# Copyright (c) 2021 Arm Limited (or its affiliates). All rights reserved.
# SPDX-License-Identifier: Apache-2.0

set(SUPPORTED_EMU_PLATFORMS armfvp)
set(ARMFVP_BIN_NAME FVP_BaseR_AEMv8R)
set(ARMFVP_MIN_VERSION 11.16.16)

if(CONFIG_BOARD_FVP_BASER_AEMV8R_FVP_AEMV8R_AARCH64)
  set(ARMFVP_FLAGS
    -C cluster0.has_aarch64=1
    -C cluster0.VMSA_supported=0
    -C cluster0.NUM_CORES=${CONFIG_MP_MAX_NUM_CPUS}
    -C cluster0.gicv3.cpuintf-mmap-access-level=2
    -C cluster0.gicv3.SRE-enable-action-on-mmap=2
    -C cluster0.gicv3.SRE-EL2-enable-RAO=1
    -C cluster0.gicv3.extended-interrupt-range-support=1
    -C gic_distributor.GICD_CTLR-DS-1-means-secure-only=1
    -C gic_distributor.has-two-security-states=0
    -C bp.refcounter.non_arch_start_at_default=1
    # UART0 config
    -C bp.pl011_uart0.out_file=-
    -C bp.pl011_uart0.unbuffered_output=1
    -C bp.terminal_0.start_telnet=0
    # UART1 config
    -C bp.pl011_uart1.out_file=-
    -C bp.pl011_uart1.unbuffered_output=1
    -C bp.terminal_1.start_telnet=0
    # UART2 config
    -C bp.pl011_uart2.out_file=-
    -C bp.pl011_uart2.unbuffered_output=1
    -C bp.terminal_2.start_telnet=0
    # UART3 config
    -C bp.pl011_uart3.out_file=-
    -C bp.pl011_uart3.unbuffered_output=1
    -C bp.terminal_3.start_telnet=0

    -C bp.vis.disable_visualisation=1
    -C bp.vis.rate_limit-enable=0
    -C cache_state_modelled=1
    )
elseif(CONFIG_BOARD_FVP_BASER_AEMV8R_FVP_AEMV8R_AARCH32)
  set(ARMFVP_FLAGS
    -C cluster0.has_aarch64=0
    -C cluster0.VMSA_supported=0
    -C cluster0.NUM_CORES=${CONFIG_MP_MAX_NUM_CPUS}
    -C cluster0.gicv3.cpuintf-mmap-access-level=2
    -C cluster0.gicv3.SRE-enable-action-on-mmap=2
    -C cluster0.gicv3.SRE-EL2-enable-RAO=1
    -C cluster0.gicv3.extended-interrupt-range-support=1
    -C gic_distributor.GICD_CTLR-DS-1-means-secure-only=1
    -C gic_distributor.has-two-security-states=0
    -C bp.refcounter.non_arch_start_at_default=1
    # UART0 config
    -C bp.pl011_uart0.out_file=-
    -C bp.pl011_uart0.unbuffered_output=1
    -C bp.terminal_0.start_telnet=0
    # UART1 config
    -C bp.pl011_uart1.out_file=-
    -C bp.pl011_uart1.unbuffered_output=1
    -C bp.terminal_1.start_telnet=0
    # UART2 config
    -C bp.pl011_uart2.out_file=-
    -C bp.pl011_uart2.unbuffered_output=1
    -C bp.terminal_2.start_telnet=0
    # UART3 config
    -C bp.pl011_uart3.out_file=-
    -C bp.pl011_uart3.unbuffered_output=1
    -C bp.terminal_3.start_telnet=0

    -C bp.vis.disable_visualisation=1
    -C bp.vis.rate_limit-enable=0
    -C cache_state_modelled=0
    )
endif()