| /** |
| ****************************************************************************** |
| * @file stm32f2xx_ll_i2c.h |
| * @author MCD Application Team |
| * @brief Header file of I2C LL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * Copyright (c) 2016 STMicroelectronics. |
| * All rights reserved. |
| * |
| * This software is licensed under terms that can be found in the LICENSE file |
| * in the root directory of this software component. |
| * If no LICENSE file comes with this software, it is provided AS-IS. |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef __STM32F2xx_LL_I2C_H |
| #define __STM32F2xx_LL_I2C_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f2xx.h" |
| |
| /** @addtogroup STM32F2xx_LL_Driver |
| * @{ |
| */ |
| |
| #if defined (I2C1) || defined (I2C2) || defined (I2C3) |
| |
| /** @defgroup I2C_LL I2C |
| * @{ |
| */ |
| |
| /* Private types -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup I2C_LL_Private_Constants I2C Private Constants |
| * @{ |
| */ |
| |
| /* Defines used to perform compute and check in the macros */ |
| #define LL_I2C_MAX_SPEED_STANDARD 100000U |
| #define LL_I2C_MAX_SPEED_FAST 400000U |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| #if defined(USE_FULL_LL_DRIVER) |
| /** @defgroup I2C_LL_Private_Macros I2C Private Macros |
| * @{ |
| */ |
| /** |
| * @} |
| */ |
| #endif /*USE_FULL_LL_DRIVER*/ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| #if defined(USE_FULL_LL_DRIVER) |
| /** @defgroup I2C_LL_ES_INIT I2C Exported Init structure |
| * @{ |
| */ |
| typedef struct |
| { |
| uint32_t PeripheralMode; /*!< Specifies the peripheral mode. |
| This parameter can be a value of @ref I2C_LL_EC_PERIPHERAL_MODE |
| |
| This feature can be modified afterwards using unitary function @ref LL_I2C_SetMode(). */ |
| |
| uint32_t ClockSpeed; /*!< Specifies the clock frequency. |
| This parameter must be set to a value lower than 400kHz (in Hz) |
| |
| This feature can be modified afterwards using unitary function @ref LL_I2C_SetClockPeriod() |
| or @ref LL_I2C_SetDutyCycle() or @ref LL_I2C_SetClockSpeedMode() or @ref LL_I2C_ConfigSpeed(). */ |
| |
| uint32_t DutyCycle; /*!< Specifies the I2C fast mode duty cycle. |
| This parameter can be a value of @ref I2C_LL_EC_DUTYCYCLE |
| |
| This feature can be modified afterwards using unitary function @ref LL_I2C_SetDutyCycle(). */ |
| |
| uint32_t OwnAddress1; /*!< Specifies the device own address 1. |
| This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF |
| |
| This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */ |
| |
| uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. |
| This parameter can be a value of @ref I2C_LL_EC_I2C_ACKNOWLEDGE |
| |
| This feature can be modified afterwards using unitary function @ref LL_I2C_AcknowledgeNextData(). */ |
| |
| uint32_t OwnAddrSize; /*!< Specifies the device own address 1 size (7-bit or 10-bit). |
| This parameter can be a value of @ref I2C_LL_EC_OWNADDRESS1 |
| |
| This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */ |
| } LL_I2C_InitTypeDef; |
| /** |
| * @} |
| */ |
| #endif /*USE_FULL_LL_DRIVER*/ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup I2C_LL_Exported_Constants I2C Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup I2C_LL_EC_GET_FLAG Get Flags Defines |
| * @brief Flags defines which can be used with LL_I2C_ReadReg function |
| * @{ |
| */ |
| #define LL_I2C_SR1_SB I2C_SR1_SB /*!< Start Bit (master mode) */ |
| #define LL_I2C_SR1_ADDR I2C_SR1_ADDR /*!< Address sent (master mode) or |
| Address matched flag (slave mode) */ |
| #define LL_I2C_SR1_BTF I2C_SR1_BTF /*!< Byte Transfer Finished flag */ |
| #define LL_I2C_SR1_ADD10 I2C_SR1_ADD10 /*!< 10-bit header sent (master mode) */ |
| #define LL_I2C_SR1_STOPF I2C_SR1_STOPF /*!< Stop detection flag (slave mode) */ |
| #define LL_I2C_SR1_RXNE I2C_SR1_RXNE /*!< Data register not empty (receivers) */ |
| #define LL_I2C_SR1_TXE I2C_SR1_TXE /*!< Data register empty (transmitters) */ |
| #define LL_I2C_SR1_BERR I2C_SR1_BERR /*!< Bus error */ |
| #define LL_I2C_SR1_ARLO I2C_SR1_ARLO /*!< Arbitration lost */ |
| #define LL_I2C_SR1_AF I2C_SR1_AF /*!< Acknowledge failure flag */ |
| #define LL_I2C_SR1_OVR I2C_SR1_OVR /*!< Overrun/Underrun */ |
| #define LL_I2C_SR1_PECERR I2C_ISR_PECERR /*!< PEC Error in reception (SMBus mode) */ |
| #define LL_I2C_SR1_TIMEOUT I2C_ISR_TIMEOUT /*!< Timeout detection flag (SMBus mode) */ |
| #define LL_I2C_SR1_SMALERT I2C_ISR_SMALERT /*!< SMBus alert (SMBus mode) */ |
| #define LL_I2C_SR2_MSL I2C_SR2_MSL /*!< Master/Slave flag */ |
| #define LL_I2C_SR2_BUSY I2C_SR2_BUSY /*!< Bus busy flag */ |
| #define LL_I2C_SR2_TRA I2C_SR2_TRA /*!< Transmitter/receiver direction */ |
| #define LL_I2C_SR2_GENCALL I2C_SR2_GENCALL /*!< General call address (Slave mode) */ |
| #define LL_I2C_SR2_SMBDEFAULT I2C_SR2_SMBDEFAULT /*!< SMBus Device default address (Slave mode) */ |
| #define LL_I2C_SR2_SMBHOST I2C_SR2_SMBHOST /*!< SMBus Host address (Slave mode) */ |
| #define LL_I2C_SR2_DUALF I2C_SR2_DUALF /*!< Dual flag (Slave mode) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_IT IT Defines |
| * @brief IT defines which can be used with LL_I2C_ReadReg and LL_I2C_WriteReg functions |
| * @{ |
| */ |
| #define LL_I2C_CR2_ITEVTEN I2C_CR2_ITEVTEN /*!< Events interrupts enable */ |
| #define LL_I2C_CR2_ITBUFEN I2C_CR2_ITBUFEN /*!< Buffer interrupts enable */ |
| #define LL_I2C_CR2_ITERREN I2C_CR2_ITERREN /*!< Error interrupts enable */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_OWNADDRESS1 Own Address 1 Length |
| * @{ |
| */ |
| #define LL_I2C_OWNADDRESS1_7BIT 0x00004000U /*!< Own address 1 is a 7-bit address. */ |
| #define LL_I2C_OWNADDRESS1_10BIT (uint32_t)(I2C_OAR1_ADDMODE | 0x00004000U) /*!< Own address 1 is a 10-bit address. */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_DUTYCYCLE Fast Mode Duty Cycle |
| * @{ |
| */ |
| #define LL_I2C_DUTYCYCLE_2 0x00000000U /*!< I2C fast mode Tlow/Thigh = 2 */ |
| #define LL_I2C_DUTYCYCLE_16_9 I2C_CCR_DUTY /*!< I2C fast mode Tlow/Thigh = 16/9 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_CLOCK_SPEED_MODE Master Clock Speed Mode |
| * @{ |
| */ |
| #define LL_I2C_CLOCK_SPEED_STANDARD_MODE 0x00000000U /*!< Master clock speed range is standard mode */ |
| #define LL_I2C_CLOCK_SPEED_FAST_MODE I2C_CCR_FS /*!< Master clock speed range is fast mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_PERIPHERAL_MODE Peripheral Mode |
| * @{ |
| */ |
| #define LL_I2C_MODE_I2C 0x00000000U /*!< I2C Master or Slave mode */ |
