| /** |
| ****************************************************************************** |
| * @file stm32f2xx_hal.c |
| * @author MCD Application Team |
| * @brief HAL module driver. |
| * This is the common part of the HAL initialization |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use this driver ##### |
| ============================================================================== |
| [..] |
| The common HAL driver contains a set of generic and common APIs that can be |
| used by the PPP peripheral drivers and the user to start using the HAL. |
| [..] |
| The HAL contains two APIs' categories: |
| (+) Common HAL APIs |
| (+) Services HAL APIs |
| |
| @endverbatim |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2016 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f2xx_hal.h" |
| |
| /** @addtogroup STM32F2xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup HAL HAL |
| * @brief HAL module driver. |
| * @{ |
| */ |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /** @addtogroup HAL_Private_Constants |
| * @{ |
| */ |
| /** |
| * @brief STM32F2xx HAL Driver version number V1.2.7 |
| */ |
| #define __STM32F2xx_HAL_VERSION_MAIN 0x01U /*!< [31:24] main version */ |
| #define __STM32F2xx_HAL_VERSION_SUB1 0x02U /*!< [23:16] sub1 version */ |
| #define __STM32F2xx_HAL_VERSION_SUB2 0x07U /*!< [15:8] sub2 version */ |
| #define __STM32F2xx_HAL_VERSION_RC 0x00U /*!< [7:0] release candidate */ |
| #define __STM32F2xx_HAL_VERSION ((__STM32F2xx_HAL_VERSION_MAIN << 24U)\ |
| |(__STM32F2xx_HAL_VERSION_SUB1 << 16U)\ |
| |(__STM32F2xx_HAL_VERSION_SUB2 << 8U) \ |
| |(__STM32F2xx_HAL_VERSION_RC)) |
| |
| #define IDCODE_DEVID_MASK 0x00000FFFU |
| |
| /* ------------ RCC registers bit address in the alias region ----------- */ |
| #define SYSCFG_OFFSET (SYSCFG_BASE - PERIPH_BASE) |
| /* --- MEMRMP Register ---*/ |
| /* Alias word address of UFB_MODE bit */ |
| #define MEMRMP_OFFSET SYSCFG_OFFSET |
| #define UFB_MODE_BIT_NUMBER POSITION_VAL(SYSCFG_MEMRMP_UFB_MODE) |
| #define UFB_MODE_BB (uint32_t)(PERIPH_BB_BASE + (MEMRMP_OFFSET * 32U) + (UFB_MODE_BIT_NUMBER * 4U)) |
| |
| /* --- CMPCR Register ---*/ |
| /* Alias word address of CMP_PD bit */ |
| #define CMPCR_OFFSET (SYSCFG_OFFSET + 0x20U) |
| #define CMP_PD_BIT_NUMBER POSITION_VAL(SYSCFG_CMPCR_CMP_PD) |
| #define CMPCR_CMP_PD_BB (uint32_t)(PERIPH_BB_BASE + (CMPCR_OFFSET * 32U) + (CMP_PD_BIT_NUMBER * 4U)) |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| /* Exported variables ---------------------------------------------------------*/ |
| /** @addtogroup HAL_Exported_Variables |
| * @{ |
| */ |
| __IO uint32_t uwTick; |
| uint32_t uwTickPrio = (1UL << __NVIC_PRIO_BITS); /* Invalid PRIO */ |
| HAL_TickFreqTypeDef uwTickFreq = HAL_TICK_FREQ_DEFAULT; /* 1KHz */ |
| /** |
| * @} |
| */ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Private functions ---------------------------------------------------------*/ |
| |
| /** @defgroup HAL_Exported_Functions HAL Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup HAL_Exported_Functions_Group1 Initialization and de-initialization Functions |
| * @brief Initialization and de-initialization functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Initialization and de-initialization functions ##### |
| =============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Initializes the Flash interface the NVIC allocation and initial clock |
| configuration. It initializes the systick also when timeout is needed |
| and the backup domain when enabled. |
| (+) de-Initializes common part of the HAL |
| (+) Configure The time base source to have 1ms time base with a dedicated |
| Tick interrupt priority. |
| (++) Systick timer is used by default as source of time base, but user |
| can eventually implement his proper time base source (a general purpose |
| timer for example or other time source), keeping in mind that Time base |
| duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and |
| handled in milliseconds basis. |
| (++) Time base configuration function (HAL_InitTick ()) is called automatically |
| at the beginning of the program after reset by HAL_Init() or at any time |
| when clock is configured, by HAL_RCC_ClockConfig(). |
| (++) Source of time base is configured to generate interrupts at regular |
| time intervals. Care must be taken if HAL_Delay() is called from a |
| peripheral ISR process, the Tick interrupt line must have higher priority |
| (numerically lower) than the peripheral interrupt. Otherwise the caller |
| ISR process will be blocked. |
| (++) functions affecting time base configurations are declared as __weak |
| to make override possible in case of other implementations in user file. |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief This function is used to initialize the HAL Library; it must be the first |
| * instruction to be executed in the main program (before to call any other |
| * HAL function), it performs the following: |
| * Configure the Flash prefetch, instruction and Data caches. |
| * Configures the SysTick to generate an interrupt each 1 millisecond, |
| * which is clocked by the HSI (at this stage, the clock is not yet |
| * configured and thus the system is running from the internal HSI at 16 MHz). |
| * Set NVIC Group Priority to 4. |
| * Calls the HAL_MspInit() callback function defined in user file |
| * "stm32f2xx_hal_msp.c" to do the global low level hardware initialization |
| * |
| * @note SysTick is used as time base for the HAL_Delay() function, the application |
| * need to ensure that the SysTick time base is always set to 1 millisecond |
| * to have correct HAL operation. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_Init(void) |
| { |
| /* Configure Flash prefetch, Instruction cache, Data cache */ |
| #if (INSTRUCTION_CACHE_ENABLE != 0U) |
| __HAL_FLASH_INSTRUCTION_CACHE_ENABLE(); |
| #endif /* INSTRUCTION_CACHE_ENABLE */ |
| |
| #if (DATA_CACHE_ENABLE != 0U) |
| __HAL_FLASH_DATA_CACHE_ENABLE(); |
| #endif /* DATA_CACHE_ENABLE */ |
| |
| #if (PREFETCH_ENABLE != 0U) |
| __HAL_FLASH_PREFETCH_BUFFER_ENABLE(); |
| #endif /* PREFETCH_ENABLE */ |
| |
| /* Set Interrupt Group Priority */ |
| HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4); |
| |
| /* Use systick as time base source and configure 1ms tick (default clock after Reset is HSI) */ |
| HAL_InitTick(TICK_INT_PRIORITY); |
| |
| /* Init the low level hardware */ |
| HAL_MspInit(); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief This function de-Initializes common part of the HAL and stops the systick. |
| * This function is optional. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_DeInit(void) |
| { |
| /* Reset of all peripherals */ |
| __HAL_RCC_APB1_FORCE_RESET(); |
| __HAL_RCC_APB1_RELEASE_RESET(); |
| |
| __HAL_RCC_APB2_FORCE_RESET(); |
| __HAL_RCC_APB2_RELEASE_RESET(); |
| |
| __HAL_RCC_AHB1_FORCE_RESET(); |
| __HAL_RCC_AHB1_RELEASE_RESET(); |
| |
| __HAL_RCC_AHB2_FORCE_RESET(); |
| __HAL_RCC_AHB2_RELEASE_RESET(); |
| |
| __HAL_RCC_AHB3_FORCE_RESET(); |
| __HAL_RCC_AHB3_RELEASE_RESET(); |
| |
| /* De-Init the low level hardware */ |
| HAL_MspDeInit(); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the MSP. |
| * @retval None |
| */ |
| __weak void HAL_MspInit(void) |
| { |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_MspInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief DeInitializes the MSP. |
| * @retval None |
| */ |
| __weak void HAL_MspDeInit(void) |
| { |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_MspDeInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief This function configures the source of the time base. |
| * The time source is configured to have 1ms time base with a dedicated |
| * Tick interrupt priority. |
| * @note This function is called automatically at the beginning of program after |
| * reset by HAL_Init() or at any time when clock is reconfigured by HAL_RCC_ClockConfig(). |
| * @note In the default implementation, SysTick timer is the source of time base. |
| * It is used to generate interrupts at regular time intervals. |
| * Care must be taken if HAL_Delay() is called from a peripheral ISR process, |
| * The the SysTick interrupt must have higher priority (numerically lower) |
| * than the peripheral interrupt. Otherwise the caller ISR process will be blocked. |
| * The function is declared as __weak to be overwritten in case of other |
