blob: 80e1492090e95f921da9423227f786113d96a0a7 [file] [log] [blame]
/**
******************************************************************************
* @file stm32f3xx_hal_adc.c
* @author MCD Application Team
* @brief This file provides firmware functions to manage the following
* functionalities of the Analog to Digital Convertor (ADC)
* peripheral:
* + Initialization and de-initialization functions
* ++ Initialization and Configuration of ADC
* + Operation functions
* ++ Start, stop, get result of conversions of regular
* group, using 3 possible modes: polling, interruption or DMA.
* + Control functions
* ++ Channels configuration on regular group
* ++ Channels configuration on injected group
* ++ Analog Watchdog configuration
* + State functions
* ++ ADC state machine management
* ++ Interrupts and flags management
* Other functions (extended functions) are available in file
* "stm32f3xx_hal_adc_ex.c".
*
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@verbatim
==============================================================================
##### ADC peripheral features #####
==============================================================================
[..]
(+) 12-bit, 10-bit, 8-bit or 6-bit configurable resolution (available only on
STM32F30xxC devices).
(+) Interrupt generation at the end of regular conversion, end of injected
conversion, and in case of analog watchdog or overrun events.
(+) Single and continuous conversion modes.
(+) Scan mode for conversion of several channels sequentially.
(+) Data alignment with in-built data coherency.
(+) Programmable sampling time (channel wise)
(+) ADC conversion of regular group and injected group.
(+) External trigger (timer or EXTI) with configurable polarity
for both regular and injected groups.
(+) DMA request generation for transfer of conversions data of regular group.
(+) Multimode dual mode (available on devices with 2 ADCs or more).
(+) Configurable DMA data storage in Multimode Dual mode (available on devices
with 2 DCs or more).
(+) Configurable delay between conversions in Dual interleaved mode (available
on devices with 2 DCs or more).
(+) ADC calibration
(+) ADC channels selectable single/differential input (available only on
STM32F30xxC devices)
(+) ADC Injected sequencer&channels configuration context queue (available
only on STM32F30xxC devices)
(+) ADC offset on injected and regular groups (offset on regular group
available only on STM32F30xxC devices)
(+) ADC supply requirements: 2.4 V to 3.6 V at full speed and down to 1.8 V at
slower speed.
(+) ADC input range: from Vref- (connected to Vssa) to Vref+ (connected to
Vdda or to an external voltage reference).
##### How to use this driver #####
==============================================================================
[..]
*** Configuration of top level parameters related to ADC ***
============================================================
[..]
(#) Enable the ADC interface
(++) As prerequisite, ADC clock must be configured at RCC top level.
(++) For STM32F30x/STM32F33x devices:
Two possible clock sources: synchronous clock derived from AHB clock
or asynchronous clock derived from ADC dedicated PLL 72MHz.
- Synchronous clock is mandatory since used as ADC core clock.
Synchronous clock can be used optionally as ADC conversion clock, depending on ADC init structure clock setting.
Synchronous clock is configured using macro __ADCx_CLK_ENABLE().
- Asynchronous can be used optionally as ADC conversion clock, depending on ADC init structure clock setting.
Asynchronous clock is configured using function HAL_RCCEx_PeriphCLKConfig().
(+++) For example, in case of device with a single ADC:
Into HAL_ADC_MspInit() (recommended code location) or with
other device clock parameters configuration:
(+++) __HAL_RCC_ADC1_CLK_ENABLE() (mandatory)
(+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC (optional, if ADC conversion from asynchronous clock)
(+++) PeriphClkInit.Adc1ClockSelection = RCC_ADC1PLLCLK_DIV1 (optional, if ADC conversion from asynchronous clock)
(+++) HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInitStructure) (optional, if ADC conversion from asynchronous clock)
(+++) For example, in case of device with 4 ADCs:
(+++) if((hadc->Instance == ADC1) || (hadc->Instance == ADC2))
(+++) {
(+++) __HAL_RCC_ADC12_CLK_ENABLE() (mandatory)
(+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC (optional, if ADC conversion from asynchronous clock)
(+++) PeriphClkInit.Adc12ClockSelection = RCC_ADC12PLLCLK_DIV1 (optional, if ADC conversion from asynchronous clock)
(+++) HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInitStructure) (optional, if ADC conversion from asynchronous clock)
(+++) }
(+++) else
(+++) {
(+++) __HAL_RCC_ADC34_CLK_ENABLE() (mandatory)
(+++) PeriphClkInit.Adc34ClockSelection = RCC_ADC34PLLCLK_DIV1; (optional, if ADC conversion from asynchronous clock)
(+++) HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInitStructure); (optional, if ADC conversion from asynchronous clock)
(+++) }
(++) For STM32F37x devices:
One clock setting is mandatory:
ADC clock (core and conversion clock) from APB2 clock.
