/*
 *  Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
 *
 *  Redistribution and use in source and binary forms, with or without
 *  modification, are permitted provided that the following conditions
 *  are met:
 *
 *    Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 *    Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the
 *    distribution.
 *
 *    Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
 *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 */
//*****************************************************************************
//
//  uart.h
//
//  Defines and Macros for the UART.
//
//*****************************************************************************

#ifndef __UART_H__
#define __UART_H__

//*****************************************************************************
//
// If building with a C++ compiler, make all of the definitions in this header
// have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif

//*****************************************************************************
//
// Values that can be passed to UARTIntEnable, UARTIntDisable, and UARTIntClear
// as the ulIntFlags parameter, and returned from UARTIntStatus.
//
//*****************************************************************************
#define UART_INT_DMATX          0x20000     // DMA Tx Done interrupt Mask
#define UART_INT_DMARX          0x10000     // DMA Rx Done interrupt Mask
#define UART_INT_EOT            0x800       // End of transfer interrupt Mask
#define UART_INT_OE             0x400       // Overrun Error Interrupt Mask
#define UART_INT_BE             0x200       // Break Error Interrupt Mask
#define UART_INT_PE             0x100       // Parity Error Interrupt Mask
#define UART_INT_FE             0x080       // Framing Error Interrupt Mask
#define UART_INT_RT             0x040       // Receive Timeout Interrupt Mask
#define UART_INT_TX             0x020       // Transmit Interrupt Mask
#define UART_INT_RX             0x010       // Receive Interrupt Mask
#define UART_INT_CTS            0x002       // CTS Modem Interrupt Mask


//*****************************************************************************
//
// Values that can be passed to UARTConfigSetExpClk as the ulConfig parameter
// and returned by UARTConfigGetExpClk in the pulConfig parameter.
// Additionally, the UART_CONFIG_PAR_* subset can be passed to
// UARTParityModeSet as the ulParity parameter, and are returned by
// UARTParityModeGet.
//
//*****************************************************************************
#define UART_CONFIG_WLEN_MASK   0x00000060  // Mask for extracting word length
#define UART_CONFIG_WLEN_8      0x00000060  // 8 bit data
#define UART_CONFIG_WLEN_7      0x00000040  // 7 bit data
#define UART_CONFIG_WLEN_6      0x00000020  // 6 bit data
#define UART_CONFIG_WLEN_5      0x00000000  // 5 bit data
#define UART_CONFIG_STOP_MASK   0x00000008  // Mask for extracting stop bits
#define UART_CONFIG_STOP_ONE    0x00000000  // One stop bit
#define UART_CONFIG_STOP_TWO    0x00000008  // Two stop bits
#define UART_CONFIG_PAR_MASK    0x00000086  // Mask for extracting parity
#define UART_CONFIG_PAR_NONE    0x00000000  // No parity
#define UART_CONFIG_PAR_EVEN    0x00000006  // Even parity
#define UART_CONFIG_PAR_ODD     0x00000002  // Odd parity
#define UART_CONFIG_PAR_ONE     0x00000082  // Parity bit is one
#define UART_CONFIG_PAR_ZERO    0x00000086  // Parity bit is zero

//*****************************************************************************
//
// Values that can be passed to UARTFIFOLevelSet as the ulTxLevel parameter and
// returned by UARTFIFOLevelGet in the pulTxLevel.
//
//*****************************************************************************
#define UART_FIFO_TX1_8         0x00000000  // Transmit interrupt at 1/8 Full
#define UART_FIFO_TX2_8         0x00000001  // Transmit interrupt at 1/4 Full
#define UART_FIFO_TX4_8         0x00000002  // Transmit interrupt at 1/2 Full
#define UART_FIFO_TX6_8         0x00000003  // Transmit interrupt at 3/4 Full
#define UART_FIFO_TX7_8         0x00000004  // Transmit interrupt at 7/8 Full

//*****************************************************************************
//
// Values that can be passed to UARTFIFOLevelSet as the ulRxLevel parameter and
// returned by UARTFIFOLevelGet in the pulRxLevel.
//
//*****************************************************************************
#define UART_FIFO_RX1_8         0x00000000  // Receive interrupt at 1/8 Full
#define UART_FIFO_RX2_8         0x00000008  // Receive interrupt at 1/4 Full
#define UART_FIFO_RX4_8         0x00000010  // Receive interrupt at 1/2 Full
#define UART_FIFO_RX6_8         0x00000018  // Receive interrupt at 3/4 Full
#define UART_FIFO_RX7_8         0x00000020  // Receive interrupt at 7/8 Full

//*****************************************************************************
//
// Values that can be passed to UARTDMAEnable() and UARTDMADisable().
//
//*****************************************************************************
#define UART_DMA_ERR_RXSTOP     0x00000004  // Stop DMA receive if UART error
#define UART_DMA_TX             0x00000002  // Enable DMA for transmit
#define UART_DMA_RX             0x00000001  // Enable DMA for receive

