/*
 * Copyright (c) 2021 Antmicro <www.antmicro.com>
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#define DT_DRV_COMPAT ovti_ov2640
#include <zephyr/kernel.h>
#include <zephyr/device.h>

#include <zephyr/drivers/video.h>
#include <zephyr/drivers/i2c.h>
#include <zephyr/drivers/gpio.h>

#define LOG_LEVEL CONFIG_LOG_DEFAULT_LEVEL
#include <zephyr/logging/log.h>
LOG_MODULE_REGISTER(ov2640);

/* DSP register bank FF=0x00*/
#define QS                  0x44
#define HSIZE               0x51
#define VSIZE               0x52
#define XOFFL               0x53
#define YOFFL               0x54
#define VHYX                0x55
#define TEST                0x57
#define ZMOW                0x5A
#define ZMOH                0x5B
#define ZMHH                0x5C
#define BPADDR              0x7C
#define BPDATA              0x7D
#define SIZEL               0x8C
#define HSIZE8              0xC0
#define VSIZE8              0xC1
#define CTRL1               0xC3

#define CTRLI               0x50
#define CTRLI_LP_DP         0x80

#define CTRL0               0xC2
#define CTRL0_YUV422        0x08
#define CTRL0_YUV_EN        0x04
#define CTRL0_RGB_EN        0x02

#define CTRL2               0x86
#define CTRL2_DCW_EN        0x20
#define CTRL2_SDE_EN        0x10
#define CTRL2_UV_ADJ_EN     0x08
#define CTRL2_UV_AVG_EN     0x04
#define CTRL2_CMX_EN        0x01

#define CTRL3               0x87
#define CTRL3_BPC_EN        0x80
#define CTRL3_WPC_EN        0x40
#define R_DVP_SP            0xD3
#define R_DVP_SP_AUTO_MODE  0x80

#define R_BYPASS                0x05
#define R_BYPASS_DSP_EN         0x00
#define R_BYPASS_DSP_BYPAS      0x01

#define IMAGE_MODE              0xDA
#define IMAGE_MODE_JPEG_EN      0x10
#define IMAGE_MODE_RGB565       0x08

#define RESET                   0xE0
#define RESET_JPEG              0x10
#define RESET_DVP               0x04

#define MC_BIST                 0xF9
#define MC_BIST_RESET           0x80
#define MC_BIST_BOOT_ROM_SEL    0x40

#define BANK_SEL                0xFF
#define BANK_SEL_DSP            0x00
#define BANK_SEL_SENSOR         0x01

/* Sensor register bank FF=0x01*/
#define COM1                0x03
#define REG_PID             0x0A
#define REG_PID_VAL         0x26
#define REG_VER             0x0B
#define REG_VER_VAL         0x42
#define AEC                 0x10
#define CLKRC               0x11
#define COM10               0x15
#define HSTART              0x17
#define HSTOP               0x18
#define VSTART              0x19
#define VSTOP               0x1A
#define AEW                 0x24
#define AEB                 0x25
#define ARCOM2              0x34
#define FLL                 0x46
#define FLH                 0x47
#define COM19               0x48
#define ZOOMS               0x49
#define BD50                0x4F
#define BD60                0x50
#define REG5D               0x5D
#define REG5E               0x5E
#define REG5F               0x5F
#define REG60               0x60
#define HISTO_LOW           0x61
#define HISTO_HIGH          0x62

#define REG04               0x04
#define REG04_DEFAULT       0x28
#define REG04_HFLIP_IMG     0x80
#define REG04_VFLIP_IMG     0x40
#define REG04_HREF_EN       0x08
#define REG04_SET(x)        (REG04_DEFAULT | x)

#define COM2                0x09
#define COM2_OUT_DRIVE_3x   0x02

#define COM3                0x0C
#define COM3_DEFAULT        0x38
#define COM3_BAND_AUTO      0x02
#define COM3_BAND_SET(x)    (COM3_DEFAULT | x)

#define COM7                0x12
#define COM7_SRST           0x80
#define COM7_RES_UXGA       0x00 /* UXGA */
#define COM7_ZOOM_EN        0x04 /* Enable Zoom */
#define COM7_COLOR_BAR      0x02 /* Enable Color Bar Test */

#define COM8                0x13
#define COM8_DEFAULT        0xC0
#define COM8_BNDF_EN        0x20 /* Enable Banding filter */
#define COM8_AGC_EN         0x04 /* AGC Auto/Manual control selection */
#define COM8_AEC_EN         0x01 /* Auto/Manual Exposure control */
#define COM8_SET(x)         (COM8_DEFAULT | x)

#define COM9                0x14 /* AGC gain ceiling */
#define COM9_DEFAULT        0x08
#define COM9_AGC_GAIN_8x    0x02 /* AGC:    8x */
#define COM9_AGC_SET(x)     (COM9_DEFAULT | (x << 5))

