/*
 * Copyright (c) 2016 Synopsys, Inc. All rights reserved.
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/**
 * @brief Board configuration macros for EM Starter kit board
 *
 * This header file is used to specify and describe board-level
 * aspects for the target.
 */

#ifndef _BOARD__H_
#define _BOARD__H_

#include <misc/util.h>

/* default system clock */

#define SYSCLK_DEFAULT_IOSC_HZ MHZ(50)
/* On the EM Starter Kit board, the peripheral bus clock frequency is 50Mhz */


/* IRQs */

#define IRQ_TIMER0 16
#define IRQ_TIMER1 17

#ifndef _ASMLANGUAGE

#include <misc/util.h>
#include <drivers/rand32.h>

#define ARCV2_TIMER0_INT_LVL IRQ_TIMER0
#define ARCV2_TIMER0_INT_PRI 0

#define CONFIG_ARCV2_TIMER1_INT_LVL IRQ_TIMER1
#define CONFIG_ARCV2_TIMER1_INT_PRI 1

#define INT_ENABLE_ARC					~(0x00000001 << 8)
#define INT_ENABLE_ARC_BIT_POS				(8)

/* I2C */

/* I2C_0 is on Pmod2 connector */
#define I2C_DW_0_BASE_ADDR                      0xF0004000
#define I2C_DW_0_IRQ                            23


/* I2C_1 is on Pmod4 connector */
#define I2C_DW_1_BASE_ADDR                      0xF0005000
#define I2C_DW_1_IRQ                            24

#define I2C_DW_IRQ_FLAGS			0

/* GPIO */
#define GPIO_DW_0_BASE_ADDR                     0xF0002000 /* GPIO 0 : PORTA */
#define GPIO_DW_0_IRQ                           22
#define GPIO_DW_0_BITS                          32
#define GPIO_DW_PORT_0_INT_MASK                 0 /* n/a */
#define GPIO_DW_0_IRQ_FLAGS			0 /* Defaults */

#define GPIO_DW_1_BASE_ADDR                     0xF000200C /* GPIO 1 : PORTB */
#define GPIO_DW_1_IRQ                           0          /* can't interrupt */
#define GPIO_DW_1_BITS                          9          /* 9 LEDs on board */
#define GPIO_DW_PORT_1_INT_MASK                 0 /* n/a */

#define GPIO_DW_2_BASE_ADDR                     0xF0002018 /* GPIO 2 : PORTC */
#define GPIO_DW_2_IRQ                           0          /* can't interrupt */
#define GPIO_DW_2_BITS                          32
#define GPIO_DW_PORT_2_INT_MASK                 0 /* n/a */

#define GPIO_DW_3_BASE_ADDR                     0xF0002024 /* GPIO 3 : PORTD */
#define GPIO_DW_3_IRQ                           0          /* can't interrupt */
#define GPIO_DW_3_BITS                          12
#define GPIO_DW_PORT_3_INT_MASK                 0 /* n/a */

/* undef GPIO_DW_IO_ACCESS .. because memory mapped */
/* undef CONFIG_GPIO_DW_0_IRQ_SHARED */
/* undef CONFIG_GPIO_DW_CLOCK_GATE */
/* undef CONFIG_SOC_QUARK_SE_C1000_SS */

/* SPI */

#define SPI_DW_SPI_CLOCK     SYSCLK_DEFAULT_IOSC_HZ

#define SPI_DW_PORT_0_REGS   0xF0006000
#define SPI_DW_PORT_1_REGS   0xF0007000

#define SPI_DW_PORT_0_IRQ    25
#define SPI_DW_PORT_1_IRQ    26

#define SPI_DW_IRQ_FLAGS     0

/*
 * SPI Chip Select Assignments on EM Starter Kit
 *
 *  CS0   Pmod6 - pin 1 - J6
 *  CS1   Pmod5 - pin 1 - J5 & Pmod 6 - pin 7 - J6
 *  CS2   Pmod6 - pin 8 - J6
 *  CS3   SDCard (onboard)
 *  CS4   Internal SPI Slave - loopback
 *  CS5   SPI-Flash (onboard)
 */

/*
 * UART
     UART0 vector 27 0xF0008000
     UART1 vector 28 0xF0009000
     UART2 vector 29 0xF000A000
 */
#define UART_NS16550_PORT_0_BASE_ADDR			0xF0008000
#define UART_NS16550_PORT_0_IRQ				27
#define UART_NS16550_PORT_0_CLK_FREQ			SYSCLK_DEFAULT_IOSC_HZ

#define UART_NS16550_PORT_1_BASE_ADDR			0xF0009000
#define UART_NS16550_PORT_1_IRQ				28
#define UART_NS16550_PORT_1_CLK_FREQ			SYSCLK_DEFAULT_IOSC_HZ

#define UART_IRQ_FLAGS					0 /* Default */
#endif /* !_ASMLANGUAGE */

#endif /* _BOARD__H_ */