dts/bindings/gpio/adi,max14916-gpio.yaml

# Copyright (c) 2024 Analog Devices Inc.
# Copyright (c) 2024 BayLibre SAS
# SPDX-License-Identifier: Apache-2.0

description: ADI  MAX14916 is octal industrial output with advanced diagnostics

compatible: "adi,max14916-gpio"

properties:
  "#gpio-cells":
    const: 2
  ngpios:
    type: int
    required: true
    const: 8
    description: Number of gpios supported
  drdy-gpios:
    description: |
      High-Side Open-Drain Output. READY is passive low when the internal
      logic supply is higher than the UVLO threshold, indicating that the
      registers have adequate supply voltage.
    type: phandle-array
  fault-gpios:
    description: |
      Fault pin indicates when there is Fault state in either FAULT1 or FAULT2
      bothe of which are cleaned on read once problem is not persistent
    type: phandle-array
  sync-gpios:
    description: |
      Latch the data so it could be read (partially duplicate CS)
    type: phandle-array
  en-gpios:
    description: |
      DOI Enable Pin. Drive the EN pin high to enable the DOI_ outputs.
      Drive EN low to disable/three-state all DOI_ outputs.
    type: phandle-array
  crc-en:
    description: |
      Notify driver if crc pin is enabled.
    type: boolean
  spi-addr:
    type: int
    default: 0
    required: true
    enum:
      - 0
      - 1
      - 2
      - 3
    description: |
      On MAX14906PMB module default address is 0 (A0-LOW, A1-LOW)
      Selectable device address, configurable from A0 and A1
  ow-on-en:
    type: array
    default: [0, 0, 0, 0, 0, 0, 0, 0]
    description: |
      Default values are from documentation.
      Enable or disable open-wire-on functionality per channel.
      - 0 mean disable
      - 1 mean enable
      channels indentation start from CH0...CH7
  ow-off-en:
    type: array
    default: [0, 0, 0, 0, 0, 0, 0, 0]
    description: |
      Default values are from documentation.
      Enable or disable open-wire-off functionality per channel.
      - 0 mean disable
      - 1 mean enable
      channels indentation start from CH0...CH7
  sh-vdd-en:
    type: array
    default: [0, 0, 0, 0, 0, 0, 0, 0]
    description: |
      Default values are from documentation.
      ShVddEN - Short to VDD enable
      Enable or disable short to VDD functionality per channel.
      - 0 mean disable
      - 1 mean enable
      channels indentation start from CH0...CH3
  fled-set:
    type: boolean
    description: |
      Internal fault diagnostics include (if enabled): SafeDemagF_, SHVDD_,
      VDDOV_, OWOff_, AboveVDD_, CL_, OVL_, VDDOKFault_.
  sled-set:
    type: boolean
    description: |
      Enable status LEDs
  fled-stretch:
    type: int
    default: 0
    enum:
      - 0
      - 1
      - 2
      - 3
    description: |
      Default values are from documentation.
      Set minimum on time for FLEDs in case of fault
      0 - Disable minimum fault LED (FLED) on-time
      1 - Minimum fault LED (FLED) on-time = 1s (typ)
      2 - Minimum fault LED (FLED) on-time = 2s (typ)
      3 - Minimum fault LED (FLED) on-time = 3s (typ)
  ffilter-en:
    type: boolean
    description: |
      When the fault LEDs (FLEDs) are controlled internally (FLEDSet = 0), open-
      wire and short-to-V DD diagnostics always use filtering and cannot be disabled
      by the FFilterEn bit.
  filter-long:
    type: boolean
    description: |
      false: To select regular blanking time (4ms, typ) for diagnostic fault bits, OWOff_
             and SHVDD_
      true:  To select long blanking time (8ms, typ) for diagnostic fault bits, OWOff_
             and SHVDD_
  flatch-en:
    type: boolean
    description: |
      false: Disable latching of diagnostic fault bits in the OvrLdChF, OpnWirChF, and
             ShtVDDChF registers
      true:  Enable latching of diagnostic fault bits in the OvrLdChF, OpnWirChF, and
             ShtVDDChF registers
  led-cur-lim:
    type: boolean
    description: |
      false: Disable fault LEDs (FLEDs) signaling current limit
      true:  Enable fault LEDs (FLEDs) signaling current limit
  vdd-on-thr:
    type: boolean
    description: |
      Enable higher voltage thresholds for VDD and VDD_ undervoltage monitoring
  synch-wd-en:
    type: boolean
    description: |
      The SYNCH watchdog timeout is defined by the WDTo[1:0] bits if the SPI
      watchdog is enabled. When WDTo[1:0] = 00 (SPI watchdog disabled), the
      SYNCH watchdog timeout is 600ms (typ) if enabled.
  sht-vdd-thr:
    type: int
    default: 0
    enum:
      - 0
      - 1
      - 2
      - 3
    description: |
      Default values are from documentation.
      Set threshold voltage for short-to-V DD detection
      0: Set threshold voltage for short-to-VDD detection to 9V (typ)
      1: Set threshold voltage for short-to-VDD detection to 10V (typ)
      2: Set threshold voltage for short-to-VDD detection to 12V (typ)
      3: Set threshold voltage for short-to-VDD detection to 14V (typ)
  ow-off-cs:
    type: int
    default: 0
    enum:
      - 0
      - 1
      - 2
      - 3
    description: |
      Default values are from documentation.
      Set the pullup current for open-wire and short-to-VDD detection
      0: Set open-wire and short-to-VDD detection current to 60μA (typ)
      1: Set open-wire and short-to-VDD detection current to 100μA (typ)
      2: Set open-wire and short-to-VDD detection current to 300μA (typ)
      3: Set open-wire and short-to-VDD detection current to 600μA (typ)
  wd-to:
    type: int
    default: 0
    enum:
      - 0
      - 1
      - 2
      - 3
    description: |
      Default values are from documentation.
      SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout
      0: Disable SPI Watchdog Status and SPI Watchdog Timeout
      1: Enable SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout to 200ms (typ)
      2: Enable SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout to 600ms (typ)
      3: Enable SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout to 1.2s (typ)

gpio-cells:
  - pin
  - flags

include: [gpio-controller.yaml, spi-device.yaml]