blob: ca0f6e6ef2ec5a35f00fd86b77bca8c6634decf7 [file] [log] [blame] [edit]
/*
* Copyright (c) 2019, Henrik Brix Andersen <henrik@brixandersen.dk>
*
* Based on the i2c_mcux_lpi2c.c driver, which is:
* Copyright (c) 2016 Freescale Semiconductor, Inc.
* Copyright (c) 2019, NXP
*
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT openisa_rv32m1_lpi2c
#include <zephyr/drivers/i2c.h>
#include <zephyr/drivers/clock_control.h>
#include <zephyr/irq.h>
#include <fsl_lpi2c.h>
#include <zephyr/logging/log.h>
#include <zephyr/drivers/pinctrl.h>
LOG_MODULE_REGISTER(rv32m1_lpi2c);
#include "i2c-priv.h"
struct rv32m1_lpi2c_config {
LPI2C_Type *base;
const struct device *clock_dev;
clock_control_subsys_t clock_subsys;
clock_ip_name_t clock_ip_name;
uint32_t clock_ip_src;
uint32_t bitrate;
void (*irq_config_func)(const struct device *dev);
const struct pinctrl_dev_config *pincfg;
};
struct rv32m1_lpi2c_data {
lpi2c_master_handle_t handle;
struct k_sem transfer_sync;
struct k_sem completion_sync;
status_t completion_status;
};
static int rv32m1_lpi2c_configure(const struct device *dev,
uint32_t dev_config)
{
const struct rv32m1_lpi2c_config *config = dev->config;
uint32_t baudrate;
uint32_t clk_freq;
int err;
if (!(I2C_MODE_CONTROLLER & dev_config)) {
/* Slave mode not supported - yet */
LOG_ERR("Slave mode not supported");
return -ENOTSUP;
}
if (I2C_ADDR_10_BITS & dev_config) {
/* FSL LPI2C driver only supports 7-bit addressing */
LOG_ERR("10 bit addressing not supported");
return -ENOTSUP;
}
switch (I2C_SPEED_GET(dev_config)) {
case I2C_SPEED_STANDARD:
baudrate = KHZ(100);
break;
case I2C_SPEED_FAST:
baudrate = KHZ(400);
break;
case I2C_SPEED_FAST_PLUS:
baudrate = MHZ(1);
break;
/* TODO: only if SCL pin implements current source pull-up */
/* case I2C_SPEED_HIGH: */
/* baudrate = KHZ(3400); */
/* break; */
/* TODO: ultra-fast requires pin_config setting */
/* case I2C_SPEED_ULTRA: */
/* baudrate = MHZ(5); */
/* break; */
default:
LOG_ERR("Unsupported speed");
return -ENOTSUP;
}
err = clock_control_get_rate(config->clock_dev, config->clock_subsys, &clk_freq);
if (err) {
LOG_ERR("Could not get clock frequency (err %d)", err);
return -EINVAL;
}
LPI2C_MasterSetBaudRate(config->base, clk_freq, baudrate);
return 0;
}
static void rv32m1_lpi2c_master_transfer_callback(LPI2C_Type *base,
lpi2c_master_handle_t *handle,
status_t completionStatus,
void *userData)
{
struct rv32m1_lpi2c_data *data = userData;
ARG_UNUSED(base);
ARG_UNUSED(handle);
data->completion_status = completionStatus;
k_sem_give(&data->completion_sync);
}
static uint32_t rv32m1_lpi2c_convert_flags(int msg_flags)
{
uint32_t flags = 0U;
if (!(msg_flags & I2C_MSG_STOP)) {
flags |= kLPI2C_TransferNoStopFlag;
}
if (msg_flags & I2C_MSG_RESTART) {
flags |= kLPI2C_TransferRepeatedStartFlag;
}
return flags;
}
static int rv32m1_lpi2c_transfer(const struct device *dev,
struct i2c_msg *msgs,
uint8_t num_msgs, uint16_t addr)
{
const struct rv32m1_lpi2c_config *config = dev->config;
struct rv32m1_lpi2c_data *data = dev->data;
lpi2c_master_transfer_t transfer;
status_t status;
int ret = 0;
k_sem_take(&data->transfer_sync, K_FOREVER);
/* Iterate over all the messages */
for (int i = 0; i < num_msgs; i++) {
if (I2C_MSG_ADDR_10_BITS & msgs->flags) {
ret = -ENOTSUP;
goto out;
}
/* Initialize the transfer descriptor */
transfer.flags = rv32m1_lpi2c_convert_flags(msgs->flags);
/* Prevent the controller to send a start condition between
* messages, except if explicitly requested.
