/* ENC28J60 Stand-alone Ethernet Controller with SPI
 *
 * Copyright (c) 2016 Intel Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#include <net/ip/net_driver_ethernet.h>
#include <zephyr.h>
#include <string.h>
#include <errno.h>
#include <gpio.h>
#include <spi.h>
#include <eth.h>

#include "eth_enc28j60_priv.h"

#define D10D24S 11
#define MAX_BUFFER_LENGTH 100

static int eth_net_tx(struct net_buf *buf);
static void enc28j60_fiber_main(int arg1, int unused);

static int eth_enc28j60_soft_reset(struct device *dev)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_buf[2] = {ENC28J60_SPI_SC, 0xFF};

	return spi_write(context->spi, tx_buf, 2);
}

static void eth_enc28j60_set_bank(struct device *dev, uint16_t reg_addr)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_buf[2];

	tx_buf[0] = ENC28J60_SPI_RCR | ENC28J60_REG_ECON1;
	tx_buf[1] = 0x0;

	spi_transceive(context->spi, tx_buf, 2, tx_buf, 2);

	tx_buf[0] = ENC28J60_SPI_WCR | ENC28J60_REG_ECON1;
	tx_buf[1] = (tx_buf[1] & 0xFC) | ((reg_addr >> 8) & 0x0F);

	spi_write(context->spi, tx_buf, 2);
}

static void eth_enc28j60_write_reg(struct device *dev, uint16_t reg_addr,
				   uint8_t value)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_buf[2];

	tx_buf[0] = ENC28J60_SPI_WCR | (reg_addr & 0xFF);
	tx_buf[1] = value;

	spi_write(context->spi, tx_buf, 2);
}

static void eth_enc28j60_read_reg(struct device *dev, uint16_t reg_addr,
				  uint8_t *value)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_size = 2;
	uint8_t tx_buf[3];

	if (reg_addr & 0xF000) {
		tx_size = 3;
	}

	tx_buf[0] = ENC28J60_SPI_RCR | (reg_addr & 0xFF);
	tx_buf[1] = 0x0;

	spi_transceive(context->spi, tx_buf, tx_size, tx_buf, tx_size);

	*value = tx_buf[tx_size - 1];
}

static void eth_enc28j60_set_eth_reg(struct device *dev, uint16_t reg_addr,
				     uint8_t value)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_buf[2];

	tx_buf[0] = ENC28J60_SPI_BFS | (reg_addr & 0xFF);
	tx_buf[1] = value;

	spi_write(context->spi, tx_buf, 2);
}


static void eth_enc28j60_clear_eth_reg(struct device *dev, uint16_t reg_addr,
				       uint8_t value)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_buf[2];

	tx_buf[0] = ENC28J60_SPI_BFC | (reg_addr & 0xFF);
	tx_buf[1] = value;

	spi_write(context->spi, tx_buf, 2);
}

static void eth_enc28j60_write_mem(struct device *dev, uint8_t *data_buffer,
				   uint8_t buf_len)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t tx_buf[MAX_BUFFER_LENGTH + 1];
	uint8_t *index_buf;
	uint16_t num_segments;
	uint16_t num_remanents;

	index_buf = data_buffer;
	num_segments = buf_len / MAX_BUFFER_LENGTH;
	num_remanents = buf_len - MAX_BUFFER_LENGTH * num_segments;

	tx_buf[0] = ENC28J60_SPI_WBM;

	for (int i = 0; i < num_segments;
	     ++i, index_buf += i * MAX_BUFFER_LENGTH) {

		memcpy(tx_buf + 1, index_buf, MAX_BUFFER_LENGTH);

		spi_write(context->spi, tx_buf, MAX_BUFFER_LENGTH + 1);

	}
	memcpy(tx_buf + 1, index_buf, num_remanents);

	spi_write(context->spi, tx_buf, num_remanents + 1);
}

static void eth_enc28j60_read_mem(struct device *dev, uint8_t *data_buffer,
				  uint8_t buf_len)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t *index_buf;
	uint8_t tx_buf[MAX_BUFFER_LENGTH + 1];
	uint16_t num_segments;
	uint16_t num_remanents;

	index_buf = data_buffer;
	num_segments = buf_len / MAX_BUFFER_LENGTH;
	num_remanents = buf_len - MAX_BUFFER_LENGTH * num_segments;

	tx_buf[0] = ENC28J60_SPI_RBM;

	for (int i = 0; i < num_segments;
	     ++i, index_buf += i * MAX_BUFFER_LENGTH) {

