_STATUS2 0x35U
#define SPI_WRITE_ENABLE_VS 0x50U
#define SPI_READ_JEDEC_ID 0x9FU

#define SPI_STATUS1_BUSY 0x80U
#define SPI_STATUS2_QE 0x02U

#define W25Q128_JEDEC_ID 0x001840efU

enum saf_erase_size {
	SAF_ERASE_4K = 0,
	SAF_ERASE_32K = 1,
	SAF_ERASE_64K = 2,
	SAF_ERASE_MAX
};

struct saf_addr_info {
	uintptr_t saf_struct_addr;
	uintptr_t saf_exp_addr;
};
static const struct device *qspi_dev;
static const struct device *espi_saf_dev;
static uint8_t safbuf[SAF_TEST_BUF_SIZE] __aligned(4);
static uint8_t safbuf2[SAF_TEST_BUF_SIZE] __aligned(4);

/*
 * W25Q128 SPI flash SAF configuration.
 * Size is 16Mbytes, it requires no continuous mode prefix, or
 * other special SAF configuration.
 */
static const struct espi_saf_flash_cfg flash_w25q128 = {
	.flashsz = 0x1000000U,
	.opa = MCHP_SAF_OPCODE_REG_VAL(0x06U, 0x75U, 0x7aU, 0x05U),
	.opb = MCHP_SAF_OPCODE_REG_VAL(0x20U, 0x52U, 0xd8U, 0x02U),
	.opc = MCHP_SAF_OPCODE_REG_VAL(0xebU, 0xffU, 0xa5U, 0x35U),
	.poll2_mask = MCHP_W25Q128_POLL2_MASK,
	.cont_prefix = 0U,
	.cs_cfg_descr_ids = MCHP_CS0_CFG_DESCR_IDX_REG_VAL,
	.flags = 0,
	.descr = {
		MCHP_W25Q128_CM_RD_D0,
		MCHP_W25Q128_CM_RD_D1,
		MCHP_W25Q128_CM_RD_D2,
		MCHP_W25Q128_ENTER_CM_D0,
		MCHP_W25Q128_ENTER_CM_D1,
		MCHP_W25Q128_ENTER_CM_D2
	}
};

/*
 * SAF driver configuration.
 * One SPI flash device.
 * Use QMSPI frequency, chip select timing, and signal sampling configured
 * by QMSPI driver.
 * Use SAF hardware default TAG map.
 */
static const struct espi_saf_cfg saf_cfg1 = {
	.nflash_devices = 1U,
	.hwcfg = {
		.qmspi_freq_hz = 0U,
		.qmspi_cs_timing = 0U,
		.qmspi_cpha = 0U,
		.flags = 0U,
		.generic_descr = {
			MCHP_SAF_EXIT_CM_DESCR12, MCHP_SAF_EXIT_CM_DESCR13,
			MCHP_SAF_POLL_DESCR14, MCHP_SAF_POLL_DESCR15
		},
		.tag_map = { 0U, 0U, 0U }
	},
	.flash_cfgs = (struct espi_saf_flash_cfg *)&flash_w25q128
};

/*
 * Example for SAF driver set protection regions API.
 */
static const struct espi_saf_pr w25q128_protect_regions[2] = {
	{
		.start = 0xe00000U,
		.size =  0x100000U,
		.master_bm_we = (1U << MCHP_SAF_MSTR_HOST_PCH_ME),
		.master_bm_rd = (1U << MCHP_SAF_MSTR_HOST_PCH_ME),
		.pr_num = 1U,
		.flags = MCHP_SAF_PR_FLAG_ENABLE
			 | MCHP_SAF_PR_FLAG_LOCK,
	},
	{
		.start = 0xf00000U,
		.size =  0x100000U,
		.master_bm_we = (1U << MCHP_SAF_MSTR_HOST_PCH_LAN),
		.master_bm_rd = (1U << MCHP_SAF_MSTR_HOST_PCH_LAN),
		.pr_num = 2U,
		.flags = MCHP_SAF_PR_FLAG_ENABLE
			 | MCHP_SAF_PR_FLAG_LOCK,
	},
};

static const struct espi_saf_protection saf_pr_w25q128 = {
	.nregions = 2U,
	.pregions = w25q128_protect_regions
};

/*
 * Initialize the local attached SPI flash.
 * 1. Get SPI driver binding
 * 2. Read JEDEC ID and verify its a W25Q128
 * 3. Read STATUS2 and check QE bit
 * 4. If QE bit is not set
 *      Send volatile status write enable
 *      Set volatile QE bit
 *      Check STATUS1 BUSY, not expected to be set for volatile status write.
 *      Read STATUS2 and check QE
 * Returns 0 if QE was already set or this routine successfully set volatile
 * QE. Returns < 0 on SPI driver error or unexpected BUSY or STATUS values.
 * NOTE: SPI driver transceive API will configure the SPI controller to the
 * settings passed in the struct spi_config. We set the frequency to the
 * frequency we will be using for SAF.
 */
int spi_saf_init(void)
{
	struct spi_config spi_cfg;
	struct spi_buf_set tx_bufs;
	struct spi_buf_set rx_bufs;
	struct spi_buf txb;
	struct spi_buf rxb;
	uint8_t spi_status1, spi_status2;
	uint32_t jedec_id;
	int ret;

