# Thingy53 NRF5340 board configuration

# Copyright (c) 2021 Nordic Semiconductor ASA
# SPDX-License-Identifier: Apache-2.0

config THINGY53_MISO_WORKAROUND
	bool "MISO workaround"
	default SPI
	help
	  Workaround SPI bus MISO issues. The workaround sets dedicated pin
	  high in order to avoid voltage drops on the SPI MISO line.

config THINGY53_INIT_PRIORITY
	int "Init priority"
	default 79
	help
	  Initialization priority of the Thingy:53.

config IPM_NRFX
	default IPM

config RPMSG_SERVICE_DUAL_IPM_SUPPORT
	default RPMSG_SERVICE

if RPMSG_SERVICE_DUAL_IPM_SUPPORT

config IPM_MSG_CH_0_ENABLE
	default y

config IPM_MSG_CH_1_ENABLE
	default y

config RPMSG_SERVICE_IPM_TX_NAME
	default "IPM_0" if RPMSG_SERVICE_MODE_MASTER
	default "IPM_1" if RPMSG_SERVICE_MODE_REMOTE

config RPMSG_SERVICE_IPM_RX_NAME
	default "IPM_1" if RPMSG_SERVICE_MODE_MASTER
	default "IPM_0" if RPMSG_SERVICE_MODE_REMOTE

config IPM_MSG_CH_0_TX
	default RPMSG_SERVICE_MODE_MASTER

config IPM_MSG_CH_0_RX
	default RPMSG_SERVICE_MODE_REMOTE

config IPM_MSG_CH_1_TX
	default RPMSG_SERVICE_MODE_REMOTE

config IPM_MSG_CH_1_RX
	default RPMSG_SERVICE_MODE_MASTER

endif # RPMSG_SERVICE_DUAL_IPM_SUPPORT

if BOARD_THINGY53_NRF5340_CPUAPP || BOARD_THINGY53_NRF5340_CPUAPPNS

config BOARD_ENABLE_DCDC_APP
	bool "Enable Application MCU DCDC converter"
	select SOC_DCDC_NRF53X_APP
	default y

config BOARD_ENABLE_DCDC_NET
	bool "Enable Network MCU DCDC converter"
	select SOC_DCDC_NRF53X_NET
	default y

config BOARD_ENABLE_DCDC_HV
	bool "Enable High Voltage DCDC converter"
	select SOC_DCDC_NRF53X_HV
	default y

config BOARD_ENABLE_CPUNET
	bool "Enable nRF53 Network MCU"
	help
	  This option enables releasing the Network 'force off' signal, which
	  as a consequence will power up the Network MCU during system boot.
	  Additionally, the option allocates GPIO pins that will be used by UARTE
	  of the Network MCU.
	  Note: GPIO pin allocation can only be configured by the secure Application
	  MCU firmware, so when this option is used with the non-secure version of
	  the board, the application needs to take into consideration, that the
	  secure firmware image must already have configured GPIO allocation for the
	  Network MCU.
	default y if (BT || NRF_802154_SER_HOST)

config DOMAIN_CPUNET_BOARD
	string
	default "thingy53_nrf5340_cpunet"
	depends on BOARD_ENABLE_CPUNET
	help
	  The board which will be used for CPUNET domain when creating a multi
	  image application where one or more images should be located on
	  another board. For example hci_rpmsg on the nRF5340_cpunet for
	  Bluetooth applications.

endif # BOARD_THINGY53_NRF5340_CPUAPP || BOARD_THINGY53_NRF5340_CPUAPPNS

if BOARD_THINGY53_NRF5340_CPUNET

config DOMAIN_CPUAPP_BOARD
	string
	default "thingy53_nrf5340_cpuapp"
	help
	  The board which will be used for CPUAPP domain when creating a multi
	  image application where one or more images should be located on
	  another board.

endif # BOARD_THINGY53_NRF5340_CPUNET