| /* |
| * Copyright 2020,2023 NXP |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #define DT_DRV_COMPAT nxp_imx_flexspi_nor |
| |
| #include <zephyr/drivers/flash.h> |
| #include <zephyr/irq.h> |
| #include <zephyr/logging/log.h> |
| #include <zephyr/sys/util.h> |
| #include "spi_nor.h" |
| #include "memc_mcux_flexspi.h" |
| |
| #ifdef CONFIG_HAS_MCUX_CACHE |
| #include <fsl_cache.h> |
| #endif |
| |
| #define NOR_WRITE_SIZE 1 |
| #define NOR_ERASE_VALUE 0xff |
| |
| #ifdef CONFIG_FLASH_MCUX_FLEXSPI_NOR_WRITE_BUFFER |
| static uint8_t nor_write_buf[SPI_NOR_PAGE_SIZE]; |
| #endif |
| |
| /* |
| * NOTE: If CONFIG_FLASH_MCUX_FLEXSPI_XIP is selected, Any external functions |
| * called while interacting with the flexspi MUST be relocated to SRAM or ITCM |
| * at runtime, so that the chip does not access the flexspi to read program |
| * instructions while it is being written to |
| * |
| * Additionally, no data used by this driver should be stored in flash. |
| */ |
| #if defined(CONFIG_FLASH_MCUX_FLEXSPI_XIP) && (CONFIG_FLASH_LOG_LEVEL > 0) |
| #warning "Enabling flash driver logging and XIP mode simultaneously can cause \ |
| read-while-write hazards. This configuration is not recommended." |
| #endif |
| |
| LOG_MODULE_REGISTER(flash_flexspi_nor, CONFIG_FLASH_LOG_LEVEL); |
| |
| enum { |
| /* Instructions matching with XIP layout */ |
| READ_FAST_QUAD_OUTPUT, |
| READ_FAST_OUTPUT, |
| READ_NORMAL_OUTPUT, |
| READ_STATUS, |
| WRITE_ENABLE, |
| ERASE_SECTOR, |
| ERASE_BLOCK, |
| PAGE_PROGRAM_INPUT, |
| PAGE_PROGRAM_QUAD_INPUT, |
| READ_ID, |
| WRITE_STATUS_REG, |
| ENTER_QPI, |
| EXIT_QPI, |
| READ_STATUS_REG, |
| ERASE_CHIP, |
| }; |
| |
| /* Device variables used in critical sections should be in this structure */ |
| struct flash_flexspi_nor_data { |
| const struct device *controller; |
| flexspi_device_config_t config; |
| flexspi_port_t port; |
| struct flash_pages_layout layout; |
| struct flash_parameters flash_parameters; |
| }; |
| |
| static const uint32_t flash_flexspi_nor_lut[][4] = { |
| [READ_ID] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_RDID, |
| kFLEXSPI_Command_READ_SDR, kFLEXSPI_1PAD, 0x04), |
| }, |
| |
| [READ_STATUS_REG] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_RDSR, |
| kFLEXSPI_Command_READ_SDR, kFLEXSPI_1PAD, 0x04), |
| }, |
| |
| [WRITE_STATUS_REG] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_WRSR, |
| kFLEXSPI_Command_WRITE_SDR, kFLEXSPI_1PAD, 0x04), |
| }, |
| |
| [WRITE_ENABLE] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_WREN, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| |
| [ERASE_SECTOR] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_SE, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| }, |
| |
| [ERASE_BLOCK] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_BE, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| }, |
| |
| [ERASE_CHIP] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_CE, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| |
| [READ_FAST_QUAD_OUTPUT] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, 0x6B, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_DUMMY_SDR, kFLEXSPI_4PAD, 0x08, |
| kFLEXSPI_Command_READ_SDR, kFLEXSPI_4PAD, 0x04), |
| }, |
| |
| [READ_FAST_OUTPUT] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, 0x0B, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_DUMMY_SDR, kFLEXSPI_1PAD, 0x08, |
