.. _stamp_c3:

M5Stack STAMP-C3
##################

Overview
********

STAMP-C3 featuring ESPRESSIF ESP32-C3 RISC-V MCU with Wi-Fi connectivity
for IoT edge devices such as home appliances and Industrial Automation.

For more details see the `M5Stack STAMP-C3`_ page.

Supported Features
==================

The STAMP-C3 board configuration supports the following hardware features:

+-----------+------------+------------------+
| Interface | Controller | Driver/Component |
+===========+============+==================+
| PMP       | on-chip    | arch/riscv       |
+-----------+------------+------------------+
| INTMTRX   | on-chip    | intc_esp32c3     |
+-----------+------------+------------------+
| PINMUX    | on-chip    | pinctrl_esp32    |
+-----------+------------+------------------+
| USB UART  | on-chip    | serial_esp32_usb |
+-----------+------------+------------------+
| GPIO      | on-chip    | gpio_esp32       |
+-----------+------------+------------------+
| UART      | on-chip    | uart_esp32       |
+-----------+------------+------------------+
| I2C       | on-chip    | i2c_esp32        |
+-----------+------------+------------------+
| SPI       | on-chip    | spi_esp32_spim   |
+-----------+------------+------------------+
| TWAI      | on-chip    | can_esp32_twai   |
+-----------+------------+------------------+


Prerequisites
-------------

Espressif HAL requires WiFi and Bluetooth binary blobs in order work. Run the command
below to retrieve those files.

.. code-block:: console

   west blobs fetch hal_espressif

.. note::

   It is recommended running the command above after :file:`west update`.

Building & Flashing
-------------------

Build and flash applications as usual (see :ref:`build_an_application` and
:ref:`application_run` for more details).

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: stamp_c3
   :goals: build

The usual ``flash`` target will work with the ``stamp_c3`` board
configuration. Here is an example for the :ref:`hello_world`
application.

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: stamp_c3
   :goals: flash

Open the serial monitor using the following command:

.. code-block:: shell

   west espressif monitor

After the board has automatically reset and booted, you should see the following
message in the monitor:

.. code-block:: console

   ***** Booting Zephyr OS vx.x.x-xxx-gxxxxxxxxxxxx *****
   Hello World! stamp_c3

Debugging
---------

As with much custom hardware, the ESP32 modules require patches to
OpenOCD that are not upstreamed yet. Espressif maintains their own fork of
the project. The custom OpenOCD can be obtained at `OpenOCD ESP32`_

The Zephyr SDK uses a bundled version of OpenOCD by default. You can overwrite that behavior by adding the
``-DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>``
parameter when building.

Here is an example for building the :ref:`hello_world` application.

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: stamp_c3
   :goals: build flash
   :gen-args: -DOPENOCD=<path/to/bin/openocd> -DOPENOCD_DEFAULT_PATH=<path/to/openocd/share/openocd/scripts>

You can debug an application in the usual way. Here is an example for the :ref:`hello_world` application.

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: stamp_c3
   :goals: debug

References
**********

.. target-notes::

.. _`M5Stack STAMP-C3`: https://docs.m5stack.com/en/core/stamp_c3
.. _`ESP32C3 Technical Reference Manual`: https://espressif.com/sites/default/files/documentation/esp32-c3_technical_reference_manual_en.pdf
.. _`ESP32C3 Datasheet`: https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf
.. _`OpenOCD ESP32`: https://github.com/espressif/openocd-esp32/releases