	/* Read JEDEC ID command and fill read buffer */
	safbuf[0] = SPI_READ_JEDEC_ID;
	memset(safbuf2, 0x55, 4U);

	spi_cfg.frequency = SAF_TEST_FREQ_HZ;
	spi_cfg.operation = SPI_OP_MODE_MASTER | SPI_TRANSFER_MSB
			    | SPI_WORD_SET(8);

	/*
	 * Use SPI master mode and inform driver the SPI controller hardware
	 * controls chip select.
	 */
	jedec_id = 0U;
	spi_cfg.slave = 0;
	spi_cfg.cs = NULL;

	txb.buf = &safbuf;
	txb.len = 1U;

	tx_bufs.buffers = (const struct spi_buf *)&txb;
	tx_bufs.count = 1U;

	rxb.buf = &jedec_id;
	rxb.len = 3U;

	rx_bufs.buffers = (const struct spi_buf *)&rxb;
	rx_bufs.count = 1U;

	ret = spi_transceive(qspi_dev, (const struct spi_config *)&spi_cfg,
			     (const struct spi_buf_set *)&tx_bufs,
			     (const struct spi_buf_set *)&rx_bufs);
	if (ret) {
		LOG_ERR("Read JEDEC ID spi_transceive failure: error %d", ret);
		return ret;
	}

	if (jedec_id != W25Q128_JEDEC_ID) {
		LOG_ERR("JEDIC ID does not match W25Q128 %0x", safbuf2[0]);
		return -1;
	}

	/* Read STATUS2 to get quad enable bit */
	safbuf[0] = SPI_READ_STATUS2;
	memset(safbuf2, 0, 4U);

	txb.buf = &safbuf;
	txb.len = 1U;

	tx_bufs.buffers = (const struct spi_buf *)&txb;
	tx_bufs.count = 1U;

	rxb.buf = &safbuf2;
	rxb.len = 1U;

	rx_bufs.buffers = (const struct spi_buf *)&rxb;
	rx_bufs.count = 1U;

	ret = spi_transceive(qspi_dev, (const struct spi_config *)&spi_cfg,
			     (const struct spi_buf_set *)&tx_bufs,
			     (const struct spi_buf_set *)&rx_bufs);
	if (ret) {
		LOG_ERR("Read STATUS2 spi_transceive failure: error %d", ret);
		return ret;
	}

	spi_status2 = safbuf2[0];

	/*
	 * If QE not set then write the volatile QE bit.
	 * SAF test requires SPI flash quad enabled so the WP#/HOLD# signals
	 * will act as IO2/IO3. We will write the volatile QE bit for less
	 * wear of the STATUS2 register
	 */
	if ((spi_status2 & SPI_STATUS2_QE) == 0U) {
		safbuf[0] = SPI_WRITE_ENABLE_VS;

		txb.buf = &safbuf;
		txb.len = 1U;

		tx_bufs.buffers = (const struct spi_buf *)&txb;
		tx_bufs.count = 1U;

		rx_bufs.buffers = NULL;
		rx_bufs.count = 0U;

		ret = spi_transceive(qspi_dev,
				     (const struct spi_config *)&spi_cfg,
				     (const struct spi_buf_set *)&tx_bufs,
				     (const struct spi_buf_set *)&rx_bufs);
		if (ret) {
			LOG_ERR("Send write enable volatile spi_transceive"
				" failure: error %d", ret);
			return ret;
		}

		safbuf[0] = SPI_WRITE_STATUS2;
		safbuf[1] = spi_status2 | SPI_STATUS2_QE;

		txb.buf = &safbuf;
		txb.len = 2U;

		tx_bufs.buffers = (const struct spi_buf *)&txb;
		tx_bufs.count = 1U;

		rx_bufs.buffers = NULL;
		rx_bufs.count = 0U;

		ret = spi_transceive(qspi_dev,
				     (const struct spi_config *)&spi_cfg,
				     (const struct spi_buf_set *)&tx_bufs,
				     (const struct spi_buf_set *)&rx_bufs);
		if (ret) {
			LOG_ERR("Write SPI STATUS2 QE=1 spi_transceive"
				" failure: error %d", ret);
			return ret;
		}

		/* Write to volatile status is fast, expect BUSY to be clear */
		safbuf[0] = SPI_READ_STATUS1;
		memset(safbuf2, 0, 4U);

		txb.buf = &safbuf;
		txb.len = 1U;

		tx_bufs.buffers = (const struct spi_buf *)&txb;
		tx_bufs.count = 1U;

		rxb.buf = &safbuf2;
		/* read 2 bytes both will be STATUS1 */
		rxb.len = 2U;

		rx_bufs.buffers = (const struct spi_buf *)&rxb;
		rx_bufs.count = 1U;

		ret = spi_transceive(qspi_dev,
				     (const struct spi_config *)&spi_cfg,
				     (const struct spi_buf_set *)&tx_bufs,
				     (const struct spi_buf_set *)&rx_bufs);
		if (ret) {
			LOG_ERR("Read SPI STATUS1 spi_transceive"
				" failure: error %d", ret);
			return ret;
		}

		spi_status1 = safbuf2[0];
		if (spi_status1 & SPI_STATUS1_BUSY) {
			LOG_ERR("SPI BUSY set after write to volatile STATUS2:"
				" STATUS1=0x%02X", spi_status1);
			return ret;
		}