| * implementation in user file. |
| * @param TickPriority Tick interrupt priority. |
| * @retval HAL status |
| */ |
| __weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority) |
| { |
| /* Configure the SysTick to have interrupt in 1ms time basis*/ |
| if (HAL_SYSTICK_Config(SystemCoreClock / (1000U / uwTickFreq)) > 0U) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Configure the SysTick IRQ priority */ |
| if (TickPriority < (1UL << __NVIC_PRIO_BITS)) |
| { |
| HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U); |
| uwTickPrio = TickPriority; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup HAL_Exported_Functions_Group2 HAL Control functions |
| * @brief HAL Control functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### HAL Control functions ##### |
| =============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Provide a tick value in millisecond |
| (+) Provide a blocking delay in millisecond |
| (+) Suspend the time base source interrupt |
| (+) Resume the time base source interrupt |
| (+) Get the HAL API driver version |
| (+) Get the device identifier |
| (+) Get the device revision identifier |
| (+) Enable/Disable Debug module during SLEEP mode |
| (+) Enable/Disable Debug module during STOP mode |
| (+) Enable/Disable Debug module during STANDBY mode |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief This function is called to increment a global variable "uwTick" |
| * used as application time base. |
| * @note In the default implementation, this variable is incremented each 1ms |
| * in Systick ISR. |
| * @note This function is declared as __weak to be overwritten in case of other |
| * implementations in user file. |
| * @retval None |
| */ |
| __weak void HAL_IncTick(void) |
| { |
| uwTick += uwTickFreq; |
| } |
| |
| /** |
| * @brief Provides a tick value in millisecond. |
| * @note This function is declared as __weak to be overwritten in case of other |
| * implementations in user file. |
| * @retval tick value |
| */ |
| __weak uint32_t HAL_GetTick(void) |
| { |
| return uwTick; |
| } |
| |
| /** |
| * @brief This function returns a tick priority. |
| * @retval tick priority |
| */ |
| uint32_t HAL_GetTickPrio(void) |
| { |
| return uwTickPrio; |
| } |
| |
| /** |
| * @brief Set new tick Freq. |
| * @retval status |
| */ |
| HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq) |
| { |
| HAL_StatusTypeDef status = HAL_OK; |
| HAL_TickFreqTypeDef prevTickFreq; |
| |
| assert_param(IS_TICKFREQ(Freq)); |
| |
| if (uwTickFreq != Freq) |
| { |
| /* Back up uwTickFreq frequency */ |
| prevTickFreq = uwTickFreq; |
| |
| /* Update uwTickFreq global variable used by HAL_InitTick() */ |
| uwTickFreq = Freq; |
| |
| /* Apply the new tick Freq */ |
| status = HAL_InitTick(uwTickPrio); |
| |
| if (status != HAL_OK) |
| { |
| /* Restore previous tick frequency */ |
| uwTickFreq = prevTickFreq; |
| } |
| } |
| |
| return status; |
| } |
| |
| /** |
| * @brief return tick frequency. |
| * @retval tick period in Hz |
| */ |
| HAL_TickFreqTypeDef HAL_GetTickFreq(void) |
| { |
| return uwTickFreq; |
| } |
| |
| /** |
| * @brief This function provides minimum delay (in milliseconds) based |
| * on variable incremented. |
| * @note In the default implementation , SysTick timer is the source of time base. |
| * It is used to generate interrupts at regular time intervals where uwTick |
| * is incremented. |
| * @note This function is declared as __weak to be overwritten in case of other |
| * implementations in user file. |
| * @param Delay specifies the delay time length, in milliseconds. |
| * @retval None |
| */ |
| __weak void HAL_Delay(__IO uint32_t Delay) |
| { |
| uint32_t tickstart = HAL_GetTick(); |
| uint32_t wait = Delay; |
| |
| /* Add a freq to guarantee minimum wait */ |
| if (wait < HAL_MAX_DELAY) |
| { |
| wait += (uint32_t)(uwTickFreq); |
| } |
| |
| while ((HAL_GetTick() - tickstart) < wait) |
| { |
| } |
| } |
| |
| /** |
| * @brief Suspend Tick increment. |
| * @note In the default implementation , SysTick timer is the source of time base. It is |
| * used to generate interrupts at regular time intervals. Once HAL_SuspendTick() |