		spi_transceive(context->spi, tx_buf, MAX_BUFFER_LENGTH + 1,
			       tx_buf, MAX_BUFFER_LENGTH + 1);

		memcpy(index_buf, tx_buf + 1, MAX_BUFFER_LENGTH);
	}

	spi_transceive(context->spi, tx_buf, num_remanents + 1,
		       tx_buf, num_remanents + 1);

	memcpy(index_buf, tx_buf + 1, num_remanents);
}

static void eth_enc28j60_read_phy(struct device *dev, uint16_t reg_addr,
				  int16_t *data)
{
	uint8_t rl, rh;
	uint8_t data_mistat;

	eth_enc28j60_set_bank(dev, ENC28J60_REG_MIREGADR);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MIREGADR, reg_addr);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MICMD,
			       ENC28J60_BIT_MICMD_MIIRD);
	eth_enc28j60_set_bank(dev, ENC28J60_REG_MISTAT);

	do {
		/* wait 10.24 useconds */
		sys_thread_busy_wait(D10D24S);
		eth_enc28j60_read_reg(dev, ENC28J60_REG_MISTAT,
				      &data_mistat);
	} while ((data_mistat & ENC28J60_BIT_MISTAT_BUSY));

	eth_enc28j60_set_bank(dev, ENC28J60_REG_MIREGADR);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MICMD, 0x00);
	eth_enc28j60_read_reg(dev, ENC28J60_REG_MIRDL, &rl);
	eth_enc28j60_read_reg(dev, ENC28J60_REG_MIRDH, &rh);
	*data = rl | ((uint16_t)rh << 8);
}

static void eth_enc28j60_write_phy(struct device *dev, uint16_t reg_addr,
				   int16_t data)
{
	uint8_t data_mistat;

	eth_enc28j60_set_bank(dev, ENC28J60_REG_MIREGADR);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MIREGADR, reg_addr);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MIWRL, data & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MIWRH, data >> 8);
	eth_enc28j60_set_bank(dev, ENC28J60_REG_MISTAT);

	do {
		/* wait 10.24 useconds */
		sys_thread_busy_wait(D10D24S);
		eth_enc28j60_read_reg(dev, ENC28J60_REG_MISTAT,
				      &data_mistat);
	} while ((data_mistat & ENC28J60_BIT_MISTAT_BUSY));
}

static void eth_enc28j60_gpio_callback(struct device *dev,
				       struct gpio_callback *cb,
				       uint32_t pins)
{
	struct eth_enc28j60_runtime *context =
		CONTAINER_OF(cb, struct eth_enc28j60_runtime, gpio_cb);

	nano_fiber_sem_give(&context->int_sem);
}

static void eth_enc28j60_init_buffers(struct device *dev)
{
	uint8_t data_estat;

	/* Reception buffers initialization */
	eth_enc28j60_set_bank(dev, ENC28J60_REG_ERXSTL);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXSTL,
			       ENC28J60_RXSTART & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXSTH,
			       ENC28J60_RXSTART >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXRDPTL,
			       ENC28J60_RXSTART & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXRDPTH,
			       ENC28J60_RXSTART >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXNDL,
			       ENC28J60_RXEND & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXNDH,
			       ENC28J60_RXEND >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXSTL,
			       ENC28J60_TXSTART & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXSTH,
			       ENC28J60_TXSTART >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXNDL,
			       ENC28J60_TXEND & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXNDH,
			       ENC28J60_TXEND >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERDPTL,
			       ENC28J60_RXSTART & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERDPTH,
			       ENC28J60_RXSTART >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_EWRPTL,
			       ENC28J60_TXSTART & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_EWRPTH,
			       ENC28J60_TXSTART >> 8);

	eth_enc28j60_set_bank(dev, ENC28J60_REG_ERXFCON);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXFCON,
			       ENC28J60_RECEIVE_FILTERS);

	/* Waiting for OST */
	do {
		/* wait 10.24 useconds */
		sys_thread_busy_wait(D10D24S);
		eth_enc28j60_read_reg(dev, ENC28J60_REG_ESTAT, &data_estat);
	} while (!(data_estat & ENC28J60_BIT_ESTAT_CLKRDY));
}

static void eth_enc28j60_init_mac(struct device *dev)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t data_macon;
	uint8_t mac_address[6];

	eth_enc28j60_set_bank(dev, ENC28J60_REG_MACON1);

	/* Set MARXEN to enable MAC to receive frames */
	eth_enc28j60_read_reg(dev, ENC28J60_REG_MACON1, &data_macon);
	data_macon |= ENC28J60_BIT_MACON1_MARXEN | ENC28J60_BIT_MACON1_RXPAUS
		      | ENC28J60_BIT_MACON1_TXPAUS;
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MACON1, data_macon);

	data_macon = ENC28J60_MAC_CONFIG;

	if (context->full_duplex) {
		data_macon |= ENC28J60_BIT_MACON3_FULDPX;
	}

	eth_enc28j60_write_reg(dev, ENC28J60_REG_MACON3, data_macon);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAIPGL, ENC28J60_MAC_NBBIPGL);

	if (context->full_duplex) {
		eth_enc28j60_write_reg(dev, ENC28J60_REG_MAIPGH,
				       ENC28J60_MAC_NBBIPGH);
		eth_enc28j60_write_reg(dev, ENC28J60_REG_MABBIPG,
				       ENC28J60_MAC_BBIPG_FD);
	} else {
		eth_enc28j60_write_reg(dev, ENC28J60_REG_MABBIPG,
				       ENC28J60_MAC_BBIPG_HD);
		eth_enc28j60_write_reg(dev, ENC28J60_REG_MACON4, 1 << 6);
	}

	/* Configure MAC address */
	mac_address[0] = MICROCHIP_OUI_B0;
	mac_address[1] = MICROCHIP_OUI_B1;
	mac_address[2] = MICROCHIP_OUI_B2;
	mac_address[3] = CONFIG_ETH_ENC28J60_0_MAC3;
	mac_address[4] = CONFIG_ETH_ENC28J60_0_MAC4;
	mac_address[5] = CONFIG_ETH_ENC28J60_0_MAC5;
	net_set_mac(mac_address, sizeof(mac_address));

	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAADR0,
			       CONFIG_ETH_ENC28J60_0_MAC5);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAADR1,
			       CONFIG_ETH_ENC28J60_0_MAC4);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAADR2,
			       CONFIG_ETH_ENC28J60_0_MAC3);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAADR3, MICROCHIP_OUI_B2);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAADR4, MICROCHIP_OUI_B1);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_MAADR5, MICROCHIP_OUI_B0);
}

static void eth_enc28j60_init_phy(struct device *dev)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;

	if (context->full_duplex) {
		eth_enc28j60_write_phy(dev, ENC28J60_PHY_PHCON1,
				       ENC28J60_BIT_PHCON1_PDPXMD);
		eth_enc28j60_write_phy(dev, ENC28J60_PHY_PHCON2, 0x0);
	} else {
		eth_enc28j60_write_phy(dev, ENC28J60_PHY_PHCON1, 0x0);
		eth_enc28j60_write_phy(dev, ENC28J60_PHY_PHCON2,
				       ENC28J60_BIT_PHCON2_HDLDIS);
	}
}

static int eth_enc28j60_init(struct device *dev)
{
	struct eth_enc28j60_config *config = dev->config->config_info;
	struct eth_enc28j60_runtime *context = dev->driver_data;
	struct spi_config spi_cfg;
	uint16_t data_phy;

	context->gpio = device_get_binding((char *)config->gpio_port);
	if (!context->gpio) {
		return -EINVAL;
	}

	context->spi = device_get_binding((char *)config->spi_port);
	if (!context->spi) {
		return -EINVAL;
	}

	/* Initialize GPIO */
	if (gpio_pin_configure(context->gpio, config->gpio_pin,
			       (GPIO_DIR_IN | GPIO_INT | GPIO_INT_EDGE
			       | GPIO_INT_ACTIVE_LOW | GPIO_INT_DEBOUNCE))) {
		return -EINVAL;
	}

	gpio_init_callback(&(context->gpio_cb), eth_enc28j60_gpio_callback,
			   BIT(config->gpio_pin));

	if (gpio_add_callback(context->gpio, &(context->gpio_cb))) {
		return -EINVAL;
	}

	if (gpio_pin_enable_callback(context->gpio, config->gpio_pin)) {
		return -EINVAL;
	}

	/* Initialize SPI:
	 * Mode: 0/0; Size: 8 bits; MSB
	 */
	spi_cfg.config = 8 << 4;
	spi_cfg.max_sys_freq = config->spi_freq;

	if (spi_configure(context->spi, &spi_cfg) < 0) {
		return -EIO;
	}

	if (spi_slave_select(context->spi, config->spi_slave) < 0) {
		return -EIO;
	}

	if (eth_enc28j60_soft_reset(dev)) {
		return -EIO;
	}

	/* Errata B7/2 */
	sys_thread_busy_wait(D10D24S);

	/* Select half-duplex/full-duplex from LED configuration */
	eth_enc28j60_read_phy(dev, ENC28J60_PHY_PHCON1, &data_phy);
	data_phy &= ENC28J60_BIT_PHCON1_PDPXMD;
	context->full_duplex = !!(data_phy);

	eth_enc28j60_init_buffers(dev);
	eth_enc28j60_init_mac(dev);
	eth_enc28j60_init_phy(dev);

	/* Enable interruptions */
	eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_EIE, ENC28J60_BIT_EIE_INTIE);
	eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_EIE, ENC28J60_BIT_EIE_TXIE);
	eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_EIE, ENC28J60_BIT_EIE_PKTIE);

	/* Enable Reception */
	eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_ECON1,
				 ENC28J60_BIT_ECON1_RXEN);

	/* Register tx callback into IP stack */
	net_driver_ethernet_register_tx(eth_net_tx);

	/* Initialize semaphores */
	nano_sem_init(&context->tx_sem);
	nano_sem_init(&context->int_sem);

	/* Start interruption-poll fiber */
	fiber_start(context->fiber_stack, ENC28J60_FIBER_STACK_SIZE,
		    enc28j60_fiber_main, (int)dev, 0,
		    ENC28J60_FIBER_PRIORITY, 0);

	return 0;
}

static int eth_enc28j60_tx(struct device *dev, uint8_t *buf, uint16_t len)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint16_t tx_bufaddr = ENC28J60_TXSTART;
	uint8_t per_packet_control;
	uint16_t tx_bufaddr_end;
	uint8_t tx_end;

	nano_fiber_sem_take(&context->tx_sem, TICKS_UNLIMITED);

	/* Latest errata sheet: DS80349C
	* always reset transmit logic (Errata Issue 12)
	* the Microchip TCP/IP stack implementation used to first check
	* whether TXERIF is set and only then reset the transmit logic
	* but this has been changed in later versions; possibly they
	* have a reason for this; they don't mention this in the errata
	* sheet
	*/
	eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_ECON1,
				 ENC28J60_BIT_ECON1_TXRST);
	eth_enc28j60_clear_eth_reg(dev, ENC28J60_REG_ECON1,
				   ENC28J60_BIT_ECON1_TXRST);

	/* Write the buffer content into the transmission buffer */
	eth_enc28j60_set_bank(dev, ENC28J60_REG_ETXSTL);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_EWRPTL, tx_bufaddr & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_EWRPTH, tx_bufaddr >> 8);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXSTL, tx_bufaddr & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXSTH, tx_bufaddr >> 8);

	/* Write the data into the buffer */
	per_packet_control = ENC28J60_PPCTL_BYTE;
	eth_enc28j60_write_mem(dev, &per_packet_control, 1);
	eth_enc28j60_write_mem(dev, buf, len);

	tx_bufaddr_end = tx_bufaddr + len;
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXNDL,
			       tx_bufaddr_end & 0xFF);
	eth_enc28j60_write_reg(dev, ENC28J60_REG_ETXNDH, tx_bufaddr_end >> 8);

	/* Clear transmit interruption flag */
	eth_enc28j60_clear_eth_reg(dev, ENC28J60_REG_EIR,
				   ENC28J60_BIT_EIR_TXIF
				   | ENC28J60_BIT_EIR_TXERIF);
	/* Signal ENC28J60 to send the buffer */
	eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_ECON1,
				 ENC28J60_BIT_ECON1_TXRTS);

	do {
		/* wait 10.24 useconds */
		sys_thread_busy_wait(D10D24S);
		eth_enc28j60_read_reg(dev, ENC28J60_REG_EIR, &tx_end);
		tx_end &= ENC28J60_BIT_EIR_TXIF;
	} while (!tx_end);

	eth_enc28j60_read_reg(dev, ENC28J60_REG_EIR, &tx_end);

	nano_sem_give(&context->tx_sem);

	if (tx_end & ENC28J60_BIT_ESTAT_TXABRT)	{
		return -1;
	}

	return 0;
}

static int eth_enc28j60_rx(struct device *dev)
{
	struct eth_enc28j60_runtime *context = dev->driver_data;
	uint8_t rx_flag;

	/* Check if there are received frames in buffer */
	eth_enc28j60_read_reg(dev, ENC28J60_REG_EIR, &rx_flag);

	rx_flag &= ENC28J60_BIT_EIR_PKTIF;
	while (rx_flag) {
		struct net_buf *buf;
		uint8_t np[2];
		uint8_t *reception_buf;
		uint16_t frm_len = 0;
		uint16_t next_packet;