(+++) Example:
Into HAL_ADC_MspInit() (recommended code location) or with
other device clock parameters configuration:
(+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC
(+++) PeriphClkInit.AdcClockSelection = RCC_ADCPLLCLK_DIV2
(+++) HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit)
(#) ADC pins configuration
(++) Enable the clock for the ADC GPIOs
using macro __HAL_RCC_GPIOx_CLK_ENABLE()
(++) Configure these ADC pins in analog mode
using function HAL_GPIO_Init()
(#) Optionally, in case of usage of ADC with interruptions:
(++) Configure the NVIC for ADC
using function HAL_NVIC_EnableIRQ(ADCx_IRQn)
(++) Insert the ADC interruption handler function HAL_ADC_IRQHandler()
into the function of corresponding ADC interruption vector
ADCx_IRQHandler().
(#) Optionally, in case of usage of DMA:
(++) Configure the DMA (DMA channel, mode normal or circular, ...)
using function HAL_DMA_Init().
(++) Configure the NVIC for DMA
using function HAL_NVIC_EnableIRQ(DMAx_Channelx_IRQn)
(++) Insert the ADC interruption handler function HAL_ADC_IRQHandler()
into the function of corresponding DMA interruption vector
DMAx_Channelx_IRQHandler().
*** Configuration of ADC, groups regular/injected, channels parameters ***
==========================================================================
[..]
(#) Configure the ADC parameters (resolution, data alignment, ...)
and regular group parameters (conversion trigger, sequencer, ...)
using function HAL_ADC_Init().
(#) Configure the channels for regular group parameters (channel number,
channel rank into sequencer, ..., into regular group)
using function HAL_ADC_ConfigChannel().
(#) Optionally, configure the injected group parameters (conversion trigger,
sequencer, ..., of injected group)
and the channels for injected group parameters (channel number,
channel rank into sequencer, ..., into injected group)
using function HAL_ADCEx_InjectedConfigChannel().
(#) Optionally, configure the analog watchdog parameters (channels
monitored, thresholds, ...)
using function HAL_ADC_AnalogWDGConfig().
(#) Optionally, for devices with several ADC instances: configure the
multimode parameters
using function HAL_ADCEx_MultiModeConfigChannel().
*** Execution of ADC conversions ***
====================================
[..]
(#) Optionally, perform an automatic ADC calibration to improve the
conversion accuracy
using function HAL_ADCEx_Calibration_Start().
(#) ADC driver can be used among three modes: polling, interruption,
transfer by DMA.
(++) ADC conversion by polling:
(+++) Activate the ADC peripheral and start conversions
using function HAL_ADC_Start()
(+++) Wait for ADC conversion completion
using function HAL_ADC_PollForConversion()
(or for injected group: HAL_ADCEx_InjectedPollForConversion() )
(+++) Retrieve conversion results
using function HAL_ADC_GetValue()
(or for injected group: HAL_ADCEx_InjectedGetValue() )
(+++) Stop conversion and disable the ADC peripheral
using function HAL_ADC_Stop()
(++) ADC conversion by interruption:
(+++) Activate the ADC peripheral and start conversions
using function HAL_ADC_Start_IT()
(+++) Wait for ADC conversion completion by call of function
HAL_ADC_ConvCpltCallback()
(this function must be implemented in user program)
(or for injected group: HAL_ADCEx_InjectedConvCpltCallback() )
(+++) Retrieve conversion results
using function HAL_ADC_GetValue()
(or for injected group: HAL_ADCEx_InjectedGetValue() )
(+++) Stop conversion and disable the ADC peripheral
using function HAL_ADC_Stop_IT()
(++) ADC conversion with transfer by DMA:
(+++) Activate the ADC peripheral and start conversions
using function HAL_ADC_Start_DMA()
(+++) Wait for ADC conversion completion by call of function
HAL_ADC_ConvCpltCallback() or HAL_ADC_ConvHalfCpltCallback()
(these functions must be implemented in user program)
(+++) Conversion results are automatically transferred by DMA into
destination variable address.
