/* ns16550.c - NS16550D serial driver */

#define DT_DRV_COMPAT ns16550

/*
 * Copyright (c) 2010, 2012-2015 Wind River Systems, Inc.
 * Copyright (c) 2020 Intel Corp.
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/**
 * @brief NS16550 Serial Driver
 *
 * This is the driver for the Intel NS16550 UART Chip used on the PC 386.
 * It uses the SCCs in asynchronous mode only.
 *
 * Before individual UART port can be used, uart_ns16550_port_init() has to be
 * called to setup the port.
 *
 * - the following macro for the number of bytes between register addresses:
 *
 *  UART_REG_ADDR_INTERVAL
 */

#include <errno.h>
#include <kernel.h>
#include <arch/cpu.h>
#include <zephyr/types.h>
#include <soc.h>

#include <init.h>
#include <toolchain.h>
#include <linker/sections.h>
#include <drivers/uart.h>
#include <sys/sys_io.h>
#include <spinlock.h>

#include "uart_ns16550.h"

#define INST_HAS_PCP_HELPER(inst) DT_INST_NODE_HAS_PROP(inst, pcp) ||
#define INST_HAS_DLF_HELPER(inst) DT_INST_NODE_HAS_PROP(inst, dlf) ||
#define INST_HAS_REG_SHIFT_HELPER(inst) \
	DT_INST_NODE_HAS_PROP(inst, reg_shift) ||

#define UART_NS16550_PCP_ENABLED \
	(DT_INST_FOREACH_STATUS_OKAY(INST_HAS_PCP_HELPER) 0)
#define UART_NS16550_DLF_ENABLED \
	(DT_INST_FOREACH_STATUS_OKAY(INST_HAS_DLF_HELPER) 0)
#define UART_NS16550_REG_INTERVAL_ENABLED \
	(DT_INST_FOREACH_STATUS_OKAY(INST_HAS_REG_SHIFT_HELPER) 0)

#if DT_ANY_INST_ON_BUS_STATUS_OKAY(pcie)
BUILD_ASSERT(IS_ENABLED(CONFIG_PCIE), "NS16550(s) in DT need CONFIG_PCIE");
#include <drivers/pcie/pcie.h>
#endif

/* register definitions */

#define REG_THR 0x00  /* Transmitter holding reg.       */
#define REG_RDR 0x00  /* Receiver data reg.             */
#define REG_BRDL 0x00 /* Baud rate divisor (LSB)        */
#define REG_BRDH 0x01 /* Baud rate divisor (MSB)        */
#define REG_IER 0x01  /* Interrupt enable reg.          */
#define REG_IIR 0x02  /* Interrupt ID reg.              */
#define REG_FCR 0x02  /* FIFO control reg.              */
#define REG_LCR 0x03  /* Line control reg.              */
#define REG_MDC 0x04  /* Modem control reg.             */
#define REG_LSR 0x05  /* Line status reg.               */
#define REG_MSR 0x06  /* Modem status reg.              */
#define REG_DLF 0xC0  /* Divisor Latch Fraction         */
#define REG_PCP 0x200 /* PRV_CLOCK_PARAMS (Apollo Lake) */

/* equates for interrupt enable register */

#define IER_RXRDY 0x01 /* receiver data ready */
#define IER_TBE 0x02   /* transmit bit enable */
#define IER_LSR 0x04   /* line status interrupts */
#define IER_MSI 0x08   /* modem status interrupts */

/* equates for interrupt identification register */

#define IIR_MSTAT 0x00 /* modem status interrupt  */
#define IIR_NIP   0x01 /* no interrupt pending    */
#define IIR_THRE  0x02 /* transmit holding register empty interrupt */
#define IIR_RBRF  0x04 /* receiver buffer register full interrupt */
#define IIR_LS    0x06 /* receiver line status interrupt */
#define IIR_MASK  0x07 /* interrupt id bits mask  */
#define IIR_ID    0x06 /* interrupt ID mask without NIP */

/* equates for FIFO control register */

#define FCR_FIFO 0x01    /* enable XMIT and RCVR FIFO */
#define FCR_RCVRCLR 0x02 /* clear RCVR FIFO */
#define FCR_XMITCLR 0x04 /* clear XMIT FIFO */

/* equates for Apollo Lake clock control register (PRV_CLOCK_PARAMS) */

#define PCP_UPDATE 0x80000000 /* update clock */
#define PCP_EN 0x00000001     /* enable clock output */