#define COM10               0x15

#define CTRL1_AWB           0x08 /* Enable AWB */

#define VV                  0x26
#define VV_AGC_TH_SET(h, l) ((h << 4) | (l & 0x0F))

#define REG32               0x32
#define REG32_UXGA          0x36

/* Configuration arrays */
#define SVGA_HSIZE     (800)
#define SVGA_VSIZE     (600)

#define UXGA_HSIZE     (1600)
#define UXGA_VSIZE     (1200)

struct ov2640_reg {
	uint8_t addr;
	uint8_t value;
};

static const struct ov2640_reg default_regs[] = {
	{ BANK_SEL, BANK_SEL_DSP },
	{ 0x2c,     0xff },
	{ 0x2e,     0xdf },
	{ BANK_SEL, BANK_SEL_SENSOR },
	{ 0x3c,     0x32 },
	{ CLKRC,    0x80 }, /* Set PCLK divider */
	{ COM2,     COM2_OUT_DRIVE_3x }, /* Output drive x2 */
	{ REG04,    REG04_SET(REG04_HREF_EN)},
	{ COM8,     COM8_SET(COM8_BNDF_EN | COM8_AGC_EN | COM8_AEC_EN) },
	{ COM9,     COM9_AGC_SET(COM9_AGC_GAIN_8x)},
	{ COM10,    0x00 }, /* Invert VSYNC */
	{ 0x2c,     0x0c },
	{ 0x33,     0x78 },
	{ 0x3a,     0x33 },
	{ 0x3b,     0xfb },
	{ 0x3e,     0x00 },
	{ 0x43,     0x11 },
	{ 0x16,     0x10 },
	{ 0x39,     0x02 },
	{ 0x35,     0x88 },
	{ 0x22,     0x0a },
	{ 0x37,     0x40 },
	{ 0x23,     0x00 },
	{ ARCOM2,   0xa0 },
	{ 0x06,     0x02 },
	{ 0x06,     0x88 },
	{ 0x07,     0xc0 },
	{ 0x0d,     0xb7 },
	{ 0x0e,     0x01 },
	{ 0x4c,     0x00 },
	{ 0x4a,     0x81 },
	{ 0x21,     0x99 },
	{ AEW,      0x40 },
	{ AEB,      0x38 },
	/* AGC/AEC fast mode operating region */
	{ VV,       VV_AGC_TH_SET(0x08, 0x02) },
	{ COM19,    0x00 }, /* Zoom control 2 LSBs */
	{ ZOOMS,    0x00 }, /* Zoom control 8 MSBs */
	{ 0x5c,     0x00 },
	{ 0x63,     0x00 },
	{ FLL,      0x00 },
	{ FLH,      0x00 },

	/* Set banding filter */
	{ COM3,     COM3_BAND_SET(COM3_BAND_AUTO) },
	{ REG5D,    0x55 },
	{ REG5E,    0x7d },
	{ REG5F,    0x7d },
	{ REG60,    0x55 },
	{ HISTO_LOW,   0x70 },
	{ HISTO_HIGH,  0x80 },
	{ 0x7c,     0x05 },
	{ 0x20,     0x80 },
	{ 0x28,     0x30 },
	{ 0x6c,     0x00 },
	{ 0x6d,     0x80 },
	{ 0x6e,     0x00 },
	{ 0x70,     0x02 },
	{ 0x71,     0x94 },
	{ 0x73,     0xc1 },
	{ 0x3d,     0x34 },
	/* { COM7,   COM7_RES_UXGA | COM7_ZOOM_EN }, */
	{ 0x5a,     0x57 },
	{ BD50,     0xbb },
	{ BD60,     0x9c },

