| /** | |
| ****************************************************************************** | |
| * @file stm32l1xx_hal_pwr.h | |
| * @author MCD Application Team | |
| * @brief Header file of PWR HAL module. | |
| ****************************************************************************** | |
| * @attention | |
| * | |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. | |
| * All rights reserved.</center></h2> | |
| * | |
| * This software component is licensed by ST under BSD 3-Clause license, | |
| * the "License"; You may not use this file except in compliance with the | |
| * License. You may obtain a copy of the License at: | |
| * opensource.org/licenses/BSD-3-Clause | |
| * | |
| ****************************************************************************** | |
| */ | |
| /* Define to prevent recursive inclusion -------------------------------------*/ | |
| #ifndef __STM32L1xx_HAL_PWR_H | |
| #define __STM32L1xx_HAL_PWR_H | |
| #ifdef __cplusplus | |
| extern "C" { | |
| #endif | |
| /* Includes ------------------------------------------------------------------*/ | |
| #include "stm32l1xx_hal_def.h" | |
| /** @addtogroup STM32L1xx_HAL_Driver | |
| * @{ | |
| */ | |
| /** @addtogroup PWR | |
| * @{ | |
| */ | |
| /* Exported types ------------------------------------------------------------*/ | |
| /** @defgroup PWR_Exported_Types PWR Exported Types | |
| * @{ | |
| */ | |
| /** | |
| * @brief PWR PVD configuration structure definition | |
| */ | |
| typedef struct | |
| { | |
| uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level. | |
| This parameter can be a value of @ref PWR_PVD_detection_level */ | |
| uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins. | |
| This parameter can be a value of @ref PWR_PVD_Mode */ | |
| }PWR_PVDTypeDef; | |
| /** | |
| * @} | |
| */ | |
| /* Internal constants --------------------------------------------------------*/ | |
| /** @addtogroup PWR_Private_Constants | |
| * @{ | |
| */ | |
| #define PWR_EXTI_LINE_PVD (0x00010000U) /*!< External interrupt line 16 Connected to the PVD EXTI Line */ | |
| /** | |
| * @} | |
| */ | |
| /* Exported constants --------------------------------------------------------*/ | |
| /** @defgroup PWR_Exported_Constants PWR Exported Constants | |
| * @{ | |
| */ | |
| /** @defgroup PWR_register_alias_address PWR Register alias address | |
| * @{ | |
| */ | |
| /* ------------- PWR registers bit address in the alias region ---------------*/ | |
| #define PWR_OFFSET (PWR_BASE - PERIPH_BASE) | |
| #define PWR_CR_OFFSET 0x00 | |
| #define PWR_CSR_OFFSET 0x04 | |
| #define PWR_CR_OFFSET_BB (PWR_OFFSET + PWR_CR_OFFSET) | |
| #define PWR_CSR_OFFSET_BB (PWR_OFFSET + PWR_CSR_OFFSET) | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_CR_register_alias PWR CR Register alias address | |
| * @{ | |
| */ | |
| /* --- CR Register ---*/ | |
| /* Alias word address of LPSDSR bit */ | |
| #define LPSDSR_BIT_NUMBER POSITION_VAL(PWR_CR_LPSDSR) | |
| #define CR_LPSDSR_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (LPSDSR_BIT_NUMBER * 4))) | |
| /* Alias word address of DBP bit */ | |
| #define DBP_BIT_NUMBER POSITION_VAL(PWR_CR_DBP) | |
| #define CR_DBP_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (DBP_BIT_NUMBER * 4))) | |
| /* Alias word address of LPRUN bit */ | |
| #define LPRUN_BIT_NUMBER POSITION_VAL(PWR_CR_LPRUN) | |
| #define CR_LPRUN_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (LPRUN_BIT_NUMBER * 4))) | |
| /* Alias word address of PVDE bit */ | |
| #define PVDE_BIT_NUMBER POSITION_VAL(PWR_CR_PVDE) | |
| #define CR_PVDE_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (PVDE_BIT_NUMBER * 4))) | |
| /* Alias word address of FWU bit */ | |
| #define FWU_BIT_NUMBER POSITION_VAL(PWR_CR_FWU) | |
| #define CR_FWU_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (FWU_BIT_NUMBER * 4))) | |
| /* Alias word address of ULP bit */ | |
| #define ULP_BIT_NUMBER POSITION_VAL(PWR_CR_ULP) | |
| #define CR_ULP_BB ((uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32) + (ULP_BIT_NUMBER * 4))) | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_CSR_register_alias PWR CSR Register alias address | |
| * @{ | |
| */ | |
| /* --- CSR Register ---*/ | |
| /* Alias word address of EWUP1, EWUP2 and EWUP3 bits */ | |
| #define CSR_EWUP_BB(VAL) ((uint32_t)(PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32) + (POSITION_VAL(VAL) * 4))) | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_PVD_detection_level PWR PVD detection level | |
| * @{ | |
| */ | |
| #define PWR_PVDLEVEL_0 PWR_CR_PLS_LEV0 | |
| #define PWR_PVDLEVEL_1 PWR_CR_PLS_LEV1 | |
| #define PWR_PVDLEVEL_2 PWR_CR_PLS_LEV2 | |
| #define PWR_PVDLEVEL_3 PWR_CR_PLS_LEV3 | |
| #define PWR_PVDLEVEL_4 PWR_CR_PLS_LEV4 | |
| #define PWR_PVDLEVEL_5 PWR_CR_PLS_LEV5 | |
| #define PWR_PVDLEVEL_6 PWR_CR_PLS_LEV6 | |
| #define PWR_PVDLEVEL_7 PWR_CR_PLS_LEV7 /* External input analog voltage | |