| kFLEXSPI_Command_READ_SDR, kFLEXSPI_1PAD, 0x04), |
| }, |
| |
| [READ_NORMAL_OUTPUT] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_READ, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_READ_SDR, kFLEXSPI_1PAD, 0x04, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| |
| [READ_STATUS] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, 0x81, |
| kFLEXSPI_Command_READ_SDR, kFLEXSPI_1PAD, 0x04), |
| }, |
| |
| [PAGE_PROGRAM_INPUT] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, SPI_NOR_CMD_PP, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_WRITE_SDR, kFLEXSPI_1PAD, 0x04, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| |
| [PAGE_PROGRAM_QUAD_INPUT] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, 0x32, |
| kFLEXSPI_Command_RADDR_SDR, kFLEXSPI_1PAD, 0x18), |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_WRITE_SDR, kFLEXSPI_4PAD, 0x04, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| |
| [ENTER_QPI] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_1PAD, 0x35, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| |
| [EXIT_QPI] = { |
| FLEXSPI_LUT_SEQ(kFLEXSPI_Command_SDR, kFLEXSPI_4PAD, 0xF5, |
| kFLEXSPI_Command_STOP, kFLEXSPI_1PAD, 0), |
| }, |
| }; |
| |
| static int flash_flexspi_nor_get_vendor_id(const struct device *dev, |
| uint8_t *vendor_id) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| uint32_t buffer = 0; |
| int ret; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = 0, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Read, |
| .SeqNumber = 1, |
| .seqIndex = READ_ID, |
| .data = &buffer, |
| .dataSize = 1, |
| }; |
| |
| LOG_DBG("Reading id"); |
| |
| ret = memc_flexspi_transfer(data->controller, &transfer); |
| *vendor_id = buffer; |
| |
| return ret; |
| } |
| |
| static int flash_flexspi_nor_read_status(const struct device *dev, |
| uint32_t *status) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = 0, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Read, |
| .SeqNumber = 1, |
| .seqIndex = READ_STATUS_REG, |
| .data = status, |
| .dataSize = 1, |
| }; |
| |
| LOG_DBG("Reading status register"); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_write_status(const struct device *dev, |
| uint32_t *status) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = 0, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Write, |
| .SeqNumber = 1, |
| .seqIndex = WRITE_STATUS_REG, |
| .data = status, |
| .dataSize = 1, |
| }; |
| |
| LOG_DBG("Writing status register"); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_write_enable(const struct device *dev) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = 0, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Command, |
| .SeqNumber = 1, |
| .seqIndex = WRITE_ENABLE, |
| .data = NULL, |
| .dataSize = 0, |
| }; |
| |
| LOG_DBG("Enabling write"); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_erase_sector(const struct device *dev, |
| off_t offset) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = offset, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Command, |
| .SeqNumber = 1, |
| .seqIndex = ERASE_SECTOR, |
| .data = NULL, |
| .dataSize = 0, |
| }; |
| |
| LOG_DBG("Erasing sector at 0x%08zx", (ssize_t) offset); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_erase_block(const struct device *dev, |