(+++) Stop conversion and disable the ADC peripheral
using function HAL_ADC_Stop_DMA()
(++) For devices with several ADCs: ADC multimode conversion
with transfer by DMA:
(+++) Activate the ADC peripheral (slave)
using function HAL_ADC_Start()
(conversion start pending ADC master)
(+++) Activate the ADC peripheral (master) and start conversions
using function HAL_ADCEx_MultiModeStart_DMA()
(+++) Wait for ADC conversion completion by call of function
HAL_ADC_ConvCpltCallback() or HAL_ADC_ConvHalfCpltCallback()
(these functions must be implemented in user program)
(+++) Conversion results are automatically transferred by DMA into
destination variable address.
(+++) Stop conversion and disable the ADC peripheral (master)
using function HAL_ADCEx_MultiModeStop_DMA()
(+++) Stop conversion and disable the ADC peripheral (slave)
using function HAL_ADC_Stop_IT()
[..]
(@) Callback functions must be implemented in user program:
(+@) HAL_ADC_ErrorCallback()
(+@) HAL_ADC_LevelOutOfWindowCallback() (callback of analog watchdog)
(+@) HAL_ADC_ConvCpltCallback()
(+@) HAL_ADC_ConvHalfCpltCallback
(+@) HAL_ADCEx_InjectedConvCpltCallback()
(+@) HAL_ADCEx_InjectedQueueOverflowCallback() (for STM32F30x/STM32F33x devices)
*** Deinitialization of ADC ***
============================================================
[..]
(#) Disable the ADC interface
(++) ADC clock can be hard reset and disabled at RCC top level.
(++) Hard reset of ADC peripherals
using macro __ADCx_FORCE_RESET(), __ADCx_RELEASE_RESET().
(++) ADC clock disable
using the equivalent macro/functions as configuration step.
(++) For STM32F30x/STM32F33x devices:
Caution: For devices with several ADCs:
These settings impact both ADC of common group: ADC1&ADC2, ADC3&ADC4
if available (ADC2, ADC3, ADC4 availability depends on STM32 product)
(+++) For example, in case of device with a single ADC:
Into HAL_ADC_MspDeInit() (recommended code location) or with
other device clock parameters configuration:
(+++) __HAL_RCC_ADC1_FORCE_RESET() (optional)
(+++) __HAL_RCC_ADC1_RELEASE_RESET() (optional)
(+++) __HAL_RCC_ADC1_CLK_DISABLE() (mandatory)
(+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC (optional, if configured before)
(+++) PeriphClkInit.Adc1ClockSelection = RCC_ADC1PLLCLK_OFF (optional, if configured before)
(+++) HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInitStructure) (optional, if configured before)
(+++) For example, in case of device with 4 ADCs:
(+++) if((hadc->Instance == ADC1) || (hadc->Instance == ADC2))
(+++) {
(+++) __HAL_RCC_ADC12_FORCE_RESET() (optional)
(+++) __HAL_RCC_ADC12_RELEASE_RESET() (optional)
(+++) __HAL_RCC_ADC12_CLK_DISABLE() (mandatory)
(+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC (optional, if configured before)
(+++) PeriphClkInit.Adc12ClockSelection = RCC_ADC12PLLCLK_OFF (optional, if configured before)
(+++) HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInitStructure) (optional, if configured before)
(+++) }
(+++) else
(+++) {
(+++) __HAL_RCC_ADC32_FORCE_RESET() (optional)
(+++) __HAL_RCC_ADC32_RELEASE_RESET() (optional)
(+++) __HAL_RCC_ADC34_CLK_DISABLE() (mandatory)
(+++) PeriphClkInit.Adc34ClockSelection = RCC_ADC34PLLCLK_OFF (optional, if configured before)
(+++) HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInitStructure) (optional, if configured before)
(+++) }
(++) For STM32F37x devices:
(+++) Example:
Into HAL_ADC_MspDeInit() (recommended code location) or with
other device clock parameters configuration:
(+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC
(+++) PeriphClkInit.AdcClockSelection = RCC_ADCPLLCLK_OFF
(+++) HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit)
(#) ADC pins configuration
(++) Disable the clock for the ADC GPIOs
using macro __HAL_RCC_GPIOx_CLK_DISABLE()
(#) Optionally, in case of usage of ADC with interruptions:
(++) Disable the NVIC for ADC
using function HAL_NVIC_DisableIRQ(ADCx_IRQn)
(#) Optionally, in case of usage of DMA:
(++) Deinitialize the DMA
using function HAL_DMA_DeInit().
