# Copyright(c) 2024 Intel Corporation.
# SPDX - License - Identifier : Apache - 2.0

compatible: "snps,dwcxgmac"

description: Synopsys DesignWareCore XGMAC

include:
  - name: reset-device.yaml
  - name: ethernet-controller.yaml

properties:
  reg:
    required: true
  interrupts:
    required: true
  max-frame-size:
    type: int
    default: 1518
    description: |
      Maximum ethernet frame size.  The current ethernet frame sizes
      supported by hardware are standard and jumbo (up to 16KB) frames. This
      means that normally xgmac will reject any frame above max-frame-size
      value.  The default value is 1518, which represents an usual
      IEEE 802.3 ethernet frame:
        Ethernet Frame [ 14 MAC HEADER | 1500 MTU | 4 FCS ] = 1518 bytes
  max-speed:
    type: int
    enum:
      - 10
      - 100
      - 1000
      - 2500
    default: 1000
    description: |
      This specifies maximum speed in Mbit/s supported by the device.  The
      xgmac driver supports 10Mbit/s, 100Mbit/s, 1000Mbit/s, and 2500Mbit/s.  Using 1000,
      as default value, enables driver to configure 10 and 100Mbit/s speeds.
      2500Mbit/s speed can be used only with Soft PCS. When selected driver assumes
      soft PCS is connected to XGMAC through GMII. make sure the phy-connection-type is
      selected as gmii when 2500Mbit/s speed is selected.
  tx-fifo-size:
    type: int
    enum:
      - 1024
      - 2048
      - 4096
      - 8192
      - 16384
      - 32768
      - 65536
      - 131072
      - 262144
    default: 32768
    description: |
      Specifies the size of the MTL Transmit FIFO
  rx-fifo-size:
    type: int
    enum:
      - 1024
      - 2048
      - 4096
      - 8192
      - 16384
      - 32768
      - 65536
      - 131072
      - 262144
    default: 32768
    description: |
      Specifies the size of the MTL Receive FIFO
  num-dma-ch:
    type: int
    required: true
    description: |
      Number of dma channels range: 1 to 8.
  num-tx-queues:
    type: int
    required: true
    description: |
      Number of hardware TX queues range: 1 to 8.
  num-rx-queues:
    type: int
    required: true
    description: |
      Number of hardware RX queues range: 1 to 8.
  num-tc:
    type: int
    default: 1
    description: |
      Number of traffic classes range: 1 to 7.
  full-duplex-mode-en:
    type: boolean
    required: true
    description: |
      MAC communication mode to full duplex mode.
  wr-osr-lmt:
    type: int
    default: 31
    description: |
      AXI Maximum Write Outstanding Request Limit.This value
      limits the maximum outstanding request on the AXI write
      interface. Maximum outstanding requests = WR_OSR_LMT + 1
  rd-osr-lmt:
    type: int
    default: 31
    description: |
      AXI Maximum Read Outstanding Request Limit.This value
      limits the maximum outstanding request on the AXI read
      interface. Maximum outstanding requests = WR_OSR_LMT + 1
  pbl:
    type: int
    default: 32
    description: |
      Programmable burst length range: 4,5,16,32,64,128,256
  edma-tdps:
    type: int
    default: 1
    description: |
      Tx Descriptor Pre-fetch threshold Size.
      This field controls the threshold in the Descriptor cache after
      which the DMA starts pre-fetching the TxDMA descriptors. The
      DMA engine for all TxDMA channels initiate requests for the
      descriptor fetches as soon as the number of descriptors in the
      cache memory for that DMA channel, falls below or equal to
      the programmed threshold (each descriptor is 16 bytes)
      Range: 0,1,2,3,4,5
  edma-rdps:
    type: int
    default: 1
    description: |
      Rx Descriptor Pre-fetch threshold Size.
      This field controls the threshold in the Descriptor cache after
      which the DMA starts pre-fetching the RxDMA descriptors. The
      DMA engine for all RxDMA channels initiate requests for the
      descriptor fetches as soon as the number of descriptors in the
      cache memory for that DMA channel, falls below or equal to
      the programmed threshold (each descriptor is 16 bytes)
      Range: 0,1,2,3,4,5
  pblx8:
    type: boolean
    description: |
      8xPBL mode.
      When this is set to true, the PBL value is multiplied eight times.
      Therefore, the DMA transfers the data in 8, 16, 32, 64, 128, and 256
      beats depending on the PBL value.
  ubl:
    type: boolean
    description: |
      AXI Undefined Burst Length.
      1: The AXI master can perform burst transfers that are equal to or less
      than the maximum allowed burst length enabled.