		/* Read STATUS2 to make sure QE is set */
		safbuf[0] = SPI_READ_STATUS2;
		memset(safbuf2, 0, 4U);

		txb.buf = &safbuf;
		txb.len = 1U;

		tx_bufs.buffers = (const struct spi_buf *)&txb;
		tx_bufs.count = 1U;

		rxb.buf = &safbuf2;
		/* read 2 bytes both will be STATUS2 */
		rxb.len = 2U;

		rx_bufs.buffers = (const struct spi_buf *)&rxb;
		rx_bufs.count = 1U;

		ret = spi_transceive(qspi_dev,
				     (const struct spi_config *)&spi_cfg,
				     (const struct spi_buf_set *)&tx_bufs,
				     (const struct spi_buf_set *)&rx_bufs);
		if (ret) {
			LOG_ERR("Read 2 of SPI STATUS2  spi_transceive"
				" failure: error %d", ret);
			return ret;
		}

		spi_status2 = safbuf2[0];
		if (!(spi_status2 & SPI_STATUS2_QE)) {
			LOG_ERR("Read back of SPI STATUS2 after setting "
				"volatile QE bit shows QE not set: 0x%02X",
				spi_status2);
			return -1;
		}
	}

	return 0;
}

int espi_saf_init(void)
{
	int ret;

	ret = espi_saf_config(espi_saf_dev, (struct espi_saf_cfg *)&saf_cfg1);
	if (ret) {
		LOG_ERR("Failed to configure eSPI SAF error %d", ret);
	} else {
		LOG_INF("eSPI SAF configured successfully!");
	}

	ret = espi_saf_set_protection_regions(espi_saf_dev,
					      &saf_pr_w25q128);
	if (ret) {
		LOG_ERR("Failed to set SAF protection region(s) %d", ret);
	} else {
		LOG_INF("eSPI SAF protection regions(s) configured!");
	}

	return ret;
}

static int pr_check_range(struct mchp_espi_saf *regs,
			  const struct espi_saf_pr *pr)
{
	uint32_t limit;

	limit = pr->start + pr->size - 1U;

	/* registers b[19:0] = bits[31:12] (align on 4KB) */
	if (regs->SAF_PROT_RG[pr->pr_num].START != (pr->start >> 12)) {
		return -1;
	}

	if (regs->SAF_PROT_RG[pr->pr_num].LIMIT != (limit >> 12)) {
		return -1;
	}

	return 0;
}

static int pr_check_enable(struct mchp_espi_saf *regs,
			   const struct espi_saf_pr *pr)
{
	if (pr->flags & MCHP_SAF_PR_FLAG_ENABLE) {
		if (regs->SAF_PROT_RG[pr->pr_num].LIMIT >
		    regs->SAF_PROT_RG[pr->pr_num].START) {
			return 0;
		}
	} else {
		if (regs->SAF_PROT_RG[pr->pr_num].START >
		    regs->SAF_PROT_RG[pr->pr_num].LIMIT) {
			return 0;
		}
	}

	return -2;
}

static int pr_check_lock(struct mchp_espi_saf *regs,
			 const struct espi_saf_pr *pr)
{
	if (pr->flags & MCHP_SAF_PR_FLAG_LOCK) {
		if (regs->SAF_PROT_LOCK & BIT(pr->pr_num)) {
			return 0;
		}
	} else {
		if (!(regs->SAF_PROT_LOCK & BIT(pr->pr_num))) {
			return 0;
		}
	}

	return -3;
}

/*
 * NOTE: bit[0] of bit map registers is read-only = 1
 */
static int pr_check_master_bm(struct mchp_espi_saf *regs,
			      const struct espi_saf_pr *pr)
{
	if (regs->SAF_PROT_RG[pr->pr_num].WEBM !=
	    (pr->master_bm_we | BIT(0))) {
		return -4;
	}

	if (regs->SAF_PROT_RG[pr->pr_num].RDBM !=
	    (pr->master_bm_rd | BIT(0))) {
		return -4;
	}

	return 0;
}

static int espi_saf_test_pr1(const struct espi_saf_protection *spr)
{
	struct mchp_espi_saf *saf_regs;
	const struct espi_saf_pr *pr;
	int rc;

	LOG_INF("espi_saf_test_pr1");

	if (spr == NULL) {
		return 0;
	}

	saf_regs = (struct mchp_espi_saf *)(SAF_BASE_ADDR);
	pr = spr->pregions;

	for (size_t n = 0U; n < spr->nregions; n++) {
		rc = pr_check_range(saf_regs, pr);
		if (rc) {
			LOG_INF("SAF Protection region %u range fail",
				pr->pr_num);
			return rc;
		}

		rc = pr_check_enable(saf_regs, pr);
		if (rc) {
			LOG_INF("SAF Protection region %u enable fail",
				pr->pr_num);
			return rc;
		}

		rc = pr_check_lock(saf_regs, pr);
		if (rc) {
			LOG_INF("SAF Protection region %u lock check fail",
				pr->pr_num);
			return rc;
		}

		rc = pr_check_master_bm(saf_regs, pr);
		if (rc) {
			LOG_INF("SAF Protection region %u Master select fail",
				pr->pr_num);
			return rc;
		}

		pr++;
	}

	return 0;
}

/*
 * SAF hardware limited to 1 to 64 byte read requests.
 */
static int saf_read(uint32_t spi_addr, uint8_t *dest, int len)
{
	int rc, chunk_len, n;
	struct espi_saf_packet saf_pkt = { 0 };

	if ((dest == NULL) || (len < 0)) {
		return -EINVAL;
	}

	saf_pkt.flash_addr = spi_addr;
	saf_pkt.buf = dest;