(++) Disable the NVIC for DMA
using function HAL_NVIC_DisableIRQ(DMAx_Channelx_IRQn)
[..]
*** Callback registration ***
=============================================
[..]
The compilation flag USE_HAL_ADC_REGISTER_CALLBACKS, when set to 1,
allows the user to configure dynamically the driver callbacks.
Use Functions HAL_ADC_RegisterCallback()
to register an interrupt callback.
[..]
Function HAL_ADC_RegisterCallback() allows to register following callbacks:
(+) ConvCpltCallback : ADC conversion complete callback
(+) ConvHalfCpltCallback : ADC conversion DMA half-transfer callback
(+) LevelOutOfWindowCallback : ADC analog watchdog 1 callback
(+) ErrorCallback : ADC error callback
(+) InjectedConvCpltCallback : ADC group injected conversion complete callback
(+) MspInitCallback : ADC Msp Init callback
(+) MspDeInitCallback : ADC Msp DeInit callback
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
[..]
Use function HAL_ADC_UnRegisterCallback to reset a callback to the default
weak function.
[..]
HAL_ADC_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) ConvCpltCallback : ADC conversion complete callback
(+) ConvHalfCpltCallback : ADC conversion DMA half-transfer callback
(+) LevelOutOfWindowCallback : ADC analog watchdog 1 callback
(+) ErrorCallback : ADC error callback
(+) InjectedConvCpltCallback : ADC group injected conversion complete callback
(+) MspInitCallback : ADC Msp Init callback
(+) MspDeInitCallback : ADC Msp DeInit callback
[..]
By default, after the HAL_ADC_Init() and when the state is HAL_ADC_STATE_RESET
all callbacks are set to the corresponding weak functions:
examples HAL_ADC_ConvCpltCallback(), HAL_ADC_ErrorCallback().
Exception done for MspInit and MspDeInit functions that are
reset to the legacy weak functions in the HAL_ADC_Init()/ HAL_ADC_DeInit() only when
these callbacks are null (not registered beforehand).
[..]
If MspInit or MspDeInit are not null, the HAL_ADC_Init()/ HAL_ADC_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
[..]
Callbacks can be registered/unregistered in HAL_ADC_STATE_READY state only.
Exception done MspInit/MspDeInit functions that can be registered/unregistered
in HAL_ADC_STATE_READY or HAL_ADC_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
[..]
Then, the user first registers the MspInit/MspDeInit user callbacks
using HAL_ADC_RegisterCallback() before calling HAL_ADC_DeInit()
or HAL_ADC_Init() function.
[..]
When the compilation flag USE_HAL_ADC_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available and all callbacks
are set to the corresponding weak functions.
@endverbatim
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f3xx_hal.h"
/** @addtogroup STM32F3xx_HAL_Driver
* @{
*/
/** @defgroup ADC ADC
* @brief ADC HAL module driver
* @{
*/
#ifdef HAL_ADC_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup ADC_Exported_Functions ADC Exported Functions
* @{
*/
/** @defgroup ADC_Exported_Functions_Group1 Initialization and de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
===============================================================================
##### Initialization and de-initialization functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Initialize and configure the ADC.
(+) De-initialize the ADC.
@endverbatim
* @{
*/
/**
* @brief Initializes the ADC peripheral and regular group according to
* parameters specified in structure "ADC_InitTypeDef".
* @note As prerequisite, ADC clock must be configured at RCC top level
* depending on both possible clock sources: PLL clock or AHB clock.
* See commented example code below that can be copied and uncommented
* into HAL_ADC_MspInit().
* @note Possibility to update parameters on the fly:
* This function initializes the ADC MSP (HAL_ADC_MspInit()) only when
* coming from ADC state reset. Following calls to this function can
* be used to reconfigure some parameters of ADC_InitTypeDef
* structure on the fly, without modifying MSP configuration. If ADC
* MSP has to be modified again, HAL_ADC_DeInit() must be called
* before HAL_ADC_Init().