| #define LL_I2C_MODE_SMBUS_HOST (uint32_t)(I2C_CR1_SMBUS | I2C_CR1_SMBTYPE | I2C_CR1_ENARP) /*!< SMBus Host address acknowledge */ |
| #define LL_I2C_MODE_SMBUS_DEVICE I2C_CR1_SMBUS /*!< SMBus Device default mode (Default address not acknowledge) */ |
| #define LL_I2C_MODE_SMBUS_DEVICE_ARP (uint32_t)(I2C_CR1_SMBUS | I2C_CR1_ENARP) /*!< SMBus Device Default address acknowledge */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_I2C_ACKNOWLEDGE Acknowledge Generation |
| * @{ |
| */ |
| #define LL_I2C_ACK I2C_CR1_ACK /*!< ACK is sent after current received byte. */ |
| #define LL_I2C_NACK 0x00000000U /*!< NACK is sent after current received byte.*/ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EC_DIRECTION Read Write Direction |
| * @{ |
| */ |
| #define LL_I2C_DIRECTION_WRITE I2C_SR2_TRA /*!< Bus is in write transfer */ |
| #define LL_I2C_DIRECTION_READ 0x00000000U /*!< Bus is in read transfer */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| /** @defgroup I2C_LL_Exported_Macros I2C Exported Macros |
| * @{ |
| */ |
| |
| /** @defgroup I2C_LL_EM_WRITE_READ Common Write and read registers Macros |
| * @{ |
| */ |
| |
| /** |
| * @brief Write a value in I2C register |
| * @param __INSTANCE__ I2C Instance |
| * @param __REG__ Register to be written |
| * @param __VALUE__ Value to be written in the register |
| * @retval None |
| */ |
| #define LL_I2C_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__)) |
| |
| /** |
| * @brief Read a value in I2C register |
| * @param __INSTANCE__ I2C Instance |
| * @param __REG__ Register to be read |
| * @retval Register value |
| */ |
| #define LL_I2C_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EM_Exported_Macros_Helper Exported Macros Helper |
| * @{ |
| */ |
| |
| /** |
| * @brief Convert Peripheral Clock Frequency in Mhz. |
| * @param __PCLK__ This parameter must be a value of peripheral clock (in Hz). |
| * @retval Value of peripheral clock (in Mhz) |
| */ |
| #define __LL_I2C_FREQ_HZ_TO_MHZ(__PCLK__) (uint32_t)((__PCLK__)/1000000U) |
| |
| /** |
| * @brief Convert Peripheral Clock Frequency in Hz. |
| * @param __PCLK__ This parameter must be a value of peripheral clock (in Mhz). |
| * @retval Value of peripheral clock (in Hz) |
| */ |
| #define __LL_I2C_FREQ_MHZ_TO_HZ(__PCLK__) (uint32_t)((__PCLK__)*1000000U) |
| |
| /** |
| * @brief Compute I2C Clock rising time. |
| * @param __FREQRANGE__ This parameter must be a value of peripheral clock (in Mhz). |
| * @param __SPEED__ This parameter must be a value lower than 400kHz (in Hz). |
| * @retval Value between Min_Data=0x02 and Max_Data=0x3F |
| */ |
| #define __LL_I2C_RISE_TIME(__FREQRANGE__, __SPEED__) (uint32_t)(((__SPEED__) <= LL_I2C_MAX_SPEED_STANDARD) ? ((__FREQRANGE__) + 1U) : ((((__FREQRANGE__) * 300U) / 1000U) + 1U)) |
| |
| /** |
| * @brief Compute Speed clock range to a Clock Control Register (I2C_CCR_CCR) value. |
| * @param __PCLK__ This parameter must be a value of peripheral clock (in Hz). |
| * @param __SPEED__ This parameter must be a value lower than 400kHz (in Hz). |
| * @param __DUTYCYCLE__ This parameter can be one of the following values: |
| * @arg @ref LL_I2C_DUTYCYCLE_2 |
| * @arg @ref LL_I2C_DUTYCYCLE_16_9 |
| * @retval Value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001. |
| */ |
| #define __LL_I2C_SPEED_TO_CCR(__PCLK__, __SPEED__, __DUTYCYCLE__) (uint32_t)(((__SPEED__) <= LL_I2C_MAX_SPEED_STANDARD)? \ |
| (__LL_I2C_SPEED_STANDARD_TO_CCR((__PCLK__), (__SPEED__))) : \ |
| (__LL_I2C_SPEED_FAST_TO_CCR((__PCLK__), (__SPEED__), (__DUTYCYCLE__)))) |
| |
| /** |
| * @brief Compute Speed Standard clock range to a Clock Control Register (I2C_CCR_CCR) value. |
| * @param __PCLK__ This parameter must be a value of peripheral clock (in Hz). |
| * @param __SPEED__ This parameter must be a value lower than 100kHz (in Hz). |
| * @retval Value between Min_Data=0x004 and Max_Data=0xFFF. |
| */ |
| #define __LL_I2C_SPEED_STANDARD_TO_CCR(__PCLK__, __SPEED__) (uint32_t)(((((__PCLK__)/((__SPEED__) << 1U)) & I2C_CCR_CCR) < 4U)? 4U:((__PCLK__) / ((__SPEED__) << 1U))) |
| |
| /** |
| * @brief Compute Speed Fast clock range to a Clock Control Register (I2C_CCR_CCR) value. |
| * @param __PCLK__ This parameter must be a value of peripheral clock (in Hz). |
| * @param __SPEED__ This parameter must be a value between Min_Data=100Khz and Max_Data=400Khz (in Hz). |
| * @param __DUTYCYCLE__ This parameter can be one of the following values: |
| * @arg @ref LL_I2C_DUTYCYCLE_2 |
| * @arg @ref LL_I2C_DUTYCYCLE_16_9 |
| * @retval Value between Min_Data=0x001 and Max_Data=0xFFF |
| */ |
| #define __LL_I2C_SPEED_FAST_TO_CCR(__PCLK__, __SPEED__, __DUTYCYCLE__) (uint32_t)(((__DUTYCYCLE__) == LL_I2C_DUTYCYCLE_2)? \ |
| (((((__PCLK__) / ((__SPEED__) * 3U)) & I2C_CCR_CCR) == 0U)? 1U:((__PCLK__) / ((__SPEED__) * 3U))) : \ |
| (((((__PCLK__) / ((__SPEED__) * 25U)) & I2C_CCR_CCR) == 0U)? 1U:((__PCLK__) / ((__SPEED__) * 25U)))) |
| |
| /** |
| * @brief Get the Least significant bits of a 10-Bits address. |
| * @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address. |
| * @retval Value between Min_Data=0x00 and Max_Data=0xFF |
| */ |
| #define __LL_I2C_10BIT_ADDRESS(__ADDRESS__) ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)(0x00FF)))) |
| |
| /** |
| * @brief Convert a 10-Bits address to a 10-Bits header with Write direction. |
| * @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address. |
| * @retval Value between Min_Data=0xF0 and Max_Data=0xF6 |
| */ |
| #define __LL_I2C_10BIT_HEADER_WRITE(__ADDRESS__) ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)(0x0300))) >> 7) | (uint16_t)(0xF0)))) |
| |
| /** |
| * @brief Convert a 10-Bits address to a 10-Bits header with Read direction. |
| * @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address. |
| * @retval Value between Min_Data=0xF1 and Max_Data=0xF7 |
| */ |
| #define __LL_I2C_10BIT_HEADER_READ(__ADDRESS__) ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)(0x0300))) >> 7) | (uint16_t)(0xF1)))) |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| |
| /** @defgroup I2C_LL_Exported_Functions I2C Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup I2C_LL_EF_Configuration Configuration |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable I2C peripheral (PE = 1). |
| * @rmtoll CR1 PE LL_I2C_Enable |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_Enable(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_PE); |
| } |
| |
| /** |
| * @brief Disable I2C peripheral (PE = 0). |
| * @rmtoll CR1 PE LL_I2C_Disable |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_Disable(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_PE); |
| } |