		/* Read address for next packet */
		eth_enc28j60_read_mem(dev, np, 2);
		next_packet = np[0] | (uint16_t)np[1] << 8;

		/* Read reception status vector */
		eth_enc28j60_read_mem(dev, context->rx_rsv, 4);

		/* Get the frame length from the rx status vector */
		frm_len = (context->rx_rsv[1] << 8) | context->rx_rsv[0];

		if (frm_len > UIP_BUFSIZE) {
			return -EIO;
		}
		/* Get the frame from the buffer */
		buf = ip_buf_get_reserve_rx(0);
		reception_buf = net_buf_add(buf, frm_len);

		eth_enc28j60_read_mem(dev, reception_buf, frm_len);
		uip_len(buf) = frm_len;

		/* Register the buffer frame with the IP stack */
		net_driver_ethernet_recv(buf);

		/* Free buffer memory and decrement rx counter */
		eth_enc28j60_set_bank(dev, ENC28J60_REG_ERXRDPTL);
		eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXRDPTL,
				       next_packet & 0xFF);
		eth_enc28j60_write_reg(dev, ENC28J60_REG_ERXRDPTH,
				       next_packet >> 8);
		eth_enc28j60_set_eth_reg(dev, ENC28J60_REG_ECON2,
					 ENC28J60_BIT_ECON2_PKTDEC);

		/* Call receive callback */
		if (context->receive_callback) {
			context->receive_callback(reception_buf, frm_len);
		}

		/* Check if there are frames to clean from the buffer */
		eth_enc28j60_read_reg(dev, ENC28J60_REG_EIR, &rx_flag);
		rx_flag &= ENC28J60_BIT_EIR_PKTIF;
	}
	return 0;
}

void eth_enc28j60_reg_cb(struct device *dev,
			 void (*cb)(uint8_t *buffer, uint16_t len))
{
	struct eth_enc28j60_runtime *context = dev->driver_data;

	context->receive_callback = cb;
}

static void enc28j60_fiber_main(int arg1, int unused)
{
	struct device *dev = (struct device *)arg1;
	struct eth_enc28j60_runtime *context;
	uint8_t int_stat;

	ARG_UNUSED(unused);

	context = dev->driver_data;

	while (1) {
		nano_fiber_sem_take(&context->int_sem, TICKS_UNLIMITED);
		eth_enc28j60_read_reg(dev, ENC28J60_REG_EIR, &int_stat);

		if (int_stat & ENC28J60_BIT_EIR_PKTIF) {
			eth_enc28j60_rx(dev);
			/* Clear rx interruption flag */
			eth_enc28j60_clear_eth_reg(dev, ENC28J60_REG_EIR,
						   ENC28J60_BIT_EIR_PKTIF
						   | ENC28J60_BIT_EIR_RXERIF);
		}
	}
}

static struct eth_driver_api api_funcs = {
	.send = eth_enc28j60_tx,
	.register_callback = eth_enc28j60_reg_cb,
};

#ifdef CONFIG_ETH_ENC28J60_0
static struct eth_enc28j60_runtime eth_enc28j60_0_runtime = {
	.receive_callback = NULL,
};

static struct eth_enc28j60_config eth_enc28j60_0_config = {
	.gpio_port = CONFIG_ETH_ENC28J60_0_GPIO_PORT_NAME,
	.gpio_pin = CONFIG_ETH_ENC28J60_0_GPIO_PIN,
	.spi_port = CONFIG_ETH_ENC28J60_0_SPI_PORT_NAME,
	.spi_freq  = CONFIG_ETH_ENC28J60_0_SPI_BUS_FREQ,
	.spi_slave = CONFIG_ETH_ENC28J60_0_SLAVE,
};

DEVICE_AND_API_INIT(eth_enc28j60_0, CONFIG_ETH_ENC28J60_0_NAME,
		    &eth_enc28j60_init, &eth_enc28j60_0_runtime,
		    &eth_enc28j60_0_config, SECONDARY,
		    CONFIG_ETH_ENC28J60_0_INIT_PRIORITY, &api_funcs);

static int eth_net_tx(struct net_buf *buf)
{
	return eth_enc28j60_tx(DEVICE_GET(eth_enc28j60_0),
			       uip_buf(buf), uip_len(buf));
}

#endif /* CONFIG_ETH_ENC28J60_0 */