/*
 * Copyright (c) 2018 - 2020 Antmicro <www.antmicro.com>
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <zephyr/dt-bindings/i2c/i2c.h>

/ {
	#address-cells = <1>;
	#size-cells = <1>;
	compatible = "litex,vexriscv", "litex-dev";
	model = "litex,vexriscv";

	chosen {
		zephyr,entropy = &prbs0;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu0: cpu@0 {
			clock-frequency = <100000000>;
			compatible = "litex,vexriscv-standard", "riscv";
			device_type = "cpu";
			reg = <0>;
			riscv,isa = "rv32im_zicsr_zifencei";
			status = "okay";
		};
	};

	soc {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "litex,vexriscv";
		ranges;

		ctrl0: soc_controller@e0000000 {
			compatible = "litex,soc-controller";
			reg = <0xe0000000 0x4
			       0xe0000004 0x4
			       0xe0000008 0x4>;
			reg-names = "reset",
				    "scratch",
				    "bus_errors";
		};

		intc0: interrupt-controller@bc0 {
			compatible = "litex,vexriscv-intc0";
			#address-cells = <0>;
			#interrupt-cells = <2>;
			interrupt-controller;
			reg = <0xbc0 0x4 0xfc0 0x4>;
			reg-names = "irq_mask", "irq_pending";
			riscv,max-priority = <7>;
		};

		uart0: serial@e0001800 {
			compatible = "litex,uart";
			interrupt-parent = <&intc0>;
			interrupts = <2 10>;
			reg = <0xe0001800 0x4
			       0xe0001804 0x4
			       0xe0001808 0x4
			       0xe000180c 0x4
			       0xe0001810 0x4
			       0xe0001814 0x4
			       0xe0001818 0x4
			       0xe000181c 0x4>;
			reg-names = "rxtx",
				    "txfull",
				    "rxempty",
				    "ev_status",
				    "ev_pending",
				    "ev_enable",
				    "txempty",
				    "rxfull";
			status = "disabled";
		};

		spi0: spi@e0002000 {
			compatible = "litex,spi";
			reg = <0xe0002000 0x4
			       0xe0002004 0x4
			       0xe0002008 0x4
			       0xe000200c 0x4
			       0xe0002010 0x4
			       0xe0002014 0x4>;
			reg-names = "control",
				    "status",
				    "mosi",
				    "miso",
				    "cs",
				    "loopback";
			status = "disabled";
			#address-cells = <1>;
			#size-cells = <0>;
		};

		spi1: spi@e000c000 {
			compatible = "litex,spi-litespi";
			interrupt-parent = <&intc0>;
			reg = <0xe000c000 0x4>,
			      <0xe000c004 0x4>,
			      <0xe000c008 0x4>,
			      <0xe000c00c 0x4>,
			      <0xe000c010 0x4>,
			      <0xe000c014 0x4>,
			      <0xe000c018 0x4>,
			      <0xe000c01c 0x4>,
			      <0xe000c020 0x4>,
			      <0x60000000 0x1000000>;
			reg-names = "phy_clk_divisor",
				    "mmap_dummy_bits",
				    "master_cs",
				    "master_phyconfig",
				    "master_rxtx",
				    "master_status",
				    "master_ev_status",
				    "master_ev_pending",
				    "master_ev_enable",
				    "flash_mmap";
			interrupts = <9 0>;
			#address-cells = <1>;
			#size-cells = <0>;

			spiflash0: flash@0 {
				compatible = "jedec,spi-nor";
				reg = <0>;
				spi-max-frequency = <10000000>;
			};
		};

		timer0: timer@e0002800 {
			compatible = "litex,timer0";
			interrupt-parent = <&intc0>;
			interrupts = <1 0>;
			reg = <0xe0002800 0x4
			       0xe0002804 0x4
			       0xe0002808 0x4
			       0xe000280c 0x4
			       0xe0002810 0x4
			       0xe0002814 0x4
			       0xe0002818 0x4
			       0xe000281c 0x4
			       0xe0002820 0x4
			       0xe0002824 0x8>;
			reg-names = "load",
				    "reload",
				    "en",
				    "update_value",
				    "value",
				    "ev_status",
				    "ev_pending",
				    "ev_enable",
				    "uptime_latch",
				    "uptime_cycles";
			status = "disabled";
		};

