# Copyright (c) 2023 STMicroelectronics
# SPDX-License-Identifier: Apache-2.0

include: sensor-device.yaml

properties:
  irq-gpios:
    type: phandle-array
    description: |
      DRDY pin

      This pin defaults to active high when produced by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.

  drdy-pin:
    type: int
    default: 1
    enum:
      - 1 # drdy is generated from INT1
      - 2 # drdy is generated from INT2
    description: |
      Select DRDY pin number (1 or 2).

      This number represents which of the two interrupt pins
      (INT1 or INT2) the drdy line is attached to. This property is not
      mandatory and if not present it defaults to 1 which is the
      configuration at power-up.

  accel-range:
    type: int
    default: 0
    description: |
      Range in g. Default is power-up configuration.
    enum:
      - 0 # 2g  (0.061 mg/LSB)
      - 1 # 4g  (0.122 mg/LSB)
      - 2 # 8g  (0.244 mg/LSB)
      - 3 # 16g (0.488 mg/LSB)

  accel-odr:
    type: int
    default: 0x0
    description: |
      Specify the default accelerometer output data rate expressed in samples per second (Hz).
      The values are taken in accordance to lsm6dsv16x_data_rate_t enumerative in hal/st
      module. Please note that this values will not change the operating mode, which will remain
      High Performance (device default)
      Default is power-up configuration.
    enum:
      - 0x00  # Power-Down
      - 0x01  # 1Hz875
      - 0x02  # 7Hz5
      - 0x03  # 15Hz
      - 0x04  # 30Hz
      - 0x05  # 60Hz
      - 0x06  # 120Hz
      - 0x07  # 240Hz
      - 0x08  # 480Hz
      - 0x09  # 960Hz
      - 0x0a  # 1920Hz
      - 0x0b  # 3840Hz
      - 0x0c  # 7680Hz
      - 0x13  # 15Hz625 (High Accuracy 1)
      - 0x14  # 31Hz25  (High Accuracy 1)
      - 0x15  # 62Hz5   (High Accuracy 1)
      - 0x16  # 125Hz   (High Accuracy 1)
      - 0x17  # 250Hz   (High Accuracy 1)
      - 0x18  # 500Hz   (High Accuracy 1)
      - 0x19  # 1000Hz  (High Accuracy 1)
      - 0x1a  # 2000Hz  (High Accuracy 1)
      - 0x1b  # 4000Hz  (High Accuracy 1)
      - 0x1c  # 8000Hz  (High Accuracy 1)
      - 0x23  # 12Hz5   (High Accuracy 2)
      - 0x24  # 25Hz    (High Accuracy 2)
      - 0x25  # 50Hz    (High Accuracy 2)
      - 0x26  # 100Hz   (High Accuracy 2)
      - 0x27  # 200Hz   (High Accuracy 2)
      - 0x28  # 400Hz   (High Accuracy 2)
      - 0x29  # 800Hz   (High Accuracy 2)
      - 0x2a  # 1600Hz  (High Accuracy 2)
      - 0x2b  # 3200Hz  (High Accuracy 2)
      - 0x2c  # 6400Hz  (High Accuracy 2)

  gyro-range:
    type: int
    default: 0
    description: |
      Range in dps. Default is power-up configuration.
    enum:
      - 0 # 125 dps  (4.375 mdps/LSB)
      - 1 # 250 dps  (8.75 mdps/LSB)
      - 2 # 500 dps  (17.50 mdps/LSB)
      - 3 # 1000 dps (35 mdps/LSB)
      - 4 # 2000 dps (70 mdps/LSB)
      - 5 # 4000 dps (140 mdps/LSB)

  gyro-odr:
    type: int
    default: 0x0
    description: |
      Specify the default gyro output data rate expressed in samples per second (Hz).
      The values are taken in accordance to lsm6dsv16x_data_rate_t enumerative in hal/st
      module. Please note that this values will not change the operating mode, which will remain
      High Performance (device default). Moreover, the values here which will be selected in the
      DT are the only way to specifiy the odr accuracy even at runtime with
      SENSOR_ATTR_SAMPLING_FREQUENCY.
      Default is power-up configuration.
    enum:
      - 0x00  # Power-Down
      - 0x02  # 7Hz5
      - 0x03  # 15Hz
      - 0x04  # 30Hz
      - 0x05  # 60Hz
      - 0x06  # 120Hz
      - 0x07  # 240Hz
      - 0x08  # 480Hz
      - 0x09  # 960Hz
      - 0x0a  # 1920Hz
      - 0x0b  # 3840Hz
      - 0x0c  # 7680Hz
      - 0x13  # 15Hz625 (High Accuracy 1)
      - 0x14  # 31Hz25  (High Accuracy 1)
      - 0x15  # 62Hz5   (High Accuracy 1)
      - 0x16  # 125Hz   (High Accuracy 1)
      - 0x17  # 250Hz   (High Accuracy 1)
      - 0x18  # 500Hz   (High Accuracy 1)
      - 0x19  # 1000Hz  (High Accuracy 1)
      - 0x1a  # 2000Hz  (High Accuracy 1)
      - 0x1b  # 4000Hz  (High Accuracy 1)
      - 0x1c  # 8000Hz  (High Accuracy 1)
      - 0x23  # 12Hz5   (High Accuracy 2)
      - 0x24  # 25Hz    (High Accuracy 2)
      - 0x25  # 50Hz    (High Accuracy 2)
      - 0x26  # 100Hz   (High Accuracy 2)
      - 0x27  # 200Hz   (High Accuracy 2)
      - 0x28  # 400Hz   (High Accuracy 2)
      - 0x29  # 800Hz   (High Accuracy 2)
      - 0x2a  # 1600Hz  (High Accuracy 2)
      - 0x2b  # 3200Hz  (High Accuracy 2)
      - 0x2c  # 6400Hz  (High Accuracy 2)

  drdy-pulsed:
    type: boolean
    description: |
      Selects the pulsed mode for data-ready interrupt when enabled,
      and the latched mode when disabled.