| |
| /** |
| * @brief Check if the I2C peripheral is enabled or disabled. |
| * @rmtoll CR1 PE LL_I2C_IsEnabled |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabled(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_PE) == (I2C_CR1_PE)); |
| } |
| |
| |
| /** |
| * @brief Enable DMA transmission requests. |
| * @rmtoll CR2 DMAEN LL_I2C_EnableDMAReq_TX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableDMAReq_TX(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_DMAEN); |
| } |
| |
| /** |
| * @brief Disable DMA transmission requests. |
| * @rmtoll CR2 DMAEN LL_I2C_DisableDMAReq_TX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableDMAReq_TX(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_DMAEN); |
| } |
| |
| /** |
| * @brief Check if DMA transmission requests are enabled or disabled. |
| * @rmtoll CR2 DMAEN LL_I2C_IsEnabledDMAReq_TX |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_TX(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_DMAEN) == (I2C_CR2_DMAEN)); |
| } |
| |
| /** |
| * @brief Enable DMA reception requests. |
| * @rmtoll CR2 DMAEN LL_I2C_EnableDMAReq_RX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableDMAReq_RX(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_DMAEN); |
| } |
| |
| /** |
| * @brief Disable DMA reception requests. |
| * @rmtoll CR2 DMAEN LL_I2C_DisableDMAReq_RX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableDMAReq_RX(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_DMAEN); |
| } |
| |
| /** |
| * @brief Check if DMA reception requests are enabled or disabled. |
| * @rmtoll CR2 DMAEN LL_I2C_IsEnabledDMAReq_RX |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_RX(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_DMAEN) == (I2C_CR2_DMAEN)); |
| } |
| |
| /** |
| * @brief Get the data register address used for DMA transfer. |
| * @rmtoll DR DR LL_I2C_DMA_GetRegAddr |
| * @param I2Cx I2C Instance. |
| * @retval Address of data register |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_DMA_GetRegAddr(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t) & (I2Cx->DR); |
| } |
| |
| /** |
| * @brief Enable Clock stretching. |
| * @note This bit can only be programmed when the I2C is disabled (PE = 0). |
| * @rmtoll CR1 NOSTRETCH LL_I2C_EnableClockStretching |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableClockStretching(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH); |
| } |
| |
| /** |
| * @brief Disable Clock stretching. |
| * @note This bit can only be programmed when the I2C is disabled (PE = 0). |
| * @rmtoll CR1 NOSTRETCH LL_I2C_DisableClockStretching |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableClockStretching(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH); |
| } |
| |
| /** |
| * @brief Check if Clock stretching is enabled or disabled. |
| * @rmtoll CR1 NOSTRETCH LL_I2C_IsEnabledClockStretching |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledClockStretching(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH) != (I2C_CR1_NOSTRETCH)); |
| } |
| |
| /** |
| * @brief Enable General Call. |
| * @note When enabled the Address 0x00 is ACKed. |
| * @rmtoll CR1 ENGC LL_I2C_EnableGeneralCall |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableGeneralCall(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_ENGC); |
| } |
| |
| /** |
| * @brief Disable General Call. |
| * @note When disabled the Address 0x00 is NACKed. |
| * @rmtoll CR1 ENGC LL_I2C_DisableGeneralCall |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableGeneralCall(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_ENGC); |
| } |
| |
| /** |
| * @brief Check if General Call is enabled or disabled. |
| * @rmtoll CR1 ENGC LL_I2C_IsEnabledGeneralCall |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledGeneralCall(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_ENGC) == (I2C_CR1_ENGC)); |
| } |
| |
| /** |
| * @brief Set the Own Address1. |
| * @rmtoll OAR1 ADD0 LL_I2C_SetOwnAddress1\n |
| * OAR1 ADD1_7 LL_I2C_SetOwnAddress1\n |
| * OAR1 ADD8_9 LL_I2C_SetOwnAddress1\n |
| * OAR1 ADDMODE LL_I2C_SetOwnAddress1 |
| * @param I2Cx I2C Instance. |
| * @param OwnAddress1 This parameter must be a value between Min_Data=0 and Max_Data=0x3FF. |
| * @param OwnAddrSize This parameter can be one of the following values: |
| * @arg @ref LL_I2C_OWNADDRESS1_7BIT |
| * @arg @ref LL_I2C_OWNADDRESS1_10BIT |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetOwnAddress1(I2C_TypeDef *I2Cx, uint32_t OwnAddress1, uint32_t OwnAddrSize) |
| { |
| MODIFY_REG(I2Cx->OAR1, I2C_OAR1_ADD0 | I2C_OAR1_ADD1_7 | I2C_OAR1_ADD8_9 | I2C_OAR1_ADDMODE, OwnAddress1 | OwnAddrSize); |
| } |
| |
| /** |
| * @brief Set the 7bits Own Address2. |
| * @note This action has no effect if own address2 is enabled. |
| * @rmtoll OAR2 ADD2 LL_I2C_SetOwnAddress2 |
| * @param I2Cx I2C Instance. |
| * @param OwnAddress2 This parameter must be a value between Min_Data=0 and Max_Data=0x7F. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetOwnAddress2(I2C_TypeDef *I2Cx, uint32_t OwnAddress2) |
| { |
| MODIFY_REG(I2Cx->OAR2, I2C_OAR2_ADD2, OwnAddress2); |
| } |
| |
| /** |
| * @brief Enable acknowledge on Own Address2 match address. |
| * @rmtoll OAR2 ENDUAL LL_I2C_EnableOwnAddress2 |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableOwnAddress2(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL); |
| } |
| |
| /** |
| * @brief Disable acknowledge on Own Address2 match address. |
| * @rmtoll OAR2 ENDUAL LL_I2C_DisableOwnAddress2 |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableOwnAddress2(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL); |
| } |
| |
| /** |
| * @brief Check if Own Address1 acknowledge is enabled or disabled. |
| * @rmtoll OAR2 ENDUAL LL_I2C_IsEnabledOwnAddress2 |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress2(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL) == (I2C_OAR2_ENDUAL)); |
| } |
| |
| /** |
| * @brief Configure the Peripheral clock frequency. |
| * @rmtoll CR2 FREQ LL_I2C_SetPeriphClock |
| * @param I2Cx I2C Instance. |
| * @param PeriphClock Peripheral Clock (in Hz) |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetPeriphClock(I2C_TypeDef *I2Cx, uint32_t PeriphClock) |
| { |
| MODIFY_REG(I2Cx->CR2, I2C_CR2_FREQ, __LL_I2C_FREQ_HZ_TO_MHZ(PeriphClock)); |
| } |
| |
| /** |
| * @brief Get the Peripheral clock frequency. |
| * @rmtoll CR2 FREQ LL_I2C_GetPeriphClock |
| * @param I2Cx I2C Instance. |
| * @retval Value of Peripheral Clock (in Hz) |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetPeriphClock(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(__LL_I2C_FREQ_MHZ_TO_HZ(READ_BIT(I2Cx->CR2, I2C_CR2_FREQ))); |