| off_t offset) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = offset, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Command, |
| .SeqNumber = 1, |
| .seqIndex = ERASE_BLOCK, |
| .data = NULL, |
| .dataSize = 0, |
| }; |
| |
| LOG_DBG("Erasing block at 0x%08zx", (ssize_t) offset); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_erase_chip(const struct device *dev) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = 0, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Command, |
| .SeqNumber = 1, |
| .seqIndex = ERASE_CHIP, |
| .data = NULL, |
| .dataSize = 0, |
| }; |
| |
| LOG_DBG("Erasing chip"); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_page_program(const struct device *dev, |
| off_t offset, const void *buffer, size_t len) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| flexspi_transfer_t transfer = { |
| .deviceAddress = offset, |
| .port = data->port, |
| .cmdType = kFLEXSPI_Write, |
| .SeqNumber = 1, |
| .seqIndex = PAGE_PROGRAM_QUAD_INPUT, |
| .data = (uint32_t *) buffer, |
| .dataSize = len, |
| }; |
| |
| LOG_DBG("Page programming %d bytes to 0x%08zx", len, (ssize_t) offset); |
| |
| return memc_flexspi_transfer(data->controller, &transfer); |
| } |
| |
| static int flash_flexspi_nor_wait_bus_busy(const struct device *dev) |
| { |
| uint32_t status = 0; |
| int ret; |
| |
| do { |
| ret = flash_flexspi_nor_read_status(dev, &status); |
| LOG_DBG("status: 0x%x", status); |
| if (ret) { |
| LOG_ERR("Could not read status"); |
| return ret; |
| } |
| } while (status & BIT(0)); |
| |
| return 0; |
| } |
| |
| static int flash_flexspi_nor_enable_quad_mode(const struct device *dev) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| uint32_t status = 0x40; |
| |
| flash_flexspi_nor_write_status(dev, &status); |
| flash_flexspi_nor_wait_bus_busy(dev); |
| memc_flexspi_reset(data->controller); |
| |
| return 0; |
| } |
| |
| static int flash_flexspi_nor_read(const struct device *dev, off_t offset, |
| void *buffer, size_t len) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| uint8_t *src = memc_flexspi_get_ahb_address(data->controller, |
| data->port, |
| offset); |
| |
| memcpy(buffer, src, len); |
| |
| return 0; |
| } |
| |
| static int flash_flexspi_nor_write(const struct device *dev, off_t offset, |
| const void *buffer, size_t len) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| size_t size = len; |
| uint8_t *src = (uint8_t *) buffer; |
| int i; |
| unsigned int key = 0; |
| |
| uint8_t *dst = memc_flexspi_get_ahb_address(data->controller, |
| data->port, |
| offset); |
| |
| if (memc_flexspi_is_running_xip(data->controller)) { |
| /* |
| * ==== ENTER CRITICAL SECTION ==== |
| * No flash access should be performed in critical section. All |
| * code and data accessed must reside in ram. |
| */ |
| key = irq_lock(); |
| } |
| |
| while (len) { |
| /* If the offset isn't a multiple of the NOR page size, we first need |
| * to write the remaining part that fits, otherwise the write could |
| * be wrapped around within the same page |
| */ |
| i = MIN(SPI_NOR_PAGE_SIZE - (offset % SPI_NOR_PAGE_SIZE), len); |
| #ifdef CONFIG_FLASH_MCUX_FLEXSPI_NOR_WRITE_BUFFER |
| memcpy(nor_write_buf, src, i); |
| #endif |
| flash_flexspi_nor_write_enable(dev); |
| #ifdef CONFIG_FLASH_MCUX_FLEXSPI_NOR_WRITE_BUFFER |
| flash_flexspi_nor_page_program(dev, offset, nor_write_buf, i); |
| #else |