	{ BANK_SEL, BANK_SEL_DSP },
	{ 0xe5,     0x7f },
	{ MC_BIST,  MC_BIST_RESET | MC_BIST_BOOT_ROM_SEL },
	{ 0x41,     0x24 },
	{ RESET,    RESET_JPEG | RESET_DVP },
	{ 0x76,     0xff },
	{ 0x33,     0xa0 },
	{ 0x42,     0x20 },
	{ 0x43,     0x18 },
	{ 0x4c,     0x00 },
	{ CTRL3,    CTRL3_BPC_EN | CTRL3_WPC_EN | 0x10 },
	{ 0x88,     0x3f },
	{ 0xd7,     0x03 },
	{ 0xd9,     0x10 },
	{ R_DVP_SP, R_DVP_SP_AUTO_MODE | 0x2 },
	{ 0xc8,     0x08 },
	{ 0xc9,     0x80 },
	{ BPADDR,   0x00 },
	{ BPDATA,   0x00 },
	{ BPADDR,   0x03 },
	{ BPDATA,   0x48 },
	{ BPDATA,   0x48 },
	{ BPADDR,   0x08 },
	{ BPDATA,   0x20 },
	{ BPDATA,   0x10 },
	{ BPDATA,   0x0e },
	{ 0x90,     0x00 },
	{ 0x91,     0x0e },
	{ 0x91,     0x1a },
	{ 0x91,     0x31 },
	{ 0x91,     0x5a },
	{ 0x91,     0x69 },
	{ 0x91,     0x75 },
	{ 0x91,     0x7e },
	{ 0x91,     0x88 },
	{ 0x91,     0x8f },
	{ 0x91,     0x96 },
	{ 0x91,     0xa3 },
	{ 0x91,     0xaf },
	{ 0x91,     0xc4 },
	{ 0x91,     0xd7 },
	{ 0x91,     0xe8 },
	{ 0x91,     0x20 },
	{ 0x92,     0x00 },
	{ 0x93,     0x06 },
	{ 0x93,     0xe3 },
	{ 0x93,     0x03 },
	{ 0x93,     0x03 },
	{ 0x93,     0x00 },
	{ 0x93,     0x02 },
	{ 0x93,     0x00 },
	{ 0x93,     0x00 },
	{ 0x93,     0x00 },
	{ 0x93,     0x00 },
	{ 0x93,     0x00 },
	{ 0x93,     0x00 },
	{ 0x93,     0x00 },
	{ 0x96,     0x00 },
	{ 0x97,     0x08 },
	{ 0x97,     0x19 },
	{ 0x97,     0x02 },
	{ 0x97,     0x0c },
	{ 0x97,     0x24 },
	{ 0x97,     0x30 },
	{ 0x97,     0x28 },
	{ 0x97,     0x26 },
	{ 0x97,     0x02 },
	{ 0x97,     0x98 },
	{ 0x97,     0x80 },
	{ 0x97,     0x00 },
	{ 0x97,     0x00 },
	{ 0xa4,     0x00 },
	{ 0xa8,     0x00 },
	{ 0xc5,     0x11 },
	{ 0xc6,     0x51 },
	{ 0xbf,     0x80 },
	{ 0xc7,     0x10 },
	{ 0xb6,     0x66 },
	{ 0xb8,     0xA5 },
	{ 0xb7,     0x64 },
	{ 0xb9,     0x7C },
	{ 0xb3,     0xaf },
	{ 0xb4,     0x97 },
	{ 0xb5,     0xFF },
	{ 0xb0,     0xC5 },
	{ 0xb1,     0x94 },
	{ 0xb2,     0x0f },
	{ 0xc4,     0x5c },
	{ 0xa6,     0x00 },
	{ 0xa7,     0x20 },
	{ 0xa7,     0xd8 },
	{ 0xa7,     0x1b },
	{ 0xa7,     0x31 },
	{ 0xa7,     0x00 },
	{ 0xa7,     0x18 },
	{ 0xa7,     0x20 },
	{ 0xa7,     0xd8 },
	{ 0xa7,     0x19 },
	{ 0xa7,     0x31 },
	{ 0xa7,     0x00 },
	{ 0xa7,     0x18 },
	{ 0xa7,     0x20 },
	{ 0xa7,     0xd8 },
	{ 0xa7,     0x19 },
	{ 0xa7,     0x31 },
	{ 0xa7,     0x00 },
	{ 0xa7,     0x18 },
	{ 0x7f,     0x00 },
	{ 0xe5,     0x1f },
	{ 0xe1,     0x77 },
	{ 0xdd,     0x7f },
	{ CTRL0,    CTRL0_YUV422 | CTRL0_YUV_EN | CTRL0_RGB_EN },
	{ 0x00,     0x00 }
};

static const struct ov2640_reg uxga_regs[] = {
	{ BANK_SEL, BANK_SEL_SENSOR },
	/* DSP input image resolution and window size control */
	{ COM7,    COM7_RES_UXGA},
	{ COM1,    0x0F }, /* UXGA=0x0F, SVGA=0x0A, CIF=0x06 */
	{ REG32,   REG32_UXGA }, /* UXGA=0x36, SVGA/CIF=0x09 */

	{ HSTART,  0x11 }, /* UXGA=0x11, SVGA/CIF=0x11 */
	{ HSTOP,   0x75 }, /* UXGA=0x75, SVGA/CIF=0x43 */

	{ VSTART,  0x01 }, /* UXGA=0x01, SVGA/CIF=0x00 */
	{ VSTOP,   0x97 }, /* UXGA=0x97, SVGA/CIF=0x4b */
	{ 0x3d,    0x34 }, /* UXGA=0x34, SVGA/CIF=0x38 */

	{ 0x35,    0x88 },
	{ 0x22,    0x0a },
	{ 0x37,    0x40 },
	{ 0x34,    0xa0 },
	{ 0x06,    0x02 },
	{ 0x0d,    0xb7 },
	{ 0x0e,    0x01 },
	{ 0x42,    0x83 },

