#
# Copyright (c) 2020 Siddharth Chandrasekaran <siddharth@embedjournal.com>
#
# SPDX-License-Identifier: Apache-2.0
#

# OSDP_NUM_CONNECTED_PD is used in CP mode. It is a constant set to 1 when
# operating as a PD.
config OSDP_NUM_CONNECTED_PD
	int
	default 1
	help
	  In PD mode, number of connected PDs is is always 1 and cannot
	  be configured.

config OSDP_PD_COMMAND_QUEUE_SIZE
	int "OSDP Peripheral Device command queue size"
	default 16
	help
	  The number of commands that can be queued to a given PD. In CP mode,
	  the queue size is multiplied by number of connected PD so this can grow
	  very quickly.

config OSDP_PD_ADDRESS
	int "Peripheral Device Address"
	default 1
	range 1 126
	help
	  The 7 least significant bits represent the address of the PD to which
	  the message is directed, or the address of the PD sending the reply.
	  Address 0x7F is reserved as a broadcast address to which all PDs would
	  respond.

if OSDP_SC_ENABLED

config OSDP_PD_SCBK
	string "Secure Channel Base Key (SCBK)"
	default "NONE"
	help
	  Hexadecimal string representation of the the 16 byte OSDP PD Secure
	  Channel Base Key. When this field is sent to "NONE", the PD is set to
	  "Install Mode". In this mode, the PD would allow a CP to setup a secure
	  channel with default SCBK. Once as secure channel is active with the
	  default key, the CP can send a KEYSET command to set new keys to the PD.
	  It is up to the user to make sure that the PD enters the "Install Mode"
	  only during provisioning time (controlled environment).

endif # OSDP_SC_ENABLED

menu "Peripheral Device ID Information"

config OSDP_PD_ID_VENDOR_CODE
	hex "PD Vendor Code"
	default 0x001A2B3C
	range 0 0x00FFFFFF
	help
	  IEEE assigned OUI. Least 24 bits are valid.

config OSDP_PD_ID_MODEL
	int "PD Product Model Number"
	default 1
	range 0 255
	help
	  Manufacturer's model number. Least 8 bits are valid.

config OSDP_PD_ID_VERSION
	int "PD Product Version"
	default 1
	range 0 255
	help
	  Manufacturer's version of this product. Least 8 bits are valid.

config OSDP_PD_ID_SERIAL_NUMBER
	hex "PD Serial Number"
	default 0xCAFEBABE
	range 0 0xFFFFFFFF
	help
	  A 4-byte serial number for the PD.

config OSDP_PD_ID_FIRMWARE_VERSION
	hex "PD Firmware Version"
	default 0x00010100
	range 0 0x00FFFFFF
	help
	  Firmware revision code.
	    - Bit 0-7  : build version number;
	    - Bit 8-15 : minor version number;
	    - Bit 16-23: major version number;

endmenu # "PD ID Information"

menu "OSDP PD Capabilities"

menu "Contact Status Monitoring"

config OSDP_PD_CAP_CONTACT_STATUS_MONITORING_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 4
	help
	  Possible values:
	  - 01: PD monitors and reports the state of the circuit without any
	  supervision. The PD encodes the circuit status per its default
	  interpretation of contact state to active/inactive status.
	  - 02: Like 01, plus: The PD accepts configuration of the encoding of the
	  open/closed circuit status to the reported active/inactive status. (User
	  may configure each circuit as "normally closed" or "normally open".)
	  - 03: Like 02, plus: PD supports supervised monitoring. The operating mode
	  for each circuit is determined by configuration settings.
	  - 04: Like 03, plus: the PD supports custom End-Of-Line settings within
	  the Manufacturer's guidelines.

config OSDP_PD_CAP_CONTACT_STATUS_MONITORING_NUM_ITEMS
	int "Number of items"
	default 0
	help
	  The number of Inputs

endmenu # "Contact Status Monitoring"

menu "Output Control"

config OSDP_PD_CAP_OUTPUT_CONTROL_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 4
	help
	  Possible values:
	  - 01: The PD is able to activate and deactivate the Output per direct
	  command from the CP.
	  - 02: Like 01, plus: The PD is able to accept configuration of the Output
	  driver to set the inactive state of the Output. The typical state of an
	  inactive Output is the state of the Output when no power is applied to the
	  PD and the output device (relay) is not energized. The inverted drive
	  setting causes the PD to energize the Output during the inactive state and
	  de-energize the Output during the active state. This feature allows the
	  support of "fail-safe/fail-secure" operating modes.
	  - 03: Like 01, plus: The PD is able to accept timed commands to the
	  Output. A timed command specifies the state of the Output for the
	  specified duration.
	  - 04: Like 02 and 03 - normal/inverted drive and timed operation.

config OSDP_PD_CAP_OUTPUT_CONTROL_NUM_ITEMS
	int "Number of items"
	default 0
	help
	  The number of Outputs.

endmenu # "Output Control"

menu "LED Control"

config OSDP_PD_CAP_READER_LED_CONTROL_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 4
	help
	  Possible values:
	  - 01: the PD support on/off control only
	  - 02: the PD supports timed commands
	  - 03: like 02, plus bi-color LEDs
	  - 04: like 02, plus tri-color LEDs

config OSDP_PD_CAP_READER_LED_CONTROL_NUM_ITEMS
	int "Number of items"
	default 0
	help
	  The number of LEDs per reader.

endmenu # "LED Control"

menu "Audible Output"

config OSDP_PD_CAP_READER_AUDIBLE_OUTPUT_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 2
	help
	  Possible values:
	  - 01: the PD support on/off control only
	  - 02: the PD supports timed commands

config OSDP_PD_CAP_READER_AUDIBLE_OUTPUT_NUM_ITEMS
	int "Number of items"
	default 0
	help
	  The number of audible annunciators per reader

endmenu # "Audible Output"

menu "Text Output"

config OSDP_PD_CAP_READER_TEXT_OUTPUT_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 4
	help
	  Possible values:
	  - 00: The PD has no text display support
	  - 01: The PD supports 1 row of 16 characters
	  - 02: the PD supports 2 rows of 16 characters
	  - 03: the PD supports 4 rows of 16 characters
	  - 04: TBD.

config OSDP_PD_CAP_READER_TEXT_OUTPUT_NUM_ITEMS
	int "Number of items"
	default 0
	help
	  Number of textual displays per reader

endmenu # "Text Output"

menu "Card Data Format"

config OSDP_PD_CAP_CARD_DATA_FORMAT_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 3
	help
	  Possible values:
	  - 01: the PD sends card data to the CP as array of bits, not exceeding
	  1024 bits.
	  - 02: the PD sends card data to the CP as array of BCD characters, not
	  exceeding 256 characters.
	  - 03: the PD can send card data to the CP as array of bits, or as an
	  array of BCD characters.

endmenu # "Card Data Format"

menu "Time Keeping"

config OSDP_PD_CAP_TIME_KEEPING_COMP_LEVEL
	int "Compliance Level"
	default 0
	range 0 2
	help
	  Possible values:
	  - 00: The PD does not support time/date functionality
	  - 01: The PD understands time/date settings per Command osdp_TDSET
	  - 02: The PD is able to locally update the time and date

endmenu # "Time Keeping"

endmenu # "OSDP PD Capabilities"