/*
 * Copyright (c) 2017 Intel Corporation.
 *
 * SPDX-License-Identifier: Apache-2.0
 */
#include <timestamp.h>


#define CALCULATE_TIME(special_char, profile, name)			     \
	{								     \
		total_##profile##_##name##_time = CYCLES_TO_NS( \
			special_char##profile##_##name##_end_time -	     \
			special_char##profile##_##name##_start_time);	     \
	}

/*total_##profile##_##name##_time =
 * profile##_##name##_end_us - profile##_##name##_start_us;
 */

#define DECLARE_VAR(profile, name) \
	u64_t total_##profile##_##name##_time;

extern u64_t __start_swap_time;
extern u64_t __end_swap_time;
extern u64_t __start_intr_time;
extern u64_t __end_intr_time;
extern u64_t __start_tick_time;
extern u64_t __end_tick_time;

/* NRF RTC TIMER runs ar very slow rate (32KHz), So in order to measure
 * Kernel stats dedicated timer is used to measure kernel stats
 */
#if defined(CONFIG_NRF_RTC_TIMER)
#define NANOSECS_PER_SEC 1000000000
#define CYCLES_PER_SEC (16000000/(1 << NRF_TIMER2->PRESCALER))
/* To get current count of timer, first 1 need to be written into
 * Capture Register and Current Count will be copied into corresponding
 * current count register.
 */
#define GET_CURRENT_TIME()  ((NRF_TIMER2->TASKS_CAPTURE[0] = 1) ?	\
							NRF_TIMER2->CC[0] : 0)
#define CYCLES_TO_NS(x) ((x) * (NANOSECS_PER_SEC/CYCLES_PER_SEC))
#define PRINT_STATS(x, y, z)   PRINT_F(x, (y*((SystemCoreClock)/	\
							CYCLES_PER_SEC)), z)
#define GET_TIMER_VALUE()	GET_CURRENT_TIME()

/* Configure Timer parameters */
static inline void benchmark_timer_init(void)
{
	NRF_TIMER2->TASKS_CLEAR = 1;	/* Clear Timer */
	NRF_TIMER2->MODE = 0;		/* Timer Mode */
	NRF_TIMER2->PRESCALER = 0;	/* 16M Hz */
	NRF_TIMER2->BITMODE = 3;	/* 32 - bit */
}

/* Stop the timer */
static inline void benchmark_timer_stop(void)
{
	NRF_TIMER2->TASKS_STOP = 1;	/* Stop Timer */
}

/*Start the timer */
static inline void benchmark_timer_start(void)
{
	NRF_TIMER2->TASKS_START = 1;	/* Start Timer */
}

/* Get Core Frequency in MHz */
static inline u32_t get_core_freq_MHz(void)
{
	return SystemCoreClock/1000000;
}

#else
#define GET_CURRENT_TIME()  OS_GET_TIME()
#define CYCLES_TO_NS(x) SYS_CLOCK_HW_CYCLES_TO_NS(x)
#define GET_TIMER_VALUE()	SysTick->VAL
/* Dummy functions for timer */
static inline void benchmark_timer_init(void)  {       }
static inline void benchmark_timer_stop(void)  {       }
static inline void benchmark_timer_start(void) {       }

/* Get Core Frequency in MHz */
static inline u32_t get_core_freq_MHz(void)
{
	return  (CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC/1000000);
}

#define PRINT_STATS(x, y, z)   PRINT_F(x, y, z)
#endif /* CONFIG_NRF_RTC_TIMER */

/* Function prototypes */
void system_thread_bench(void);
void yield_bench(void);
void heap_malloc_free_bench(void);
void semaphore_bench(void);
void mutex_bench(void);
void msg_passing_bench(void);

/* PRINT_F
 * Macro to print a formatted output string. fprintf is used when
 * Assumed that sline character array of SLINE_LEN + 1 characters
 * is defined in the main file
 */

/* #define CSV_FORMAT_OUTPUT */
/* printf format defines. */
#ifdef CSV_FORMAT_OUTPUT
#define FORMAT "%-45s,%4u,%5u\n"
#else
#define FORMAT "%-45s:%4u cycles , %5u ns\n"
#endif
#include <stdio.h>

#define GET_2ND_ARG(first, second, ...) (second)
#define GET_3ND_ARG(first, second, third, ...) (third)

/* Enable this macro to print all the measurements.
 * Note: Some measurements in few architectures are not valid
 */
/* #define PRINT_ALL_MEASUREMENTS */
#ifndef PRINT_ALL_MEASUREMENTS
/*If the measured cycles is greater than 10000 then one of the following is
 * possible.
 * 1. the selected measurement is not supported in the architecture
 * 2. The measurement went wrong somewhere.(less likely to happen)
 */
#define PRINT_F(...)						     \
	{							     \
		if ((GET_2ND_ARG(__VA_ARGS__) <= 20000) &&	     \
		    (GET_2ND_ARG(__VA_ARGS__) != 0)) {		     \
			snprintf(sline, 254, FORMAT, ##__VA_ARGS__); \
			TC_PRINT("%s", sline);			     \
		}						     \
	}
#else
/* Prints all outputs*/
#define PRINT_F(...)						     \
	{							     \
		snprintf(sline, 254, FORMAT, ##__VA_ARGS__); \
		TC_PRINT("%s", sline);			     \
	}

#endif


/* If we are using x86 based controller we tend to read the tsc value which is
 * always incrementing i.e count up counter.
 * If we are using the ARM based controllers the systick is a
 * count down counter.
 * If we are using nrf SOC, we are using external timer which always increments
 * ie count up counter.
 * Hence to calculate the cycles taken up by the code we need to adjust the
 * values accordingly.
 *
 * NOTE: Needed only when reading value from end of swap operation
 */
#if CONFIG_ARM
#if defined(CONFIG_SOC_FAMILY_NRF5)
#define SUBTRACT_CLOCK_CYCLES(val) (val)
#else
#define SUBTRACT_CLOCK_CYCLES(val) (SysTick->LOAD - (u32_t) val)
#endif /* CONFIG_SOC_FAMILY_NRF5 */
#else
#define SUBTRACT_CLOCK_CYCLES(val) (val)
#endif /* CONFIG_ARM */