	n = len;
	while (n) {
		chunk_len = 64;
		if (n < 64) {
			chunk_len = n;
		}

		saf_pkt.len = chunk_len;

		rc = espi_saf_flash_read(espi_saf_dev, &saf_pkt);
		if (rc != 0) {
			LOG_INF("%s: error = %d: chunk_len = %d "
				"spi_addr = %x", __func__, rc, chunk_len,
				spi_addr);
			return rc;
		}

		saf_pkt.flash_addr += chunk_len;
		saf_pkt.buf += chunk_len;
		n -= chunk_len;
	}

	return len;
}

/*
 * SAF hardware limited to 4KB(mandatory), 32KB, and 64KB erase sizes.
 * eSPI configuration has flags the Host can read specifying supported
 * erase sizes.
 */
static int saf_erase_block(uint32_t spi_addr, enum saf_erase_size ersz)
{
	int rc;
	struct espi_saf_packet saf_pkt = { 0 };

	switch (ersz) {
	case SAF_ERASE_4K:
		saf_pkt.len = 4096U;
		spi_addr &= ~(4096U - 1U);
		break;
	case SAF_ERASE_32K:
		saf_pkt.len = (32U * 1024U);
		spi_addr &= ~((32U * 1024U) - 1U);
		break;
	case SAF_ERASE_64K:
		saf_pkt.len = (64U * 1024U);
		spi_addr &= ~((64U * 1024U) - 1U);
		break;
	default:
		return -EINVAL;
	}

	saf_pkt.flash_addr = spi_addr;

	rc = espi_saf_flash_erase(espi_saf_dev, &saf_pkt);
	if (rc != 0) {
		LOG_INF("espi_saf_test1: erase fail = %d", rc);
		return rc;
	}

	return 0;
}

/*
 * SAF hardware limited to 1 to 64 byte programming within a 256 byte page.
 */
static int saf_page_prog(uint32_t spi_addr, const uint8_t *src, int progsz)
{
	int rc, chunk_len, n;
	struct espi_saf_packet saf_pkt = { 0 };

	if ((src == NULL) || (progsz < 0) || (progsz > 256)) {
		return -EINVAL;
	}

	if (progsz == 0) {
		return 0;
	}

	saf_pkt.flash_addr = spi_addr;
	saf_pkt.buf = (uint8_t *)src;

	n = progsz;
	while (n) {
		chunk_len = 64;
		if (n < 64) {
			chunk_len = n;
		}

		saf_pkt.len = (uint32_t)chunk_len;

		rc = espi_saf_flash_write(espi_saf_dev, &saf_pkt);
		if (rc != 0) {
			LOG_INF("%s: error = %d: erase fail spi_addr = 0x%X",
				__func__, rc, spi_addr);
			return rc;
		}

		saf_pkt.flash_addr += chunk_len;
		saf_pkt.buf += chunk_len;
		n -= chunk_len;
	}

	return progsz;
}


int espi_saf_test1(uint32_t spi_addr)
{
	int rc, retries;
	bool erased;
	uint32_t n, saddr, progsz, chunksz;

	rc = espi_saf_activate(espi_saf_dev);
	LOG_INF("%s: activate = %d", __func__, rc);

	if (spi_addr & 0xfffU) {
		LOG_INF("%s: SPI address 0x%08x not 4KB aligned", __func__,
			spi_addr);
		spi_addr &= ~(4096U-1U);
		LOG_INF("%s: Aligned SPI address to 0x%08x", __func__,
			spi_addr);
	}

	memset(safbuf, 0x55, sizeof(safbuf));
	memset(safbuf2, 0, sizeof(safbuf2));

	erased = false;
	retries = 3;
	while (!erased && (retries-- > 0)) {
		/* read 4KB sector at 0 */
		rc = saf_read(spi_addr, safbuf, 4096);
		if (rc != 4096) {
			LOG_INF("%s: error=%d Read 4K sector at 0x%X failed",
				__func__, rc, spi_addr);
			return rc;
		}

		rc = 0;
		for (n = 0; n < 4096U; n++) {
			if (safbuf[n] != 0xffUL) {
				rc = -1;
				break;
			}
		}

		if (rc == 0) {
			LOG_INF("4KB sector at 0x%x is in erased state. "
				"Continue tests", spi_addr);
			erased = true;
		} else {
			LOG_INF("4KB sector at 0x%x not in erased state. "
				"Send 4K erase.", spi_addr);
			rc = saf_erase_block(spi_addr, SAF_ERASE_4K);
			if (rc != 0) {
				LOG_INF("SAF erase block at 0x%x returned "
					"error %d", spi_addr, rc);
				return rc;
			}
		}
	}

	if (!erased) {
		LOG_INF("%s: Could not erase 4KB sector at 0x%08x",
			__func__, spi_addr);
		return -1;
	}

	/*
	 * Page program test pattern every 256 bytes = 0,1,...,255
	 */
	for (n = 0; n < 4096U; n++) {
		safbuf[n] = n % 256U;
	}

	/* SPI flash sector erase size is 4KB, page program is 256 bytes */
	progsz = 4096U;
	chunksz = 256U;
	saddr = spi_addr;
	n = 0;
	const uint8_t *src = (const uint8_t *)safbuf;

