/***************************************************************************//**
 * @file em_i2c.h
 * @brief Inter-intergrated circuit (I2C) peripheral API
 * @version 5.1.2
 *******************************************************************************
 * @section License
 * <b>Copyright 2016 Silicon Laboratories, Inc. http://www.silabs.com</b>
 *******************************************************************************
 *
 * Permission is granted to anyone to use this software for any purpose,
 * including commercial applications, and to alter it and redistribute it
 * freely, subject to the following restrictions:
 *
 * 1. The origin of this software must not be misrepresented; you must not
 *    claim that you wrote the original software.
 * 2. Altered source versions must be plainly marked as such, and must not be
 *    misrepresented as being the original software.
 * 3. This notice may not be removed or altered from any source distribution.
 *
 * DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Silicon Labs has no
 * obligation to support this Software. Silicon Labs is providing the
 * Software "AS IS", with no express or implied warranties of any kind,
 * including, but not limited to, any implied warranties of merchantability
 * or fitness for any particular purpose or warranties against infringement
 * of any proprietary rights of a third party.
 *
 * Silicon Labs will not be liable for any consequential, incidental, or
 * special damages, or any other relief, or for any claim by any third party,
 * arising from your use of this Software.
 *
 ******************************************************************************/

#ifndef EM_I2C_H
#define EM_I2C_H

#include "em_device.h"
#if defined(I2C_COUNT) && (I2C_COUNT > 0)

#include <stdbool.h>

#ifdef __cplusplus
extern "C" {
#endif

/***************************************************************************//**
 * @addtogroup emlib
 * @{
 ******************************************************************************/

/***************************************************************************//**
 * @addtogroup I2C
 * @{
 ******************************************************************************/

/*******************************************************************************
 *******************************   DEFINES   ***********************************
 ******************************************************************************/

/**
 * @brief
 *   Standard mode max frequency assuming using 4:4 ratio for Nlow:Nhigh.
 * @details
 *   From I2C specification: Min Tlow = 4.7us, min Thigh = 4.0us,
 *   max Trise=1.0us, max Tfall=0.3us. Since ratio is 4:4, have to use
 *   worst case value of Tlow or Thigh as base.
 *
 *   1/(Tlow + Thigh + 1us + 0.3us) = 1/(4.7 + 4.7 + 1.3)us = 93458Hz
 * @note
 *   Due to chip characteristics, the max value is somewhat reduced.
 */
#if defined(_SILICON_LABS_32B_SERIES_0)     \
    && (defined(_EFM32_GECKO_FAMILY)        \
        || defined(_EFM32_TINY_FAMILY)      \
        || defined(_EFM32_ZERO_FAMILY)      \
        || defined(_EFM32_HAPPY_FAMILY))
#define I2C_FREQ_STANDARD_MAX    93000
#elif defined(_SILICON_LABS_32B_SERIES_0)   \
      && (defined(_EFM32_GIANT_FAMILY)      \
          || defined(_EFM32_WONDER_FAMILY))
#define I2C_FREQ_STANDARD_MAX    92000
#elif defined(_SILICON_LABS_32B_SERIES_1)
// None of the chips on this platform has been characterized on this parameter.
// Use same value as on Wonder until further notice.
#define I2C_FREQ_STANDARD_MAX    92000
#else
#error "Unknown device family."
#endif

/**
 * @brief
 *   Fast mode max frequency assuming using 6:3 ratio for Nlow:Nhigh.
 * @details
 *   From I2C specification: Min Tlow = 1.3us, min Thigh = 0.6us,
 *   max Trise=0.3us, max Tfall=0.3us. Since ratio is 6:3, have to use
 *   worst case value of Tlow or 2xThigh as base.
 *
 *   1/(Tlow + Thigh + 0.3us + 0.3us) = 1/(1.3 + 0.65 + 0.6)us = 392157Hz
 */
#define I2C_FREQ_FAST_MAX        392157


/**
 * @brief
 *   Fast mode+ max frequency assuming using 11:6 ratio for Nlow:Nhigh.
 * @details
 *   From I2C specification: Min Tlow = 0.5us, min Thigh = 0.26us,
 *   max Trise=0.12us, max Tfall=0.12us. Since ratio is 11:6, have to use
 *   worst case value of Tlow or (11/6)xThigh as base.
 *
 *   1/(Tlow + Thigh + 0.12us + 0.12us) = 1/(0.5 + 0.273 + 0.24)us = 987167Hz
 */
#define I2C_FREQ_FASTPLUS_MAX    987167