	/*
	 * Set DSP input image size and offset.
	 * The sensor output image can be scaled with OUTW/OUTH
	 */
	{ BANK_SEL, BANK_SEL_DSP },
	{ R_BYPASS, R_BYPASS_DSP_BYPAS },

	{ RESET,   RESET_DVP },
	{ HSIZE8,  (UXGA_HSIZE>>3)}, /* Image Horizontal Size HSIZE[10:3] */
	{ VSIZE8,  (UXGA_VSIZE>>3)}, /* Image Vertical Size VSIZE[10:3] */

	/* {HSIZE[11], HSIZE[2:0], VSIZE[2:0]} */
	{ SIZEL,   ((UXGA_HSIZE>>6)&0x40) | ((UXGA_HSIZE&0x7)<<3) | (UXGA_VSIZE&0x7)},

	{ XOFFL,   0x00 }, /* OFFSET_X[7:0] */
	{ YOFFL,   0x00 }, /* OFFSET_Y[7:0] */
	{ HSIZE,   ((UXGA_HSIZE>>2)&0xFF) }, /* H_SIZE[7:0] real/4 */
	{ VSIZE,   ((UXGA_VSIZE>>2)&0xFF) }, /* V_SIZE[7:0] real/4 */

	/* V_SIZE[8]/OFFSET_Y[10:8]/H_SIZE[8]/OFFSET_X[10:8] */
	{ VHYX,    ((UXGA_VSIZE>>3)&0x80) | ((UXGA_HSIZE>>7)&0x08) },
	{ TEST,    (UXGA_HSIZE>>4)&0x80}, /* H_SIZE[9] */

	{ CTRL2,   CTRL2_DCW_EN | CTRL2_SDE_EN |
		CTRL2_UV_AVG_EN | CTRL2_CMX_EN | CTRL2_UV_ADJ_EN },

	/* H_DIVIDER/V_DIVIDER */
	{ CTRLI,   CTRLI_LP_DP | 0x00},
	/* DVP prescaler */
	{ R_DVP_SP, R_DVP_SP_AUTO_MODE | 0x04},

	{ R_BYPASS, R_BYPASS_DSP_EN },
	{ RESET,    0x00 },
	{0, 0},
};

#define NUM_BRIGHTNESS_LEVELS (5)
static const uint8_t brightness_regs[NUM_BRIGHTNESS_LEVELS + 1][5] = {
	{ BPADDR, BPDATA, BPADDR, BPDATA, BPDATA },
	{ 0x00, 0x04, 0x09, 0x00, 0x00 }, /* -2 */
	{ 0x00, 0x04, 0x09, 0x10, 0x00 }, /* -1 */
	{ 0x00, 0x04, 0x09, 0x20, 0x00 }, /*  0 */
	{ 0x00, 0x04, 0x09, 0x30, 0x00 }, /* +1 */
	{ 0x00, 0x04, 0x09, 0x40, 0x00 }, /* +2 */
};

#define NUM_CONTRAST_LEVELS (5)
static const uint8_t contrast_regs[NUM_CONTRAST_LEVELS + 1][7] = {
	{ BPADDR, BPDATA, BPADDR, BPDATA, BPDATA, BPDATA, BPDATA },
	{ 0x00, 0x04, 0x07, 0x20, 0x18, 0x34, 0x06 }, /* -2 */
	{ 0x00, 0x04, 0x07, 0x20, 0x1c, 0x2a, 0x06 }, /* -1 */
	{ 0x00, 0x04, 0x07, 0x20, 0x20, 0x20, 0x06 }, /*  0 */
	{ 0x00, 0x04, 0x07, 0x20, 0x24, 0x16, 0x06 }, /* +1 */
	{ 0x00, 0x04, 0x07, 0x20, 0x28, 0x0c, 0x06 }, /* +2 */
};

#define NUM_SATURATION_LEVELS (5)
static const uint8_t saturation_regs[NUM_SATURATION_LEVELS + 1][5] = {
	{ BPADDR, BPDATA, BPADDR, BPDATA, BPDATA },
	{ 0x00, 0x02, 0x03, 0x28, 0x28 }, /* -2 */
	{ 0x00, 0x02, 0x03, 0x38, 0x38 }, /* -1 */
	{ 0x00, 0x02, 0x03, 0x48, 0x48 }, /*  0 */
	{ 0x00, 0x02, 0x03, 0x58, 0x58 }, /* +1 */
	{ 0x00, 0x02, 0x03, 0x58, 0x58 }, /* +2 */
};

struct ov2640_config {
	struct i2c_dt_spec i2c;
#if DT_INST_NODE_HAS_PROP(0, reset_gpios)
	struct gpio_dt_spec reset_gpio;
#endif
};

struct ov2640_data {
	struct video_format fmt;
};

