boards/arm/mimxrt1024_evk/doc/index.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _mimxrt1024_evk:

 NXP MIMXRT1024-EVK
 ##################

 Overview
 ********

 The i.MX RT1024 expands the i.MX RT crossover processor families by providing
 high-performance feature set in low-cost LQFP packages, further simplifying
 board design and layout for customers. The i.MX RT1024 runs on the Arm®
 Cortex®-M7 core at 500 MHz.

 .. image:: ./mimxrt1024_evk.jpg
    :width: 720px
    :align: center
    :alt: MIMXRT1024-EVK

 Hardware
 ********

 - MIMXRT1024DAG5A MCU (600 MHz, 256 KB on-chip memory, 4096KB on-chip QSPI
   flash)

 - Memory

   - 256 Mbit SDRAM
   - 64 Mbit QSPI Flash
   - TF socket for SD card

 - Connectivity

   - 10/100 Mbit/s Ethernet PHY
   - Micro USB host and OTG connectors
   - CAN transceivers
   - Arduino interface

 - Audio

   - Audio Codec
   - 4-pole audio headphone jack
   - Microphone
   - External speaker connection

 - Power

   - 5 V DC jack

 - Debug

   - JTAG 10-pin connector
   - OpenSDA with DAPLink

 - Sensor

   - 6-axis FXOS8700CQ digital accelerometer and magnetometer

 For more information about the MIMXRT1024 SoC and MIMXRT1024-EVK board, see
 these references:

 - `i.MX RT1024 Website`_
 - `i.MX RT1024 Datasheet`_
 - `i.MX RT1024 Reference Manual`_
 - `MIMXRT1024-EVK Website`_
 - `MIMXRT1024-EVK User Guide`_
 - `MIMXRT1024-EVK Design Files`_

 Supported Features
 ==================

 The mimxrt1024_evk board configuration supports the following hardware
 features:

 +-----------+------------+-------------------------------------+
 | Interface | Controller | Driver/Component                    |
 +===========+============+=====================================+
 | NVIC      | on-chip    | nested vector interrupt controller  |
 +-----------+------------+-------------------------------------+
 | SYSTICK   | on-chip    | systick                             |
 +-----------+------------+-------------------------------------+
 | FLASH     | on-chip    | QSPI flash                          |
 +-----------+------------+-------------------------------------+
 | GPIO      | on-chip    | gpio                                |
 +-----------+------------+-------------------------------------+
 | UART      | on-chip    | serial port-polling;                |
 |           |            | serial port-interrupt               |
 +-----------+------------+-------------------------------------+
 | SPI       | on-chip    | spi                                 |
 +-----------+------------+-------------------------------------+
 | ENET      | on-chip    | ethernet                            |
 +-----------+------------+-------------------------------------+
 | CAN       | on-chip    | can                                 |
 +-----------+------------+-------------------------------------+
 | WATCHDOG  | on-chip    | watchdog                            |
 +-----------+------------+-------------------------------------+
 | HWINFO    | on-chip    | reset cause                         |
 +-----------+------------+-------------------------------------+
 | DMA       | on-chip    | dma                                 |
 +-----------+------------+-------------------------------------+
 | ADC       | on-chip    | adc                                 |
 +-----------+------------+-------------------------------------+
 | GPT       | on-chip    | gpt                                 |
 +-----------+------------+-------------------------------------+
 | USB       | on-chip    | USB                                 |
 +-----------+------------+-------------------------------------+
 | TRNG      | on-chip    | entropy                             |
 +-----------+------------+-------------------------------------+

 The default configuration can be found in the defconfig file:
 ``boards/arm/mimxrt1024_evk/mimxrt1024_evk_defconfig``

 Other hardware features are not currently supported by the port.

 Connections and I/Os
 ====================

 The MIMXRT1024 SoC has five pairs of pinmux/gpio controllers.

 +---------------+-----------------+---------------------------+
 | Name          | Function        | Usage                     |
 +===============+=================+===========================+
 | GPIO_AD_B1_08 | GPIO            | LED                       |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_06 | LPUART1_TX      | UART Console              |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_07 | LPUART1_RX      | UART Console              |
 +---------------+-----------------+---------------------------+
 | WAKEUP        | GPIO            | SW4                       |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_04 | ENET_RST        | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_08 | ENET_REF_CLK    | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_09 | ENET_RX_DATA01  | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_10 | ENET_RX_DATA00/LPSPI1_SCK | Ethernet/SPI    |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_11 | ENET_RX_EN/LPSPI1_PCS0 | Ethernet/SPI       |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_12 | ENET_RX_ER/LPSPI1_SDO | Ethernet/SPI        |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_13 | ENET_TX_EN/LPSPI1_SDI | Ethernet/SPI        |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_14 | ENET_TX_DATA00  | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B0_15 | ENET_TX_DATA01  | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B1_06 | ENET_INT        | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_EMC_41   | ENET_MDC        | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_EMC_40   | ENET_MDIO       | Ethernet                  |
 +---------------+-----------------+---------------------------+
 | GPIO_SD_B1_00 | FLEXCAN1_TX     | CAN TX                    |
 +---------------+-----------------+---------------------------+
 | GPIO_SD_B1_01 | FLEXCAN1_RX     | CAN RX                    |
 +---------------+-----------------+---------------------------+
 | GPIO_SD_B1_02 | LPI2C4_SCL      | I2C SCL                   |
 +---------------+-----------------+---------------------------+
 | GPIO_SD_B1_03 | LPI2C4_SDA      | I2C SDA                   |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B1_11 | ADC1            | ADC1 Channel 11           |
 +---------------+-----------------+---------------------------+
 | GPIO_AD_B1_10 | ADC1            | ADC1 Channel 10           |
 +---------------+-----------------+---------------------------+

 System Clock
 ============

 The MIMXRT1024 SoC is configured to use the 32 KHz low frequency oscillator on
 the board as a source for the GPT timer to generate a system clock.

 Serial Port
 ===========

 The MIMXRT1024 SoC has eight UARTs. One is configured for the console and the
 remaining are not used.

 Programming and Debugging
 *************************

 Build and flash applications as usual (see :ref:`build_an_application` and
 :ref:`application_run` for more details).

 Configuring a Debug Probe
 =========================

 A debug probe is used for both flashing and debugging the board. This board is
 configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`,
 however the :ref:`pyocd-debug-host-tools` do not yet support programming the
 external flashes on this board so you must reconfigure the board for one of the
 following debug probes instead.

 :ref:`jlink-external-debug-probe`
 ---------------------------------

 Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
 path.

 Attach a J-Link 10-pin connector to J55. Check that jumpers J47 and J48 are
 **off** (they are on by default when boards ship from the factory) to ensure
 SWD signals are disconnected from the OpenSDA microcontroller.

 Configuring a Console
 =====================

 Regardless of your choice in debug probe, we will use the OpenSDA
 microcontroller as a usb-to-serial adapter for the serial console. Check that
 jumpers J50 and J46 are **on** (they are on by default when boards ship from
 the factory) to connect UART signals to the OpenSDA microcontroller.

 Connect a USB cable from your PC to J23.

 Use the following settings with your serial terminal of choice (minicom, putty,
 etc.):

 - Speed: 115200
 - Data: 8 bits
 - Parity: None
 - Stop bits: 1

 Flashing
 ========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: mimxrt1024_evk
    :goals: flash

 Open a serial terminal, reset the board (press the SW9 button), and you should
 see the following message in the terminal:

 .. code-block:: console

    ***** Booting Zephyr OS v2.4.0-rc1 *****
    Hello World! mimxrt1024_evk

 Debugging
 =========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: mimxrt1024_evk
    :goals: debug

 Open a serial terminal, step through the application in your debugger, and you
 should see the following message in the terminal:

 .. code-block:: console

    ***** Booting Zephyr OS v2.4.0-rc1 *****
    Hello World! mimxrt1024_evk

 .. _MIMXRT1024-EVK Website:
    https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1024-evaluation-kit:MIMXRT1024-EVK

 .. _MIMXRT1024-EVK User Guide:
    https://www.nxp.com.cn/docs/en/user-guide/MIMXRT1024EVKHUG.pdf

 .. _MIMXRT1024-EVK Design Files:
    https://www.nxp.com/webapp/sps/download/preDownload.jsp?render=true

 .. _i.MX RT1024 Website:
    https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/i-mx-rt-crossover-mcus/i-mx-rt1024-crossover-processor-with-arm-cortex-m7-core:i.MX-RT1024

 .. _i.MX RT1024 Datasheet:
    https://www.nxp.com.cn/docs/en/data-sheet/IMXRT1024CEC.pdf

 .. _i.MX RT1024 Reference Manual:
    https://www.nxp.com.cn/docs/en/reference-manual/IMXRT1024RM.pdf
	.. _mimxrt1024_evk:

	NXP MIMXRT1024-EVK
	##################

	Overview
	********

	The i.MX RT1024 expands the i.MX RT crossover processor families by providing
	high-performance feature set in low-cost LQFP packages, further simplifying
	board design and layout for customers. The i.MX RT1024 runs on the Arm®
	Cortex®-M7 core at 500 MHz.

	.. image:: ./mimxrt1024_evk.jpg
	:width: 720px
	:align: center
	:alt: MIMXRT1024-EVK

	Hardware
	********

	- MIMXRT1024DAG5A MCU (600 MHz, 256 KB on-chip memory, 4096KB on-chip QSPI
	flash)

	- Memory

	- 256 Mbit SDRAM
	- 64 Mbit QSPI Flash
	- TF socket for SD card

	- Connectivity

	- 10/100 Mbit/s Ethernet PHY
	- Micro USB host and OTG connectors
	- CAN transceivers
	- Arduino interface

	- Audio

	- Audio Codec
	- 4-pole audio headphone jack
	- Microphone
	- External speaker connection

	- Power

	- 5 V DC jack

	- Debug

	- JTAG 10-pin connector
	- OpenSDA with DAPLink

	- Sensor

	- 6-axis FXOS8700CQ digital accelerometer and magnetometer

	For more information about the MIMXRT1024 SoC and MIMXRT1024-EVK board, see
	these references:

	- `i.MX RT1024 Website`_
	- `i.MX RT1024 Datasheet`_
	- `i.MX RT1024 Reference Manual`_
	- `MIMXRT1024-EVK Website`_
	- `MIMXRT1024-EVK User Guide`_
	- `MIMXRT1024-EVK Design Files`_

	Supported Features
	==================

	The mimxrt1024_evk board configuration supports the following hardware
	features:

	+-----------+------------+-------------------------------------+
	\| Interface \| Controller \| Driver/Component \|
	+===========+============+=====================================+
	\| NVIC \| on-chip \| nested vector interrupt controller \|
	+-----------+------------+-------------------------------------+
	\| SYSTICK \| on-chip \| systick \|
	+-----------+------------+-------------------------------------+
	\| FLASH \| on-chip \| QSPI flash \|
	+-----------+------------+-------------------------------------+
	\| GPIO \| on-chip \| gpio \|
	+-----------+------------+-------------------------------------+
	\| UART \| on-chip \| serial port-polling; \|
	\| \| \| serial port-interrupt \|
	+-----------+------------+-------------------------------------+
	\| SPI \| on-chip \| spi \|
	+-----------+------------+-------------------------------------+
	\| ENET \| on-chip \| ethernet \|
	+-----------+------------+-------------------------------------+
	\| CAN \| on-chip \| can \|
	+-----------+------------+-------------------------------------+
	\| WATCHDOG \| on-chip \| watchdog \|
	+-----------+------------+-------------------------------------+
	\| HWINFO \| on-chip \| reset cause \|
	+-----------+------------+-------------------------------------+
	\| DMA \| on-chip \| dma \|
	+-----------+------------+-------------------------------------+
	\| ADC \| on-chip \| adc \|
	+-----------+------------+-------------------------------------+
	\| GPT \| on-chip \| gpt \|
	+-----------+------------+-------------------------------------+
	\| USB \| on-chip \| USB \|
	+-----------+------------+-------------------------------------+
	\| TRNG \| on-chip \| entropy \|
	+-----------+------------+-------------------------------------+

	The default configuration can be found in the defconfig file:
	``boards/arm/mimxrt1024_evk/mimxrt1024_evk_defconfig``

	Other hardware features are not currently supported by the port.

	Connections and I/Os
	====================

	The MIMXRT1024 SoC has five pairs of pinmux/gpio controllers.

	+---------------+-----------------+---------------------------+
	\| Name \| Function \| Usage \|
	+===============+=================+===========================+
	\| GPIO_AD_B1_08 \| GPIO \| LED \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_06 \| LPUART1_TX \| UART Console \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_07 \| LPUART1_RX \| UART Console \|
	+---------------+-----------------+---------------------------+
	\| WAKEUP \| GPIO \| SW4 \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_04 \| ENET_RST \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_08 \| ENET_REF_CLK \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_09 \| ENET_RX_DATA01 \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_10 \| ENET_RX_DATA00/LPSPI1_SCK \| Ethernet/SPI \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_11 \| ENET_RX_EN/LPSPI1_PCS0 \| Ethernet/SPI \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_12 \| ENET_RX_ER/LPSPI1_SDO \| Ethernet/SPI \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_13 \| ENET_TX_EN/LPSPI1_SDI \| Ethernet/SPI \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_14 \| ENET_TX_DATA00 \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B0_15 \| ENET_TX_DATA01 \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B1_06 \| ENET_INT \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_EMC_41 \| ENET_MDC \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_EMC_40 \| ENET_MDIO \| Ethernet \|
	+---------------+-----------------+---------------------------+
	\| GPIO_SD_B1_00 \| FLEXCAN1_TX \| CAN TX \|
	+---------------+-----------------+---------------------------+
	\| GPIO_SD_B1_01 \| FLEXCAN1_RX \| CAN RX \|
	+---------------+-----------------+---------------------------+
	\| GPIO_SD_B1_02 \| LPI2C4_SCL \| I2C SCL \|
	+---------------+-----------------+---------------------------+
	\| GPIO_SD_B1_03 \| LPI2C4_SDA \| I2C SDA \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B1_11 \| ADC1 \| ADC1 Channel 11 \|
	+---------------+-----------------+---------------------------+
	\| GPIO_AD_B1_10 \| ADC1 \| ADC1 Channel 10 \|
	+---------------+-----------------+---------------------------+

	System Clock
	============

	The MIMXRT1024 SoC is configured to use the 32 KHz low frequency oscillator on
	the board as a source for the GPT timer to generate a system clock.

	Serial Port
	===========

	The MIMXRT1024 SoC has eight UARTs. One is configured for the console and the
	remaining are not used.

	Programming and Debugging
	*************************

	Build and flash applications as usual (see :ref:`build_an_application` and
	:ref:`application_run` for more details).

	Configuring a Debug Probe
	=========================

	A debug probe is used for both flashing and debugging the board. This board is
	configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`,
	however the :ref:`pyocd-debug-host-tools` do not yet support programming the
	external flashes on this board so you must reconfigure the board for one of the
	following debug probes instead.

	:ref:`jlink-external-debug-probe`
	---------------------------------

	Install the :ref:`jlink-debug-host-tools` and make sure they are in your search
	path.

	Attach a J-Link 10-pin connector to J55. Check that jumpers J47 and J48 are
	off (they are on by default when boards ship from the factory) to ensure
	SWD signals are disconnected from the OpenSDA microcontroller.

	Configuring a Console
	=====================

	Regardless of your choice in debug probe, we will use the OpenSDA
	microcontroller as a usb-to-serial adapter for the serial console. Check that
	jumpers J50 and J46 are on (they are on by default when boards ship from
	the factory) to connect UART signals to the OpenSDA microcontroller.

	Connect a USB cable from your PC to J23.

	Use the following settings with your serial terminal of choice (minicom, putty,
	etc.):

	- Speed: 115200
	- Data: 8 bits
	- Parity: None
	- Stop bits: 1

	Flashing
	========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: mimxrt1024_evk
	:goals: flash

	Open a serial terminal, reset the board (press the SW9 button), and you should
	see the following message in the terminal:

	.. code-block:: console

	*** Booting Zephyr OS v2.4.0-rc1 ***
	Hello World! mimxrt1024_evk

	Debugging
	=========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: mimxrt1024_evk
	:goals: debug

	Open a serial terminal, step through the application in your debugger, and you
	should see the following message in the terminal:

	.. code-block:: console

	*** Booting Zephyr OS v2.4.0-rc1 ***
	Hello World! mimxrt1024_evk

	.. _MIMXRT1024-EVK Website:
	https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1024-evaluation-kit:MIMXRT1024-EVK

	.. _MIMXRT1024-EVK User Guide:
	https://www.nxp.com.cn/docs/en/user-guide/MIMXRT1024EVKHUG.pdf

	.. _MIMXRT1024-EVK Design Files:
	https://www.nxp.com/webapp/sps/download/preDownload.jsp?render=true

	.. _i.MX RT1024 Website:
	https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/i-mx-rt-crossover-mcus/i-mx-rt1024-crossover-processor-with-arm-cortex-m7-core:i.MX-RT1024

	.. _i.MX RT1024 Datasheet:
	https://www.nxp.com.cn/docs/en/data-sheet/IMXRT1024CEC.pdf

	.. _i.MX RT1024 Reference Manual:
	https://www.nxp.com.cn/docs/en/reference-manual/IMXRT1024RM.pdf