# Copyright (c) 2021 STMicroelectronics
# SPDX-License-Identifier: Apache-2.0

include: sensor-device.yaml

properties:
  irq-gpios:
    type: phandle-array
    description: |
      DRDY pin

      This pin defaults to active high when produced by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.

  int-pin:
    type: int
    default: 1
    enum:
      - 1 # drdy is generated from INT1
      - 2 # drdy is generated from INT2
    description: |
      Select DRDY pin number (1 or 2).

      This number represents which of the two interrupt pins
      (INT1 or INT2) the drdy line is attached to. This property is not
      mandatory and if not present it defaults to 1 which is the
      configuration at power-up.

  accel-pm:
    type: int
    default: 0
    description: |
      Specify the accelerometer power mode.
      Default is power-up configuration.
    enum:
      - 0 # High Performance mode (default)
      - 1 # Low/Normal Power mode
      - 2 # Ultra Low Power mode

  accel-range:
    type: int
    default: 0
    description: |
      Range in g. Default is power-up configuration.
    enum:
      - 0 # 2g  (0.061 mg/LSB) (LSM6DSO32 will be double these values)
      - 1 # 16g (0.488 mg/LSB)
      - 2 # 4g  (0.122 mg/LSB)
      - 3 # 8g  (0.244 mg/LSB)

  accel-odr:
    type: int
    default: 0
    description: |
      Specify the default accelerometer output data rate expressed in samples per second (Hz).
      Default is power-up configuration.
    enum:
      - 0  # Power-Down
      - 1  # 12.5Hz
      - 2  # 26Hz
      - 3  # 52Hz
      - 4  # 104Hz
      - 5  # 208Hz
      - 6  # 417Hz
      - 7  # 833Hz
      - 8  # 1667Hz
      - 9  # 3333Hz
      - 10 # 6667Hz

  gyro-pm:
    type: int
    default: 0
    description: |
      Specify the gyrometer power mode.
      Default is power-up configuration.
    enum:
      - 0 # High Performance mode (default)
      - 1 # Low/Normal Power mode

  gyro-range:
    type: int
    default: 0
    description: |
      Range in dps. Default is power-up configuration.
    enum:
      - 0 # 250 dps  (8.75 mdps/LSB)
      - 1 # 125 dps  (4.375 mdps/LSB)
      - 2 # 500 dps  (17.50 mdps/LSB)
      - 4 # 1000 dps (35 mdps/LSB)
      - 6 # 2000 dps (70 mdps/LSB)

  gyro-odr:
    type: int
    default: 0
    description: |
      Specify the default gyro output data rate expressed in samples per second (Hz).
      Default is power-up configuration.
    enum:
      - 0  # Power-Down
      - 1  # 12.5Hz
      - 2  # 26Hz
      - 3  # 52Hz
      - 4  # 104Hz
      - 5  # 208Hz
      - 6  # 417Hz
      - 7  # 833Hz
      - 8  # 1667Hz
      - 9  # 3333Hz
      - 10 # 6667Hz

  drdy-pulsed:
    type: boolean
    description: |
      Selects the pulsed mode for data-ready interrupt when enabled,
      and the latched mode when disabled.