diff --git a/drivers/espi/Kconfig.it8xxx2 b/drivers/espi/Kconfig.it8xxx2
index e018f86..6c19eb2 100644
--- a/drivers/espi/Kconfig.it8xxx2
+++ b/drivers/espi/Kconfig.it8xxx2
@@ -127,4 +127,19 @@
 	  With this option enabled, EC will send IRQ12 signal to host when the
 	  KBC mouse output buffer is full.
 
+# On IT8xxx2 series, this configuration option has limitation:
+# Port 80 and 81 I/O cycles share the same interrupt source and there is no
+# status bit to indicate which cycle triggered the interrupt and data registers
+# of these two ports are read only. Hence EC have to read these two data
+# registers at the same time in the ISR.
+# It means that the Host must alwasy write 2 bytes of data to port 80 otherwise
+# port 81 data will not be updated.
+config ESPI_IT8XXX2_PORT_81_CYCLE
+	bool "EC accepts 0x81 I/O cycle from eSPI transaction"
+	depends on ESPI_PERIPHERAL_DEBUG_PORT_80
+	help
+	  With this option enabled, EC will accept 0x81 I/O cycle from the Host.
+	  This allows EC to accept 2 bytes of port 80 data written from the Host.
+	  (e.g. using iotools: iotools io_write16 0x80 0x1234)
+
 endif #ESPI_IT8XXX2
diff --git a/drivers/espi/espi_it8xxx2.c b/drivers/espi/espi_it8xxx2.c
index bd0d83c..f0510c7f 100644
--- a/drivers/espi/espi_it8xxx2.c
+++ b/drivers/espi/espi_it8xxx2.c
@@ -517,7 +517,11 @@
 		ESPI_PERIPHERAL_NODATA
 	};
 
-	evt.evt_data = gctrl->GCTRL_P80HDR;
+	if (IS_ENABLED(CONFIG_ESPI_IT8XXX2_PORT_81_CYCLE)) {
+		evt.evt_data = gctrl->GCTRL_P80HDR | (gctrl->GCTRL_P81HDR << 8);
+	} else {
+		evt.evt_data = gctrl->GCTRL_P80HDR;
+	}
 	/* Write 1 to clear this bit */
 	gctrl->GCTRL_P80H81HSR |= BIT(0);
 
@@ -529,8 +533,13 @@
 	ARG_UNUSED(dev);
 	struct gctrl_it8xxx2_regs *const gctrl = ESPI_IT8XXX2_GET_GCTRL_BASE;
 
-	/* Accept Port 80h Cycle */
-	gctrl->GCTRL_SPCTRL1 |= IT8XXX2_GCTRL_ACP80;
+	/* Accept Port 80h (and 81h) Cycle */
+	if (IS_ENABLED(CONFIG_ESPI_IT8XXX2_PORT_81_CYCLE)) {
+		gctrl->GCTRL_SPCTRL1 |=
+			(IT8XXX2_GCTRL_ACP80 | IT8XXX2_GCTRL_ACP81);
+	} else {
+		gctrl->GCTRL_SPCTRL1 |= IT8XXX2_GCTRL_ACP80;
+	}
 	IRQ_CONNECT(IT8XXX2_PORT_80_IRQ, 0, port80_it8xxx2_isr,
 			DEVICE_DT_INST_GET(0), 0);
 	irq_enable(IT8XXX2_PORT_80_IRQ);
diff --git a/soc/ite/ec/common/chip_chipregs.h b/soc/ite/ec/common/chip_chipregs.h
index 71176c3..c585271 100644
--- a/soc/ite/ec/common/chip_chipregs.h
+++ b/soc/ite/ec/common/chip_chipregs.h
@@ -1661,6 +1661,8 @@
 #define IT8XXX2_GCTRL_ILM0_ENABLE	BIT(0)
 /* Accept Port 80h Cycle */
 #define IT8XXX2_GCTRL_ACP80		BIT(6)
+/* Accept Port 81h Cycle */
+#define IT8XXX2_GCTRL_ACP81		BIT(3)
 /* USB Debug Enable */
 #define IT8XXX2_GCTRL_MCCR_USB_EN	BIT(7)
 /* USB Pad Power-On Enable */