| flash_flexspi_nor_page_program(dev, offset, src, i); |
| #endif |
| flash_flexspi_nor_wait_bus_busy(dev); |
| memc_flexspi_reset(data->controller); |
| src += i; |
| offset += i; |
| len -= i; |
| } |
| |
| if (memc_flexspi_is_running_xip(data->controller)) { |
| /* ==== EXIT CRITICAL SECTION ==== */ |
| irq_unlock(key); |
| } |
| |
| #ifdef CONFIG_HAS_MCUX_CACHE |
| DCACHE_InvalidateByRange((uint32_t) dst, size); |
| #endif |
| |
| return 0; |
| } |
| |
| static int flash_flexspi_nor_erase(const struct device *dev, off_t offset, |
| size_t size) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| const size_t num_sectors = size / SPI_NOR_SECTOR_SIZE; |
| const size_t num_blocks = size / SPI_NOR_BLOCK_SIZE; |
| |
| int i; |
| unsigned int key = 0; |
| |
| uint8_t *dst = memc_flexspi_get_ahb_address(data->controller, |
| data->port, |
| offset); |
| |
| if (offset % SPI_NOR_SECTOR_SIZE) { |
| LOG_ERR("Invalid offset"); |
| return -EINVAL; |
| } |
| |
| if (size % SPI_NOR_SECTOR_SIZE) { |
| LOG_ERR("Invalid size"); |
| return -EINVAL; |
| } |
| |
| if (memc_flexspi_is_running_xip(data->controller)) { |
| /* |
| * ==== ENTER CRITICAL SECTION ==== |
| * No flash access should be performed in critical section. All |
| * code and data accessed must reside in ram. |
| */ |
| key = irq_lock(); |
| } |
| |
| if ((offset == 0) && (size == data->config.flashSize * KB(1))) { |
| flash_flexspi_nor_write_enable(dev); |
| flash_flexspi_nor_erase_chip(dev); |
| flash_flexspi_nor_wait_bus_busy(dev); |
| memc_flexspi_reset(data->controller); |
| } else if ((0 == (offset % SPI_NOR_BLOCK_SIZE)) && (0 == (size % SPI_NOR_BLOCK_SIZE))) { |
| for (i = 0; i < num_blocks; i++) { |
| flash_flexspi_nor_write_enable(dev); |
| flash_flexspi_nor_erase_block(dev, offset); |
| flash_flexspi_nor_wait_bus_busy(dev); |
| memc_flexspi_reset(data->controller); |
| offset += SPI_NOR_BLOCK_SIZE; |
| } |
| } else { |
| for (i = 0; i < num_sectors; i++) { |
| flash_flexspi_nor_write_enable(dev); |
| flash_flexspi_nor_erase_sector(dev, offset); |
| flash_flexspi_nor_wait_bus_busy(dev); |
| memc_flexspi_reset(data->controller); |
| offset += SPI_NOR_SECTOR_SIZE; |
| } |
| } |
| |
| if (memc_flexspi_is_running_xip(data->controller)) { |
| /* ==== EXIT CRITICAL SECTION ==== */ |
| irq_unlock(key); |
| } |
| |
| #ifdef CONFIG_HAS_MCUX_CACHE |
| DCACHE_InvalidateByRange((uint32_t) dst, size); |
| #endif |
| |
| return 0; |
| } |
| |
| static const struct flash_parameters *flash_flexspi_nor_get_parameters( |
| const struct device *dev) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| return &data->flash_parameters; |
| } |
| |
| #if defined(CONFIG_FLASH_PAGE_LAYOUT) |
| static void flash_flexspi_nor_pages_layout(const struct device *dev, |
| const struct flash_pages_layout **layout, size_t *layout_size) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| |
| *layout = &data->layout; |
| *layout_size = 1; |
| } |
| #endif /* CONFIG_FLASH_PAGE_LAYOUT */ |
| |
| static int flash_flexspi_nor_init(const struct device *dev) |
| { |
| struct flash_flexspi_nor_data *data = dev->data; |
| uint8_t vendor_id; |
| uint32_t temp_lut[sizeof(flash_flexspi_nor_lut) / sizeof(uint32_t)]; |
| |
| if (!device_is_ready(data->controller)) { |
| LOG_ERR("Controller device is not ready"); |
| return -ENODEV; |
| } |
| |
| if (!memc_flexspi_is_running_xip(data->controller) && |