| } |
| |
| /** |
| * @brief Configure the Duty cycle (Fast mode only). |
| * @rmtoll CCR DUTY LL_I2C_SetDutyCycle |
| * @param I2Cx I2C Instance. |
| * @param DutyCycle This parameter can be one of the following values: |
| * @arg @ref LL_I2C_DUTYCYCLE_2 |
| * @arg @ref LL_I2C_DUTYCYCLE_16_9 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetDutyCycle(I2C_TypeDef *I2Cx, uint32_t DutyCycle) |
| { |
| MODIFY_REG(I2Cx->CCR, I2C_CCR_DUTY, DutyCycle); |
| } |
| |
| /** |
| * @brief Get the Duty cycle (Fast mode only). |
| * @rmtoll CCR DUTY LL_I2C_GetDutyCycle |
| * @param I2Cx I2C Instance. |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_I2C_DUTYCYCLE_2 |
| * @arg @ref LL_I2C_DUTYCYCLE_16_9 |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetDutyCycle(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_DUTY)); |
| } |
| |
| /** |
| * @brief Configure the I2C master clock speed mode. |
| * @rmtoll CCR FS LL_I2C_SetClockSpeedMode |
| * @param I2Cx I2C Instance. |
| * @param ClockSpeedMode This parameter can be one of the following values: |
| * @arg @ref LL_I2C_CLOCK_SPEED_STANDARD_MODE |
| * @arg @ref LL_I2C_CLOCK_SPEED_FAST_MODE |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetClockSpeedMode(I2C_TypeDef *I2Cx, uint32_t ClockSpeedMode) |
| { |
| MODIFY_REG(I2Cx->CCR, I2C_CCR_FS, ClockSpeedMode); |
| } |
| |
| /** |
| * @brief Get the the I2C master speed mode. |
| * @rmtoll CCR FS LL_I2C_GetClockSpeedMode |
| * @param I2Cx I2C Instance. |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_I2C_CLOCK_SPEED_STANDARD_MODE |
| * @arg @ref LL_I2C_CLOCK_SPEED_FAST_MODE |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetClockSpeedMode(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_FS)); |
| } |
| |
| /** |
| * @brief Configure the SCL, SDA rising time. |
| * @note This bit can only be programmed when the I2C is disabled (PE = 0). |
| * @rmtoll TRISE TRISE LL_I2C_SetRiseTime |
| * @param I2Cx I2C Instance. |
| * @param RiseTime This parameter must be a value between Min_Data=0x02 and Max_Data=0x3F. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetRiseTime(I2C_TypeDef *I2Cx, uint32_t RiseTime) |
| { |
| MODIFY_REG(I2Cx->TRISE, I2C_TRISE_TRISE, RiseTime); |
| } |
| |
| /** |
| * @brief Get the SCL, SDA rising time. |
| * @rmtoll TRISE TRISE LL_I2C_GetRiseTime |
| * @param I2Cx I2C Instance. |
| * @retval Value between Min_Data=0x02 and Max_Data=0x3F |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetRiseTime(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->TRISE, I2C_TRISE_TRISE)); |
| } |
| |
| /** |
| * @brief Configure the SCL high and low period. |
| * @note This bit can only be programmed when the I2C is disabled (PE = 0). |
| * @rmtoll CCR CCR LL_I2C_SetClockPeriod |
| * @param I2Cx I2C Instance. |
| * @param ClockPeriod This parameter must be a value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetClockPeriod(I2C_TypeDef *I2Cx, uint32_t ClockPeriod) |
| { |
| MODIFY_REG(I2Cx->CCR, I2C_CCR_CCR, ClockPeriod); |
| } |
| |
| /** |
| * @brief Get the SCL high and low period. |
| * @rmtoll CCR CCR LL_I2C_GetClockPeriod |
| * @param I2Cx I2C Instance. |
| * @retval Value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001. |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetClockPeriod(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_CCR)); |
| } |
| |
| /** |
| * @brief Configure the SCL speed. |
| * @note This bit can only be programmed when the I2C is disabled (PE = 0). |
| * @rmtoll CR2 FREQ LL_I2C_ConfigSpeed\n |
| * TRISE TRISE LL_I2C_ConfigSpeed\n |
| * CCR FS LL_I2C_ConfigSpeed\n |
| * CCR DUTY LL_I2C_ConfigSpeed\n |
| * CCR CCR LL_I2C_ConfigSpeed |
| * @param I2Cx I2C Instance. |
| * @param PeriphClock Peripheral Clock (in Hz) |
| * @param ClockSpeed This parameter must be a value lower than 400kHz (in Hz). |
| * @param DutyCycle This parameter can be one of the following values: |
| * @arg @ref LL_I2C_DUTYCYCLE_2 |
| * @arg @ref LL_I2C_DUTYCYCLE_16_9 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ConfigSpeed(I2C_TypeDef *I2Cx, uint32_t PeriphClock, uint32_t ClockSpeed, |
| uint32_t DutyCycle) |
| { |
| uint32_t freqrange = 0x0U; |
| uint32_t clockconfig = 0x0U; |
| |
| /* Compute frequency range */ |
| freqrange = __LL_I2C_FREQ_HZ_TO_MHZ(PeriphClock); |
| |
| /* Configure I2Cx: Frequency range register */ |
| MODIFY_REG(I2Cx->CR2, I2C_CR2_FREQ, freqrange); |
| |
| /* Configure I2Cx: Rise Time register */ |
| MODIFY_REG(I2Cx->TRISE, I2C_TRISE_TRISE, __LL_I2C_RISE_TIME(freqrange, ClockSpeed)); |
| |
| /* Configure Speed mode, Duty Cycle and Clock control register value */ |
| if (ClockSpeed > LL_I2C_MAX_SPEED_STANDARD) |
| { |
| /* Set Speed mode at fast and duty cycle for Clock Speed request in fast clock range */ |
| clockconfig = LL_I2C_CLOCK_SPEED_FAST_MODE | \ |
| __LL_I2C_SPEED_FAST_TO_CCR(PeriphClock, ClockSpeed, DutyCycle) | \ |
| DutyCycle; |
| } |
| else |
| { |
| /* Set Speed mode at standard for Clock Speed request in standard clock range */ |
| clockconfig = LL_I2C_CLOCK_SPEED_STANDARD_MODE | \ |
| __LL_I2C_SPEED_STANDARD_TO_CCR(PeriphClock, ClockSpeed); |
| } |
| |
| /* Configure I2Cx: Clock control register */ |
| MODIFY_REG(I2Cx->CCR, (I2C_CCR_FS | I2C_CCR_DUTY | I2C_CCR_CCR), clockconfig); |
| } |
| |
| /** |
| * @brief Configure peripheral mode. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 SMBUS LL_I2C_SetMode\n |
| * CR1 SMBTYPE LL_I2C_SetMode\n |
| * CR1 ENARP LL_I2C_SetMode |
| * @param I2Cx I2C Instance. |
| * @param PeripheralMode This parameter can be one of the following values: |
| * @arg @ref LL_I2C_MODE_I2C |
| * @arg @ref LL_I2C_MODE_SMBUS_HOST |
| * @arg @ref LL_I2C_MODE_SMBUS_DEVICE |
| * @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_SetMode(I2C_TypeDef *I2Cx, uint32_t PeripheralMode) |
| { |
| MODIFY_REG(I2Cx->CR1, I2C_CR1_SMBUS | I2C_CR1_SMBTYPE | I2C_CR1_ENARP, PeripheralMode); |
| } |
| |
| /** |
| * @brief Get peripheral mode. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 SMBUS LL_I2C_GetMode\n |
| * CR1 SMBTYPE LL_I2C_GetMode\n |
| * CR1 ENARP LL_I2C_GetMode |
| * @param I2Cx I2C Instance. |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_I2C_MODE_I2C |
| * @arg @ref LL_I2C_MODE_SMBUS_HOST |
| * @arg @ref LL_I2C_MODE_SMBUS_DEVICE |
| * @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetMode(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_SMBUS | I2C_CR1_SMBTYPE | I2C_CR1_ENARP)); |
| } |
| |
| /** |