/*
 * Per PC16550D (Literature Number: SNLS378B):
 *
 * RXRDY, Mode 0: When in the 16450 Mode (FCR0 = 0) or in
 * the FIFO Mode (FCR0 = 1, FCR3 = 0) and there is at least 1
 * character in the RCVR FIFO or RCVR holding register, the
 * RXRDY pin (29) will be low active. Once it is activated the
 * RXRDY pin will go inactive when there are no more charac-
 * ters in the FIFO or holding register.
 *
 * RXRDY, Mode 1: In the FIFO Mode (FCR0 = 1) when the
 * FCR3 = 1 and the trigger level or the timeout has been
 * reached, the RXRDY pin will go low active. Once it is acti-
 * vated it will go inactive when there are no more characters
 * in the FIFO or holding register.
 *
 * TXRDY, Mode 0: In the 16450 Mode (FCR0 = 0) or in the
 * FIFO Mode (FCR0 = 1, FCR3 = 0) and there are no charac-
 * ters in the XMIT FIFO or XMIT holding register, the TXRDY
 * pin (24) will be low active. Once it is activated the TXRDY
 * pin will go inactive after the first character is loaded into the
 * XMIT FIFO or holding register.
 *
 * TXRDY, Mode 1: In the FIFO Mode (FCR0 = 1) when
 * FCR3 = 1 and there are no characters in the XMIT FIFO, the
 * TXRDY pin will go low active. This pin will become inactive
 * when the XMIT FIFO is completely full.
 */
#define FCR_MODE0 0x00 /* set receiver in mode 0 */
#define FCR_MODE1 0x08 /* set receiver in mode 1 */

/* RCVR FIFO interrupt levels: trigger interrupt with this bytes in FIFO */
#define FCR_FIFO_1 0x00  /* 1 byte in RCVR FIFO */
#define FCR_FIFO_4 0x40  /* 4 bytes in RCVR FIFO */
#define FCR_FIFO_8 0x80  /* 8 bytes in RCVR FIFO */
#define FCR_FIFO_14 0xC0 /* 14 bytes in RCVR FIFO */

/*
 * UART NS16750 supports 64 bytes FIFO, which can be enabled
 * via the FCR register
 */
#define FCR_FIFO_64 0x20 /* Enable 64 bytes FIFO */

/* constants for line control register */

#define LCR_CS5 0x00   /* 5 bits data size */
#define LCR_CS6 0x01   /* 6 bits data size */
#define LCR_CS7 0x02   /* 7 bits data size */
#define LCR_CS8 0x03   /* 8 bits data size */
#define LCR_2_STB 0x04 /* 2 stop bits */
#define LCR_1_STB 0x00 /* 1 stop bit */
#define LCR_PEN 0x08   /* parity enable */
#define LCR_PDIS 0x00  /* parity disable */
#define LCR_EPS 0x10   /* even parity select */
#define LCR_SP 0x20    /* stick parity select */
#define LCR_SBRK 0x40  /* break control bit */
#define LCR_DLAB 0x80  /* divisor latch access enable */

/* constants for the modem control register */

#define MCR_DTR 0x01  /* dtr output */
#define MCR_RTS 0x02  /* rts output */
#define MCR_OUT1 0x04 /* output #1 */
#define MCR_OUT2 0x08 /* output #2 */
#define MCR_LOOP 0x10 /* loop back */
#define MCR_AFCE 0x20 /* auto flow control enable */

/* constants for line status register */

#define LSR_RXRDY 0x01 /* receiver data available */
#define LSR_OE 0x02    /* overrun error */
#define LSR_PE 0x04    /* parity error */
#define LSR_FE 0x08    /* framing error */
#define LSR_BI 0x10    /* break interrupt */
#define LSR_EOB_MASK 0x1E /* Error or Break mask */
#define LSR_THRE 0x20  /* transmit holding register empty */
#define LSR_TEMT 0x40  /* transmitter empty */

/* constants for modem status register */

#define MSR_DCTS 0x01 /* cts change */
#define MSR_DDSR 0x02 /* dsr change */
#define MSR_DRI 0x04  /* ring change */
#define MSR_DDCD 0x08 /* data carrier change */
#define MSR_CTS 0x10  /* complement of cts */
#define MSR_DSR 0x20  /* complement of dsr */
#define MSR_RI 0x40   /* complement of ring signal */
#define MSR_DCD 0x80  /* complement of dcd */

/* convenience defines */

#define DEV_CFG(dev) \
	((const struct uart_ns16550_device_config * const) \
	 (dev)->config)
#define DEV_DATA(dev) \
	((struct uart_ns16550_dev_data *)(dev)->data)

#define THR(dev) (get_port(dev) + REG_THR * reg_interval(dev))
#define RDR(dev) (get_port(dev) + REG_RDR * reg_interval(dev))
#define BRDL(dev) (get_port(dev) + REG_BRDL * reg_interval(dev))
#define BRDH(dev) (get_port(dev) + REG_BRDH * reg_interval(dev))
#define IER(dev) (get_port(dev) + REG_IER * reg_interval(dev))
#define IIR(dev) (get_port(dev) + REG_IIR * reg_interval(dev))
#define FCR(dev) (get_port(dev) + REG_FCR * reg_interval(dev))
#define LCR(dev) (get_port(dev) + REG_LCR * reg_interval(dev))
#define MDC(dev) (get_port(dev) + REG_MDC * reg_interval(dev))
#define LSR(dev) (get_port(dev) + REG_LSR * reg_interval(dev))
#define MSR(dev) (get_port(dev) + REG_MSR * reg_interval(dev))
#define DLF(dev) (get_port(dev) + REG_DLF)
#define PCP(dev) (get_port(dev) + REG_PCP)