#define OV2640_VIDEO_FORMAT_CAP(width, height, format) \
	{ \
		.pixelformat = (format), \
		.width_min = (width), \
		.width_max = (width), \
		.height_min = (height), \
		.height_max = (height), \
		.width_step = 0, \
		.height_step = 0 \
	}

static const struct video_format_cap fmts[] = {
	OV2640_VIDEO_FORMAT_CAP(160, 120, VIDEO_PIX_FMT_RGB565),   /* QQVGA */
	OV2640_VIDEO_FORMAT_CAP(176, 144, VIDEO_PIX_FMT_RGB565),   /* QCIF  */
	OV2640_VIDEO_FORMAT_CAP(240, 160, VIDEO_PIX_FMT_RGB565),   /* HQVGA */
	OV2640_VIDEO_FORMAT_CAP(320, 240, VIDEO_PIX_FMT_RGB565),   /* QVGA  */
	OV2640_VIDEO_FORMAT_CAP(352, 288, VIDEO_PIX_FMT_RGB565),   /* CIF   */
	OV2640_VIDEO_FORMAT_CAP(640, 480, VIDEO_PIX_FMT_RGB565),   /* VGA   */
	OV2640_VIDEO_FORMAT_CAP(800, 600, VIDEO_PIX_FMT_RGB565),   /* SVGA  */
	OV2640_VIDEO_FORMAT_CAP(1024, 768, VIDEO_PIX_FMT_RGB565),  /* XVGA  */
	OV2640_VIDEO_FORMAT_CAP(1280, 1024, VIDEO_PIX_FMT_RGB565), /* SXGA  */
	OV2640_VIDEO_FORMAT_CAP(1600, 1200, VIDEO_PIX_FMT_RGB565), /* UXGA  */
	OV2640_VIDEO_FORMAT_CAP(160, 120, VIDEO_PIX_FMT_JPEG),     /* QQVGA */
	OV2640_VIDEO_FORMAT_CAP(176, 144, VIDEO_PIX_FMT_JPEG),     /* QCIF  */
	OV2640_VIDEO_FORMAT_CAP(240, 160, VIDEO_PIX_FMT_JPEG),     /* HQVGA */
	OV2640_VIDEO_FORMAT_CAP(320, 240, VIDEO_PIX_FMT_JPEG),     /* QVGA  */
	OV2640_VIDEO_FORMAT_CAP(352, 288, VIDEO_PIX_FMT_JPEG),     /* CIF   */
	OV2640_VIDEO_FORMAT_CAP(640, 480, VIDEO_PIX_FMT_JPEG),     /* VGA   */
	OV2640_VIDEO_FORMAT_CAP(800, 600, VIDEO_PIX_FMT_JPEG),     /* SVGA  */
	OV2640_VIDEO_FORMAT_CAP(1024, 768, VIDEO_PIX_FMT_JPEG),    /* XVGA  */
	OV2640_VIDEO_FORMAT_CAP(1280, 1024, VIDEO_PIX_FMT_JPEG),   /* SXGA  */
	OV2640_VIDEO_FORMAT_CAP(1600, 1200, VIDEO_PIX_FMT_JPEG),   /* UXGA  */
	{ 0 }
};

static int ov2640_write_reg(const struct i2c_dt_spec *spec, uint8_t reg_addr,
				uint8_t value)
{
	uint8_t tries = 3;

	/**
	 * It rarely happens that the camera does not respond with ACK signal.
	 * In that case it usually responds on 2nd try but there is a 3rd one
	 * just to be sure that the connection error is not caused by driver
	 * itself.
	 */
	while (tries--) {
		if (!i2c_reg_write_byte_dt(spec, reg_addr, value)) {
			return 0;
		}
		/* If writing failed wait 5ms before next attempt */
		k_msleep(5);
	}
	LOG_ERR("failed to write 0x%x to 0x%x", value, reg_addr);

	return -1;
}

static int ov2640_read_reg(const struct i2c_dt_spec *spec, uint8_t reg_addr)
{
	uint8_t tries = 3;
	uint8_t value;

	/**
	 * It rarely happens that the camera does not respond with ACK signal.
	 * In that case it usually responds on 2nd try but there is a 3rd one
	 * just to be sure that the connection error is not caused by driver
	 * itself.
	 */
	while (tries--) {
		if (!i2c_reg_read_byte_dt(spec, reg_addr, &value)) {
			return value;
		}
		/* If reading failed wait 5ms before next attempt */
		k_msleep(5);
	}
	LOG_ERR("failed to read 0x%x register", reg_addr);

	return -1;
}

static int ov2640_write_all(const struct device *dev,
				const struct ov2640_reg *regs, uint16_t reg_num)
{
	uint16_t i = 0;
	const struct ov2640_config *cfg = dev->config;

	for (i = 0; i < reg_num; i++) {
		int err;

		err = ov2640_write_reg(&cfg->i2c, regs[i].addr, regs[i].value);
		if (err) {
			return err;
		}
	}

	return 0;
}

static int ov2640_soft_reset(const struct device *dev)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	/* Switch to DSP register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Initiate system reset */
	ret |= ov2640_write_reg(&cfg->i2c, COM7, COM7_SRST);

	return ret;
}

static int ov2640_set_level(const struct device *dev, int level,
				int max_level, int cols, const uint8_t regs[][cols])
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	level += (max_level / 2 + 1);
	if (level < 0 || level > max_level) {
		return -ENOTSUP;
	}