      0: The AXI master performs one of the following burst transfers: Burst
      transfers of fixed burst lengths as indicated by the BLEN256, BLEN128,
      BLEN64, BLEN32, BLEN16, BLEN8, or BLEN4 field.
  blen4:
    type: boolean
    description: |
      AXI Burst Length 4.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 4 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  blen8:
    type: boolean
    description: |
      AXI Burst Length 8.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 8 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  blen16:
    type: boolean
    description: |
      AXI Burst Length 16.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 16 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  blen32:
    type: boolean
    description: |
      AXI Burst Length 32.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 32 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  blen64:
    type: boolean
    description: |
      AXI Burst Length 64.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 64 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  blen128:
    type: boolean
    description: |
      AXI Burst Length 128.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 128 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  blen256:
    type: boolean
    description: |
      AXI Burst Length 256.
      When this enabled and the mixed_burst is disabled, the AXI master
      can select a burst length of 256 on the AXI interface.
      When the mixed_burst enabled, enabling this field has no effect.
  aal:
    type: boolean
    description: |
      Address-Aligned Beats.
      When this is enabled, the AXI master performs address-aligned
      burst transfers on Read and Write channels.
  eame:
    type: boolean
    description: |
      Enhanced Address Mode Enable.
      DMA master enables the enhanced address mode (40-bit or 48-bit addressing mode).
      In this mode, the DMA engine uses either the 40-bit or 48-bit address, depending
      on the configuration.
  dma-ch-mss:
    type: int
    default: 4096
    description: |
      Maximum Segment Size.
      This field specifies the maximum segment size that must be
      used while segmenting the Transmit packet. This field is valid
      only if the TSE enabled.
  dma-ch-tdrl:
    type: int
    default: 512
    description: |
      Transmit Descriptor Ring Length.
      This field sets the maximum number of Tx descriptors in the
      circular descriptor ring. The maximum number of descriptors is
      limited to 16384 descriptors.
  dma-ch-rdrl:
    type: int
    default: 512
    description: |
      Receive Descriptor Ring Length.
      This field sets the maximum number of Rx descriptors in the
      circular descriptor ring. The maximum number of descriptors is
      limited to 16384 descriptors.
  dma-ch-rbsz:
    type: int
    default: 16383
    description: |
      Receive Buffer size.
      This field indicates the size of the Rx buffers specified in bytes
      allocated by the software to store the packets the Rx DMA
      transfers to the host memory. The maximum buffer size is
      limited to 16K bytes. The buffer size is applicable to payload
      buffers when split headers are enabled.
  dma-ch-arbs:
    type: int
    default: 0
    description: |
      Alternate Receive Buffer Size
      Indicates size in bytes for Buffer 1 when ARBS is set
      to a non-zero value (when split header(SPH) feature is not enabled).
      When split header feature is enabled, ARBS indicates the
      buffer size for header data. The maximum alternate buffer is
      limited to 1016 or 1008-bytes depending on the data bus
      widths (64-bit or 128-bit respectively). When ARBS=0, Rx
      Buffer1 and Rx Buffer2 sizes are based on RBSZ field. Width of
      ARBS field is 7 or 6-bits depending on the data bus widths
      (64-bit or 128-bit respectively).
  dma-ch-rxpbl:
    type: int
    default: 32
    description: |
      Receive Programmable Burst Length.
      These field indicate the maximum number of beats to be
      transferred in one DMA data transfer.
  dma-ch-txpbl:
    type: int
    default: 32
    description: |
      Transmit   Programmable Burst Length.
      These field indicate the maximum number of beats to be
      transferred in one DMA data transfer.
  dma-ch-sph:
    type: boolean
    description: |
      Header-Payload Split.
      When this field is set, the DMA splits the header and payload in
      the Receive path. The DMA writes the header to the Buffer
      Address1. The DMA writes the payload to the buffer to which
      the Buffer Address2 is pointing.
      The software must ensure that the header fits into the Receive
      buffers. If the header length exceeds the receive buffer size,
      the DMA does not split the header and payload.
  dma-ch-edse:
    type: boolean
    description: |
      Enhanced Descriptor Enable.
      When this field is set, the corresponding channel uses
      enhanced Descriptors.
  dma-ch-tse:
    type: boolean
    description: |
      TCP Segmentation Enabled.
      When this field is set, the DMA performs the TCP segmentation
      for packets in Channel. The TCP segmentation is done only
      for those packets for which the TSE is set in the Tx Normal
      descriptor.
  dma-ch-osp:
    type: boolean
    description: |
      Operate on Second Packet.
      When this field is set, it instructs the DMA to process the second
      packet of the Transmit data even before closing the descriptor
      of the first packet.
  mtl-raa:
    type: boolean
    description: |
      Receive Arbitration Algorithm.
      This field is used to select the arbitration algorithm for the Rx
      side. 0: Strict Priority (SP), 1: Weighted Strict Priority (WSP)
  mtl-etsalg:
    type: int
    default: 0
    description: |
      ETS Algorithm.
      This field selects the type of ETS algorithm to be applied for
      traffic classes whose transmission selection algorithm (TSA) is
      set to ETS:
      0: WRR algorithm
      1: WFQ algorithm
      2: DWRR algorithm
  rxq-dyn-dma-en:
    type: int
    default: 1
    description: |
      Receive Queue Enabled for Dynamic DMA Channel Selection.