	LOG_INF("%s: Program 4KB sector at 0x%X", __func__, saddr);

	while (n < progsz) {
		rc = saf_page_prog(saddr, (const uint8_t *)src,
				   (int)chunksz);
		if (rc != chunksz) {
			LOG_INF("saf_page_prog error=%d at 0x%X", rc,
				saddr);
			break;
		}
		saddr += chunksz;
		n += chunksz;
		src += chunksz;
	}

	/* read back and check */
	LOG_INF("%s: Read back 4K sector at 0x%X", __func__, spi_addr);

	rc = saf_read(spi_addr, safbuf2, progsz);
	if (rc == progsz) {
		rc = memcmp(safbuf, safbuf2, progsz);
		if (rc == 0) {
			LOG_INF("%s: Read back match: PASS", __func__);
		} else {
			LOG_INF("%s: Read back mismatch: FAIL", __func__);
		}
	} else {
		LOG_INF("%s: Read back 4K error=%d", __func__, rc);
		return rc;
	}

	return rc;
}
#endif /* CONFIG_ESPI_SAF */

static void host_warn_handler(uint32_t signal, uint32_t status)
{
	switch (signal) {
	case ESPI_VWIRE_SIGNAL_HOST_RST_WARN:
		LOG_INF("Host reset warning %d", status);
		if (!IS_ENABLED(CONFIG_ESPI_AUTOMATIC_WARNING_ACKNOWLEDGE)) {
			LOG_INF("HOST RST ACK %d", status);
			espi_send_vwire(espi_dev,
					ESPI_VWIRE_SIGNAL_HOST_RST_ACK,
					status);
		}
		break;
	case ESPI_VWIRE_SIGNAL_SUS_WARN:
		LOG_INF("Host suspend warning %d", status);
		if (!IS_ENABLED(CONFIG_ESPI_AUTOMATIC_WARNING_ACKNOWLEDGE)) {
			LOG_INF("SUS ACK %d", status);
			espi_send_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SUS_ACK,
					status);
		}
		break;
	default:
		break;
	}
}

/* eSPI bus event handler */
static void espi_reset_handler(const struct device *dev,
			       struct espi_callback *cb,
			       struct espi_event event)
{
	if (event.evt_type == ESPI_BUS_RESET) {
		espi_rst_sts = event.evt_data;
		LOG_INF("eSPI BUS reset %d", event.evt_data);
	}
}

/* eSPI logical channels enable/disable event handler */
static void espi_ch_handler(const struct device *dev,
			    struct espi_callback *cb,
			    struct espi_event event)
{
	if (event.evt_type == ESPI_BUS_EVENT_CHANNEL_READY) {
		switch (event.evt_details) {
		case ESPI_CHANNEL_VWIRE:
			LOG_INF("VW channel event %x", event.evt_data);
			break;
		case ESPI_CHANNEL_FLASH:
			LOG_INF("Flash channel event %d", event.evt_data);
			break;
		case ESPI_CHANNEL_OOB:
			LOG_INF("OOB channel event %d", event.evt_data);
			break;
		default:
			LOG_ERR("Unknown channel event");
		}
	}
}

/* eSPI vwire received event handler */
static void vwire_handler(const struct device *dev, struct espi_callback *cb,
			  struct espi_event event)
{
	if (event.evt_type == ESPI_BUS_EVENT_VWIRE_RECEIVED) {
		switch (event.evt_details) {
		case ESPI_VWIRE_SIGNAL_PLTRST:
			LOG_INF("PLT_RST changed %d", event.evt_data);
			break;
		case ESPI_VWIRE_SIGNAL_SLP_S3:
		case ESPI_VWIRE_SIGNAL_SLP_S4:
		case ESPI_VWIRE_SIGNAL_SLP_S5:
			LOG_INF("SLP signal changed %d", event.evt_data);
			break;
		case ESPI_VWIRE_SIGNAL_SUS_WARN:
		case ESPI_VWIRE_SIGNAL_HOST_RST_WARN:
			host_warn_handler(event.evt_details,
					      event.evt_data);
			break;
		}
	}
}

/* eSPI peripheral channel notifications handler */
static void periph_handler(const struct device *dev, struct espi_callback *cb,
			   struct espi_event event)
{
	uint8_t periph_type;
	uint8_t periph_index;

	periph_type = EVENT_TYPE(event.evt_details);
	periph_index = EVENT_DETAILS(event.evt_details);

	switch (periph_type) {
	case ESPI_PERIPHERAL_DEBUG_PORT80:
		LOG_INF("Postcode %x", event.evt_data);
		break;
	case ESPI_PERIPHERAL_HOST_IO:
		LOG_INF("ACPI %x", event.evt_data);
		espi_remove_callback(espi_dev, &p80_cb);
		break;
	default:
		LOG_INF("%s periph 0x%x [%x]", __func__, periph_type,
			event.evt_data);
	}
}

int espi_init(void)
{
	int ret;
	/* Indicate to eSPI master simplest configuration: Single line,
	 * 20MHz frequency and only logical channel 0 and 1 are supported
	 */
	struct espi_cfg cfg = {
		.io_caps = ESPI_IO_MODE_SINGLE_LINE,
		.channel_caps = ESPI_CHANNEL_VWIRE | ESPI_CHANNEL_PERIPHERAL,
		.max_freq = ESPI_FREQ_20MHZ,
	};

