# nrfx UART configuration

# Copyright (c) 2016 - 2018, Nordic Semiconductor ASA
# SPDX-License-Identifier: Apache-2.0

menuconfig UART_NRFX
	bool "nRF UART nrfx drivers"
	default y
	select SERIAL_HAS_DRIVER
	select SERIAL_SUPPORT_INTERRUPT
	select SERIAL_SUPPORT_ASYNC
	depends on SOC_FAMILY_NRF
	help
	  Enable support for nrfx UART drivers for nRF MCU series.
	  Peripherals with the same instance ID cannot be used together,
	  e.g. UART_0 and UARTE_0.

if UART_NRFX


# ----------------- port 0 -----------------
choice
	prompt "UART Port 0 Driver type"
	optional

config UART_0_NRF_UART
	bool "nRF UART 0"
	depends on HAS_HW_NRF_UART0
	select NRF_UART_PERIPHERAL
	help
	  Enable nRF UART without EasyDMA on port 0.

config UART_0_NRF_UARTE
	bool "nRF UARTE 0"
	# In nRF91 Series SoCs, UART peripherals share certain resources with
	# SPI and TWI peripherals having the same instance number, and therefore
	# these cannot be used simultaneously.
	depends on HAS_HW_NRF_UARTE0 && !(SOC_SERIES_NRF91X && (SPI_0 || I2C_0))
	select NRF_UARTE_PERIPHERAL
	help
	  Enable nRF UART with EasyDMA on port 0.
endchoice

if UART_0_NRF_UART || UART_0_NRF_UARTE

config UART_0_INTERRUPT_DRIVEN
	bool "Enable interrupt support on port 0"
	depends on UART_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART interrupt support on port 0.

config UART_0_ASYNC
	bool "Enable Asynchronous API support on port 0"
	depends on UART_ASYNC_API && !UART_0_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART Asynchronous API support on port 0.

config UART_0_NRF_PARITY_BIT
	bool "Enable parity bit"
	help
	  Enable parity bit.

config UART_0_NRF_FLOW_CONTROL
	bool "Enable flow control"
	help
	  Enable flow control. If selected, additionally two pins, RTS and CTS
	  have to be configured.

config UART_0_NRF_TX_BUFFER_SIZE
	int "Size of RAM buffer"
	depends on UART_0_NRF_UARTE
	range 1 65535
	default 32
	help
	  Size of the transmit buffer for API function: fifo_fill.
	  This value is limited by range of TXD.MAXCNT register for
	  particular SoC.

config UART_0_NRF_HW_ASYNC
	bool "Use hardware RX byte counting"
	depends on UART_0_NRF_UARTE
	depends on UART_ASYNC_API
	help
	  If default driver uses interrupts to count incoming bytes, it is possible
	  that with higher speeds and/or high cpu load some data can be lost.
	  It is recommended to use hardware byte counting in such scenarios.
	  Hardware RX byte counting requires timer instance and one PPI channel

config UART_0_NRF_HW_ASYNC_TIMER
	int "Timer instance"
	depends on UART_0_NRF_HW_ASYNC

config UART_0_GPIO_MANAGEMENT
	bool "Enable GPIO management on port 0"
	depends on UART_0_NRF_UARTE && DEVICE_POWER_MANAGEMENT
	default y
	help
	  If enabled, the driver will configure the GPIOs used by the uart to
	  their default configuration when device is powered down. The GPIOs
	  will be configured back to correct state when UART is powered up.

endif # UART_0_NRF_UART || UART_0_NRF_UARTE

# ----------------- port 1 -----------------
config UART_1_NRF_UARTE
	bool "nRF UARTE 1"
	# In nRF91 Series SoCs, UART peripherals share certain resources with
	# SPI and TWI peripherals having the same instance number, and therefore
	# these cannot be used simultaneously.
	depends on HAS_HW_NRF_UARTE1 && !(SOC_SERIES_NRF91X && (SPI_1 || I2C_1))
	select NRF_UARTE_PERIPHERAL
	help
	  Enable nRF UART with EasyDMA on port 1.

if UART_1_NRF_UARTE

config UART_1_INTERRUPT_DRIVEN
	bool "Enable interrupt support on port 1"
	depends on UART_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART interrupt support on port 1.

config UART_1_ASYNC
	bool "Enable Asynchronous API support on port 1"
	depends on UART_ASYNC_API && !UART_1_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART Asynchronous API support on port 1.