	/* Switch to DSP register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_DSP);

	for (int i = 0; i < (ARRAY_SIZE(regs[0]) / sizeof(regs[0][0])); i++)	{
		ret |= ov2640_write_reg(&cfg->i2c, regs[0][i], regs[level][i]);
	}

	return ret;
}

static int ov2640_set_brightness(const struct device *dev, int level)
{
	int ret = 0;

	ret = ov2640_set_level(dev, level, NUM_BRIGHTNESS_LEVELS,
			ARRAY_SIZE(brightness_regs[0]), brightness_regs);

	if (ret == -ENOTSUP) {
		LOG_ERR("Brightness level %d not supported", level);
	}

	return ret;
}

static int ov2640_set_saturation(const struct device *dev, int level)
{
	int ret = 0;

	ret = ov2640_set_level(dev, level, NUM_SATURATION_LEVELS,
			ARRAY_SIZE(saturation_regs[0]), saturation_regs);

	if (ret == -ENOTSUP) {
		LOG_ERR("Saturation level %d not supported", level);
	}

	return ret;
}

static int ov2640_set_contrast(const struct device *dev, int level)
{
	int ret = 0;

	ret = ov2640_set_level(dev, level, NUM_CONTRAST_LEVELS,
			ARRAY_SIZE(contrast_regs[0]), contrast_regs);

	if (ret == -ENOTSUP) {
		LOG_ERR("Contrast level %d not supported", level);
	}

	return ret;
}

static int ov2640_set_output_format(const struct device *dev,
				int output_format)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	/* Switch to DSP register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_DSP);

	if (output_format == VIDEO_PIX_FMT_JPEG)	{
		/* Enable JPEG compression */
		ret |= ov2640_write_reg(&cfg->i2c, IMAGE_MODE, IMAGE_MODE_JPEG_EN);
	} else if (output_format == VIDEO_PIX_FMT_RGB565)	{
		/* Disable JPEG compression and set output to RGB565 */
		ret |= ov2640_write_reg(&cfg->i2c, IMAGE_MODE, IMAGE_MODE_RGB565);
	} else {
		LOG_ERR("Image format not supported");
		return -ENOTSUP;
	}
	k_msleep(30);

	return ret;
}

static int ov2640_set_quality(const struct device *dev, int qs)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	/* Switch to DSP register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_DSP);

	/* Write QS register */
	ret |= ov2640_write_reg(&cfg->i2c, QS, qs);

	return ret;
}

static int ov2640_set_colorbar(const struct device *dev, uint8_t enable)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg;

	/* Switch to SENSOR register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Update COM7 to enable/disable color bar test pattern */
	reg = ov2640_read_reg(&cfg->i2c, COM7);

	if (enable) {
		reg |= COM7_COLOR_BAR;
	} else {
		reg &= ~COM7_COLOR_BAR;
	}

	ret |= ov2640_write_reg(&cfg->i2c, COM7, reg);

	return ret;
}

static int ov2640_set_white_bal(const struct device *dev, int enable)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg;

	/* Switch to SENSOR register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Update CTRL1 to enable/disable automatic white balance*/
	reg = ov2640_read_reg(&cfg->i2c, CTRL1);

	if (enable) {
		reg |= CTRL1_AWB;
	} else {
		reg &= ~CTRL1_AWB;
	}

	ret |= ov2640_write_reg(&cfg->i2c, CTRL1, reg);

	return ret;
}

static int ov2640_set_gain_ctrl(const struct device *dev, int enable)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg;

	/* Switch to SENSOR register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Update COM8 to enable/disable automatic gain control */
	reg = ov2640_read_reg(&cfg->i2c, COM8);

	if (enable) {
		reg |= COM8_AGC_EN;
	} else {
		reg &= ~COM8_AGC_EN;
	}

	ret |= ov2640_write_reg(&cfg->i2c, COM8, reg);

	return ret;
}

static int ov2640_set_exposure_ctrl(const struct device *dev, int enable)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg;

	/* Switch to SENSOR register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Update COM8  to enable/disable automatic exposure control */
	reg = ov2640_read_reg(&cfg->i2c, COM8);

	if (enable) {
		reg |= COM8_AEC_EN;
	} else {
		reg &= ~COM8_AEC_EN;
	}

	ret |= ov2640_write_reg(&cfg->i2c, COM8, reg);

	return ret;
}

static int ov2640_set_horizontal_mirror(const struct device *dev,
				int enable)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg;