	/* If eSPI driver supports additional capabilities use them */
#ifdef CONFIG_ESPI_OOB_CHANNEL
	cfg.channel_caps |= ESPI_CHANNEL_OOB;
#endif
#ifdef CONFIG_ESPI_FLASH_CHANNEL
	cfg.channel_caps |= ESPI_CHANNEL_FLASH;
	cfg.io_caps |= ESPI_IO_MODE_QUAD_LINES;
	cfg.max_freq = ESPI_FREQ_25MHZ;
#endif

	ret = espi_config(espi_dev, &cfg);
	if (ret) {
		LOG_ERR("Failed to configure eSPI slave channels:%x err: %d",
			cfg.channel_caps, ret);
		return ret;
	} else {
		LOG_INF("eSPI slave configured successfully!");
	}

	LOG_INF("eSPI test - callbacks initialization... ");
	espi_init_callback(&espi_bus_cb, espi_reset_handler, ESPI_BUS_RESET);
	espi_init_callback(&vw_rdy_cb, espi_ch_handler,
			   ESPI_BUS_EVENT_CHANNEL_READY);
	espi_init_callback(&vw_cb, vwire_handler,
			   ESPI_BUS_EVENT_VWIRE_RECEIVED);
	espi_init_callback(&p80_cb, periph_handler,
			   ESPI_BUS_PERIPHERAL_NOTIFICATION);
#ifdef CONFIG_ESPI_OOB_CHANNEL_RX_ASYNC
			   espi_init_callback(&oob_cb, oob_rx_handler,
			   ESPI_BUS_EVENT_OOB_RECEIVED);
#endif
	LOG_INF("complete");

	LOG_INF("eSPI test - callbacks registration... ");
	espi_add_callback(espi_dev, &espi_bus_cb);
	espi_add_callback(espi_dev, &vw_rdy_cb);
	espi_add_callback(espi_dev, &vw_cb);
	espi_add_callback(espi_dev, &p80_cb);
#ifdef CONFIG_ESPI_OOB_CHANNEL_RX_ASYNC
	espi_add_callback(espi_dev, &oob_cb);
#endif
	LOG_INF("complete");

	return ret;
}

#if DT_NODE_HAS_STATUS(BRD_PWR_NODE, okay)
static int wait_for_pin(const struct device *dev, uint8_t pin,
			uint16_t timeout,
			int exp_level)
{
	uint16_t loop_cnt = timeout;
	int level;

	do {
		level = gpio_pin_get(dev, pin);
		if (level < 0) {
			LOG_ERR("Failed to read %x %d", pin, level);
			return -EIO;
		}

		if (exp_level == level) {
			LOG_DBG("PIN %x = %x", pin, exp_level);
			break;
		}

		k_usleep(K_WAIT_DELAY);
		loop_cnt--;
	} while (loop_cnt > 0);

	if (loop_cnt == 0) {
		LOG_ERR("Timeout for %x %x", pin, level);
		return -ETIMEDOUT;
	}

	return 0;
}
#endif

static int wait_for_vwire(const struct device *espi_dev,
			  enum espi_vwire_signal signal,
			  uint16_t timeout, uint8_t exp_level)
{
	int ret;
	uint8_t level;
	uint16_t loop_cnt = timeout;

	do {
		ret = espi_receive_vwire(espi_dev, signal, &level);
		if (ret) {
			LOG_ERR("Failed to read %x %d", signal, ret);
			return -EIO;
		}

		if (exp_level == level) {
			break;
		}

		k_usleep(K_WAIT_DELAY);
		loop_cnt--;
	} while (loop_cnt > 0);

	if (loop_cnt == 0) {
		LOG_ERR("VWIRE %d is %x", signal, level);
		return -ETIMEDOUT;
	}

	return 0;
}

static int wait_for_espi_reset(uint8_t exp_sts)
{
	uint16_t loop_cnt = CONFIG_ESPI_VIRTUAL_WIRE_TIMEOUT;

	do {
		if (exp_sts == espi_rst_sts) {
			break;
		}
		k_usleep(K_WAIT_DELAY);
		loop_cnt--;
	} while (loop_cnt > 0);

	if (loop_cnt == 0) {
		return -ETIMEDOUT;
	}

	return 0;
}

int espi_handshake(void)
{
	int ret;

	LOG_INF("eSPI test - Handshake with eSPI master...");
	ret = wait_for_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SUS_WARN,
			     CONFIG_ESPI_VIRTUAL_WIRE_TIMEOUT, 1);
	if (ret) {
		LOG_ERR("SUS_WARN Timeout");
		return ret;
	}

	LOG_INF("1st phase completed");
	ret = wait_for_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SLP_S5,
			     CONFIG_ESPI_VIRTUAL_WIRE_TIMEOUT, 1);
	if (ret) {
		LOG_ERR("SLP_S5 Timeout");
		return ret;
	}

	ret = wait_for_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SLP_S4,
			     CONFIG_ESPI_VIRTUAL_WIRE_TIMEOUT, 1);
	if (ret) {
		LOG_ERR("SLP_S4 Timeout");
		return ret;
	}

	ret = wait_for_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SLP_S3,
			     CONFIG_ESPI_VIRTUAL_WIRE_TIMEOUT, 1);
	if (ret) {
		LOG_ERR("SLP_S3 Timeout");
		return ret;
	}

	LOG_INF("2nd phase completed");

	ret = wait_for_vwire(espi_dev, ESPI_VWIRE_SIGNAL_PLTRST,
			     CONFIG_ESPI_VIRTUAL_WIRE_TIMEOUT, 1);
	if (ret) {
		LOG_ERR("PLT_RST Timeout");
		return ret;
	}

