/*
 * Copyright (c) 2024 BayLibre
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;
#include <st/f4/stm32f469Xi.dtsi>
#include <st/f4/stm32f469nihx-pinctrl.dtsi>
#include "arduino_r3_connector.dtsi"

/ {
	model = "Analog Devices Inc. SDP-K1 board";
	compatible = "adi,sdp-k1";

	chosen {
		zephyr,console = &uart5;
		zephyr,shell-uart = &uart5;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
		zephyr,ccm = &ccm0;
	};

	leds {
		compatible = "gpio-leds";
		status_led: led_ds3 {
			gpios = <&gpiok 4 GPIO_ACTIVE_HIGH>;
			label = "Status DS3";
		};
		green_led_1: led_ds4 {
			gpios = <&gpiok 5 GPIO_ACTIVE_HIGH>;
			label = "User LD1";
		};
		orange_led_2: led_ds5 {
			gpios = <&gpiok 6 GPIO_ACTIVE_HIGH>;
			label = "User LD2";
		};
		red_led_3: led_ds6 {
			gpios = <&gpiok 7 GPIO_ACTIVE_HIGH>;
			label = "User LD3";
		};
	};

	otghs_ulpi_phy: otghs_ulpis_phy {
		compatible = "usb-ulpi-phy";
		reset-gpios = <&gpiod 7 (GPIO_ACTIVE_LOW)>;
		#phy-cells = <0>;
	};

	aliases {
		led0 = &status_led;
	};
};

&clk_lsi {
	status = "okay";
};

&clk_hse {
	clock-frequency = <DT_FREQ_M(8)>;
	status = "okay";
};

&pll {
	div-m = <8>;
	mul-n = <336>;
	div-p = <2>;
	div-q = <7>;
	clocks = <&clk_hse>;
	status = "okay";
};

&rcc {
	clocks = <&pll>;
	clock-frequency = <DT_FREQ_M(168)>;
	ahb-prescaler = <1>;
	apb1-prescaler = <4>;
	apb2-prescaler = <2>;
};

&uart5 {
	pinctrl-0 = <&uart5_tx_pc12 &uart5_rx_pd2>;
	pinctrl-names = "default";
	current-speed = <115200>;
	status = "okay";
};

zephyr_udc0: &usbotg_hs {
	pinctrl-0 = <&usb_otg_hs_ulpi_ck_pa5
		     &usb_otg_hs_ulpi_d0_pa3
		     &usb_otg_hs_ulpi_d1_pb0
		     &usb_otg_hs_ulpi_d2_pb1
		     &usb_otg_hs_ulpi_d3_pb10
		     &usb_otg_hs_ulpi_d4_pb11
		     &usb_otg_hs_ulpi_d5_pb12
		     &usb_otg_hs_ulpi_d6_pb13
		     &usb_otg_hs_ulpi_d7_pb5
		     &usb_otg_hs_ulpi_stp_pc0
		     &usb_otg_hs_ulpi_dir_pc2
		     &usb_otg_hs_ulpi_nxt_pc3>;
	pinctrl-names = "default";
	maximum-speed = "high-speed";
	/* Enable OTGHSULPIEN rather than OTGHSEN */
	clocks = <&rcc STM32_CLOCK_BUS_AHB1 0x60000000>,
		 <&rcc STM32_SRC_PLL_Q NO_SEL>;
	phys = <&otghs_ulpi_phy>;
	status = "okay";
};