| * @brief Enable SMBus alert (Host or Device mode) |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note SMBus Device mode: |
| * - SMBus Alert pin is drived low and |
| * Alert Response Address Header acknowledge is enabled. |
| * SMBus Host mode: |
| * - SMBus Alert pin management is supported. |
| * @rmtoll CR1 ALERT LL_I2C_EnableSMBusAlert |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableSMBusAlert(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_ALERT); |
| } |
| |
| /** |
| * @brief Disable SMBus alert (Host or Device mode) |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note SMBus Device mode: |
| * - SMBus Alert pin is not drived (can be used as a standard GPIO) and |
| * Alert Response Address Header acknowledge is disabled. |
| * SMBus Host mode: |
| * - SMBus Alert pin management is not supported. |
| * @rmtoll CR1 ALERT LL_I2C_DisableSMBusAlert |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableSMBusAlert(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_ALERT); |
| } |
| |
| /** |
| * @brief Check if SMBus alert (Host or Device mode) is enabled or disabled. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 ALERT LL_I2C_IsEnabledSMBusAlert |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusAlert(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_ALERT) == (I2C_CR1_ALERT)); |
| } |
| |
| /** |
| * @brief Enable SMBus Packet Error Calculation (PEC). |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 ENPEC LL_I2C_EnableSMBusPEC |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableSMBusPEC(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_ENPEC); |
| } |
| |
| /** |
| * @brief Disable SMBus Packet Error Calculation (PEC). |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 ENPEC LL_I2C_DisableSMBusPEC |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableSMBusPEC(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_ENPEC); |
| } |
| |
| /** |
| * @brief Check if SMBus Packet Error Calculation (PEC) is enabled or disabled. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 ENPEC LL_I2C_IsEnabledSMBusPEC |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPEC(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_ENPEC) == (I2C_CR1_ENPEC)); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EF_IT_Management IT_Management |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable TXE interrupt. |
| * @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_TX\n |
| * CR2 ITBUFEN LL_I2C_EnableIT_TX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableIT_TX(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN); |
| } |
| |
| /** |
| * @brief Disable TXE interrupt. |
| * @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_TX\n |
| * CR2 ITBUFEN LL_I2C_DisableIT_TX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableIT_TX(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN); |
| } |
| |
| /** |
| * @brief Check if the TXE Interrupt is enabled or disabled. |
| * @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_TX\n |
| * CR2 ITBUFEN LL_I2C_IsEnabledIT_TX |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TX(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN) == (I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN)); |
| } |
| |
| /** |
| * @brief Enable RXNE interrupt. |
| * @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_RX\n |
| * CR2 ITBUFEN LL_I2C_EnableIT_RX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableIT_RX(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN); |
| } |
| |
| /** |
| * @brief Disable RXNE interrupt. |
| * @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_RX\n |
| * CR2 ITBUFEN LL_I2C_DisableIT_RX |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableIT_RX(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN); |
| } |
| |
| /** |
| * @brief Check if the RXNE Interrupt is enabled or disabled. |
| * @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_RX\n |
| * CR2 ITBUFEN LL_I2C_IsEnabledIT_RX |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_RX(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN) == (I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN)); |
| } |
| |
| /** |
| * @brief Enable Events interrupts. |
| * @note Any of these events will generate interrupt : |
| * Start Bit (SB) |
| * Address sent, Address matched (ADDR) |
| * 10-bit header sent (ADD10) |
| * Stop detection (STOPF) |
| * Byte transfer finished (BTF) |
| * |
| * @note Any of these events will generate interrupt if Buffer interrupts are enabled too(using unitary function @ref LL_I2C_EnableIT_BUF()) : |
| * Receive buffer not empty (RXNE) |
| * Transmit buffer empty (TXE) |
| * @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_EVT |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableIT_EVT(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN); |
| } |
| |
| /** |
| * @brief Disable Events interrupts. |
| * @note Any of these events will generate interrupt : |
| * Start Bit (SB) |
| * Address sent, Address matched (ADDR) |
| * 10-bit header sent (ADD10) |
| * Stop detection (STOPF) |
| * Byte transfer finished (BTF) |
| * Receive buffer not empty (RXNE) |
| * Transmit buffer empty (TXE) |
| * @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_EVT |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableIT_EVT(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN); |
| } |
| |
| /** |
| * @brief Check if Events interrupts are enabled or disabled. |
| * @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_EVT |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_EVT(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN) == (I2C_CR2_ITEVTEN)); |
| } |
| |
| /** |
| * @brief Enable Buffer interrupts. |
| * @note Any of these Buffer events will generate interrupt if Events interrupts are enabled too(using unitary function @ref LL_I2C_EnableIT_EVT()) : |
| * Receive buffer not empty (RXNE) |
| * Transmit buffer empty (TXE) |
| * @rmtoll CR2 ITBUFEN LL_I2C_EnableIT_BUF |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableIT_BUF(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN); |
| } |
| |
| /** |
| * @brief Disable Buffer interrupts. |
| * @note Any of these Buffer events will generate interrupt : |
| * Receive buffer not empty (RXNE) |
| * Transmit buffer empty (TXE) |
| * @rmtoll CR2 ITBUFEN LL_I2C_DisableIT_BUF |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableIT_BUF(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN); |
| } |
| |
| /** |
| * @brief Check if Buffer interrupts are enabled or disabled. |