config UART_1_NRF_PARITY_BIT
	bool "Enable parity bit"
	help
	  Enable parity bit.

config UART_1_NRF_FLOW_CONTROL
	bool "Enable flow control"
	help
	  Enable flow control. If selected, additionally two pins, RTS and CTS
	  have to be configured.

config UART_1_NRF_TX_BUFFER_SIZE
	int "Size of RAM buffer"
	depends on UART_INTERRUPT_DRIVEN
	range 1 65535
	default 32
	help
	  Size of the transmit buffer for API function: fifo_fill.
	  This value is limited by range of TXD.MAXCNT register for
	  particular SoC.

config UART_1_NRF_HW_ASYNC
	bool "Use hardware RX byte counting"
	depends on UART_1_ASYNC
	help
	  If default driver uses interrupts to count incoming bytes, it is possible
	  that with higher speeds and/or high cpu load some data can be lost.
	  It is recommended to use hardware byte counting in such scenarios.
	  Hardware RX byte counting requires timer instance and one PPI channel

config UART_1_NRF_HW_ASYNC_TIMER
	int "Timer instance"
	depends on UART_1_NRF_HW_ASYNC

config UART_1_GPIO_MANAGEMENT
	bool "Enable GPIO management on port 1"
	depends on DEVICE_POWER_MANAGEMENT
	default y
	help
	  If enabled, the driver will configure the GPIOs used by the uart to
	  their default configuration when device is powered down. The GPIOs
	  will be configured back to correct state when UART is powered up.

endif # UART_1_NRF_UARTE

# ----------------- port 2 -----------------
config UART_2_NRF_UARTE
	bool "nRF UARTE 2"
	# In nRF91 Series SoCs, UART peripherals share certain resources with
	# SPI and TWI peripherals having the same instance number, and therefore
	# these cannot be used simultaneously.
	depends on HAS_HW_NRF_UARTE2 && !(SOC_SERIES_NRF91X && (SPI_2 || I2C_2))
	select NRF_UARTE_PERIPHERAL
	help
	  Enable nRF UART with EasyDMA on port 2.

if UART_2_NRF_UARTE

config UART_2_INTERRUPT_DRIVEN
	bool "Enable interrupt support on port 2"
	depends on UART_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART interrupt support on port 2.

config UART_2_ASYNC
	bool "Enable Asynchronous API support on port 2"
	depends on UART_ASYNC_API && !UART_2_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART Asynchronous API support on port 2.

config UART_2_NRF_PARITY_BIT
	bool "Enable parity bit"
	help
	  Enable parity bit.

config UART_2_NRF_FLOW_CONTROL
	bool "Enable flow control"
	help
	  Enable flow control. If selected, additionally two pins, RTS and CTS
	  have to be configured.

config UART_2_NRF_TX_BUFFER_SIZE
	int "Size of RAM buffer"
	range 1 65535
	default 32
	help
	  Size of the transmit buffer for API function: fifo_fill.
	  This value is limited by range of TXD.MAXCNT register for
	  particular SoC.

config UART_2_NRF_HW_ASYNC
	bool "Use hardware RX byte counting"
	depends on UART_2_ASYNC
	help
	  If default driver uses interrupts to count incoming bytes, it is possible
	  that with higher speeds and/or high cpu load some data can be lost.
	  It is recommended to use hardware byte counting in such scenarios.
	  Hardware RX byte counting requires timer instance and one PPI channel

config UART_2_NRF_HW_ASYNC_TIMER
	int "Timer instance"
	depends on UART_2_NRF_HW_ASYNC

config UART_2_GPIO_MANAGEMENT
	bool "Enable GPIO management on port 2"
	depends on DEVICE_POWER_MANAGEMENT
	default y
	help
	  If enabled, the driver will configure the GPIOs used by the uart to
	  their default configuration when device is powered down. The GPIOs
	  will be configured back to correct state when UART is powered up.

endif # UART_2_NRF_UARTE

# ----------------- port 3 -----------------
config UART_3_NRF_UARTE
	bool "nRF UARTE 3"
	# In nRF91 Series SoCs, UART peripherals share certain resources with
	# SPI and TWI peripherals having the same instance number, and therefore
	# these cannot be used simultaneously.
	depends on HAS_HW_NRF_UARTE3 && !(SOC_SERIES_NRF91X && (SPI_3 || I2C_3))
	select NRF_UARTE_PERIPHERAL
	help
	  Enable nRF UART with EasyDMA on port 3.