*/
if (i != 0 && !(msgs->flags & I2C_MSG_RESTART)) {
transfer.flags |= kLPI2C_TransferNoStartFlag;
}
transfer.slaveAddress = addr;
transfer.direction = (msgs->flags & I2C_MSG_READ)
? kLPI2C_Read : kLPI2C_Write;
transfer.subaddress = 0;
transfer.subaddressSize = 0;
transfer.data = msgs->buf;
transfer.dataSize = msgs->len;
/* Start the transfer */
status = LPI2C_MasterTransferNonBlocking(config->base,
&data->handle,
&transfer);
/* Return an error if the transfer didn't start successfully
* e.g., if the bus was busy
*/
if (status != kStatus_Success) {
LOG_DBG("Could not start transfer (status %d)", status);
ret = -EIO;
goto out;
}
/* Wait for the transfer to complete */
k_sem_take(&data->completion_sync, K_FOREVER);
/* Return an error if the transfer didn't complete
* successfully. e.g., nak, timeout, lost arbitration
*/
if (data->completion_status != kStatus_Success) {
LOG_DBG("Transfer failed (status %d)",
data->completion_status);
LPI2C_MasterTransferAbort(config->base, &data->handle);
ret = -EIO;
goto out;
}
/* Move to the next message */
msgs++;
}
out:
k_sem_give(&data->transfer_sync);
return ret;
}
static void rv32m1_lpi2c_isr(const struct device *dev)
{
const struct rv32m1_lpi2c_config *config = dev->config;
struct rv32m1_lpi2c_data *data = dev->data;
LPI2C_MasterTransferHandleIRQ(config->base, &data->handle);
}
static int rv32m1_lpi2c_init(const struct device *dev)
{
const struct rv32m1_lpi2c_config *config = dev->config;
struct rv32m1_lpi2c_data *data = dev->data;
lpi2c_master_config_t master_config;
uint32_t clk_freq, dev_cfg;
int err;
CLOCK_SetIpSrc(config->clock_ip_name, config->clock_ip_src);
if (!device_is_ready(config->clock_dev)) {
LOG_ERR("clock control device not ready");
return -ENODEV;
}
err = clock_control_on(config->clock_dev, config->clock_subsys);
if (err) {
LOG_ERR("Could not turn on clock (err %d)", err);
return -EINVAL;
}
err = clock_control_get_rate(config->clock_dev, config->clock_subsys, &clk_freq);
if (err) {
LOG_ERR("Could not get clock frequency (err %d)", err);
return -EINVAL;
}
LPI2C_MasterGetDefaultConfig(&master_config);
LPI2C_MasterInit(config->base, &master_config, clk_freq);
LPI2C_MasterTransferCreateHandle(config->base, &data->handle,
rv32m1_lpi2c_master_transfer_callback,
data);
dev_cfg = i2c_map_dt_bitrate(config->bitrate);
err = rv32m1_lpi2c_configure(dev, dev_cfg | I2C_MODE_CONTROLLER);
if (err) {
LOG_ERR("Could not configure controller (err %d)", err);
return err;
}
err = pinctrl_apply_state(config->pincfg, PINCTRL_STATE_DEFAULT);
if (err != 0) {
return err;
}
config->irq_config_func(dev);
return 0;
}
static const struct i2c_driver_api rv32m1_lpi2c_driver_api = {
.configure = rv32m1_lpi2c_configure,
.transfer = rv32m1_lpi2c_transfer,
};
#define RV32M1_LPI2C_DEVICE(id) \
PINCTRL_DT_INST_DEFINE(id); \
static void rv32m1_lpi2c_irq_config_func_##id(const struct device *dev); \
static const struct rv32m1_lpi2c_config rv32m1_lpi2c_##id##_config = { \
.base = \
(LPI2C_Type *)DT_INST_REG_ADDR(id), \
.clock_dev = DEVICE_DT_GET(DT_INST_CLOCKS_CTLR(id)), \
.clock_subsys = \
(clock_control_subsys_t) DT_INST_CLOCKS_CELL(id, name),\
.clock_ip_name = INST_DT_CLOCK_IP_NAME(id), \
.clock_ip_src = kCLOCK_IpSrcFircAsync, \
.bitrate = DT_INST_PROP(id, clock_frequency), \
.irq_config_func = rv32m1_lpi2c_irq_config_func_##id, \
.pincfg = PINCTRL_DT_INST_DEV_CONFIG_GET(id), \
}; \
static struct rv32m1_lpi2c_data rv32m1_lpi2c_##id##_data = { \
.transfer_sync = Z_SEM_INITIALIZER( \
rv32m1_lpi2c_##id##_data.transfer_sync, 1, 1), \
.completion_sync = Z_SEM_INITIALIZER( \
rv32m1_lpi2c_##id##_data.completion_sync, 0, 1), \
}; \
I2C_DEVICE_DT_INST_DEFINE(id, \
rv32m1_lpi2c_init, \
NULL, \
&rv32m1_lpi2c_##id##_data, \
&rv32m1_lpi2c_##id##_config, \
POST_KERNEL, CONFIG_I2C_INIT_PRIORITY, \
&rv32m1_lpi2c_driver_api); \
static void rv32m1_lpi2c_irq_config_func_##id(const struct device *dev) \
{ \
IRQ_CONNECT(DT_INST_IRQN(id), \
0, \
rv32m1_lpi2c_isr, DEVICE_DT_INST_GET(id), \
0); \
irq_enable(DT_INST_IRQN(id)); \
} \
DT_INST_FOREACH_STATUS_OKAY(RV32M1_LPI2C_DEVICE)