/**
 * @brief
 *   Indicate plain write sequence: S+ADDR(W)+DATA0+P.
 * @details
 *   @li S - Start
 *   @li ADDR(W) - address with W/R bit cleared
 *   @li DATA0 - Data taken from buffer with index 0
 *   @li P - Stop
 */
#define I2C_FLAG_WRITE          0x0001

/**
 * @brief
 *   Indicate plain read sequence: S+ADDR(R)+DATA0+P.
 * @details
 *   @li S - Start
 *   @li ADDR(R) - address with W/R bit set
 *   @li DATA0 - Data read into buffer with index 0
 *   @li P - Stop
 */
#define I2C_FLAG_READ           0x0002

/**
 * @brief
 *   Indicate combined write/read sequence: S+ADDR(W)+DATA0+Sr+ADDR(R)+DATA1+P.
 * @details
 *   @li S - Start
 *   @li Sr - Repeated start
 *   @li ADDR(W) - address with W/R bit cleared
 *   @li ADDR(R) - address with W/R bit set
 *   @li DATAn - Data written from/read into buffer with index n
 *   @li P - Stop
 */
#define I2C_FLAG_WRITE_READ     0x0004

/**
 * @brief
 *   Indicate write sequence using two buffers: S+ADDR(W)+DATA0+DATA1+P.
 * @details
 *   @li S - Start
 *   @li ADDR(W) - address with W/R bit cleared
 *   @li DATAn - Data written from buffer with index n
 *   @li P - Stop
 */
#define I2C_FLAG_WRITE_WRITE    0x0008

/** Use 10 bit address. */
#define I2C_FLAG_10BIT_ADDR     0x0010


/*******************************************************************************
 ********************************   ENUMS   ************************************
 ******************************************************************************/

/** Clock low to high ratio settings. */
typedef enum
{
  i2cClockHLRStandard  = _I2C_CTRL_CLHR_STANDARD,      /**< Ratio is 4:4 */
  i2cClockHLRAsymetric = _I2C_CTRL_CLHR_ASYMMETRIC,    /**< Ratio is 6:3 */
  i2cClockHLRFast      = _I2C_CTRL_CLHR_FAST           /**< Ratio is 11:3 */
} I2C_ClockHLR_TypeDef;


/** Return codes for single master mode transfer function. */
typedef enum
{
  /* In progress code (>0) */
  i2cTransferInProgress = 1,    /**< Transfer in progress. */

  /* Complete code (=0) */
  i2cTransferDone       = 0,    /**< Transfer completed successfully. */

  /* Transfer error codes (<0) */
  i2cTransferNack       = -1,   /**< NACK received during transfer. */
  i2cTransferBusErr     = -2,   /**< Bus error during transfer (misplaced START/STOP). */
  i2cTransferArbLost    = -3,   /**< Arbitration lost during transfer. */
  i2cTransferUsageFault = -4,   /**< Usage fault. */
  i2cTransferSwFault    = -5    /**< SW fault. */
} I2C_TransferReturn_TypeDef;


/*******************************************************************************
 *******************************   STRUCTS   ***********************************
 ******************************************************************************/

/** I2C initialization structure. */
typedef struct
{
  /** Enable I2C peripheral when init completed. */
  bool                 enable;

  /** Set to master (true) or slave (false) mode */
  bool                 master;

  /**
   * I2C reference clock assumed when configuring bus frequency setup.
   * Set it to 0 if currently configurated reference clock shall be used
   * This parameter is only applicable if operating in master mode.
   */
  uint32_t             refFreq;

  /**
   * (Max) I2C bus frequency to use. This parameter is only applicable
   * if operating in master mode.
   */
  uint32_t             freq;

  /** Clock low/high ratio control. */
  I2C_ClockHLR_TypeDef clhr;
} I2C_Init_TypeDef;

/** Suggested default config for I2C init structure. */
#define I2C_INIT_DEFAULT                                                  \
{                                                                         \
  true,                    /* Enable when init done */                    \
  true,                    /* Set to master mode */                       \
  0,                       /* Use currently configured reference clock */ \
  I2C_FREQ_STANDARD_MAX,   /* Set to standard rate assuring being */      \
                           /* within I2C spec */                          \
  i2cClockHLRStandard      /* Set to use 4:4 low/high duty cycle */       \
}