if UART_3_NRF_UARTE

config UART_3_INTERRUPT_DRIVEN
	bool "Enable interrupt support on port 3"
	depends on UART_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART interrupt support on port 3.

config UART_3_ASYNC
	bool "Enable Asynchronous API support on port 3"
	depends on UART_ASYNC_API && !UART_3_INTERRUPT_DRIVEN
	default y
	help
	  This option enables UART Asynchronous API support on port 3.

config UART_3_NRF_PARITY_BIT
	bool "Enable parity bit"
	help
	  Enable parity bit.

config UART_3_NRF_FLOW_CONTROL
	bool "Enable flow control"
	help
	  Enable flow control. If selected, additionally two pins, RTS and CTS
	  have to be configured.

config UART_3_NRF_TX_BUFFER_SIZE
	int "Size of RAM buffer"
	range 1 65535
	default 32
	help
	  Size of the transmit buffer for API function: fifo_fill.
	  This value is limited by range of TXD.MAXCNT register for
	  particular SoC.

config UART_3_NRF_HW_ASYNC
	bool "Use hardware RX byte counting"
	depends on UART_3_ASYNC
	help
	  If default driver uses interrupts to count incoming bytes, it is possible
	  that with higher speeds and/or high cpu load some data can be lost.
	  It is recommended to use hardware byte counting in such scenarios.
	  Hardware RX byte counting requires timer instance and one PPI channel

config UART_3_NRF_HW_ASYNC_TIMER
	int "Timer instance"
	depends on UART_3_NRF_HW_ASYNC

config UART_3_GPIO_MANAGEMENT
	bool "Enable GPIO management on port 3"
	depends on DEVICE_POWER_MANAGEMENT
	default y
	help
	  If enabled, the driver will configure the GPIOs used by the uart to
	  their default configuration when device is powered down. The GPIOs
	  will be configured back to correct state when UART is powered up.

endif # UART_3_NRF_UARTE


config NRFX_TIMER0
	default y
	depends on UART_0_NRF_HW_ASYNC_TIMER = 0 || UART_1_NRF_HW_ASYNC_TIMER = 0 || \
		   UART_3_NRF_HW_ASYNC_TIMER = 0 || UART_2_NRF_HW_ASYNC_TIMER = 0

config NRFX_TIMER1
	default y
	depends on UART_0_NRF_HW_ASYNC_TIMER = 1 || UART_1_NRF_HW_ASYNC_TIMER = 1 || \
		   UART_3_NRF_HW_ASYNC_TIMER = 1 || UART_2_NRF_HW_ASYNC_TIMER = 1

config NRFX_TIMER2
	default y
	depends on UART_0_NRF_HW_ASYNC_TIMER = 2 || UART_1_NRF_HW_ASYNC_TIMER = 2 || \
		   UART_3_NRF_HW_ASYNC_TIMER = 2 || UART_2_NRF_HW_ASYNC_TIMER = 2

config NRFX_TIMER3
	default y
	depends on UART_0_NRF_HW_ASYNC_TIMER = 3 || UART_1_NRF_HW_ASYNC_TIMER = 3 || \
		   UART_3_NRF_HW_ASYNC_TIMER = 3 || UART_2_NRF_HW_ASYNC_TIMER = 3

config NRFX_TIMER4
	default y
	depends on UART_0_NRF_HW_ASYNC_TIMER = 4 || UART_1_NRF_HW_ASYNC_TIMER = 4 || \
		   UART_3_NRF_HW_ASYNC_TIMER = 4 || UART_2_NRF_HW_ASYNC_TIMER = 4


if UART_0_NRF_HW_ASYNC || UART_1_NRF_HW_ASYNC || UART_2_NRF_HW_ASYNC || UART_3_NRF_HW_ASYNC

config NRFX_TIMER
	default y

config NRFX_PPI
	depends on HAS_HW_NRF_PPI
	default y

config NRFX_DPPI
	depends on HAS_HW_NRF_DPPIC
	default y

config UARTE_NRF_HW_ASYNC
	bool
	default y

endif

config NRF_UART_PERIPHERAL
	bool

config NRF_UARTE_PERIPHERAL
	bool

endif # UART_NRFX