| (Compare internally to VREFINT) */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_PVD_Mode PWR PVD Mode | |
| * @{ | |
| */ | |
| #define PWR_PVD_MODE_NORMAL (0x00000000U) /*!< basic mode is used */ | |
| #define PWR_PVD_MODE_IT_RISING (0x00010001U) /*!< External Interrupt Mode with Rising edge trigger detection */ | |
| #define PWR_PVD_MODE_IT_FALLING (0x00010002U) /*!< External Interrupt Mode with Falling edge trigger detection */ | |
| #define PWR_PVD_MODE_IT_RISING_FALLING (0x00010003U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ | |
| #define PWR_PVD_MODE_EVENT_RISING (0x00020001U) /*!< Event Mode with Rising edge trigger detection */ | |
| #define PWR_PVD_MODE_EVENT_FALLING (0x00020002U) /*!< Event Mode with Falling edge trigger detection */ | |
| #define PWR_PVD_MODE_EVENT_RISING_FALLING (0x00020003U) /*!< Event Mode with Rising/Falling edge trigger detection */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode | |
| * @{ | |
| */ | |
| #define PWR_MAINREGULATOR_ON (0x00000000U) | |
| #define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPSDSR | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry | |
| * @{ | |
| */ | |
| #define PWR_SLEEPENTRY_WFI ((uint8_t)0x01) | |
| #define PWR_SLEEPENTRY_WFE ((uint8_t)0x02) | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_STOP_mode_entry PWR STOP mode entry | |
| * @{ | |
| */ | |
| #define PWR_STOPENTRY_WFI ((uint8_t)0x01) | |
| #define PWR_STOPENTRY_WFE ((uint8_t)0x02) | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale | |
| * @{ | |
| */ | |
| #define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR_VOS_0 | |
| #define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR_VOS_1 | |
| #define PWR_REGULATOR_VOLTAGE_SCALE3 PWR_CR_VOS | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PWR_Flag PWR Flag | |
| * @{ | |
| */ | |
| #define PWR_FLAG_WU PWR_CSR_WUF | |
| #define PWR_FLAG_SB PWR_CSR_SBF | |
| #define PWR_FLAG_PVDO PWR_CSR_PVDO | |
| #define PWR_FLAG_VREFINTRDY PWR_CSR_VREFINTRDYF | |
| #define PWR_FLAG_VOS PWR_CSR_VOSF | |
| #define PWR_FLAG_REGLP PWR_CSR_REGLPF | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /* Exported macro ------------------------------------------------------------*/ | |
| /** @defgroup PWR_Exported_Macros PWR Exported Macros | |
| * @{ | |
| */ | |
| /** @brief macros configure the main internal regulator output voltage. | |
| * @param __REGULATOR__ specifies the regulator output voltage to achieve | |
| * a tradeoff between performance and power consumption when the device does | |
| * not operate at the maximum frequency (refer to the datasheets for more details). | |
| * This parameter can be one of the following values: | |
| * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode, | |
| * System frequency up to 32 MHz. | |
| * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode, | |
| * System frequency up to 16 MHz. | |
| * @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode, | |
| * System frequency up to 4.2 MHz | |
| * @retval None | |
| */ | |
| #define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__))) | |
| /** @brief Check PWR flag is set or not. | |
| * @param __FLAG__ specifies the flag to check. | |
| * This parameter can be one of the following values: | |
| * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event | |
| * was received from the WKUP pin or from the RTC alarm (Alarm B), | |
| * RTC Tamper event, RTC TimeStamp event or RTC Wakeup. | |
| * An additional wakeup event is detected if the WKUP pin is enabled | |
| * (by setting the EWUP bit) when the WKUP pin level is already high. | |
| * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was | |
| * resumed from StandBy mode. | |
| * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled | |
| * by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode | |
| * For this reason, this bit is equal to 0 after Standby or reset | |
| * until the PVDE bit is set. | |
| * @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag. | |
| * This bit indicates the state of the internal voltage reference, VREFINT. | |
| * @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for | |
| * the internal regulator to be ready after the voltage range is changed. | |
| * The VOSF bit indicates that the regulator has reached the voltage level | |
| * defined with bits VOS of PWR_CR register. | |
| * @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run | |
| * mode, this bit stays at 1 until the regulator is ready in main mode. | |
| * A polling on this bit is recommended to wait for the regulator main mode. | |
| * This bit is reset by hardware when the regulator is ready. | |
| * @retval The new state of __FLAG__ (TRUE or FALSE). | |
| */ | |
| #define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__)) | |
| /** @brief Clear the PWR's pending flags. | |
| * @param __FLAG__ specifies the flag to clear. | |
| * This parameter can be one of the following values: | |