//*****************************************************************************
//
// Values returned from UARTRxErrorGet().
//
//*****************************************************************************
#define UART_RXERROR_OVERRUN    0x00000008
#define UART_RXERROR_BREAK      0x00000004
#define UART_RXERROR_PARITY     0x00000002
#define UART_RXERROR_FRAMING    0x00000001

//*****************************************************************************
//
// Values that can be passed to UARTModemControlSet()and UARTModemControlClear()
// or returned from UARTModemControlGet().
//
//*****************************************************************************
#define UART_OUTPUT_RTS         0x00000800

//*****************************************************************************
//
// Values that can be returned from UARTModemStatusGet().
//
//*****************************************************************************
#define UART_INPUT_CTS          0x00000001

//*****************************************************************************
//
// Values that can be passed to UARTFlowControl() or returned from
// UARTFlowControlGet().
//
//*****************************************************************************
#define UART_FLOWCONTROL_TX     0x00008000
#define UART_FLOWCONTROL_RX     0x00004000
#define UART_FLOWCONTROL_NONE   0x00000000

//*****************************************************************************
//
// Values that can be passed to UARTTxIntModeSet() or returned from
// UARTTxIntModeGet().
//
//*****************************************************************************
#define UART_TXINT_MODE_FIFO    0x00000000
#define UART_TXINT_MODE_EOT     0x00000010


//*****************************************************************************
//
// API Function prototypes
//
//*****************************************************************************
extern void UARTParityModeSet(unsigned long ulBase, unsigned long ulParity);
extern unsigned long UARTParityModeGet(unsigned long ulBase);
extern void UARTFIFOLevelSet(unsigned long ulBase, unsigned long ulTxLevel,
                             unsigned long ulRxLevel);
extern void UARTFIFOLevelGet(unsigned long ulBase, unsigned long *pulTxLevel,
                             unsigned long *pulRxLevel);
extern void UARTConfigSetExpClk(unsigned long ulBase, unsigned long ulUARTClk,
                                unsigned long ulBaud, unsigned long ulConfig);
extern void UARTConfigGetExpClk(unsigned long ulBase, unsigned long ulUARTClk,
                                unsigned long *pulBaud,
                                unsigned long *pulConfig);
extern void UARTEnable(unsigned long ulBase);
extern void UARTDisable(unsigned long ulBase);
extern void UARTFIFOEnable(unsigned long ulBase);
extern void UARTFIFODisable(unsigned long ulBase);
extern tBoolean UARTCharsAvail(unsigned long ulBase);
extern tBoolean UARTSpaceAvail(unsigned long ulBase);
extern long UARTCharGetNonBlocking(unsigned long ulBase);
extern long UARTCharGet(unsigned long ulBase);
extern tBoolean UARTCharPutNonBlocking(unsigned long ulBase,
                                       unsigned char ucData);
extern void UARTCharPut(unsigned long ulBase, unsigned char ucData);
extern void UARTBreakCtl(unsigned long ulBase, tBoolean bBreakState);
extern tBoolean UARTBusy(unsigned long ulBase);
extern void UARTIntRegister(unsigned long ulBase, void(*pfnHandler)(void));
extern void UARTIntUnregister(unsigned long ulBase);
extern void UARTIntEnable(unsigned long ulBase, unsigned long ulIntFlags);
extern void UARTIntDisable(unsigned long ulBase, unsigned long ulIntFlags);
extern unsigned long UARTIntStatus(unsigned long ulBase, tBoolean bMasked);
extern void UARTIntClear(unsigned long ulBase, unsigned long ulIntFlags);
extern void UARTDMAEnable(unsigned long ulBase, unsigned long ulDMAFlags);
extern void UARTDMADisable(unsigned long ulBase, unsigned long ulDMAFlags);
extern unsigned long UARTRxErrorGet(unsigned long ulBase);
extern void UARTRxErrorClear(unsigned long ulBase);
extern void UARTModemControlSet(unsigned long ulBase,
                                unsigned long ulControl);
extern void UARTModemControlClear(unsigned long ulBase,
                                  unsigned long ulControl);
extern unsigned long UARTModemControlGet(unsigned long ulBase);
extern unsigned long UARTModemStatusGet(unsigned long ulBase);
extern void UARTFlowControlSet(unsigned long ulBase, unsigned long ulMode);
extern unsigned long UARTFlowControlGet(unsigned long ulBase);
extern void UARTTxIntModeSet(unsigned long ulBase, unsigned long ulMode);
extern unsigned long UARTTxIntModeGet(unsigned long ulBase);

//*****************************************************************************
//
// Mark the end of the C bindings section for C++ compilers.
//
//*****************************************************************************
#ifdef __cplusplus
}
#endif

#endif //  __UART_H__