#define IIRC(dev) (DEV_DATA(dev)->iir_cache)

#ifdef UART_NS16550_ACCESS_IOPORT
#define INBYTE(x) sys_in8(x)
#define INWORD(x) sys_in32(x)
#define OUTBYTE(x, d) sys_out8(d, x)
#define OUTWORD(x, d) sys_out32(d, x)
#else
#define INBYTE(x) sys_read8(x)
#define INWORD(x) sys_read32(x)
#define OUTBYTE(x, d) sys_write8(d, x)
#define OUTWORD(x, d) sys_write32(d, x)
#endif /* UART_NS16550_ACCESS_IOPORT */

#ifdef CONFIG_UART_NS16550_ACCESS_WORD_ONLY
#undef INBYTE
#define INBYTE(x) INWORD(x)
#undef OUTBYTE
#define OUTBYTE(x, d) OUTWORD(x, d)
#endif

/* device config */
struct uart_ns16550_device_config {
#ifndef UART_NS16550_ACCESS_IOPORT
	DEVICE_MMIO_ROM;
#else
	uint32_t port;
#endif
	uint32_t sys_clk_freq;
#if defined(CONFIG_UART_INTERRUPT_DRIVEN) || defined(CONFIG_UART_ASYNC_API)
	uart_irq_config_func_t	irq_config_func;
#endif
#if UART_NS16550_PCP_ENABLED
	uint32_t pcp;
#endif
#if UART_NS16550_REG_INTERVAL_ENABLED
	uint8_t reg_interval;
#endif
#if DT_ANY_INST_ON_BUS_STATUS_OKAY(pcie)
	bool pcie;
	pcie_bdf_t pcie_bdf;
	pcie_id_t pcie_id;
#endif
};

/** Device data structure */
struct uart_ns16550_dev_data {
#ifndef UART_NS16550_ACCESS_IOPORT
	DEVICE_MMIO_RAM;
#endif
	struct uart_config uart_config;
	struct k_spinlock lock;

#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	uint8_t iir_cache;	/**< cache of IIR since it clears when read */
	uart_irq_callback_user_data_t cb;  /**< Callback function pointer */
	void *cb_data;	/**< Callback function arg */
#endif

#if UART_NS16550_DLF_ENABLED
	uint8_t dlf;		/**< DLF value */
#endif
};

#if defined(UART_REG_ADDR_INTERVAL)
#define DEFAULT_REG_INTERVAL UART_REG_ADDR_INTERVAL
#elif defined(UART_NS16550_ACCESS_IOPORT)
#define DEFAULT_REG_INTERVAL 1
#else
#define DEFAULT_REG_INTERVAL 4
#endif

#if UART_NS16550_REG_INTERVAL_ENABLED
static inline uint8_t reg_interval(const struct device *dev)
{
	if (DEV_CFG(dev)->reg_interval) {
		return DEV_CFG(dev)->reg_interval;
	}

	return DEFAULT_REG_INTERVAL;
}
#else
#define reg_interval(dev) DEFAULT_REG_INTERVAL
#endif

static const struct uart_driver_api uart_ns16550_driver_api;

static inline uintptr_t get_port(const struct device *dev)
{
#ifndef UART_NS16550_ACCESS_IOPORT
	return DEVICE_MMIO_GET(dev);
#else
	return DEV_CFG(dev)->port;
#endif
}

static void set_baud_rate(const struct device *dev, uint32_t baud_rate)
{
	const struct uart_ns16550_device_config * const dev_cfg = DEV_CFG(dev);
	struct uart_ns16550_dev_data * const dev_data = DEV_DATA(dev);
	uint32_t divisor; /* baud rate divisor */
	uint8_t lcr_cache;

	if ((baud_rate != 0U) && (dev_cfg->sys_clk_freq != 0U)) {
		/*
		 * calculate baud rate divisor. a variant of
		 * (uint32_t)(dev_cfg->sys_clk_freq / (16.0 * baud_rate) + 0.5)
		 */
		divisor = ((dev_cfg->sys_clk_freq + (baud_rate << 3))
					/ baud_rate) >> 4;

		/* set the DLAB to access the baud rate divisor registers */
		lcr_cache = INBYTE(LCR(dev));
		OUTBYTE(LCR(dev), LCR_DLAB | lcr_cache);
		OUTBYTE(BRDL(dev), (unsigned char)(divisor & 0xff));
		OUTBYTE(BRDH(dev), (unsigned char)((divisor >> 8) & 0xff));