| * @arg PWR_FLAG_WU: Wake Up flag | |
| * @arg PWR_FLAG_SB: StandBy flag | |
| */ | |
| #define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, ((__FLAG__) << 2)) | |
| /** | |
| * @brief Enable interrupt on PVD Exti Line 16. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief Disable interrupt on PVD Exti Line 16. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief Enable event on PVD Exti Line 16. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief Disable event on PVD Exti Line 16. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief PVD EXTI line configuration: set falling edge trigger. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief Disable the PVD Extended Interrupt Falling Trigger. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief PVD EXTI line configuration: set rising edge trigger. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief Disable the PVD Extended Interrupt Rising Trigger. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @brief PVD EXTI line configuration: set rising & falling edge trigger. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() \ | |
| do { \ | |
| __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); \ | |
| __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); \ | |
| } while(0) | |
| /** | |
| * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() \ | |
| do { \ | |
| __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); \ | |
| __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); \ | |
| } while(0) | |
| /** | |
| * @brief Check whether the specified PVD EXTI interrupt flag is set or not. | |
| * @retval EXTI PVD Line Status. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD)) | |
| /** | |
| * @brief Clear the PVD EXTI flag. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD)) | |
| /** | |
| * @brief Generate a Software interrupt on selected EXTI line. | |
| * @retval None. | |
| */ | |
| #define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD) | |
| /** | |
| * @} | |
| */ | |
| /* Private macro -------------------------------------------------------------*/ | |
| /** @defgroup PWR_Private_Macros PWR Private Macros | |
| * @{ | |
| */ | |
| #define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \ | |
| ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \ | |
| ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \ | |
| ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7)) | |
| #define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \ | |
| ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \ | |
| ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \ | |
| ((MODE) == PWR_PVD_MODE_NORMAL)) | |
| #define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \ | |
| ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON)) | |
| #define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE)) | |
| #define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE) ) | |
| #define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \ | |
| ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \ | |
| ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3)) | |
| /** | |
| * @} | |
| */ | |
| /* Include PWR HAL Extension module */ | |
| #include "stm32l1xx_hal_pwr_ex.h" | |
| /* Exported functions --------------------------------------------------------*/ | |
| /** @addtogroup PWR_Exported_Functions PWR Exported Functions | |
| * @{ | |
| */ | |
| /** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions | |
| * @{ | |
| */ | |
| /* Initialization and de-initialization functions *******************************/ | |
| void HAL_PWR_DeInit(void); | |
| void HAL_PWR_EnableBkUpAccess(void); | |
| void HAL_PWR_DisableBkUpAccess(void); | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions | |
| * @{ | |
| */ | |
| /* Peripheral Control functions ************************************************/ | |
| void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD); | |
| void HAL_PWR_EnablePVD(void); | |
| void HAL_PWR_DisablePVD(void); | |
| /* WakeUp pins configuration functions ****************************************/ | |
| void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx); | |
| void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx); | |
| /* Low Power modes configuration functions ************************************/ | |
| void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry); | |
| void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry); | |
| void HAL_PWR_EnterSTANDBYMode(void); | |
| void HAL_PWR_EnableSleepOnExit(void); | |
| void HAL_PWR_DisableSleepOnExit(void); | |
| void HAL_PWR_EnableSEVOnPend(void); | |
| void HAL_PWR_DisableSEVOnPend(void); | |
| void HAL_PWR_PVD_IRQHandler(void); | |
| void HAL_PWR_PVDCallback(void); | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| #ifdef __cplusplus | |
| } | |
| #endif | |
| #endif /* __STM32L1xx_HAL_PWR_H */ | |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |