# HW Info driver configuration options

# Copyright (c) 2019 Alexander Wachter
# SPDX-License-Identifier: Apache-2.0

menuconfig HWINFO
	bool "Hardware Information drivers"
	help
	  Enable hwinfo driver.

if HWINFO

module = HWINFO
module-str = HWINFO
source "subsys/logging/Kconfig.template.log_config"

config HWINFO_HAS_DRIVER
	bool
	help
	  This is an option enabled by individual drivers to signal that there is a hwinfo driver.

config HWINFO_SHELL
	bool "HWINFO Shell"
	depends on SHELL
	help
	  Enable hwinfo Shell for testing.

menuconfig HWINFO_CC13XX_CC26XX
	bool "TI SimpleLink CC13xx/CC26xx hwinfo driver"
	default y
	depends on SOC_SERIES_CC13X2_CC26X2 || SOC_SERIES_CC13X2X7_CC26X2X7
	select HWINFO_HAS_DRIVER
	help
	  Enable TI SimpleLink CC13xx/CC26xx hwinfo driver.

if HWINFO_CC13XX_CC26XX

config HWINFO_CC13XX_CC26XX_ALWAYS_USE_FACTORY_DEFAULT
	bool "Ignore CCFG and always use factory value"
	default y
	help
	  Always return factory pre-programmed values, stored in FCFG and ignore
	  values provided in CCFG (Customer Configuration).

choice
	prompt "Select MAC address type for device ID"
	default HWINFO_CC13XX_CC26XX_USE_IEEE_MAC
	help
	  Specify the MAC address type to be used as device ID by the driver.

config HWINFO_CC13XX_CC26XX_USE_IEEE_MAC
	bool "Use IEEE 802.15.4 extended address"
	help
	  Use 8-bytes length IEEE 802.15.4 extended address as device ID value.

config HWINFO_CC13XX_CC26XX_USE_BLE_MAC
	bool "Use BLE MAC address"
	help
	  Use 6-bytes length BLE MAC address as device ID value.

endchoice

endif # HWINFO_CC13XX_CC26XX

config HWINFO_STM32
	bool "STM32 hwinfo"
	default y
	depends on SOC_FAMILY_STM32 && !SOC_SERIES_STM32WB0X
	select HWINFO_HAS_DRIVER
	help
	  Enable STM32 hwinfo driver.

config HWINFO_NRF
	bool "NRF device ID"
	default y
	depends on SOC_FAMILY_NORDIC_NRF
	depends on SOC_SERIES_NRF54HX || NRF_SOC_SECURE_SUPPORTED
	select HWINFO_HAS_DRIVER
	help
	  Enable Nordic NRF hwinfo driver.

config HWINFO_MCUX_RCM
	bool "NXP kinetis reset cause"
	default y
	depends on HAS_MCUX_RCM
	select HWINFO_HAS_DRIVER
	help
	  Enable NXP kinetis mcux RCM hwinfo driver.

config HWINFO_MCUX_SIM
	bool "NXP kinetis SIM device ID"
	default y
	depends on HAS_MCUX_SIM
	select HWINFO_HAS_DRIVER
	help
	  Enable NXP kinetis mcux SIM hwinfo driver.

config HWINFO_MCUX_SRC
	bool "NXP SRC reset cause"
	default y
	depends on HAS_MCUX_SRC
	select HWINFO_HAS_DRIVER
	help
	  Enable NXP i.MX mcux SRC hwinfo driver.

config HWINFO_MCUX_SRC_V2
	bool "NXP SRC reset cause (multicore devices)"
	default y
	depends on HAS_MCUX_SRC_V2
	select HWINFO_HAS_DRIVER
	help
	  Enable version 2 multicore NXP i.MX mcux SRC hwinfo driver.

config HWINFO_MCUX_SYSCON
	bool "NXP LPC device ID"
	default y
	depends on DT_HAS_NXP_LPC_UID_ENABLED
	select HWINFO_HAS_DRIVER
	help
	  Enable NXP LPC mcux hwinfo driver.

config HWINFO_IMXRT
	bool "NXP i.mx RT device ID"
	default y
	depends on SOC_SERIES_IMXRT10XX || SOC_SERIES_IMXRT11XX
	select HWINFO_HAS_DRIVER
	help
	  Enable NXP i.mx RT hwinfo driver.

