.. _rpi_pico:

Raspberry Pi Pico
#################

Overview
********

The Raspberry Pi Pico is a small, low-cost, versatile board from
Raspberry Pi. It is equipped with an RP2040 SoC, an on-board LED,
a USB connector, and an SWD interface. The USB bootloader allows it
to be flashed without any adapter, in a drag-and-drop manner.
It is also possible to flash and debug the Pico with its SWD interface,
using an external adapter.

Hardware
********
- Dual core Arm Cortex-M0+ processor running up to 133MHz
- 264KB on-chip SRAM
- 2MB on-board QSPI flash with XIP capabilities
- 26 GPIO pins
- 3 Analog inputs
- 2 UART peripherals
- 2 SPI controllers
- 2 I2C controllers
- 16 PWM channels
- USB 1.1 controller (host/device)
- 8 Programmable I/O (PIO) for custom peripherals
- On-board LED


.. figure:: img/rpi_pico.png
     :width: 150px
     :align: center
     :alt: Raspberry Pi Pico

     Raspberry Pi Pico (Image courtesy of Raspberry Pi)

Supported Features
==================

The rpi_pico board configuration supports the following
hardware features:

.. list-table::
   :header-rows: 1

   * - Peripheral
     - Kconfig option
     - Devicetree compatible
   * - NVIC
     - N/A
     - :dtcompatible:`arm,v6m-nvic`
   * - UART
     - :kconfig:`CONFIG_SERIAL`
     - :dtcompatible:`rpi,pico-uart`
   * - GPIO
     - :kconfig:`CONFIG_GPIO`
     - :dtcompatible:`rpi,pico-gpio`

Programming and Debugging
*************************

Flashing
========

Using an SWD adapter
--------------------

The Raspberry Pi Pico has an SWD interface that can be used to program
and debug the on board RP2040. This interface can be utilized by openocd.
However, to use it with the RP2040, a custom fork of openocd is needed.
This fork can be found here: https://github.com/raspberrypi/openocd

Depending on the interface used (such as JLink), you might need to
checkout to a branch that supports this interface, before proceeding.
Build and install openocd as described in the README.

When openocd is installed, you can flash the board with the following
command (assuming JLink is used):

.. code-block:: console

   $ openocd -f interface/jlink.cfg -c 'transport select swd' -f target/rp2040.cfg -c "adapter speed 2000" -c 'targets rp2040.core0' -c 'program path/to/zephyr.elf verify reset exit'

Using UF2
---------

If you don't have an SWD adapter, you can flash the Raspberry Pi Pico with
a UF2 file. By default, building an app for this board will generate a
`build/zephyr/zephyr.uf2` file. If the Pico is powered on with the `BOOTSEL`
button pressed, it will appear on the host as a mass storage device. The
UF2 file should be drag-and-dropped to the device, which will flash the Pico.

Debugging
=========

The SWD interface can also be used to debug the board. To achieve this,
install openocd as described for flashing the board. Also, install gdb-multiarch.
Then run the following command:

.. code-block:: console

   $ openocd -f interface/jlink.cfg -c 'transport select swd' -f target/rp2040.cfg -c "adapter speed 2000" -c 'targets rp2040.core0'

On another terminal, run:

.. code-block:: console

   $ gdb-multiarch

Inside gdb, run:

.. code-block:: console

   (gdb) tar ext :3333
   (gdb) file path/to/zephyr.elf

You can then start debugging the board.