blob: 3e5f0ef9a3609120cdf196321cb8df9a22ec2e2c [file] [log] [blame]
# STM32 HAL Ethernet driver configuration options
# Copyright (c) 2017 Erwin Rol <erwin@erwinrol.com>
# Copyright (c) 2020 Alexander Kozhinov <AlexanderKozhinov@yandex.com>
# SPDX-License-Identifier: Apache-2.0
menuconfig ETH_STM32_HAL
bool "STM32 HAL Ethernet driver"
default y
depends on DT_HAS_ST_STM32_ETHERNET_ENABLED
select USE_STM32_HAL_ETH
select NOCACHE_MEMORY if SOC_SERIES_STM32H7X && CPU_CORTEX_M7
help
Enable STM32 HAL based Ethernet driver. It is available for
all Ethernet enabled variants of the F2, F4, F7 and H7 series.
if ETH_STM32_HAL
config ETH_STM32_HAL_RX_THREAD_STACK_SIZE
int "RX thread stack size"
default 1500
help
RX thread stack size
config ETH_STM32_HAL_RX_THREAD_PRIO
int "RX thread priority"
default 2
help
RX thread priority
config ETH_STM32_HAL_USE_DTCM_FOR_DMA_BUFFER
bool "Use DTCM for DMA buffers"
default y
depends on SOC_SERIES_STM32F7X
help
When this option is activated, the buffers for DMA transfer are
moved from SRAM to the DTCM (Data Tightly Coupled Memory).
config ETH_STM32_HAL_PHY_ADDRESS
int "Phy address"
default 0
help
The phy address to use.
config ETH_STM32_HAL_RANDOM_MAC
bool "Random MAC address"
depends on ENTROPY_GENERATOR
default y
help
Generate a random MAC address dynamically.
if !ETH_STM32_HAL_RANDOM_MAC
config ETH_STM32_HAL_MAC3
hex "MAC Address Byte 3"
default 0
range 0 0xff
help
This is the byte 3 of the MAC address.
config ETH_STM32_HAL_MAC4
hex "MAC Address Byte 4"
default 0
range 0 0xff
help
This is the byte 4 of the MAC address.
config ETH_STM32_HAL_MAC5
hex "MAC Address Byte 5"
default 0
range 0 0xff
help
This is the byte 5 of the MAC address.
endif # !ETH_STM32_HAL_RANDOM_MAC
config ETH_STM32_HAL_MII
bool "Use MII interface"
help
Use the MII physical interface instead of RMII.
config ETH_STM32_CARRIER_CHECK_RX_IDLE_TIMEOUT_MS
int "Carrier check timeout period (ms)"
default 500
range 100 30000
help
Set the RX idle timeout period in milliseconds after which the
PHY's carrier status is re-evaluated.
config ETH_STM32_AUTO_NEGOTIATION_ENABLE
bool "Autonegotiation mode"
default y
help
Enable this if using autonegotiation
if !ETH_STM32_AUTO_NEGOTIATION_ENABLE
config ETH_STM32_SPEED_10M
bool "Set speed to 10 Mbps when autonegotiation is disabled"
help
Set this if using 10 Mbps and when autonegotiation is disabled, otherwise speed
is 100 Mbps
config ETH_STM32_MODE_HALFDUPLEX
bool "Half duplex mode"
help
Set this if using half duplex when autonegotiation is disabled otherwise
duplex mode is full duplex
endif # !ETH_STM32_AUTO_NEGOTIATION_ENABLE
if SOC_SERIES_STM32F7X || SOC_SERIES_STM32H7X
config PTP_CLOCK_STM32_HAL
bool "STM32 HAL PTP clock driver support"
default y
depends on PTP_CLOCK || NET_L2_PTP
help
Enable STM32 PTP clock support.
config ETH_STM32_HAL_PTP_CLOCK_SRC_HZ
int "Frequency of the clock source for the PTP timer"
default 50000000
depends on PTP_CLOCK_STM32_HAL
help
Set the frequency in Hz sourced to the PTP timer.
If the value is set properly, the timer will be accurate.
config ETH_STM32_HAL_PTP_CLOCK_ADJ_MIN_PCT
int "Lower bound of clock frequency adjustment (in percent)"
default 90
depends on PTP_CLOCK_STM32_HAL
help
Specifies lower bound of PTP clock rate adjustment.
config ETH_STM32_HAL_PTP_CLOCK_ADJ_MAX_PCT
int "Upper bound of clock frequency adjustment (in percent)"
default 110
depends on PTP_CLOCK_STM32_HAL
help
Specifies upper bound of PTP clock rate adjustment.
config ETH_STM32_HAL_PTP_CLOCK_INIT_PRIO
int
default 85
depends on PTP_CLOCK_STM32_HAL
help
STM32 PTP Clock initialization priority level. There is
a dependency from the network stack that this device
initializes before network stack (NET_INIT_PRIO).
endif # SOC_SERIES_STM32F7X || SOC_SERIES_STM32H7X
endif # ETH_STM32_HAL