/**
 * @brief
 *   Master mode transfer message structure used to define a complete
 *   I2C transfer sequence (from start to stop).
 * @details
 *   The structure allows for defining the following types of sequences,
 *   please refer to defines for sequence details.
 *   @li #I2C_FLAG_READ - data read into buf[0].data
 *   @li #I2C_FLAG_WRITE - data written from buf[0].data
 *   @li #I2C_FLAG_WRITE_READ - data written from buf[0].data and read
 *     into buf[1].data
 *   @li #I2C_FLAG_WRITE_WRITE - data written from buf[0].data and
 *     buf[1].data
 */
typedef struct
{
  /**
   * @brief
   *   Address to use after (repeated) start.
   * @details
   *   Layout details, A = address bit, X = don't care bit (set to 0):
   *   @li 7 bit address - use format AAAA AAAX.
   *   @li 10 bit address - use format XXXX XAAX AAAA AAAA
   */
  uint16_t addr;

  /** Flags defining sequence type and details, see I2C_FLAG_... defines. */
  uint16_t flags;

  /**
   * Buffers used to hold data to send from or receive into depending
   * on sequence type.
   */
  struct
  {
    /** Buffer used for data to transmit/receive, must be @p len long. */
    uint8_t  *data;

    /**
     * Number of bytes in @p data to send or receive. Notice that when
     * receiving data to this buffer, at least 1 byte must be received.
     * Setting @p len to 0 in the receive case is considered a usage fault.
     * Transmitting 0 bytes is legal, in which case only the address
     * is transmitted after the start condition.
     */
    uint16_t len;
  } buf[2];
} I2C_TransferSeq_TypeDef;


/*******************************************************************************
 *****************************   PROTOTYPES   **********************************
 ******************************************************************************/

uint32_t I2C_BusFreqGet(I2C_TypeDef *i2c);
void I2C_BusFreqSet(I2C_TypeDef *i2c,
                    uint32_t freqRef,
                    uint32_t freqScl,
                    I2C_ClockHLR_TypeDef i2cMode);
void I2C_Enable(I2C_TypeDef *i2c, bool enable);
void I2C_Init(I2C_TypeDef *i2c, const I2C_Init_TypeDef *init);

/***************************************************************************//**
 * @brief
 *   Clear one or more pending I2C interrupts.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @param[in] flags
 *   Pending I2C interrupt source to clear. Use a bitwse logic OR combination of
 *   valid interrupt flags for the I2C module (I2C_IF_nnn).
 ******************************************************************************/
__STATIC_INLINE void I2C_IntClear(I2C_TypeDef *i2c, uint32_t flags)
{
  i2c->IFC = flags;
}


/***************************************************************************//**
 * @brief
 *   Disable one or more I2C interrupts.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @param[in] flags
 *   I2C interrupt sources to disable. Use a bitwise logic OR combination of
 *   valid interrupt flags for the I2C module (I2C_IF_nnn).
 ******************************************************************************/
__STATIC_INLINE void I2C_IntDisable(I2C_TypeDef *i2c, uint32_t flags)
{
  i2c->IEN &= ~(flags);
}


/***************************************************************************//**
 * @brief
 *   Enable one or more I2C interrupts.
 *
 * @note
 *   Depending on the use, a pending interrupt may already be set prior to
 *   enabling the interrupt. Consider using I2C_IntClear() prior to enabling
 *   if such a pending interrupt should be ignored.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @param[in] flags
 *   I2C interrupt sources to enable. Use a bitwise logic OR combination of
 *   valid interrupt flags for the I2C module (I2C_IF_nnn).
 ******************************************************************************/
__STATIC_INLINE void I2C_IntEnable(I2C_TypeDef *i2c, uint32_t flags)
{
  i2c->IEN |= flags;
}


/***************************************************************************//**
 * @brief
 *   Get pending I2C interrupt flags.
 *
 * @note
 *   The event bits are not cleared by the use of this function.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @return
 *   I2C interrupt sources pending. A bitwise logic OR combination of valid
 *   interrupt flags for the I2C module (I2C_IF_nnn).
 ******************************************************************************/
__STATIC_INLINE uint32_t I2C_IntGet(I2C_TypeDef *i2c)
{
  return i2c->IF;
}


/***************************************************************************//**
 * @brief
 *   Get enabled and pending I2C interrupt flags.
 *   Useful for handling more interrupt sources in the same interrupt handler.
 *
 * @note
 *   Interrupt flags are not cleared by the use of this function.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @return
 *   Pending and enabled I2C interrupt sources
 *   The return value is the bitwise AND of
 *   - the enabled interrupt sources in I2Cn_IEN and
 *   - the pending interrupt flags I2Cn_IF
 ******************************************************************************/
__STATIC_INLINE uint32_t I2C_IntGetEnabled(I2C_TypeDef *i2c)
{
  uint32_t ien;

  ien = i2c->IEN;
  return i2c->IF & ien;
}


/***************************************************************************//**
 * @brief
 *   Set one or more pending I2C interrupts from SW.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @param[in] flags
 *   I2C interrupt sources to set to pending. Use a bitwise logic OR combination
 *   of valid interrupt flags for the I2C module (I2C_IF_nnn).
 ******************************************************************************/
__STATIC_INLINE void I2C_IntSet(I2C_TypeDef *i2c, uint32_t flags)
{
  i2c->IFS = flags;
}

void I2C_Reset(I2C_TypeDef *i2c);

