# Copyright (c) 2022 NXP
# SPDX-License-Identifier: Apache-2.0

description: |
  The node has the 'pinctrl' node label set in MCUX SoC's devicetree. These
  nodes can be autogenerated using the MCUXpresso config tools combined with
  the imx_dts_gen.py script in NXP's HAL. The mux, mode, input, daisy, and cfg
  fields in a group select the pins to be configured, and the remaining
  devicetree properties set configuration values for those pins
  for example, here is an group configuring LPUART1 pins:

  group0 {
    pinmux = <&iomuxc_uart2_rxd_uart_rx_uart2_rx,
      &iomuxc_uart2_txd_uart_tx_uart2_tx>;
      bias-pull-up;
      slew-rate = "slow";
      drive-strength = "x1";
  };

  This will select UART2_RXD as UART2 rx, and UART2_TXD as UART2 tx.
  Both pins will be configured with a slow slew rate, and x1 drive
  strength.
  Note that the soc level iomuxc dts file can be examined to find the possible
  pinmux options. Here are the affects of each property on the
  IOMUXC SW_PAD_CTL register:
  input-schmitt-enable: HYS=1
  drive-open-drain: OD=1
  bias-pull-down: PD=0
  bias-pull-up: PU
  slew-rate: FSEL1=<enum_idx>
  drive-strength: DSE=<enum_idx>
  input-enable: SION=1 (in SW_MUX_CTL_PAD register)

  If only required properties are supplied, the pin will have the following
  configuration:
  HYS=0,
  PD=0
  PU=0
  OD=0,
  FSEL1=<slew-rate>,
  DSE=<drive-strength>,
  SION=0,


compatible: "nxp,imx93-pinctrl"

include: base.yaml

child-binding:
  description: iMX pin controller pin group
  child-binding:
    description: |
      iMX pin controller pin configuration node.

    include:
      - name: pincfg-node.yaml
        property-allowlist:
          - input-schmitt-enable
          - drive-open-drain
          - input-enable
          - bias-pull-up
          - bias-pull-down

    properties:
      pinmux:
        required: true
        type: phandles
        description: |
          Pin mux selections for this group. See the soc level iomuxc DTSI file
          for a defined list of these options.
      drive-strength:
        required: true
        type: string
        enum:
          - "x0"
          - "x1"
          - "x2"
          - "x3"
          - "x4"
          - "x5"
          - "x6"
        description: |
          Pin output drive strength. Sets the DSE field in the IOMUXC peripheral.
          00_0000 X0, No driver
          00_0001 X1
          00_0011 X2
          00_0111 X3
          00_1111 X4
          01_1111 X5
          11_1111 X6
      slew-rate:
        required: true
        type: string
        enum:
          - "slow"
          - "slightly_slow"
          - "slightly_fast"
          - "fast"
        description: |
          Select slew rate for pin. Corresponds to SRE field in IOMUXC peripheral
          0 SLOW — Slow Frequency Slew Rate
          1 Slightly SLOW — Slightly Slow Frequency Slew Rate
          2 Slightly FAST — Slightly Fast Frequency Slew Rate
          3 FAST — Fast Frequency Slew Rate