		/* restore the DLAB to access the baud rate divisor registers */
		OUTBYTE(LCR(dev), lcr_cache);

		dev_data->uart_config.baudrate = baud_rate;
	}
}

static int uart_ns16550_configure(const struct device *dev,
				  const struct uart_config *cfg)
{
	struct uart_ns16550_dev_data * const dev_data = DEV_DATA(dev);
	const struct uart_ns16550_device_config * const dev_cfg = DEV_CFG(dev);
	uint8_t lcr_cache;
	uint8_t mdc = 0U;

	/* temp for return value if error occurs in this locked region */
	int ret = 0;

	k_spinlock_key_t key = k_spin_lock(&dev_data->lock);

	ARG_UNUSED(dev_data);
	ARG_UNUSED(dev_cfg);

#ifndef UART_NS16550_ACCESS_IOPORT
#if DT_ANY_INST_ON_BUS_STATUS_OKAY(pcie)
	if (dev_cfg->pcie) {
		struct pcie_mbar mbar;

		if (!pcie_probe(dev_cfg->pcie_bdf, dev_cfg->pcie_id)) {
			ret = -EINVAL;
			goto out;
		}

		pcie_get_mbar(dev_cfg->pcie_bdf, 0, &mbar);
		pcie_set_cmd(dev_cfg->pcie_bdf, PCIE_CONF_CMDSTAT_MEM, true);

		device_map(DEVICE_MMIO_RAM_PTR(dev), mbar.phys_addr, mbar.size,
			   K_MEM_CACHE_NONE);
	} else
#endif /* DT_ANY_INST_ON_BUS_STATUS_OKAY(pcie) */
	{
		/* Map directly from DTS */
		DEVICE_MMIO_MAP(dev, K_MEM_CACHE_NONE);
	}
#endif /* UART_NS15660_ACCESS_IOPORT */

#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	dev_data->iir_cache = 0U;
#endif

#if UART_NS16550_DLF_ENABLED
	OUTBYTE(DLF(dev), dev_data->dlf);
#endif

#if UART_NS16550_PCP_ENABLED
	uint32_t pcp = dev_cfg->pcp;

	if (pcp) {
		pcp |= PCP_EN;
		OUTWORD(PCP(dev), pcp & ~PCP_UPDATE);
		OUTWORD(PCP(dev), pcp | PCP_UPDATE);
	}
#endif

	set_baud_rate(dev, cfg->baudrate);

	/* Local structure to hold temporary values to pass to OUTBYTE() */
	struct uart_config uart_cfg;

	switch (cfg->data_bits) {
	case UART_CFG_DATA_BITS_5:
		uart_cfg.data_bits = LCR_CS5;
		break;
	case UART_CFG_DATA_BITS_6:
		uart_cfg.data_bits = LCR_CS6;
		break;
	case UART_CFG_DATA_BITS_7:
		uart_cfg.data_bits = LCR_CS7;
		break;
	case UART_CFG_DATA_BITS_8:
		uart_cfg.data_bits = LCR_CS8;
		break;
	default:
		ret = -ENOTSUP;
		goto out;
	}

	switch (cfg->stop_bits) {
	case UART_CFG_STOP_BITS_1:
		uart_cfg.stop_bits = LCR_1_STB;
		break;
	case UART_CFG_STOP_BITS_2:
		uart_cfg.stop_bits = LCR_2_STB;
		break;
	default:
		ret = -ENOTSUP;
		goto out;
	}

	switch (cfg->parity) {
	case UART_CFG_PARITY_NONE:
		uart_cfg.parity = LCR_PDIS;
		break;
	case UART_CFG_PARITY_EVEN:
		uart_cfg.parity = LCR_EPS;
		break;
	default:
		ret = -ENOTSUP;
		goto out;
	}

	dev_data->uart_config = *cfg;

	/* data bits, stop bits, parity, clear DLAB */
	OUTBYTE(LCR(dev),
		uart_cfg.data_bits | uart_cfg.stop_bits | uart_cfg.parity);

	mdc = MCR_OUT2 | MCR_RTS | MCR_DTR;
#ifdef CONFIG_UART_NS16750
	if (cfg->flow_ctrl == UART_CFG_FLOW_CTRL_RTS_CTS) {
		mdc |= MCR_AFCE;
	}
#endif

	OUTBYTE(MDC(dev), mdc);

	/*
	 * Program FIFO: enabled, mode 0 (set for compatibility with quark),
	 * generate the interrupt at 8th byte
	 * Clear TX and RX FIFO
	 */
	OUTBYTE(FCR(dev),
		FCR_FIFO | FCR_MODE0 | FCR_FIFO_8 | FCR_RCVRCLR | FCR_XMITCLR
#ifdef CONFIG_UART_NS16750
		| FCR_FIFO_64
#endif
		);

	/* clear the port */
	lcr_cache = INBYTE(LCR(dev));
	OUTBYTE(LCR(dev), LCR_DLAB | lcr_cache);
	INBYTE(RDR(dev));
	OUTBYTE(LCR(dev), lcr_cache);

