# Copyright (c) 2024 STMicroelectronics
# SPDX-License-Identifier: Apache-2.0

description: STM32WB0 power controller

compatible: "st,stm32wb0-pwr"

include: "st,stm32-pwr.yaml"

properties:
  smps-mode:
    type: string
    required: true
    description: |
      SMPS mode selection

      OFF:
        - SMPS converter disabled
        - LDOs supply voltage: VDD

      WARNING: The SMPS must not be disabled on board using the
      'SMPS supply configuration', so this mode should NEVER be
      selected on these boards. Only use this mode if your board
      is using the 'NOSMPS supply configuration'.

      Refer to RM0505 §5.5 "SMPS step down regulator" for details.

      PRECHARGE: (also called BYPASS)
        - SMPS converter enabled - clock disabled
        - LDOs supply voltage: VDD (though SMPS)
          - Current supplied to LDOs can be limited
            (feature only supported on STM32WB05 / STM32WB09)

      RUN: (also called ON)
        - SMPS converter enabled - clock enabled
        - LDOs supply voltage: regulated SMPS output
          - Target output voltage can be programmed
    enum:
      - "OFF"
      - "PRECHARGE"
      - "RUN"

  smps-bom:
    type: int
    description: |
      SMPS L/C BOM selection

      Indicates which L/C BOM is present on the board:
        1: 1.5µH inductance, 2.2µF output capacitance
        2: 2.2µH inductance, 4.7µF output capacitance
        3: 10µH inductance, 4.7µF output capacitance
      Refer to RM0505 §5.5 for more details about L/C BOM.

      This property is required if `smps-mode` is not "OFF".
    enum:
      - 1
      - 2
      - 3

  smps-clock-prescaler:
    type: int
    default: 4
    description: |
      SMPS clock prescaler factor

      The SMPS clock, CLK_SMPS, comes from a 16 MHz source that
      goes through one of two prescalers, with a respective
      division factor of 2 and 4. This property selects which
      prescaler should be used.

      Setting this property to 2 results in CLK_SMPS = 8 MHz.
      Setting this property to 4 results in CLK_SMPS = 4 MHz.

      All features of the SMPS can be used regardless of which
      prescaler has been chosen. Since a slower clock results
      in less power consumption, this property defaults to 4.

      This property is only used if `smps-mode` is not "OFF".
    enum:
      - 2
      - 4

  smps-lp-floating:
    type: boolean
    description: |
      Floating SMPS output in low-power state

      If this property is set, the SMPS output pin (VFBSD)
      is left floating when the SoC is in low-power state.

      If this property is not set, the SMPS is placed in
      PRECHARGE mode when the SoC is in low-power state.
      (i.e., VFBSD voltage is equal to VDD)

  smps-current-limit:
    type: string
    default: "20"
    description: |
      SMPS output current limit (in mA)

      The default value of 20 mA corresponds to the maximal
      output current allowed for the SMPS, and is also equal
      to the hardware reset configuration.

      On STM32WB06 and STM32WB07, this property is ignored as
      the output current limitation feature is not available.

      This property is only used if `smps-mode` is "PRECHARGE".
    enum:
      - "2_5"
      - "5"
      - "10"
      - "20"

  smps-output-voltage:
    type: string
    default: "1V40"
    description: |
      SMPS regulated output voltage

      The default value corresponds to the hardware reset
      configuration of 1.40V regulated output.

      This property is only used if `smps-mode` is "RUN".
    enum:
      - "1V20"
      - "1V25"
      - "1V30"
      - "1V35"
      - "1V40"
      - "1V45"
      - "1V50"
      - "1V55"
      - "1V60"
      - "1V65"
      - "1V70"
      - "1V75"
      - "1V80"
      - "1V85"
      - "1V90"
      - "1V95"