      Each bit position of this field maps to a queue. there are total 8 queues
  rxq-dma-ch-sel:
    type: uint8-array
    default: [0, 1, 2, 3, 4, 5, 6, 7]
    description: |
      Receive Queue Mapped to DMA Channel. this field does not have
      effect when rxQ-DynDma-En is enabled.
      range 0 - 7
  txq-size:
    type: uint8-array
    default: [127]
    description: |
      This field indicates the size of the allocated Transmit queues
      in blocks of 256 bytes. = (txQ-size + 1) x 256
      range: 0 - 7
  map-queue-tc:
    type: uint8-array
    default: [0]
    description: |
      Queue to Traffic Class Mapping. range 0 - 7
  tx-threshold-ctrl:
    type: uint8-array
    default: [0]
    description: |
          Transmit Threshold Control.
          These field control the threshold level of the MTL Tx Queue.
          Transmission starts when the packet size within the MTL Tx
          Queue is larger than the threshold. In addition, full packets
          with length less than the threshold are also transmitted. This
          field us used only when Transmit Store and Forward is disabled.
          range 0 - 7
                0: 64
                1: reserved
                2: 96
                3: 128
                4: 192
                5: 256
                6: 384
                7: 512
  rx-threshold-ctrl:
    type: uint8-array
    default: [0]
    description: |
          The received packet is transferred to the application or DMA
          when the packet size within the MTL Rx queue is larger than
          the threshold. In addition, full packets with length less than the
          threshold are automatically transferred. The value of 11 is not
          applicable if the size of the configured Rx Queue is 128 bytes.
          This field is valid only when the RSF bit is zero. This field is
          ignored when the RSF field is set to 1.
          range 0 - 3
                0: 64
                1: reserved
                2: 96
                3: 128
  rxq-size:
    type: uint8-array
    default: [127]
    description: |
      Receive Queue Size. This field indicates the size of the allocated
      Receive queues in blocks 256 bytes. = (rxQ-size + 1) x 256
      Range: 0 - 127 ,
  tx-store-fwrd-en:
    type: int
    default: 255
    description: |
      Transmit Store and Forward. When this field is set, the transmission
      starts when a full packet resides in the MTL Tx Queue.
      Each bit position of this field maps to a queue. there are total 8 queues
  hfc-en:
    type: int
    default: 0
    description: |
      Enable Hardware Flow Control. When this field is set, the flow control
      signal operation, based on the fill-level of Rx queue, is enabled.
      Each bit position of this field maps to a queue. there are total 8 queues
  cs-error-pkt-drop-dis:
    type: int
    default: 0
    description: |
      Disable Dropping of TCP/IP Checksum Error Packets
      Each bit position of this field maps to a queue. there are total 8 queues
  rx-store-fwrd-en:
    type: int
    default: 255
    description: |
      Receive Store and Forward. When this field is set, DWC_xgmac reads a
      packet from the Rx queue only after the complete packet has been written to it.
      Each bit position of this field maps to a queue. there are total 8 queues
  fep-en:
    type: int
    default: 0
    description: |
      Forward Error Packets.  When this bit is set, all packets except the runt error
      packets are forwarded to the application or DMA.
      Each bit position of this field maps to a queue. there are total 8 queues
  fup-en:
    type: int
    default: 0
    description: |
      Forward Undersized Good Packets. When this field is set, the Rx queue forwards
      the undersized good packets.
      Each bit position of this field maps to a queue. there are total 8 queues
  priorities-map-tc:
    type: array
    default: [0]
    description: |
      Priorities Mapped to Traffic Class. This field determines if the transmit
      queues associated with the traffic class should be blocked from transmitting
      for the specified pause time when a PFC packet is received with priorities
      matching the priorities programmed in this field.
      range: 0 - 7 and max array size is 8
      ex: <0,1,2,3,4,5,6,7>
  tx-sel-algorithm:
    type: uint8-array
    default: [0]
    description: |
      Transmission Selection Algorithm. This field is used to assign a transmission
      selection algorithm for this traffic class.
      range: 0 -strict priority
             1 - Credit based shaper
             2 - Enhanced Transmission Selection
  jumbo-pkt-en:
    type: boolean
    description: |
      Jumbo Packet Enable.
      When this bit is set, the MAC allows jumbo packets of 9018
      bytes (9022 bytes for VLAN tagged packets) without reporting
      a giant packet error in the Rx packet status
  gaint-pkt-size-limit:
    type: int
    default: 9018
    description: |
      Giant Packet Size Limit.
      If the received packet size is greater than the value
      programmed in this field in units of bytes, the MAC declares
      the received packet as Giant packet. The value programmed in
      this field must be greater than or equal to 1518 bytes. Any
      other programmed value is considered as 1518 bytes.