* The setting of these parameters is conditioned to ADC state.
* For parameters constraints, see comments of structure
* "ADC_InitTypeDef".
* @note This function configures the ADC within 2 scopes: scope of entire
* ADC and scope of regular group. For parameters details, see comments
* of structure "ADC_InitTypeDef".
* @note For devices with several ADCs: parameters related to common ADC
* registers (ADC clock mode) are set only if all ADCs sharing the
* same common group are disabled.
* If this is not the case, these common parameters setting are
* bypassed without error reporting: it can be the intended behaviour in
* case of update of a parameter of ADC_InitTypeDef on the fly,
* without disabling the other ADCs sharing the same common group.
* @param hadc ADC handle
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_Init(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Deinitialize the ADC peripheral registers to their default reset
* values, with deinitialization of the ADC MSP.
* @note For devices with several ADCs: reset of ADC common registers is done
* only if all ADCs sharing the same common group are disabled.
* If this is not the case, reset of these common parameters reset is
* bypassed without error reporting: it can be the intended behaviour in
* case of reset of a single ADC while the other ADCs sharing the same
* common group is still running.
* @note For devices with several ADCs: Global reset of all ADCs sharing a
* common group is possible.
* As this function is intended to reset a single ADC, to not impact
* other ADCs, instructions for global reset of multiple ADCs have been
* let commented below.
* If needed, the example code can be copied and uncommented into
* function HAL_ADC_MspDeInit().
* @param hadc ADC handle
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_DeInit(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Initializes the ADC MSP.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_MspInit must be implemented in the user file.
*/
}
/**
* @brief DeInitializes the ADC MSP.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_MspDeInit must be implemented in the user file.
*/
}
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
/**
* @brief Register a User ADC Callback
* To be used instead of the weak predefined callback
* @param hadc Pointer to a ADC_HandleTypeDef structure that contains
* the configuration information for the specified ADC.
* @param CallbackID ID of the callback to be registered
* This parameter can be one of the following values:
* @arg @ref HAL_ADC_CONVERSION_COMPLETE_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_CONVERSION_HALF_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID ADC analog watchdog 1 callback ID
* @arg @ref HAL_ADC_ERROR_CB_ID ADC error callback ID
* @arg @ref HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID ADC group injected conversion complete callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID ADC Msp Init callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID ADC Msp DeInit callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID MspInit callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID MspDeInit callback ID
* @param pCallback pointer to the Callback function
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_RegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID, pADC_CallbackTypeDef pCallback)
{
HAL_StatusTypeDef status = HAL_OK;
if (pCallback == NULL)
{
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
return HAL_ERROR;
}
if ((hadc->State & HAL_ADC_STATE_READY) != 0)
{
switch (CallbackID)
{
case HAL_ADC_CONVERSION_COMPLETE_CB_ID :
hadc->ConvCpltCallback = pCallback;
break;
case HAL_ADC_CONVERSION_HALF_CB_ID :
hadc->ConvHalfCpltCallback = pCallback;
break;
case HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID :
hadc->LevelOutOfWindowCallback = pCallback;
break;
case HAL_ADC_ERROR_CB_ID :
hadc->ErrorCallback = pCallback;
break;
case HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID :
hadc->InjectedConvCpltCallback = pCallback;
break;
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = pCallback;
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = pCallback;
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else if (HAL_ADC_STATE_RESET == hadc->State)
{
switch (CallbackID)
{
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = pCallback;
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = pCallback;
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else
{
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
}
return status;
}
/**
* @brief Unregister a ADC Callback
* ADC callback is redirected to the weak predefined callback
* @param hadc Pointer to a ADC_HandleTypeDef structure that contains
* the configuration information for the specified ADC.