| * is called, the SysTick interrupt will be disabled and so Tick increment |
| * is suspended. |
| * @note This function is declared as __weak to be overwritten in case of other |
| * implementations in user file. |
| * @retval None |
| */ |
| __weak void HAL_SuspendTick(void) |
| { |
| /* Disable SysTick Interrupt */ |
| SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk; |
| } |
| |
| /** |
| * @brief Resume Tick increment. |
| * @note In the default implementation , SysTick timer is the source of time base. It is |
| * used to generate interrupts at regular time intervals. Once HAL_ResumeTick() |
| * is called, the SysTick interrupt will be enabled and so Tick increment |
| * is resumed. |
| * @note This function is declared as __weak to be overwritten in case of other |
| * implementations in user file. |
| * @retval None |
| */ |
| __weak void HAL_ResumeTick(void) |
| { |
| /* Enable SysTick Interrupt */ |
| SysTick->CTRL |= SysTick_CTRL_TICKINT_Msk; |
| } |
| |
| /** |
| * @brief Returns the HAL revision |
| * @retval version : 0xXYZR (8bits for each decimal, R for RC) |
| */ |
| uint32_t HAL_GetHalVersion(void) |
| { |
| return __STM32F2xx_HAL_VERSION; |
| } |
| |
| /** |
| * @brief Returns the device revision identifier. |
| * @retval Device revision identifier |
| */ |
| uint32_t HAL_GetREVID(void) |
| { |
| return((DBGMCU->IDCODE) >> 16U); |
| } |
| |
| /** |
| * @brief Returns the device identifier. |
| * @retval Device identifier |
| */ |
| uint32_t HAL_GetDEVID(void) |
| { |
| return((DBGMCU->IDCODE) & IDCODE_DEVID_MASK); |
| } |
| |
| /** |
| * @brief Enable the Debug Module during SLEEP mode |
| * @retval None |
| */ |
| void HAL_DBGMCU_EnableDBGSleepMode(void) |
| { |
| SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP); |
| } |
| |
| /** |
| * @brief Disable the Debug Module during SLEEP mode |
| * @retval None |
| */ |
| void HAL_DBGMCU_DisableDBGSleepMode(void) |
| { |
| CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP); |
| } |
| |
| /** |
| * @brief Enable the Debug Module during STOP mode |
| * @retval None |
| */ |
| void HAL_DBGMCU_EnableDBGStopMode(void) |
| { |
| SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP); |
| } |
| |
| /** |
| * @brief Disable the Debug Module during STOP mode |
| * @retval None |
| */ |
| void HAL_DBGMCU_DisableDBGStopMode(void) |
| { |
| CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP); |
| } |
| |
| /** |
| * @brief Enable the Debug Module during STANDBY mode |
| * @retval None |
| */ |
| void HAL_DBGMCU_EnableDBGStandbyMode(void) |
| { |
| SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY); |
| } |
| |
| /** |
| * @brief Disable the Debug Module during STANDBY mode |
| * @retval None |
| */ |
| void HAL_DBGMCU_DisableDBGStandbyMode(void) |
| { |
| CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY); |
| } |
| |
| /** |
| * @brief Enables the I/O Compensation Cell. |
| * @note The I/O compensation cell can be used only when the device supply |
| * voltage ranges from 2.4 to 3.6 V. |
| * @retval None |
| */ |
| void HAL_EnableCompensationCell(void) |
| { |
| *(__IO uint32_t *)CMPCR_CMP_PD_BB = (uint32_t)ENABLE; |
| } |
| |
| /** |
| * @brief Power-down the I/O Compensation Cell. |
| * @note The I/O compensation cell can be used only when the device supply |
| * voltage ranges from 2.4 to 3.6 V. |
| * @retval None |
| */ |
| void HAL_DisableCompensationCell(void) |
| { |
| *(__IO uint32_t *)CMPCR_CMP_PD_BB = (uint32_t)DISABLE; |
| } |
| |
| /** |
| * @brief Returns first word of the unique device identifier (UID based on 96 bits) |
| * @retval Device identifier |
| */ |
| uint32_t HAL_GetUIDw0(void) |
| { |
| return (READ_REG(*((uint32_t *)UID_BASE))); |
| } |
| |
| /** |
| * @brief Returns second word of the unique device identifier (UID based on 96 bits) |
| * @retval Device identifier |
| */ |
| uint32_t HAL_GetUIDw1(void) |
| { |
| return (READ_REG(*((uint32_t *)(UID_BASE + 4U)))); |
| } |
| |
| /** |
| * @brief Returns third word of the unique device identifier (UID based on 96 bits) |
| * @retval Device identifier |
| */ |
| uint32_t HAL_GetUIDw2(void) |
| { |
| return (READ_REG(*((uint32_t *)(UID_BASE + 8U)))); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |