/*
 * Copyright (c) 2021, NXP
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include "mimxrt1160_evk-pinctrl.dtsi"
#include <zephyr/dt-bindings/input/input-event-codes.h>

/ {
	aliases {
		led0 = &green_led;
		sw0 = &user_button;
		magn0 = &fxos8700;
		accel0 = &fxos8700;
		sdhc0 = &usdhc1;
	};

	leds {
		compatible = "gpio-leds";
		green_led: led-1 {
			gpios = <&gpio9 3 GPIO_ACTIVE_LOW>;
			label = "User LED D6";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		user_button: button-1 {
			label = "User SW7";
			gpios = <&gpio13 0 GPIO_ACTIVE_HIGH>;
			zephyr,code = <INPUT_KEY_0>;
		};
	};

	pwmleds {
		compatible = "pwm-leds";

		green_pwm_led: green_pwm_led {
			pwms = <&flexpwm1_pwm2 0 PWM_MSEC(20) PWM_POLARITY_NORMAL>;
		};
	};
};

&lpuart1 {
	status = "okay";
	current-speed = <115200>;
	pinctrl-0 = <&pinmux_lpuart1>;
	pinctrl-1 = <&pinmux_lpuart1_sleep>;
	pinctrl-names = "default", "sleep";
};

&lpuart2 {
	pinctrl-0 = <&pinmux_lpuart2>;
	pinctrl-1 = <&pinmux_lpuart2_sleep>;
	pinctrl-names = "default", "sleep";
};

&user_button {
	status = "okay";
};

&green_led {
	status = "okay";
};

&lpi2c5 {
	status = "okay";
	pinctrl-0 = <&pinmux_lpi2c1>;
	pinctrl-names = "default";

	fxos8700: fxos8700@1f {
		compatible = "nxp,fxos8700";
		reg = <0x1f>;

		/* Two zero ohm resistors (R256 and R270) isolate sensor
		 * interrupt gpios from the soc and are unpopulated by default.
		 * Note that if you populate them, they conflict with camera and
		 * ethernet PHY reset signals.
		 */
		int1-gpios = <&gpio11 14 GPIO_ACTIVE_LOW>;
		int2-gpios = <&gpio11 15 GPIO_ACTIVE_LOW>;
	};
};

&flexspi {
	status = "okay";
	ahb-prefetch;
	ahb-read-addr-opt;
	rx-clock-source = <1>;
	reg = <0x400cc000 0x4000>, <0x30000000 DT_SIZE_M(16)>;
	is25wp128: is25wp128@0 {
		compatible = "nxp,imx-flexspi-nor";
		size = <134217728>;
		reg = <0>;
		spi-max-frequency = <133000000>;
		status = "okay";
		jedec-id = [9d 70 17];
		erase-block-size = <4096>;
		write-block-size = <1>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			boot_partition: partition@0 {
				label = "mcuboot";
				reg = <0x00000000 DT_SIZE_K(128)>;
			};
			/* Note slot 0 has one additional sector,
			 * this is intended for use with the swap move algorithm
			 */
			slot0_partition: partition@20000 {
				label = "image-0";
				reg = <0x00020000 0x301000>;
			};
			slot1_partition: partition@321000 {
				label = "image-1";
				reg = <0x00321000 0x300000>;
			};
			scratch_partition: partition@621000 {
				label = "image-scratch";
				reg = <0x00621000 DT_SIZE_K(128)>;
			};
			storage_partition: partition@641000 {
				label = "storage";
				reg = <0x00641000 DT_SIZE_K(1856)>;
			};
		};
	};
};

&flexpwm1_pwm2 {
	status = "okay";
	pinctrl-0 = <&pinmux_flexpwm1>;
	pinctrl-names = "default";
};

&enet {
	pinctrl-0 = <&pinmux_enet>;
	pinctrl-names = "default";
	ptp {
		pinctrl-0 = <&pinmux_ptp>;
		pinctrl-names = "default";
	};
};

&csi {
	pinctrl-0 = <&pinmux_csi>;
	pinctrl-names = "default";
};

&flexcan3 {
	pinctrl-0 = <&pinmux_flexcan3>;
	pinctrl-names = "default";
};

&lcdif {
	pinctrl-0 = <&pinmux_lcdif>;
	pinctrl-names = "default";
};

&lpi2c1 {
	pinctrl-0 =<&pinmux_lpi2c5>;
	pinctrl-names = "default";
};

&lpspi1 {
	pinctrl-0 = <&pinmux_lpspi1>;
	pinctrl-names = "default";
};

&lpuart2 {
	pinctrl-0 = <&pinmux_lpuart2>;
	pinctrl-1 = <&pinmux_lpuart2_sleep>;
	pinctrl-names = "default", "sleep";
};

&sai1 {
	pinctrl-0 = <&pinmux_sai1>;
	pinctrl-names = "default";
};

&lpadc0 {
	pinctrl-0 = <&pinmux_lpadc0>;
	pinctrl-names = "default";
};

&flexspi {
	pinctrl-0 = <&pinmux_flexspi1>;
	pinctrl-names = "default";
};

&usdhc1 {
	pinctrl-0 = <&pinmux_usdhc1>;
	pinctrl-1 = <&pinmux_usdhc1_dat3_nopull>;
	pinctrl-names = "default", "nopull";
};