config HWINFO_RPI_PICO
	bool "Raspberry Pi Pico hwinfo driver"
	default y
	depends on SOC_SERIES_RP2XXX
	select HWINFO_HAS_DRIVER
	select PICOSDK_USE_FLASH
	help
	  Enable Raspberry Pi Pico hwinfo driver.

config HWINFO_SAM_RSTC
	bool "Atmel SAM reset cause"
	default y
	depends on SOC_FAMILY_ATMEL_SAM && !SOC_SERIES_SAM4L
	select HWINFO_HAS_DRIVER
	help
	  Enable Atmel SAM reset cause hwinfo driver.

config HWINFO_SAM
	bool "Atmel SAM device ID"
	default y
	depends on SOC_FAMILY_ATMEL_SAM && !SOC_SERIES_SAM4L
	select HWINFO_HAS_DRIVER
	help
	  Enable Atmel SAM device ID hwinfo driver.

config HWINFO_SAM4L
	bool "Atmel SAM4L device ID"
	default y
	depends on SOC_SERIES_SAM4L
	select HWINFO_HAS_DRIVER
	help
	  Enable Atmel SAM4L hwinfo driver.

config HWINFO_SAM0
	bool "Atmel SAM0 device ID"
	default y
	depends on SOC_FAMILY_ATMEL_SAM0
	select HWINFO_HAS_DRIVER
	help
	  Enable Atmel SAM0 hwinfo driver.

config HWINFO_SMARTBOND
	bool "Smartbond device reset cause"
	default y
	depends on SOC_FAMILY_RENESAS_SMARTBOND
	select HWINFO_HAS_DRIVER
	help
	  Enable Smartbond reset cause hwinfo driver.

config HWINFO_ESP32
	bool "ESP32 device ID"
	default y
	depends on SOC_FAMILY_ESPRESSIF_ESP32
	select HWINFO_HAS_DRIVER
	help
	  Enable ESP32 hwinfo driver.

config HWINFO_LITEX
	bool "LiteX device ID"
	default y
	depends on SOC_LITEX_VEXRISCV
	depends on DT_HAS_LITEX_DNA0_ENABLED
	select HWINFO_HAS_DRIVER
	help
	  Enable LiteX hwinfo driver

config HWINFO_PSOC6
	bool "Cypress PSOC 6 unique device ID"
	default y
	depends on SOC_FAMILY_PSOC6_LEGACY
	select HWINFO_HAS_DRIVER
	help
	  Enable Cypress PSOC 6 hwinfo driver.

config HWINFO_GECKO
	bool "GECKO hwinfo"
	default y
	depends on SOC_FAMILY_SILABS_S0 || SOC_FAMILY_SILABS_S1 || SOC_FAMILY_SILABS_S2
	depends on !SOC_SERIES_EFR32MG21
	depends on !SOC_SERIES_EFR32BG22
	select HWINFO_HAS_DRIVER
	select SOC_GECKO_RMU
	help
	  Enable Silabs GECKO hwinfo driver.

config HWINFO_ANDES
	bool "Andes system ID"
	default y
	depends on SOC_FAMILY_ANDES_V5
	depends on SYSCON
	select HWINFO_HAS_DRIVER
	help
	  Enable Andes hwinfo driver

config HWINFO_RW61X
	bool "RW61X hwinfo"
	default y
	depends on SOC_SERIES_RW6XX
	select HWINFO_HAS_DRIVER
	help
	  Enable RW61X hwinfo driver

config HWINFO_AMBIQ
	bool "AMBIQ hwinfo"
	default y
	depends on SOC_SERIES_APOLLO4X
	select HWINFO_HAS_DRIVER
	select AMBIQ_HAL
	select AMBIQ_HAL_USE_HWINFO
	help
	  Enable AMBIQ hwinfo driver

config HWINFO_NUMAKER
	bool "NuMaker hwinfo"
	default y
	depends on SOC_SERIES_M46X
	select HWINFO_HAS_DRIVER
	select HAS_NUMAKER_FMC
	help
	  Enable Nuvoton NuMaker hwinfo driver

config HWINFO_NUMAKER_RMC
	bool "NuMaker hwinfo backed up by RMC"
	default y
	depends on SOC_SERIES_M2L31X
	select HWINFO_HAS_DRIVER
	select HAS_NUMAKER_RMC
	help
	  Enable Nuvoton NuMaker hwinfo driver backed up by RMC

endif