	/* Switch to SENSOR register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Update REG04 to enable/disable horizontal mirror */
	reg = ov2640_read_reg(&cfg->i2c, REG04);

	if (enable) {
		reg |= REG04_HFLIP_IMG;
	} else {
		reg &= ~REG04_HFLIP_IMG;
	}

	ret |= ov2640_write_reg(&cfg->i2c, REG04, reg);

	return ret;
}

static int ov2640_set_vertical_flip(const struct device *dev, int enable)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg;

	/* Switch to SENSOR register bank */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);

	/* Update REG04 to enable/disable vertical flip */
	reg = ov2640_read_reg(&cfg->i2c, REG04);

	if (enable) {
		reg |= REG04_VFLIP_IMG;
	} else {
		reg &= ~REG04_VFLIP_IMG;
	}

	ret |= ov2640_write_reg(&cfg->i2c, REG04, reg);

	return ret;
}

static int ov2640_set_resolution(const struct device *dev,
				uint16_t img_width, uint16_t img_height)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint16_t w = img_width;
	uint16_t h = img_height;

	/* Disable DSP */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_DSP);
	ret |= ov2640_write_reg(&cfg->i2c, R_BYPASS, R_BYPASS_DSP_BYPAS);

	/* Write output width */
	ret |= ov2640_write_reg(&cfg->i2c, ZMOW, (w >> 2) & 0xFF); /* OUTW[7:0] (real/4) */
	ret |= ov2640_write_reg(&cfg->i2c, ZMOH, (h >> 2) & 0xFF); /* OUTH[7:0] (real/4) */
	ret |= ov2640_write_reg(&cfg->i2c, ZMHH, ((h >> 8) & 0x04) |
							((w>>10) & 0x03)); /* OUTH[8]/OUTW[9:8] */

	/* Set CLKRC */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);
	ret |= ov2640_write_reg(&cfg->i2c, CLKRC, 0x87);

	/* Write DSP input registers */
	ov2640_write_all(dev, uxga_regs, ARRAY_SIZE(uxga_regs));

	/* Enable DSP */
	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_DSP);
	ret |= ov2640_write_reg(&cfg->i2c, R_BYPASS, R_BYPASS_DSP_EN);

	k_msleep(30);

	return ret;
}

uint8_t ov2640_check_connection(const struct device *dev)
{
	int ret = 0;
	const struct ov2640_config *cfg = dev->config;

	uint8_t reg_pid_val, reg_ver_val;

	ret |= ov2640_write_reg(&cfg->i2c, BANK_SEL, BANK_SEL_SENSOR);
	reg_pid_val = ov2640_read_reg(&cfg->i2c, REG_PID);
	reg_ver_val = ov2640_read_reg(&cfg->i2c, REG_VER);

	if (REG_PID_VAL != reg_pid_val || REG_VER_VAL != reg_ver_val) {
		LOG_ERR("OV2640 not detected\n");
		return -ENODEV;
	}

	return ret;
}

static int ov2640_set_fmt(const struct device *dev,
			enum video_endpoint_id ep, struct video_format *fmt)
{
	struct ov2640_data *drv_data = dev->data;
	uint16_t width, height;
	int ret = 0;
	int i = 0;

	/* We only support RGB565 and JPEG pixel formats */
	if (fmt->pixelformat != VIDEO_PIX_FMT_RGB565 && fmt->pixelformat != VIDEO_PIX_FMT_JPEG) {
		LOG_ERR("ov2640 camera supports only RGB565 and JPG pixelformats!");
		return -ENOTSUP;
	}

	width = fmt->width;
	height = fmt->height;

	if (!memcmp(&drv_data->fmt, fmt, sizeof(drv_data->fmt))) {
		/* nothing to do */
		return 0;
	}

	drv_data->fmt = *fmt;

	/* Set output format */
	ret |= ov2640_set_output_format(dev, fmt->pixelformat);

	/* Check if camera is capable of handling given format */
	while (fmts[i].pixelformat) {
		if (fmts[i].width_min == width && fmts[i].height_min == height &&
			fmts[i].pixelformat == fmt->pixelformat) {
			/* Set window size */
			ret |= ov2640_set_resolution(dev, fmt->width, fmt->height);
			return ret;
		}
		i++;
	}

	/* Camera is not capable of handling given format */
	LOG_ERR("Image format not supported\n");
	return -ENOTSUP;
}

static int ov2640_get_fmt(const struct device *dev,
			enum video_endpoint_id ep, struct video_format *fmt)
{
	struct ov2640_data *drv_data = dev->data;