| * @rmtoll CR2 ITBUFEN LL_I2C_IsEnabledIT_BUF |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_BUF(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN) == (I2C_CR2_ITBUFEN)); |
| } |
| |
| /** |
| * @brief Enable Error interrupts. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note Any of these errors will generate interrupt : |
| * Bus Error detection (BERR) |
| * Arbitration Loss (ARLO) |
| * Acknowledge Failure(AF) |
| * Overrun/Underrun (OVR) |
| * SMBus Timeout detection (TIMEOUT) |
| * SMBus PEC error detection (PECERR) |
| * SMBus Alert pin event detection (SMBALERT) |
| * @rmtoll CR2 ITERREN LL_I2C_EnableIT_ERR |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableIT_ERR(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_ITERREN); |
| } |
| |
| /** |
| * @brief Disable Error interrupts. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note Any of these errors will generate interrupt : |
| * Bus Error detection (BERR) |
| * Arbitration Loss (ARLO) |
| * Acknowledge Failure(AF) |
| * Overrun/Underrun (OVR) |
| * SMBus Timeout detection (TIMEOUT) |
| * SMBus PEC error detection (PECERR) |
| * SMBus Alert pin event detection (SMBALERT) |
| * @rmtoll CR2 ITERREN LL_I2C_DisableIT_ERR |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableIT_ERR(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITERREN); |
| } |
| |
| /** |
| * @brief Check if Error interrupts are enabled or disabled. |
| * @rmtoll CR2 ITERREN LL_I2C_IsEnabledIT_ERR |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ERR(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_ITERREN) == (I2C_CR2_ITERREN)); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EF_FLAG_management FLAG_management |
| * @{ |
| */ |
| |
| /** |
| * @brief Indicate the status of Transmit data register empty flag. |
| * @note RESET: When next data is written in Transmit data register. |
| * SET: When Transmit data register is empty. |
| * @rmtoll SR1 TXE LL_I2C_IsActiveFlag_TXE |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXE(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_TXE) == (I2C_SR1_TXE)); |
| } |
| |
| /** |
| * @brief Indicate the status of Byte Transfer Finished flag. |
| * RESET: When Data byte transfer not done. |
| * SET: When Data byte transfer succeeded. |
| * @rmtoll SR1 BTF LL_I2C_IsActiveFlag_BTF |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BTF(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_BTF) == (I2C_SR1_BTF)); |
| } |
| |
| /** |
| * @brief Indicate the status of Receive data register not empty flag. |
| * @note RESET: When Receive data register is read. |
| * SET: When the received data is copied in Receive data register. |
| * @rmtoll SR1 RXNE LL_I2C_IsActiveFlag_RXNE |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_RXNE(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_RXNE) == (I2C_SR1_RXNE)); |
| } |
| |
| /** |
| * @brief Indicate the status of Start Bit (master mode). |
| * @note RESET: When No Start condition. |
| * SET: When Start condition is generated. |
| * @rmtoll SR1 SB LL_I2C_IsActiveFlag_SB |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_SB(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_SB) == (I2C_SR1_SB)); |
| } |
| |
| /** |
| * @brief Indicate the status of Address sent (master mode) or Address matched flag (slave mode). |
| * @note RESET: Clear default value. |
| * SET: When the address is fully sent (master mode) or when the received slave address matched with one of the enabled slave address (slave mode). |
| * @rmtoll SR1 ADDR LL_I2C_IsActiveFlag_ADDR |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADDR(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_ADDR) == (I2C_SR1_ADDR)); |
| } |
| |
| /** |
| * @brief Indicate the status of 10-bit header sent (master mode). |
| * @note RESET: When no ADD10 event occurred. |
| * SET: When the master has sent the first address byte (header). |
| * @rmtoll SR1 ADD10 LL_I2C_IsActiveFlag_ADD10 |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADD10(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_ADD10) == (I2C_SR1_ADD10)); |
| } |
| |
| /** |
| * @brief Indicate the status of Acknowledge failure flag. |
| * @note RESET: No acknowledge failure. |
| * SET: When an acknowledge failure is received after a byte transmission. |
| * @rmtoll SR1 AF LL_I2C_IsActiveFlag_AF |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_AF(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_AF) == (I2C_SR1_AF)); |
| } |
| |
| /** |
| * @brief Indicate the status of Stop detection flag (slave mode). |
| * @note RESET: Clear default value. |
| * SET: When a Stop condition is detected. |
| * @rmtoll SR1 STOPF LL_I2C_IsActiveFlag_STOP |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_STOP(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_STOPF) == (I2C_SR1_STOPF)); |
| } |
| |
| /** |
| * @brief Indicate the status of Bus error flag. |
| * @note RESET: Clear default value. |
| * SET: When a misplaced Start or Stop condition is detected. |
| * @rmtoll SR1 BERR LL_I2C_IsActiveFlag_BERR |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BERR(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_BERR) == (I2C_SR1_BERR)); |
| } |
| |
| /** |
| * @brief Indicate the status of Arbitration lost flag. |
| * @note RESET: Clear default value. |
| * SET: When arbitration lost. |
| * @rmtoll SR1 ARLO LL_I2C_IsActiveFlag_ARLO |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ARLO(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_ARLO) == (I2C_SR1_ARLO)); |
| } |
| |
| /** |
| * @brief Indicate the status of Overrun/Underrun flag. |
| * @note RESET: Clear default value. |
| * SET: When an overrun/underrun error occurs (Clock Stretching Disabled). |
| * @rmtoll SR1 OVR LL_I2C_IsActiveFlag_OVR |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_OVR(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_OVR) == (I2C_SR1_OVR)); |
| } |
| |
| /** |
| * @brief Indicate the status of SMBus PEC error flag in reception. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll SR1 PECERR LL_I2C_IsActiveSMBusFlag_PECERR |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_PECERR(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_PECERR) == (I2C_SR1_PECERR)); |
| } |
| |
| /** |
| * @brief Indicate the status of SMBus Timeout detection flag. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll SR1 TIMEOUT LL_I2C_IsActiveSMBusFlag_TIMEOUT |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_TIMEOUT) == (I2C_SR1_TIMEOUT)); |
| } |
| |
| /** |