	LOG_INF("3rd phase completed");

	return 0;
}

#ifdef CONFIG_ESPI_FLASH_CHANNEL
int read_test_block(uint8_t *buf, uint32_t start_flash_adr, uint16_t block_len)
{
	uint8_t i = 0;
	uint32_t flash_addr = start_flash_adr;
	uint16_t transactions = block_len/MAX_FLASH_REQUEST;
	int ret = 0;
	struct espi_flash_packet pckt;

	for (i = 0; i < transactions; i++) {
		pckt.buf = buf;
		pckt.flash_addr = flash_addr;
		pckt.len = MAX_FLASH_REQUEST;

		ret = espi_read_flash(espi_dev, &pckt);
		if (ret) {
			LOG_ERR("espi_read_flash failed: %d", ret);
			return ret;
		}

		buf += MAX_FLASH_REQUEST;
		flash_addr += MAX_FLASH_REQUEST;
	}

	LOG_INF("%d read flash transactions completed", transactions);
	return 0;
}

int write_test_block(uint8_t *buf, uint32_t start_flash_adr, uint16_t block_len)
{
	uint8_t i = 0;
	uint32_t flash_addr = start_flash_adr;
	uint16_t transactions = block_len/MAX_FLASH_REQUEST;
	int ret = 0;
	struct espi_flash_packet pckt;

	/* Split operation in multiple MAX_FLASH_REQ transactions */
	for (i = 0; i < transactions; i++) {
		pckt.buf = buf;
		pckt.flash_addr = flash_addr;
		pckt.len = MAX_FLASH_REQUEST;

		ret = espi_write_flash(espi_dev, &pckt);
		if (ret) {
			LOG_ERR("espi_write_flash failed: %d", ret);
			return ret;
		}

		buf += MAX_FLASH_REQUEST;
		flash_addr += MAX_FLASH_REQUEST;
	}

	LOG_INF("%d write flash transactions completed", transactions);
	return 0;
}

static int espi_flash_test(uint32_t start_flash_addr, uint8_t blocks)
{
	uint8_t i;
	uint8_t pattern;
	uint32_t flash_addr;
	int ret = 0;

	LOG_INF("Test eSPI write flash");
	flash_addr = start_flash_addr;
	pattern = 0x99;
	for (i = 0; i <= blocks; i++) {
		memset(flash_write_buf, pattern++, sizeof(flash_write_buf));
		ret = write_test_block(flash_write_buf, flash_addr,
				       sizeof(flash_write_buf));
		if (ret) {
			LOG_ERR("Failed to write to eSPI");
			return ret;
		}

		flash_addr += sizeof(flash_write_buf);
	}

	LOG_INF("Test eSPI read flash");
	flash_addr = start_flash_addr;
	pattern = 0x99;
	for (i = 0; i <= blocks; i++) {
		/* Set expected content */
		memset(flash_write_buf, pattern, sizeof(flash_write_buf));
		/* Clear last read content */
		memset(flash_read_buf, 0, sizeof(flash_read_buf));
		ret = read_test_block(flash_read_buf, flash_addr,
				      sizeof(flash_read_buf));
		if (ret) {
			LOG_ERR("Failed to read from eSPI");
			return ret;
		}

		/* Compare buffers  */
		int cmp = memcmp(flash_write_buf, flash_read_buf,
				 sizeof(flash_write_buf));

		if (cmp != 0) {
			LOG_ERR("eSPI read mismmatch at %d expected %x",
				cmp, pattern);
		}

		flash_addr += sizeof(flash_read_buf);
		pattern++;
	}

	return 0;
}
#endif /* CONFIG_ESPI_FLASH_CHANNEL */

#ifndef CONFIG_ESPI_AUTOMATIC_BOOT_DONE_ACKNOWLEDGE
static void send_slave_bootdone(void)
{
	int ret;
	uint8_t boot_done;

	ret = espi_receive_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SLV_BOOT_DONE,
				 &boot_done);
	LOG_INF("%s boot_done: %d", __func__, boot_done);
	if (ret) {
		LOG_WRN("Fail to retrieve slave boot done");
	} else if (!boot_done) {
		/* SLAVE_BOOT_DONE & SLAVE_LOAD_STS have to be sent together */
		espi_send_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SLV_BOOT_STS, 1);
		espi_send_vwire(espi_dev, ESPI_VWIRE_SIGNAL_SLV_BOOT_DONE, 1);
	}
}
#endif

int espi_test(void)
{
	int ret;

	/* Account for the time serial port is detected so log messages can
	 * be seen
	 */
	k_sleep(K_SECONDS(1));

#if DT_NODE_HAS_STATUS(BRD_PWR_NODE, okay)
	pwrgd_dev = device_get_binding(BRD_PWR_PWRGD);
	if (!pwrgd_dev) {
		LOG_WRN("%s not found", BRD_PWR_PWRGD);
		return -1;
	}

	rsm_dev = device_get_binding(BRD_PWR_RSMRST);
	if (!rsm_dev) {
		LOG_WRN("%s not found", BRD_PWR_RSMRST);
		return -1;
	}

#endif
	espi_dev = device_get_binding(ESPI_DEV);
	if (!espi_dev) {
		LOG_WRN("Fail to find %s", ESPI_DEV);
		return -1;
	}

#ifdef CONFIG_ESPI_SAF
	qspi_dev = device_get_binding(SPI_DEV);
	if (!qspi_dev) {
		LOG_WRN("Fail to find %s", SPI_DEV);
		return -1;
	}

	espi_saf_dev = device_get_binding(ESPI_SAF_DEV);
	if (!espi_saf_dev) {
		LOG_WRN("Fail to find %s", ESPI_SAF_DEV);
		return -1;
	}
#endif

	LOG_INF("Hello eSPI test %s", CONFIG_BOARD);

#if DT_NODE_HAS_STATUS(BRD_PWR_NODE, okay)
	ret = gpio_pin_configure(pwrgd_dev, BRD_PWR_PWRGD_PIN,
				 GPIO_INPUT | GPIO_ACTIVE_HIGH);
	if (ret) {
		LOG_ERR("Unable to configure %d:%d",
			BRD_PWR_PWRGD_PIN, ret);
		return ret;
	}

	ret = gpio_pin_configure(rsm_dev, BRD_PWR_RSMRST_PIN,
				 GPIO_OUTPUT | GPIO_ACTIVE_HIGH);
	if (ret) {
		LOG_ERR("Unable to config %d: %d",
			BRD_PWR_RSMRST_PIN, ret);
		return ret;
	}

	ret = gpio_pin_set(rsm_dev, BRD_PWR_RSMRST_PIN, 0);
	if (ret) {
		LOG_ERR("Unable to initialize %d",
			BRD_PWR_RSMRST_PIN);
		return -1;
	}
#endif

	espi_init();

#ifdef CONFIG_ESPI_SAF
	/*
	 * eSPI SAF configuration must be after eSPI configuration.
	 * eSPI SAF EC portal flash tests before EC releases RSMRST# and
	 * Host de-asserts ESPI_RESET#.
	 */
	ret = spi_saf_init();
	if (ret) {
		LOG_ERR("Unable to configure %d:%s", ret, SPI_DEV);
		return ret;
	}

	ret = espi_saf_init();
	if (ret) {
		LOG_ERR("Unable to configure %d:%s", ret, ESPI_SAF_DEV);
		return ret;
	}


	ret = espi_saf_test_pr1(&saf_pr_w25q128);
	if (ret) {
		LOG_INF("eSPI SAF test pr1 returned error %d", ret);
	}

	ret = espi_saf_test1(SAF_SPI_TEST_ADDRESS);
	if (ret) {
		LOG_INF("eSPI SAF test1 returned error %d", ret);
	}
#endif

#if DT_NODE_HAS_STATUS(BRD_PWR_NODE, okay)
	ret = wait_for_pin(pwrgd_dev, BRD_PWR_PWRGD_PIN,
			   PWR_SEQ_TIMEOUT, 1);
	if (ret) {
		LOG_ERR("RSMRST_PWRGD timeout");
		return ret;
	}

	ret = gpio_pin_set(rsm_dev, BRD_PWR_RSMRST_PIN, 1);
	if (ret) {
		LOG_ERR("Failed to set rsm err: %d", ret);
		return ret;
	}
#endif
	ret = wait_for_espi_reset(1);
	if (ret) {
		LOG_INF("ESPI_RESET timeout");
		return ret;
	}

#ifndef CONFIG_ESPI_AUTOMATIC_BOOT_DONE_ACKNOWLEDGE
	/* When automatic acknowledge is disabled to perform lengthy operations
	 * in the eSPI slave, need to explicitly send slave boot
	 */
	bool vw_ch_sts;

	/* Simulate lengthy operation during boot */
	k_sleep(K_SECONDS(2));

	do {
		vw_ch_sts = espi_get_channel_status(espi_dev,
						    ESPI_CHANNEL_VWIRE);
		k_busy_wait(100);
	} while (!vw_ch_sts);


	send_slave_bootdone();
#endif


#ifdef CONFIG_ESPI_FLASH_CHANNEL
	/* Flash operation need to be perform before VW handshake or
	 * after eSPI host completes full initialization.
	 * This sample code can't assume a full initialized eSPI host
	 * so flash operations are perform here.
	 */
	bool flash_sts;

	do {
		flash_sts = espi_get_channel_status(espi_dev,
						    ESPI_CHANNEL_FLASH);
		k_busy_wait(100);
	} while (!flash_sts);

	/* eSPI flash test can fail and rest of operation can continue */
	ret = espi_flash_test(TARGET_FLASH_REGION, 1);
	if (ret) {
		LOG_INF("eSPI flash test failed %d", ret);
	}
#endif

	/* Showcase VW channel by exchanging virtual wires with eSPI host */
	ret = espi_handshake();
	if (ret) {
		LOG_ERR("eSPI VW handshake failed %d", ret);
		return ret;
	}

	/*  Attempt to use OOB channel to read temperature, regardless of
	 * if is enabled or not.
	 */
#ifndef CONFIG_ESPI_OOB_CHANNEL_RX_ASYNC
	/* System without host-initiated OOB Rx traffic */
	get_pch_temp_sync(espi_dev);
#else
	/* System with host-initiated OOB Rx traffic */
	get_pch_temp_async(espi_dev);
#endif

	/* Cleanup */
	k_sleep(K_SECONDS(1));
	espi_remove_callback(espi_dev, &espi_bus_cb);
	espi_remove_callback(espi_dev, &vw_rdy_cb);
	espi_remove_callback(espi_dev, &vw_cb);

	LOG_INF("eSPI sample completed err: %d", ret);

	return ret;
}

void main(void)
{
	espi_test();
}