		wdt0: watchdog@e000d000 {
			compatible = "litex,watchdog";
			interrupt-parent = <&intc0>;
			reg = <0xe000d000 0x4>,
			      <0xe000d004 0x4>,
			      <0xe000d008 0x4>,
			      <0xe000d00c 0x4>,
			      <0xe000d010 0x4>,
			      <0xe000d014 0x4>;
			reg-names = "control",
				    "cycles",
				    "remaining",
				    "ev_status",
				    "ev_pending",
				    "ev_enable";
			interrupts = <8 15>;
		};

		mdio0: mdio@e0008000 {
			compatible = "litex,liteeth-mdio";
			reg = <0xe0008000 0x4>,
			      <0xe0008004 0x4>,
			      <0xe0008008 0x4>;
			reg-names = "crg_reset",
				    "mdio_w",
				    "mdio_r";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";

			phy0: ethernet-phy@1 {
				compatible = "ethernet-phy";
				reg = <1>;
			};
		};

		eth0: ethernet@e0009800 {
			compatible = "litex,liteeth";
			interrupt-parent = <&intc0>;
			interrupts = <3 0>;
			reg = <0xe0009800 0x4
			       0xe0009804 0x4
			       0xe0009808 0x4
			       0xe000980c 0x4
			       0xe0009810 0x4
			       0xe0009814 0x4
			       0xe0009818 0x4
			       0xe000981c 0x4
			       0xe0009820 0x4
			       0xe0009824 0x4
			       0xe0009828 0x4
			       0xe000982c 0x4
			       0xe0009830 0x4
			       0xe0009834 0x4
			       0xb0000000 0x2000>;
			local-mac-address = [10 e2 d5 00 00 02];
			reg-names = "rx_slot",
				    "rx_length",
				    "rx_errors",
				    "rx_ev_status",
				    "rx_ev_pending",
				    "rx_ev_enable",
				    "tx_start",
				    "tx_ready",
				    "tx_level",
				    "tx_slot",
				    "tx_length",
				    "tx_ev_status",
				    "tx_ev_pending",
				    "tx_ev_enable",
				    "buffers";
			phy-handle = <&phy0>;
			status = "disabled";
		};

		dna0: dna@e0003800 {
			compatible = "litex,dna0";
			/* DNA data is 57-bits long,
			 * so it requires 8 bytes.
			 * In LiteX each 32-bit register holds
			 * only a single byte of meaningful data,
			 * hence 8 registers.
			 */
			reg = <0xe0003800 0x20>;
			reg-names = "mem";
			status = "disabled";
		};

		i2c0: i2c@e0005000 {
			compatible = "litex,i2c";
			reg = <0xe0005000 0x4 0xe0005004 0x4>;
			reg-names = "write", "read";
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c1: i2c@e000d800 {
			compatible = "litex,litei2c";
			interrupt-parent = <&intc0>;
			reg = <0xe000d800 0x4>,
			      <0xe000d804 0x4>,
			      <0xe000d808 0x4>,
			      <0xe000d80c 0x4>,
			      <0xe000d810 0x4>,
			      <0xe000d814 0x4>,
			      <0xe000d818 0x4>,
			      <0xe000d81c 0x4>,
			      <0xe000d820 0x4>;
			reg-names = "phy_speed_mode",
				    "master_active",
				    "master_settings",
				    "master_addr",
				    "master_rxtx",
				    "master_status",
				    "master_ev_status",
				    "master_ev_pending",
				    "master_ev_enable";
			interrupts = <10 0>;
			clock-frequency = <I2C_BITRATE_STANDARD>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		gpio_out: gpio@e0005800 {
			compatible = "litex,gpio";
			reg = <0xe0005800 0x4>;
			reg-names = "control";
			ngpios = <4>;
			port-is-output;
			status = "disabled";
			gpio-controller;
			#gpio-cells = <2>;
		};

		gpio_in: gpio@e0006000 {
			compatible = "litex,gpio";
			reg = <0xe0006000 0x4
			       0xe0006004 0x4
			       0xe0006008 0x4
			       0xe0006010 0x4
			       0xe0006014 0x4>;
			interrupt-parent = <&intc0>;
			interrupts = <4 2>;
			reg-names = "base",
				    "irq_mode",
				    "irq_edge",
				    "irq_pend",
				    "irq_en";
			ngpios = <4>;
			status = "disabled";
			gpio-controller;
			#gpio-cells = <2>;
		};

