# Copyright 2019,2024 NXP
# SPDX-License-Identifier: Apache-2.0

config SOC_SERIES_LPC55XXX
	select HAS_MCUX
	select HAS_MCUX_FLEXCOMM
	select HAS_MCUX_SYSCON
	select HAS_MCUX_WWDT
	select CPU_CORTEX_M_HAS_SYSTICK
	select CPU_CORTEX_M_HAS_DWT
	select PLATFORM_SPECIFIC_INIT

config SOC_LPC55S06
	select CPU_CORTEX_M33
	select CPU_HAS_ARM_SAU
	select CPU_HAS_ARM_MPU
	select CPU_HAS_FPU
	select ARMV8_M_DSP
	select ARM_TRUSTZONE_M
	select HAS_MCUX_IAP if !TRUSTED_EXECUTION_NONSECURE
	select HAS_MCUX_RNG

config SOC_LPC55S16
	select CPU_CORTEX_M33
	select CPU_HAS_ARM_SAU
	select CPU_HAS_ARM_MPU
	select CPU_HAS_FPU
	select ARMV8_M_DSP
	select ARM_TRUSTZONE_M
	select HAS_MCUX_IAP if !TRUSTED_EXECUTION_NONSECURE
	select HAS_MCUX_MCAN
	select HAS_MCUX_RNG

config SOC_LPC55S28
	select CPU_CORTEX_M33
	select CPU_HAS_ARM_SAU
	select CPU_HAS_ARM_MPU
	select CPU_HAS_FPU
	select ARMV8_M_DSP
	select HAS_MCUX_IAP
	select HAS_MCUX_LPADC
	select HAS_MCUX_LPC_DMA
	select HAS_MCUX_RNG

config SOC_LPC55S36
	select CPU_CORTEX_M33
	select CPU_HAS_ARM_SAU
	select CPU_HAS_ARM_MPU
	select CPU_HAS_FPU
	select ARMV8_M_DSP
	select ARM_TRUSTZONE_M
	select HAS_MCUX_MCAN
	select HAS_MCUX_PWM

config SOC_LPC55S69
	select CPU_CORTEX_M33

config SOC_LPC55S69_CPU0
	select CPU_HAS_ARM_SAU
	select CPU_HAS_ARM_MPU
	select CPU_HAS_FPU
	select ARMV8_M_DSP
	select ARM_TRUSTZONE_M
	select HAS_MCUX_IAP
	select HAS_MCUX_LPADC
	select HAS_MCUX_LPC_DMA
	select HAS_MCUX_USB_LPCIP3511
	select HAS_MCUX_CTIMER
	select HAS_MCUX_SCTIMER
	select HAS_MCUX_RNG

if SOC_SERIES_LPC55XXX

config INIT_PLL0
	bool "Initialize PLL0"

config INIT_PLL1
	bool "Initialize PLL1"
	default "y"
	depends on !(SOC_LPC55S06 || FLASH || BUILD_WITH_TFM)
	help
	  In the LPC55XXX Family, this is currently being used to set the
	  core clock value at it's highest frequency which clocks at 150MHz.
	  Note that flash programming operations are limited to 100MHz, and
	  this PLL should not be used as the core clock in those cases.

config SECOND_CORE_MCUX
	bool "LPC55xxx's second core"

config SECOND_CORE_BOOT_ADDRESS_MCUX
	depends on SECOND_CORE_MCUX
	hex "Address the second core will boot at"
	default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_CPU1_PARTITION))
	help
	  This is the address the second core will boot from.

config LPC55XXX_SRAM_CLOCKS
	bool "CLock LPC SRAM banks"

config LPC55XXX_USB_RAM
	bool

if SOC_LPC55S69

config SOC_FLASH_MCUX
	bool

endif # SOC_LPC55S69

config MCUX_CORE_SUFFIX
	default "_cm33_core0" if SOC_LPC55S69_CPU0
	default "_cm33_core1" if SOC_LPC55S69_CPU1

endif # SOC_SERIES_LPC55XXX