	*fmt = drv_data->fmt;

	return 0;
}

static int ov2640_stream_start(const struct device *dev)
{
	return 0;
}

static int ov2640_stream_stop(const struct device *dev)
{
	return 0;
}

static int ov2640_get_caps(const struct device *dev,
			   enum video_endpoint_id ep,
			   struct video_caps *caps)
{
	caps->format_caps = fmts;
	return 0;
}

static int ov2640_set_ctrl(const struct device *dev,
				unsigned int cid, void *value)
{
	int ret = 0;

	switch (cid) {
	case VIDEO_CID_HFLIP:
		ret |= ov2640_set_horizontal_mirror(dev, (int)value);
		break;
	case VIDEO_CID_VFLIP:
		ret |= ov2640_set_vertical_flip(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_EXPOSURE:
		ret |= ov2640_set_exposure_ctrl(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_GAIN:
		ret |= ov2640_set_gain_ctrl(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_BRIGHTNESS:
		ret |= ov2640_set_brightness(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_SATURATION:
		ret |= ov2640_set_saturation(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_WHITE_BAL:
		ret |= ov2640_set_white_bal(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_CONTRAST:
		ret |= ov2640_set_contrast(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_COLORBAR:
		ret |= ov2640_set_colorbar(dev, (int)value);
		break;
	case VIDEO_CID_CAMERA_QUALITY:
		ret |= ov2640_set_quality(dev, (int)value);
		break;
	default:
		return -ENOTSUP;
	}

	return ret;
}

static const struct video_driver_api ov2640_driver_api = {
	.set_format = ov2640_set_fmt,
	.get_format = ov2640_get_fmt,
	.get_caps = ov2640_get_caps,
	.stream_start = ov2640_stream_start,
	.stream_stop = ov2640_stream_stop,
	.set_ctrl = ov2640_set_ctrl,
};

static int ov2640_init(const struct device *dev)
{
	struct video_format fmt;
	int ret = 0;

#if DT_INST_NODE_HAS_PROP(0, reset_gpios)
	const struct ov2640_config *cfg = dev->config;

	ret = gpio_pin_configure_dt(&cfg->reset_gpio, GPIO_OUTPUT_ACTIVE);
	if (ret) {
		return ret;
	}

	gpio_pin_set_dt(&cfg->reset_gpio, 0);
	k_sleep(K_MSEC(1));
	gpio_pin_set_dt(&cfg->reset_gpio, 1);
	k_sleep(K_MSEC(1));
#endif

	ret = ov2640_check_connection(dev);

	if (ret) {
		return ret;
	}

	ov2640_soft_reset(dev);
	k_msleep(300);

	ov2640_write_all(dev, default_regs, ARRAY_SIZE(default_regs));

	/* set default/init format SVGA RGB565 */
	fmt.pixelformat = VIDEO_PIX_FMT_RGB565;
	fmt.width = SVGA_HSIZE;
	fmt.height = SVGA_VSIZE;
	fmt.pitch = SVGA_HSIZE * 2;
	ret = ov2640_set_fmt(dev, VIDEO_EP_OUT, &fmt);
	if (ret) {
		LOG_ERR("Unable to configure default format");
		return -EIO;
	}

	ret |= ov2640_set_exposure_ctrl(dev, 1);
	ret |= ov2640_set_white_bal(dev, 1);

	return ret;
}

/* Unique Instance */
static const struct ov2640_config ov2640_cfg_0 = {
	.i2c = I2C_DT_SPEC_INST_GET(0),
#if DT_INST_NODE_HAS_PROP(0, reset_gpios)
	.reset_gpio = GPIO_DT_SPEC_INST_GET(0, reset_gpios),
#endif
};
static struct ov2640_data ov2640_data_0;

static int ov2640_init_0(const struct device *dev)
{
	const struct ov2640_config *cfg = dev->config;

	if (!device_is_ready(cfg->i2c.bus)) {
		LOG_ERR("Bus device is not ready");
		return -ENODEV;
	}

#if DT_INST_NODE_HAS_PROP(0, reset_gpios)
	if (!device_is_ready(cfg->reset_gpio.port)) {
		LOG_ERR("%s: device %s is not ready", dev->name,
				cfg->reset_gpio.port->name);
		return -ENODEV;
	}
#endif

	uint32_t i2c_cfg = I2C_MODE_CONTROLLER |
					I2C_SPEED_SET(I2C_SPEED_STANDARD);

	if (i2c_configure(cfg->i2c.bus, i2c_cfg)) {
		LOG_ERR("Failed to configure ov2640 i2c interface.");
	}

	return ov2640_init(dev);
}

DEVICE_DT_INST_DEFINE(0, &ov2640_init_0, NULL,
			&ov2640_data_0, &ov2640_cfg_0,
			POST_KERNEL, CONFIG_VIDEO_INIT_PRIORITY,
			&ov2640_driver_api);