		prbs0: prbs@e0006800 {
			compatible = "litex,prbs";
			reg = <0xe0006800 0x4>;
			reg-names = "status";
			status = "disabled";
		};

		pwm0: pwm@e0007000 {
			compatible = "litex,pwm";
			reg = <0xe0007000 0x4 0xe0007004 0x10 0xe0007014 0x10>;
			reg-names = "enable", "width", "period";
			status = "disabled";
			#pwm-cells = <2>;
		};

		i2s_rx: i2s_rx@e000a800 {
			compatible = "litex,i2s";
			reg = <0xe000a800 0x4
			       0xe000a804 0x4
			       0xe000a808 0x4
			       0xe000a80c 0x4
			       0xe000a810 0x4
			       0xe000a814 0x4
			       0xb1000000 0x40000>;
			interrupt-parent = <&intc0>;
			interrupts = <6 2>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg-names = "ev_status",
				    "ev_pending",
				    "ev_enable",
				    "rx_ctl",
				    "rx_stat",
				    "rx_conf",
				    "fifo";
			fifo-depth = <256>;
			status = "disabled";
		};

		i2s_tx: i2s_tx@e000b000 {
			compatible = "litex,i2s";
			reg = <0xe000b000 0x4
			       0xe000b004 0x4
			       0xe000b008 0x4
			       0xe000b00c 0x4
			       0xe000b010 0x4
			       0xe000b014 0x4
			       0xb2000000 0x40000>;
			interrupt-parent = <&intc0>;
			interrupts = <7 2>;
			#address-cells = <1>;
			#size-cells = <0>;
			reg-names = "ev_status",
				    "ev_pending",
				    "ev_enable",
				    "tx_ctl",
				    "tx_stat",
				    "tx_conf",
				    "fifo";
			fifo-depth = <256>;
			status = "disabled";
		};

		clock-outputs {
			#address-cells = <1>;
			#size-cells = <0>;

			clk0: clock-controller@0 {
				#clock-cells = <1>;
				reg = <0>;
				compatible = "litex,clkout";
				clock-output-names = "CLK_0";
				litex,clock-frequency = <11289600>;
				litex,clock-phase = <0>;
				litex,clock-duty-num = <1>;
				litex,clock-duty-den = <2>;
				litex,clock-margin = <1>;
				litex,clock-margin-exp = <2>;
				status = "disabled";
			};

			clk1: clock-controller@1 {
				#clock-cells = <1>;
				reg = <1>;
				compatible = "litex,clkout";
				clock-output-names = "CLK_1";
				litex,clock-frequency = <22579200>;
				litex,clock-phase = <0>;
				litex,clock-duty-num = <1>;
				litex,clock-duty-den = <2>;
				litex,clock-margin = <1>;
				litex,clock-margin-exp = <2>;
				status = "disabled";
			};
		};

		clock0: clock@e0004800 {
			compatible = "litex,clk";
			reg = <0xe0004800 0x4
			       0xe0004804 0x4
			       0xe0004808 0x4
			       0xe000480c 0x4
			       0xe0004810 0x4
			       0xe0004814 0x4
			       0xe0004818 0x4
			       0xe000481c 0x4>;
			reg-names = "drp_reset",
				    "drp_locked",
				    "drp_read",
				    "drp_write",
				    "drp_drdy",
				    "drp_adr",
				    "drp_dat_w",
				    "drp_dat_r";
			#clock-cells = <1>;
			clocks = <&clk0 0>, <&clk1 1>;
			clock-output-names = "CLK_0", "CLK_1";
			litex,lock-timeout = <10>;
			litex,drdy-timeout = <10>;
			litex,divclk-divide-min = <1>;
			litex,divclk-divide-max = <107>;
			litex,clkfbout-mult-min = <2>;
			litex,clkfbout-mult-max = <65>;
			litex,vco-freq-min = <600000000>;
			litex,vco-freq-max = <1200000000>;
			litex,clkout-divide-min = <1>;
			litex,clkout-divide-max = <126>;
			litex,vco-margin = <0>;
			status = "disabled";
		};
	};
};