	/* disable interrupts  */
	OUTBYTE(IER(dev), 0x00);

out:
	k_spin_unlock(&dev_data->lock, key);
	return ret;
};

static int uart_ns16550_config_get(const struct device *dev,
				   struct uart_config *cfg)
{
	struct uart_ns16550_dev_data *data = DEV_DATA(dev);

	cfg->baudrate = data->uart_config.baudrate;
	cfg->parity = data->uart_config.parity;
	cfg->stop_bits = data->uart_config.stop_bits;
	cfg->data_bits = data->uart_config.data_bits;
	cfg->flow_ctrl = data->uart_config.flow_ctrl;

	return 0;
}

/**
 * @brief Initialize individual UART port
 *
 * This routine is called to reset the chip in a quiescent state.
 *
 * @param dev UART device struct
 *
 * @return 0 if successful, failed otherwise
 */
static int uart_ns16550_init(const struct device *dev)
{
	int ret;

	ret = uart_ns16550_configure(dev, &DEV_DATA(dev)->uart_config);
	if (ret != 0) {
		return ret;
	}

#ifdef CONFIG_UART_INTERRUPT_DRIVEN
	DEV_CFG(dev)->irq_config_func(dev);
#endif

	return 0;
}

/**
 * @brief Poll the device for input.
 *
 * @param dev UART device struct
 * @param c Pointer to character
 *
 * @return 0 if a character arrived, -1 if the input buffer if empty.
 */
static int uart_ns16550_poll_in(const struct device *dev, unsigned char *c)
{
	int ret = -1;
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	if ((INBYTE(LSR(dev)) & LSR_RXRDY) != 0) {
		/* got a character */
		*c = INBYTE(RDR(dev));
		ret = 0;
	}

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return ret;
}

/**
 * @brief Output a character in polled mode.
 *
 * Checks if the transmitter is empty. If empty, a character is written to
 * the data register.
 *
 * If the hardware flow control is enabled then the handshake signal CTS has to
 * be asserted in order to send a character.
 *
 * @param dev UART device struct
 * @param c Character to send
 */
static void uart_ns16550_poll_out(const struct device *dev,
					   unsigned char c)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	while ((INBYTE(LSR(dev)) & LSR_THRE) == 0) {
	}

	OUTBYTE(THR(dev), c);

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Check if an error was received
 *
 * @param dev UART device struct
 *
 * @return one of UART_ERROR_OVERRUN, UART_ERROR_PARITY, UART_ERROR_FRAMING,
 * UART_BREAK if an error was detected, 0 otherwise.
 */
static int uart_ns16550_err_check(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);
	int check = (INBYTE(LSR(dev)) & LSR_EOB_MASK);

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return check >> 1;
}

#if CONFIG_UART_INTERRUPT_DRIVEN

/**
 * @brief Fill FIFO with data
 *
 * @param dev UART device struct
 * @param tx_data Data to transmit
 * @param size Number of bytes to send
 *
 * @return Number of bytes sent
 */
static int uart_ns16550_fifo_fill(const struct device *dev,
				  const uint8_t *tx_data,
				  int size)
{
	int i;
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	for (i = 0; (i < size) && (INBYTE(LSR(dev)) & LSR_THRE) != 0; i++) {
		OUTBYTE(THR(dev), tx_data[i]);
	}

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return i;
}

/**
 * @brief Read data from FIFO
 *
 * @param dev UART device struct
 * @param rxData Data container
 * @param size Container size
 *
 * @return Number of bytes read
 */
static int uart_ns16550_fifo_read(const struct device *dev, uint8_t *rx_data,
				  const int size)
{
	int i;
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	for (i = 0; (i < size) && (INBYTE(LSR(dev)) & LSR_RXRDY) != 0; i++) {
		rx_data[i] = INBYTE(RDR(dev));
	}

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return i;
}

/**
 * @brief Enable TX interrupt in IER
 *
 * @param dev UART device struct
 *
 * @return N/A
 */
static void uart_ns16550_irq_tx_enable(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	OUTBYTE(IER(dev), INBYTE(IER(dev)) | IER_TBE);

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Disable TX interrupt in IER
 *
 * @param dev UART device struct
 *
 * @return N/A
 */
static void uart_ns16550_irq_tx_disable(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	OUTBYTE(IER(dev), INBYTE(IER(dev)) & (~IER_TBE));

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Check if Tx IRQ has been raised
 *
 * @param dev UART device struct
 *
 * @return 1 if an IRQ is ready, 0 otherwise
 */
static int uart_ns16550_irq_tx_ready(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	int ret = ((IIRC(dev) & IIR_ID) == IIR_THRE) ? 1 : 0;

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return ret;
}

/**
 * @brief Check if nothing remains to be transmitted
 *
 * @param dev UART device struct
 *
 * @return 1 if nothing remains to be transmitted, 0 otherwise
 */
static int uart_ns16550_irq_tx_complete(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	int ret = ((INBYTE(LSR(dev)) & (LSR_TEMT | LSR_THRE))
				== (LSR_TEMT | LSR_THRE)) ? 1 : 0;

