# Copyright (c), 2021 NXP
# SPDX -License-Identifier: Apache-2.0

description: |
  NXP PCA9420 PMIC

  The PMIC has two buck converters and two LDOs. All need to be defined as
  children nodes, strictly following the BUCK1, BUCK2, LDO1 and LDO2 node names.
  For example:

  pmic@61 {
    reg = <0x61>;
    ...
    BUCK1 {
      /* all properties for BUCK1 */
    };
    BUCK2 {
      /* all properties for BUCK2 */
    };
    LDO1 {
      /* all properties for LDO1 */
    };
    LDO2 {
      /* all properties for LDO2 */
    };
  };


compatible: "nxp,pca9420"

include: base.yaml

properties:
  nxp,enable-modesel-pins:
    type: boolean
    description:
      When enabled, the PMIC will be configured to allow mode selection using
      the MODESEL0/1 inputs.

  nxp,vin-ilim-microamp:
    type: int
    default: 425000
    enum:
      - 85000
      - 255000
      - 425000
      - 595000
      - 765000
      - 935000
      - 1105000
    description: |
      VIN input current limit, in microamperes. Value reflects typical value,
      below you can find min/typical/max values:

      - 74 mA/85 mA/98 mA
      - 222 mA/255 mA/293 mA
      - 370 mA/425 mA/489 mA
      - 517 mA/595 mA/684 mA
      - 665 mA/765 mA/880 mA
      - 813 mA/935 mA/1075 mA
      - 961 mA/1105 mA/1271 mA

      To disable current limit, set property to zero. Defaults to 425mA, the IC
      default value.

  nxp,asys-uvlo-sel-millivolt:
    type: int
    default: 2700
    enum:
      - 2400
      - 2500
      - 2600
      - 2700
    description: |
      ASYS UVLO (under voltage lock out) threshold, in millivolts. Defaults to
      2700mV to match the IC default value.

child-binding:
  include:
    - name: regulator.yaml
      property-allowlist:
        - regulator-always-on
        - regulator-boot-on
        - regulator-min-microvolt
        - regulator-max-microvolt

  description: Voltage output of PMIC controller regulator
  properties:
    enable-inverted:
      type: boolean
      description: |
        If the enable bit should be zero to turn the regulator on, add this
        property.

    nxp,mode0-microvolt:
      type: int
      description: |
        The voltage level to be configured for mode 0, in microvolts. Setting
        this value to zero will disable the source in mode 0.

    nxp,mode1-microvolt:
      type: int
      description: |
        The voltage level to be configured for mode 1, in microvolts. Setting
        this value to zero will disable the source in mode 1.

    nxp,mode2-microvolt:
      type: int
      description: |
        The voltage level to be configured for mode 2, in microvolts. Setting
        this value to zero will disable the source in mode 2.

    nxp,mode3-microvolt:
      type: int
      description: |
        The voltage level to be configured for mode 3, in microvolts. Setting
        this value to zero will disable the source in mode 3.