| * @brief Indicate the status of SMBus alert flag. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll SR1 SMBALERT LL_I2C_IsActiveSMBusFlag_ALERT |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_ALERT(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR1, I2C_SR1_SMBALERT) == (I2C_SR1_SMBALERT)); |
| } |
| |
| /** |
| * @brief Indicate the status of Bus Busy flag. |
| * @note RESET: Clear default value. |
| * SET: When a Start condition is detected. |
| * @rmtoll SR2 BUSY LL_I2C_IsActiveFlag_BUSY |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BUSY(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR2, I2C_SR2_BUSY) == (I2C_SR2_BUSY)); |
| } |
| |
| /** |
| * @brief Indicate the status of Dual flag. |
| * @note RESET: Received address matched with OAR1. |
| * SET: Received address matched with OAR2. |
| * @rmtoll SR2 DUALF LL_I2C_IsActiveFlag_DUAL |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_DUAL(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR2, I2C_SR2_DUALF) == (I2C_SR2_DUALF)); |
| } |
| |
| /** |
| * @brief Indicate the status of SMBus Host address reception (Slave mode). |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note RESET: No SMBus Host address |
| * SET: SMBus Host address received. |
| * @note This status is cleared by hardware after a STOP condition or repeated START condition. |
| * @rmtoll SR2 SMBHOST LL_I2C_IsActiveSMBusFlag_SMBHOST |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_SMBHOST(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR2, I2C_SR2_SMBHOST) == (I2C_SR2_SMBHOST)); |
| } |
| |
| /** |
| * @brief Indicate the status of SMBus Device default address reception (Slave mode). |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note RESET: No SMBus Device default address |
| * SET: SMBus Device default address received. |
| * @note This status is cleared by hardware after a STOP condition or repeated START condition. |
| * @rmtoll SR2 SMBDEFAULT LL_I2C_IsActiveSMBusFlag_SMBDEFAULT |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_SMBDEFAULT(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR2, I2C_SR2_SMBDEFAULT) == (I2C_SR2_SMBDEFAULT)); |
| } |
| |
| /** |
| * @brief Indicate the status of General call address reception (Slave mode). |
| * @note RESET: No General call address |
| * SET: General call address received. |
| * @note This status is cleared by hardware after a STOP condition or repeated START condition. |
| * @rmtoll SR2 GENCALL LL_I2C_IsActiveFlag_GENCALL |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_GENCALL(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR2, I2C_SR2_GENCALL) == (I2C_SR2_GENCALL)); |
| } |
| |
| /** |
| * @brief Indicate the status of Master/Slave flag. |
| * @note RESET: Slave Mode. |
| * SET: Master Mode. |
| * @rmtoll SR2 MSL LL_I2C_IsActiveFlag_MSL |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_MSL(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->SR2, I2C_SR2_MSL) == (I2C_SR2_MSL)); |
| } |
| |
| /** |
| * @brief Clear Address Matched flag. |
| * @note Clearing this flag is done by a read access to the I2Cx_SR1 |
| * register followed by a read access to the I2Cx_SR2 register. |
| * @rmtoll SR1 ADDR LL_I2C_ClearFlag_ADDR |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearFlag_ADDR(I2C_TypeDef *I2Cx) |
| { |
| __IO uint32_t tmpreg; |
| tmpreg = I2Cx->SR1; |
| (void) tmpreg; |
| tmpreg = I2Cx->SR2; |
| (void) tmpreg; |
| } |
| |
| /** |
| * @brief Clear Acknowledge failure flag. |
| * @rmtoll SR1 AF LL_I2C_ClearFlag_AF |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearFlag_AF(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_AF); |
| } |
| |
| /** |
| * @brief Clear Stop detection flag. |
| * @note Clearing this flag is done by a read access to the I2Cx_SR1 |
| * register followed by a write access to I2Cx_CR1 register. |
| * @rmtoll SR1 STOPF LL_I2C_ClearFlag_STOP\n |
| * CR1 PE LL_I2C_ClearFlag_STOP |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearFlag_STOP(I2C_TypeDef *I2Cx) |
| { |
| __IO uint32_t tmpreg; |
| tmpreg = I2Cx->SR1; |
| (void) tmpreg; |
| SET_BIT(I2Cx->CR1, I2C_CR1_PE); |
| } |
| |
| /** |
| * @brief Clear Bus error flag. |
| * @rmtoll SR1 BERR LL_I2C_ClearFlag_BERR |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearFlag_BERR(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_BERR); |
| } |
| |
| /** |
| * @brief Clear Arbitration lost flag. |
| * @rmtoll SR1 ARLO LL_I2C_ClearFlag_ARLO |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearFlag_ARLO(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_ARLO); |
| } |
| |
| /** |
| * @brief Clear Overrun/Underrun flag. |
| * @rmtoll SR1 OVR LL_I2C_ClearFlag_OVR |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearFlag_OVR(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_OVR); |
| } |
| |
| /** |
| * @brief Clear SMBus PEC error flag. |
| * @rmtoll SR1 PECERR LL_I2C_ClearSMBusFlag_PECERR |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearSMBusFlag_PECERR(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_PECERR); |
| } |
| |
| /** |
| * @brief Clear SMBus Timeout detection flag. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll SR1 TIMEOUT LL_I2C_ClearSMBusFlag_TIMEOUT |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_TIMEOUT); |
| } |
| |
| /** |
| * @brief Clear SMBus Alert flag. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll SR1 SMBALERT LL_I2C_ClearSMBusFlag_ALERT |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_ClearSMBusFlag_ALERT(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->SR1, I2C_SR1_SMBALERT); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup I2C_LL_EF_Data_Management Data_Management |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable Reset of I2C peripheral. |
| * @rmtoll CR1 SWRST LL_I2C_EnableReset |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableReset(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_SWRST); |
| } |
| |
| /** |
| * @brief Disable Reset of I2C peripheral. |
| * @rmtoll CR1 SWRST LL_I2C_DisableReset |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableReset(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_SWRST); |
| } |
| |
| /** |
| * @brief Check if the I2C peripheral is under reset state or not. |
| * @rmtoll CR1 SWRST LL_I2C_IsResetEnabled |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsResetEnabled(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_SWRST) == (I2C_CR1_SWRST)); |
| } |
| |
| /** |
| * @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. |
| * @note Usage in Slave or Master mode. |
| * @rmtoll CR1 ACK LL_I2C_AcknowledgeNextData |
| * @param I2Cx I2C Instance. |