/***************************************************************************//**
 * @brief
 *   Get slave address used for I2C peripheral (when operating in slave mode).
 *
 * @details
 *   For 10 bit addressing mode, the address is split in two bytes, and only
 *   the first byte setting is fetched, effectively only controlling the 2 most
 *   significant bits of the 10 bit address. Full handling of 10 bit addressing
 *   in slave mode requires additional SW handling.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @return
 *   I2C slave address in use. The 7 most significant bits define the actual
 *   address, the least significant bit is reserved and always returned as 0.
 ******************************************************************************/
__STATIC_INLINE uint8_t I2C_SlaveAddressGet(I2C_TypeDef *i2c)
{
  return ((uint8_t)(i2c->SADDR));
}


/***************************************************************************//**
 * @brief
 *   Set slave address to use for I2C peripheral (when operating in slave mode).
 *
 * @details
 *   For 10 bit addressing mode, the address is split in two bytes, and only
 *   the first byte is set, effectively only controlling the 2 most significant
 *   bits of the 10 bit address. Full handling of 10 bit addressing in slave
 *   mode requires additional SW handling.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @param[in] addr
 *   I2C slave address to use. The 7 most significant bits define the actual
 *   address, the least significant bit is reserved and always set to 0.
 ******************************************************************************/
__STATIC_INLINE void I2C_SlaveAddressSet(I2C_TypeDef *i2c, uint8_t addr)
{
  i2c->SADDR = (uint32_t)addr & 0xfe;
}


/***************************************************************************//**
 * @brief
 *   Get slave address mask used for I2C peripheral (when operating in slave
 *   mode).
 *
 * @details
 *   The address mask defines how the comparator works. A bit position with
 *   value 0 means that the corresponding slave address bit is ignored during
 *   comparison (don't care). A bit position with value 1 means that the
 *   corresponding slave address bit must match.
 *
 *   For 10 bit addressing mode, the address is split in two bytes, and only
 *   the mask for the first address byte is fetched, effectively only
 *   controlling the 2 most significant bits of the 10 bit address.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @return
 *   I2C slave address mask in use. The 7 most significant bits define the
 *   actual address mask, the least significant bit is reserved and always
 *   returned as 0.
 ******************************************************************************/
__STATIC_INLINE uint8_t I2C_SlaveAddressMaskGet(I2C_TypeDef *i2c)
{
  return ((uint8_t)(i2c->SADDRMASK));
}


/***************************************************************************//**
 * @brief
 *   Set slave address mask used for I2C peripheral (when operating in slave
 *   mode).
 *
 * @details
 *   The address mask defines how the comparator works. A bit position with
 *   value 0 means that the corresponding slave address bit is ignored during
 *   comparison (don't care). A bit position with value 1 means that the
 *   corresponding slave address bit must match.
 *
 *   For 10 bit addressing mode, the address is split in two bytes, and only
 *   the mask for the first address byte is set, effectively only controlling
 *   the 2 most significant bits of the 10 bit address.
 *
 * @param[in] i2c
 *   Pointer to I2C peripheral register block.
 *
 * @param[in] mask
 *   I2C slave address mask to use. The 7 most significant bits define the
 *   actual address mask, the least significant bit is reserved and should
 *   be 0.
 ******************************************************************************/
__STATIC_INLINE void I2C_SlaveAddressMaskSet(I2C_TypeDef *i2c, uint8_t mask)
{
  i2c->SADDRMASK = (uint32_t)mask & 0xfe;
}


I2C_TransferReturn_TypeDef I2C_Transfer(I2C_TypeDef *i2c);
I2C_TransferReturn_TypeDef I2C_TransferInit(I2C_TypeDef *i2c,
                                            I2C_TransferSeq_TypeDef *seq);

/** @} (end addtogroup I2C) */
/** @} (end addtogroup emlib) */

#ifdef __cplusplus
}
#endif

#endif /* defined(I2C_COUNT) && (I2C_COUNT > 0) */
#endif /* EM_I2C_H */