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return ret;
}

/**
 * @brief Enable RX interrupt in IER
 *
 * @param dev UART device struct
 *
 * @return N/A
 */
static void uart_ns16550_irq_rx_enable(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	OUTBYTE(IER(dev), INBYTE(IER(dev)) | IER_RXRDY);

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Disable RX interrupt in IER
 *
 * @param dev UART device struct
 *
 * @return N/A
 */
static void uart_ns16550_irq_rx_disable(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	OUTBYTE(IER(dev), INBYTE(IER(dev)) & (~IER_RXRDY));

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Check if Rx IRQ has been raised
 *
 * @param dev UART device struct
 *
 * @return 1 if an IRQ is ready, 0 otherwise
 */
static int uart_ns16550_irq_rx_ready(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	int ret = ((IIRC(dev) & IIR_ID) == IIR_RBRF) ? 1 : 0;

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return ret;
}

/**
 * @brief Enable error interrupt in IER
 *
 * @param dev UART device struct
 *
 * @return N/A
 */
static void uart_ns16550_irq_err_enable(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	OUTBYTE(IER(dev), INBYTE(IER(dev)) | IER_LSR);

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Disable error interrupt in IER
 *
 * @param dev UART device struct
 *
 * @return 1 if an IRQ is ready, 0 otherwise
 */
static void uart_ns16550_irq_err_disable(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	OUTBYTE(IER(dev), INBYTE(IER(dev)) & (~IER_LSR));

	k_spin_unlock(&DEV_DATA(dev)->lock, key);
}

/**
 * @brief Check if any IRQ is pending
 *
 * @param dev UART device struct
 *
 * @return 1 if an IRQ is pending, 0 otherwise
 */
static int uart_ns16550_irq_is_pending(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	int ret = (!(IIRC(dev) & IIR_NIP)) ? 1 : 0;

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return ret;
}

/**
 * @brief Update cached contents of IIR
 *
 * @param dev UART device struct
 *
 * @return Always 1
 */
static int uart_ns16550_irq_update(const struct device *dev)
{
	k_spinlock_key_t key = k_spin_lock(&DEV_DATA(dev)->lock);

	IIRC(dev) = INBYTE(IIR(dev));

	k_spin_unlock(&DEV_DATA(dev)->lock, key);

	return 1;
}

/**
 * @brief Set the callback function pointer for IRQ.
 *
 * @param dev UART device struct
 * @param cb Callback function pointer.
 *
 * @return N/A
 */
static void uart_ns16550_irq_callback_set(const struct device *dev,
					  uart_irq_callback_user_data_t cb,
					  void *cb_data)
{
	struct uart_ns16550_dev_data * const dev_data = DEV_DATA(dev);
	k_spinlock_key_t key = k_spin_lock(&dev_data->lock);

	dev_data->cb = cb;
	dev_data->cb_data = cb_data;

	k_spin_unlock(&dev_data->lock, key);
}

/**
 * @brief Interrupt service routine.
 *
 * This simply calls the callback function, if one exists.
 *
 * @param arg Argument to ISR.
 *
 * @return N/A
 */
static void uart_ns16550_isr(const struct device *dev)
{
	struct uart_ns16550_dev_data * const dev_data = DEV_DATA(dev);

	if (dev_data->cb) {
		dev_data->cb(dev, dev_data->cb_data);
	}

}

#endif /* CONFIG_UART_INTERRUPT_DRIVEN */

#ifdef CONFIG_UART_NS16550_LINE_CTRL

/**
 * @brief Manipulate line control for UART.
 *
 * @param dev UART device struct
 * @param ctrl The line control to be manipulated
 * @param val Value to set the line control
 *
 * @return 0 if successful, failed otherwise
 */
static int uart_ns16550_line_ctrl_set(const struct device *dev,
				      uint32_t ctrl, uint32_t val)
{
	uint32_t mdc, chg;
	k_spinlock_key_t key;

	switch (ctrl) {
	case UART_LINE_CTRL_BAUD_RATE:
		set_baud_rate(dev, val);
		return 0;

	case UART_LINE_CTRL_RTS:
	case UART_LINE_CTRL_DTR:
		key = k_spin_lock(&DEV_DATA(dev)->lock);
		mdc = INBYTE(MDC(dev));

		if (ctrl == UART_LINE_CTRL_RTS) {
			chg = MCR_RTS;
		} else {
			chg = MCR_DTR;
		}

		if (val) {
			mdc |= chg;
		} else {
			mdc &= ~(chg);
		}
		OUTBYTE(MDC(dev), mdc);
		k_spin_unlock(&DEV_DATA(dev)->lock, key);
		return 0;
	}

	return -ENOTSUP;
}

#endif /* CONFIG_UART_NS16550_LINE_CTRL */

#ifdef CONFIG_UART_NS16550_DRV_CMD

/**
 * @brief Send extra command to driver
 *
 * @param dev UART device struct
 * @param cmd Command to driver
 * @param p Parameter to the command
 *
 * @return 0 if successful, failed otherwise
 */
static int uart_ns16550_drv_cmd(const struct device *dev, uint32_t cmd,
				uint32_t p)
{
#if UART_NS16550_DLF_ENABLED
	if (cmd == CMD_SET_DLF) {
		struct uart_ns16550_dev_data * const dev_data = DEV_DATA(dev);
		k_spinlock_key_t key = k_spin_lock(&dev_data->lock);

		dev_data->dlf = p;
		OUTBYTE(DLF(dev), dev_data->dlf);
		k_spin_unlock(&dev_data->lock, key);
		return 0;
	}
#endif

	return -ENOTSUP;
}

#endif /* CONFIG_UART_NS16550_DRV_CMD */


static const struct uart_driver_api uart_ns16550_driver_api = {
	.poll_in = uart_ns16550_poll_in,
	.poll_out = uart_ns16550_poll_out,
	.err_check = uart_ns16550_err_check,
	.configure = uart_ns16550_configure,
	.config_get = uart_ns16550_config_get,
#ifdef CONFIG_UART_INTERRUPT_DRIVEN

	.fifo_fill = uart_ns16550_fifo_fill,
	.fifo_read = uart_ns16550_fifo_read,
	.irq_tx_enable = uart_ns16550_irq_tx_enable,
	.irq_tx_disable = uart_ns16550_irq_tx_disable,
	.irq_tx_ready = uart_ns16550_irq_tx_ready,
	.irq_tx_complete = uart_ns16550_irq_tx_complete,
	.irq_rx_enable = uart_ns16550_irq_rx_enable,
	.irq_rx_disable = uart_ns16550_irq_rx_disable,
	.irq_rx_ready = uart_ns16550_irq_rx_ready,
	.irq_err_enable = uart_ns16550_irq_err_enable,
	.irq_err_disable = uart_ns16550_irq_err_disable,
	.irq_is_pending = uart_ns16550_irq_is_pending,
	.irq_update = uart_ns16550_irq_update,
	.irq_callback_set = uart_ns16550_irq_callback_set,

#endif

#ifdef CONFIG_UART_NS16550_LINE_CTRL
	.line_ctrl_set = uart_ns16550_line_ctrl_set,
#endif

#ifdef CONFIG_UART_NS16550_DRV_CMD
	.drv_cmd = uart_ns16550_drv_cmd,
#endif
};

#define UART_NS16550_IRQ_FLAGS_SENSE0(n) 0
#define UART_NS16550_IRQ_FLAGS_SENSE1(n) DT_INST_IRQ(n, sense)
#define UART_NS16550_IRQ_FLAGS(n) \
	_CONCAT(UART_NS16550_IRQ_FLAGS_SENSE, DT_INST_IRQ_HAS_CELL(n, sense))(n)

/* not PCI(e) */
#define UART_NS16550_IRQ_CONFIG_PCIE0(n)                                \
	static void irq_config_func##n(const struct device *dev)        \
	{                                                               \
		ARG_UNUSED(dev);                                        \
		IRQ_CONNECT(DT_INST_IRQN(n), DT_INST_IRQ(n, priority),  \
			    uart_ns16550_isr, DEVICE_DT_INST_GET(n),    \
			    UART_NS16550_IRQ_FLAGS(n));                 \
		irq_enable(DT_INST_IRQN(n));                            \
	}

/* PCI(e) with auto IRQ detection */
#define UART_NS16550_IRQ_CONFIG_PCIE1(n)                                      \
	static void irq_config_func##n(const struct device *dev)              \
	{                                                                     \
		ARG_UNUSED(dev);                                              \
		BUILD_ASSERT(DT_INST_IRQN(n) == PCIE_IRQ_DETECT,              \
			     "Only runtime IRQ configuration is supported");  \
		BUILD_ASSERT(IS_ENABLED(CONFIG_DYNAMIC_INTERRUPTS),           \
			     "NS16550 PCIe requires dynamic interrupts");     \
		unsigned int irq = pcie_alloc_irq(DT_INST_REG_ADDR(n));       \
		if (irq == PCIE_CONF_INTR_IRQ_NONE) {                         \
			return;                                               \
		}                                                             \
		irq_connect_dynamic(irq, DT_INST_IRQ(n, priority),            \
				    (void (*)(const void *))uart_ns16550_isr, \
				    DEVICE_DT_INST_GET(n),                    \
				    UART_NS16550_IRQ_FLAGS(n));               \
		pcie_irq_enable(DT_INST_REG_ADDR(n), irq);                    \
	}