| * @param TypeAcknowledge This parameter can be one of the following values: |
| * @arg @ref LL_I2C_ACK |
| * @arg @ref LL_I2C_NACK |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_AcknowledgeNextData(I2C_TypeDef *I2Cx, uint32_t TypeAcknowledge) |
| { |
| MODIFY_REG(I2Cx->CR1, I2C_CR1_ACK, TypeAcknowledge); |
| } |
| |
| /** |
| * @brief Generate a START or RESTART condition |
| * @note The START bit can be set even if bus is BUSY or I2C is in slave mode. |
| * This action has no effect when RELOAD is set. |
| * @rmtoll CR1 START LL_I2C_GenerateStartCondition |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_GenerateStartCondition(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_START); |
| } |
| |
| /** |
| * @brief Generate a STOP condition after the current byte transfer (master mode). |
| * @rmtoll CR1 STOP LL_I2C_GenerateStopCondition |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_GenerateStopCondition(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_STOP); |
| } |
| |
| /** |
| * @brief Enable bit POS (master/host mode). |
| * @note In that case, the ACK bit controls the (N)ACK of the next byte received or the PEC bit indicates that the next byte in shift register is a PEC. |
| * @rmtoll CR1 POS LL_I2C_EnableBitPOS |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableBitPOS(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_POS); |
| } |
| |
| /** |
| * @brief Disable bit POS (master/host mode). |
| * @note In that case, the ACK bit controls the (N)ACK of the current byte received or the PEC bit indicates that the current byte in shift register is a PEC. |
| * @rmtoll CR1 POS LL_I2C_DisableBitPOS |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableBitPOS(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_POS); |
| } |
| |
| /** |
| * @brief Check if bit POS is enabled or disabled. |
| * @rmtoll CR1 POS LL_I2C_IsEnabledBitPOS |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledBitPOS(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_POS) == (I2C_CR1_POS)); |
| } |
| |
| /** |
| * @brief Indicate the value of transfer direction. |
| * @note RESET: Bus is in read transfer (peripheral point of view). |
| * SET: Bus is in write transfer (peripheral point of view). |
| * @rmtoll SR2 TRA LL_I2C_GetTransferDirection |
| * @param I2Cx I2C Instance. |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_I2C_DIRECTION_WRITE |
| * @arg @ref LL_I2C_DIRECTION_READ |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetTransferDirection(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->SR2, I2C_SR2_TRA)); |
| } |
| |
| /** |
| * @brief Enable DMA last transfer. |
| * @note This action mean that next DMA EOT is the last transfer. |
| * @rmtoll CR2 LAST LL_I2C_EnableLastDMA |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableLastDMA(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR2, I2C_CR2_LAST); |
| } |
| |
| /** |
| * @brief Disable DMA last transfer. |
| * @note This action mean that next DMA EOT is not the last transfer. |
| * @rmtoll CR2 LAST LL_I2C_DisableLastDMA |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableLastDMA(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR2, I2C_CR2_LAST); |
| } |
| |
| /** |
| * @brief Check if DMA last transfer is enabled or disabled. |
| * @rmtoll CR2 LAST LL_I2C_IsEnabledLastDMA |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledLastDMA(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR2, I2C_CR2_LAST) == (I2C_CR2_LAST)); |
| } |
| |
| /** |
| * @brief Enable transfer or internal comparison of the SMBus Packet Error byte (transmission or reception mode). |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @note This feature is cleared by hardware when the PEC byte is transferred or compared, |
| * or by a START or STOP condition, it is also cleared by software. |
| * @rmtoll CR1 PEC LL_I2C_EnableSMBusPECCompare |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_EnableSMBusPECCompare(I2C_TypeDef *I2Cx) |
| { |
| SET_BIT(I2Cx->CR1, I2C_CR1_PEC); |
| } |
| |
| /** |
| * @brief Disable transfer or internal comparison of the SMBus Packet Error byte (transmission or reception mode). |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 PEC LL_I2C_DisableSMBusPECCompare |
| * @param I2Cx I2C Instance. |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_DisableSMBusPECCompare(I2C_TypeDef *I2Cx) |
| { |
| CLEAR_BIT(I2Cx->CR1, I2C_CR1_PEC); |
| } |
| |
| /** |
| * @brief Check if the SMBus Packet Error byte transfer or internal comparison is requested or not. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll CR1 PEC LL_I2C_IsEnabledSMBusPECCompare |
| * @param I2Cx I2C Instance. |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPECCompare(I2C_TypeDef *I2Cx) |
| { |
| return (READ_BIT(I2Cx->CR1, I2C_CR1_PEC) == (I2C_CR1_PEC)); |
| } |
| |
| /** |
| * @brief Get the SMBus Packet Error byte calculated. |
| * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not |
| * SMBus feature is supported by the I2Cx Instance. |
| * @rmtoll SR2 PEC LL_I2C_GetSMBusPEC |
| * @param I2Cx I2C Instance. |
| * @retval Value between Min_Data=0x00 and Max_Data=0xFF |
| */ |
| __STATIC_INLINE uint32_t LL_I2C_GetSMBusPEC(I2C_TypeDef *I2Cx) |
| { |
| return (uint32_t)(READ_BIT(I2Cx->SR2, I2C_SR2_PEC) >> I2C_SR2_PEC_Pos); |
| } |
| |
| /** |
| * @brief Read Receive Data register. |
| * @rmtoll DR DR LL_I2C_ReceiveData8 |
| * @param I2Cx I2C Instance. |
| * @retval Value between Min_Data=0x0 and Max_Data=0xFF |
| */ |
| __STATIC_INLINE uint8_t LL_I2C_ReceiveData8(I2C_TypeDef *I2Cx) |
| { |
| return (uint8_t)(READ_BIT(I2Cx->DR, I2C_DR_DR)); |
| } |
| |
| /** |
| * @brief Write in Transmit Data Register . |
| * @rmtoll DR DR LL_I2C_TransmitData8 |
| * @param I2Cx I2C Instance. |
| * @param Data Value between Min_Data=0x0 and Max_Data=0xFF |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_I2C_TransmitData8(I2C_TypeDef *I2Cx, uint8_t Data) |
| { |
| MODIFY_REG(I2Cx->DR, I2C_DR_DR, Data); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| #if defined(USE_FULL_LL_DRIVER) |
| /** @defgroup I2C_LL_EF_Init Initialization and de-initialization functions |
| * @{ |
| */ |
| |
| uint32_t LL_I2C_Init(I2C_TypeDef *I2Cx, LL_I2C_InitTypeDef *I2C_InitStruct); |
| uint32_t LL_I2C_DeInit(I2C_TypeDef *I2Cx); |
| void LL_I2C_StructInit(LL_I2C_InitTypeDef *I2C_InitStruct); |
| |
| |
| /** |
| * @} |
| */ |
| #endif /* USE_FULL_LL_DRIVER */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* I2C1 || I2C2 || I2C3 */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* __STM32F2xx_LL_I2C_H */ |
| |
