| # Nordic Semiconductor nRF5 802.15.4 configuration options |
| |
| # Copyright (c) 2017 Nordic Semiconductor ASA |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| menuconfig IEEE802154_NRF5 |
| bool "nRF52 series IEEE 802.15.4 Driver" |
| default y |
| depends on DT_HAS_NORDIC_NRF_IEEE802154_ENABLED |
| select NRF_802154_RADIO_DRIVER if HAS_HW_NRF_RADIO_IEEE802154 |
| select NRF_802154_SER_HOST if !HAS_HW_NRF_RADIO_IEEE802154 |
| |
| if IEEE802154_NRF5 |
| |
| config IEEE802154_NRF5_RX_STACK_SIZE |
| int "Driver's internal RX thread stack size" |
| default 800 |
| help |
| This option sets the driver's stack size for its internal RX thread. |
| The default value should be sufficient, but in case it proves to be |
| a too little one, this option makes it easy to play with the size. |
| |
| config IEEE802154_NRF5_INIT_PRIO |
| int "nRF52 IEEE 802.15.4 initialization priority" |
| default 80 |
| help |
| Set the initialization priority number. Do not mess with it unless |
| you know what you are doing. |
| |
| config IEEE802154_NRF5_EXT_IRQ_MGMT |
| bool |
| help |
| The driver may manage radio IRQs by itself, or use an external |
| radio IRQ provider. When radio IRQs are managed by an external |
| provider, the driver shall not configure radio IRQs. |
| |
| Enable this option when external radio IRQ provider is enabled in |
| the system. One example of external radio IRQ provider could be |
| a radio arbiter used in dynamic multiprotocol applications. |
| |
| config IEEE802154_NRF5_UICR_EUI64_ENABLE |
| bool "Support usage of EUI64 value stored in UICR registers" |
| depends on !IEEE802154_VENDOR_OUI_ENABLE |
| depends on SOC_SERIES_NRF52X || SOC_SERIES_NRF53X |
| help |
| This option enables setting custom vendor EUI64 value |
| stored in User information configuration registers (UICR). |
| Notice that this disables the default setting of EUI64 |
| value from Factory information configuration registers |
| (FICR). |
| |
| if IEEE802154_NRF5_UICR_EUI64_ENABLE |
| |
| config IEEE802154_NRF5_UICR_EUI64_REG |
| int "UICR base register for the EUI64 value" |
| range 0 30 if SOC_SERIES_NRF52X |
| range 0 190 if SOC_SERIES_NRF53X |
| default 0 |
| help |
| Base of the two consecutive registers from the UICR customer |
| section in which custom EUI64 is stored. |
| |
| endif # IEEE802154_NRF5_UICR_EUI64_ENABLE |
| |
| config IEEE802154_NRF5_FCS_IN_LENGTH |
| bool "Include FCS field in the overall packet length" |
| default y if IEEE802154_RAW_MODE || NET_L2_OPENTHREAD |
| help |
| Some 802.15.4 L2 implementations expect that FCS length is included in |
| the overall packet length while others not. Allow to configure this |
| behavior, based on the selected upper layer. |
| |
| config IEEE802154_NRF5_DELAY_TRX_ACC |
| int "Clock accuracy for delayed operations" |
| default CLOCK_CONTROL_NRF_ACCURACY if CLOCK_CONTROL_NRF_ACCURACY < 255 |
| default 255 |
| help |
| Accuracy of the clock used for scheduling radio delayed operations (delayed transmission |
| or delayed reception), in ppm. |
| |
| config IEEE802154_NRF5_LOG_RX_FAILURES |
| bool "Frame reception failures logging" |
| help |
| There are few cases where the frame reception failure can happen because of |
| internal cause. These cases are reported forward by general code error. |
| |
| This options enables logging the reason of frame reception failure. |
| It can be helpful for the network traffic analyze but it generates also |
| a lot of log records in a stress environment. |
| |
| endif |