#ifdef UART_NS16550_ACCESS_IOPORT
#define DEV_CONFIG_REG_INIT(n) \
	.port = DT_INST_REG_ADDR(n),
#else
#define DEV_CONFIG_REG_INIT_PCIE0(n) DEVICE_MMIO_ROM_INIT(DT_DRV_INST(n)),
#define DEV_CONFIG_REG_INIT_PCIE1(n)
#define DEV_CONFIG_REG_INIT(n) \
	_CONCAT(DEV_CONFIG_REG_INIT_PCIE, DT_INST_ON_BUS(n, pcie))(n)
#endif

#ifdef CONFIG_UART_INTERRUPT_DRIVEN
#define DEV_CONFIG_IRQ_FUNC_INIT(n) \
	.irq_config_func = irq_config_func##n,
#define UART_NS16550_IRQ_FUNC_DECLARE(n) \
	static void irq_config_func##n(const struct device *dev);
#define UART_NS16550_IRQ_FUNC_DEFINE(n) \
	_CONCAT(UART_NS16550_IRQ_CONFIG_PCIE, DT_INST_ON_BUS(n, pcie))(n)
#else
/* !CONFIG_UART_INTERRUPT_DRIVEN */
#define DEV_CONFIG_IRQ_FUNC_INIT(n)
#define UART_NS16550_IRQ_FUNC_DECLARE(n)
#define UART_NS16550_IRQ_FUNC_DEFINE(n)
#endif /* CONFIG_UART_INTERRUPT_DRIVEN */

#if UART_NS16550_PCP_ENABLED
#define DEV_CONFIG_PCP_INIT(n) .pcp = DT_INST_PROP_OR(n, pcp, 0),
#else
#define DEV_CONFIG_PCP_INIT(n)
#endif

#define DEV_CONFIG_REG_INT0(n)
#define DEV_CONFIG_REG_INT1(n) \
	.reg_interval = (1 << DT_INST_PROP(n, reg_shift)),
#define DEV_CONFIG_REG_INT_INIT(n) \
	_CONCAT(DEV_CONFIG_REG_INT, DT_INST_NODE_HAS_PROP(n, reg_shift))(n)

#define DEV_CONFIG_PCIE0(n)
#define DEV_CONFIG_PCIE1(n)              \
	.pcie = true,                    \
	.pcie_bdf = DT_INST_REG_ADDR(n), \
	.pcie_id = DT_INST_REG_SIZE(n),
#define DEV_CONFIG_PCIE_INIT(n) \
	_CONCAT(DEV_CONFIG_PCIE, DT_INST_ON_BUS(n, pcie))(n)

#define DEV_DATA_FLOW_CTRL0 UART_CFG_FLOW_CTRL_NONE
#define DEV_DATA_FLOW_CTRL1 UART_CFG_FLOW_CTRL_RTS_CTS
#define DEV_DATA_FLOW_CTRL(n) \
	_CONCAT(DEV_DATA_FLOW_CTRL, DT_INST_NODE_HAS_PROP(n, hw_flow_control))

#define DEV_DATA_DLF0(n)
#define DEV_DATA_DLF1(n) \
	.dlf = DT_INST_PROP(n, dlf),
#define DEV_DATA_DLF_INIT(n) \
	_CONCAT(DEV_DATA_DLF, DT_INST_NODE_HAS_PROP(n, dlf))(n)

#define UART_NS16550_DEVICE_INIT(n)                                                  \
	UART_NS16550_IRQ_FUNC_DECLARE(n);                                            \
	static const struct uart_ns16550_device_config uart_ns16550_dev_cfg_##n = {  \
		DEV_CONFIG_REG_INIT(n)                                               \
		.sys_clk_freq = DT_INST_PROP(n, clock_frequency),                    \
		DEV_CONFIG_IRQ_FUNC_INIT(n)                                          \
		DEV_CONFIG_PCP_INIT(n)                                               \
		DEV_CONFIG_REG_INT_INIT(n)                                           \
		DEV_CONFIG_PCIE_INIT(n)                                              \
	};                                                                           \
	static struct uart_ns16550_dev_data uart_ns16550_dev_data_##n = {            \
		.uart_config.baudrate = DT_INST_PROP_OR(n, current_speed, 0),        \
		.uart_config.parity = UART_CFG_PARITY_NONE,                          \
		.uart_config.stop_bits = UART_CFG_STOP_BITS_1,                       \
		.uart_config.data_bits = UART_CFG_DATA_BITS_8,                       \
		.uart_config.flow_ctrl = DEV_DATA_FLOW_CTRL(n),                      \
		DEV_DATA_DLF_INIT(n)                                                 \
	};                                                                           \
	DEVICE_DT_INST_DEFINE(n, &uart_ns16550_init, NULL,                           \
			      &uart_ns16550_dev_data_##n, &uart_ns16550_dev_cfg_##n, \
			      PRE_KERNEL_1, CONFIG_KERNEL_INIT_PRIORITY_DEVICE,      \
			      &uart_ns16550_driver_api);                             \
	UART_NS16550_IRQ_FUNC_DEFINE(n)

DT_INST_FOREACH_STATUS_OKAY(UART_NS16550_DEVICE_INIT)