| memc_flexspi_set_device_config(data->controller, &data->config, |
| data->port)) { |
| LOG_ERR("Could not set device configuration"); |
| return -EINVAL; |
| } |
| |
| /* |
| * Using the LUT stored in the FlexSPI directly when updating |
| * the FlexSPI can result in an invalid LUT entry being stored, |
| * as the LUT itself describes how the FlexSPI should access the flash. |
| * To resolve this, copy the LUT to a array placed in RAM before |
| * updating the FlexSPI. |
| */ |
| memcpy(temp_lut, flash_flexspi_nor_lut, |
| sizeof(flash_flexspi_nor_lut)); |
| |
| if (memc_flexspi_update_lut(data->controller, 0, |
| (const uint32_t *) temp_lut, |
| sizeof(temp_lut) / sizeof(uint32_t))) { |
| LOG_ERR("Could not update lut"); |
| return -EINVAL; |
| } |
| |
| memc_flexspi_reset(data->controller); |
| |
| if (flash_flexspi_nor_get_vendor_id(dev, &vendor_id)) { |
| LOG_ERR("Could not read vendor id"); |
| return -EIO; |
| } |
| LOG_DBG("Vendor id: 0x%0x", vendor_id); |
| |
| if (flash_flexspi_nor_enable_quad_mode(dev)) { |
| LOG_ERR("Could not enable quad mode"); |
| return -EIO; |
| } |
| |
| return 0; |
| } |
| |
| static const struct flash_driver_api flash_flexspi_nor_api = { |
| .erase = flash_flexspi_nor_erase, |
| .write = flash_flexspi_nor_write, |
| .read = flash_flexspi_nor_read, |
| .get_parameters = flash_flexspi_nor_get_parameters, |
| #if defined(CONFIG_FLASH_PAGE_LAYOUT) |
| .page_layout = flash_flexspi_nor_pages_layout, |
| #endif |
| }; |
| |
| #define CONCAT3(x, y, z) x ## y ## z |
| |
| #define CS_INTERVAL_UNIT(unit) \ |
| CONCAT3(kFLEXSPI_CsIntervalUnit, unit, SckCycle) |
| |
| #define AHB_WRITE_WAIT_UNIT(unit) \ |
| CONCAT3(kFLEXSPI_AhbWriteWaitUnit, unit, AhbCycle) |
| |
| #define FLASH_FLEXSPI_DEVICE_CONFIG(n) \ |
| { \ |
| .flexspiRootClk = MHZ(120), \ |
| .flashSize = DT_INST_PROP(n, size) / 8 / KB(1), \ |
| .CSIntervalUnit = \ |
| CS_INTERVAL_UNIT( \ |
| DT_INST_PROP(n, cs_interval_unit)), \ |
| .CSInterval = DT_INST_PROP(n, cs_interval), \ |
| .CSHoldTime = DT_INST_PROP(n, cs_hold_time), \ |
| .CSSetupTime = DT_INST_PROP(n, cs_setup_time), \ |
| .dataValidTime = DT_INST_PROP(n, data_valid_time), \ |
| .columnspace = DT_INST_PROP(n, column_space), \ |
| .enableWordAddress = DT_INST_PROP(n, word_addressable), \ |
| .AWRSeqIndex = 0, \ |
| .AWRSeqNumber = 0, \ |
| .ARDSeqIndex = READ_FAST_QUAD_OUTPUT, \ |
| .ARDSeqNumber = 1, \ |
| .AHBWriteWaitUnit = \ |
| AHB_WRITE_WAIT_UNIT( \ |
| DT_INST_PROP(n, ahb_write_wait_unit)), \ |
| .AHBWriteWaitInterval = \ |
| DT_INST_PROP(n, ahb_write_wait_interval), \ |
| } \ |
| |
| #define FLASH_FLEXSPI_NOR(n) \ |
| static struct flash_flexspi_nor_data \ |
| flash_flexspi_nor_data_##n = { \ |
| .controller = DEVICE_DT_GET(DT_INST_BUS(n)), \ |
| .config = FLASH_FLEXSPI_DEVICE_CONFIG(n), \ |
| .port = DT_INST_REG_ADDR(n), \ |
| .layout = { \ |
| .pages_count = DT_INST_PROP(n, size) / 8 \ |
| / SPI_NOR_SECTOR_SIZE, \ |
| .pages_size = SPI_NOR_SECTOR_SIZE, \ |
| }, \ |
| .flash_parameters = { \ |
| .write_block_size = NOR_WRITE_SIZE, \ |
| .erase_value = NOR_ERASE_VALUE, \ |
| }, \ |
| }; \ |
| \ |
| DEVICE_DT_INST_DEFINE(n, \ |
| flash_flexspi_nor_init, \ |
| NULL, \ |
| &flash_flexspi_nor_data_##n, \ |
| NULL, \ |
| POST_KERNEL, \ |
| CONFIG_FLASH_INIT_PRIORITY, \ |
| &flash_flexspi_nor_api); |
| |
| DT_INST_FOREACH_STATUS_OKAY(FLASH_FLEXSPI_NOR) |