* @param CallbackID ID of the callback to be unregistered
* This parameter can be one of the following values:
* @arg @ref HAL_ADC_CONVERSION_COMPLETE_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_CONVERSION_HALF_CB_ID ADC conversion complete callback ID
* @arg @ref HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID ADC analog watchdog 1 callback ID
* @arg @ref HAL_ADC_ERROR_CB_ID ADC error callback ID
* @arg @ref HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID ADC group injected conversion complete callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID ADC Msp Init callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID ADC Msp DeInit callback ID
* @arg @ref HAL_ADC_MSPINIT_CB_ID MspInit callback ID
* @arg @ref HAL_ADC_MSPDEINIT_CB_ID MspDeInit callback ID
* @retval HAL status
*/
HAL_StatusTypeDef HAL_ADC_UnRegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID)
{
HAL_StatusTypeDef status = HAL_OK;
if ((hadc->State & HAL_ADC_STATE_READY) != 0)
{
switch (CallbackID)
{
case HAL_ADC_CONVERSION_COMPLETE_CB_ID :
hadc->ConvCpltCallback = HAL_ADC_ConvCpltCallback;
break;
case HAL_ADC_CONVERSION_HALF_CB_ID :
hadc->ConvHalfCpltCallback = HAL_ADC_ConvHalfCpltCallback;
break;
case HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID :
hadc->LevelOutOfWindowCallback = HAL_ADC_LevelOutOfWindowCallback;
break;
case HAL_ADC_ERROR_CB_ID :
hadc->ErrorCallback = HAL_ADC_ErrorCallback;
break;
case HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID :
hadc->InjectedConvCpltCallback = HAL_ADCEx_InjectedConvCpltCallback;
break;
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = HAL_ADC_MspInit; /* Legacy weak MspInit */
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = HAL_ADC_MspDeInit; /* Legacy weak MspDeInit */
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else if (HAL_ADC_STATE_RESET == hadc->State)
{
switch (CallbackID)
{
case HAL_ADC_MSPINIT_CB_ID :
hadc->MspInitCallback = HAL_ADC_MspInit; /* Legacy weak MspInit */
break;
case HAL_ADC_MSPDEINIT_CB_ID :
hadc->MspDeInitCallback = HAL_ADC_MspDeInit; /* Legacy weak MspDeInit */
break;
default :
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
break;
}
}
else
{
/* Update the error code */
hadc->ErrorCode |= HAL_ADC_ERROR_INVALID_CALLBACK;
/* Return error status */
status = HAL_ERROR;
}
return status;
}
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/**
* @}
*/
/** @defgroup ADC_Exported_Functions_Group2 Input and Output operation functions
* @brief IO operation functions
*
@verbatim
===============================================================================
##### IO operation functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Start conversion of regular group.
(+) Stop conversion of regular group.
(+) Poll for conversion complete on regular group.
(+) Poll for conversion event.
(+) Get result of regular channel conversion.
(+) Start conversion of regular group and enable interruptions.
(+) Stop conversion of regular group and disable interruptions.
(+) Handle ADC interrupt request
(+) Start conversion of regular group and enable DMA transfer.
(+) Stop conversion of regular group and disable ADC DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Enables ADC, starts conversion of regular group.
* Interruptions enabled in this function: None.
* @note: Case of multimode enabled (for devices with several ADCs): This
* function must be called for ADC slave first, then ADC master.
* For ADC slave, ADC is enabled only (conversion is not started).
* For ADC master, ADC is enabled and multimode conversion is started.
* @param hadc ADC handle
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_Start(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Stop ADC conversion of regular group (and injected group in
* case of auto_injection mode), disable ADC peripheral.
* @note: ADC peripheral disable is forcing stop of potential
* conversion on injected group. If injected group is under use, it
* should be preliminarily stopped using HAL_ADCEx_InjectedStop function.
* @note: Case of multimode enabled (for devices with several ADCs): This
* function must be called for ADC master first, then ADC slave.
* For ADC master, converson is stopped and ADC is disabled.
* For ADC slave, ADC is disabled only (conversion stop of ADC master
* has already stopped conversion of ADC slave).
* @param hadc ADC handle
* @retval HAL status.
*/
__weak HAL_StatusTypeDef HAL_ADC_Stop(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Wait for regular group conversion to be completed.
* @param hadc ADC handle
* @param Timeout Timeout value in millisecond.
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
UNUSED(Timeout);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Poll for conversion event.
* @param hadc ADC handle
* @param EventType the ADC event type.
* This parameter can be one of the following values:
* @arg ADC_AWD_EVENT: ADC Analog watchdog 1 event (main analog watchdog, present on all STM32 devices)
* @arg ADC_AWD2_EVENT: ADC Analog watchdog 2 event (additional analog watchdog, present only on STM32F3 devices)
* @arg ADC_AWD3_EVENT: ADC Analog watchdog 3 event (additional analog watchdog, present only on STM32F3 devices)
* @arg ADC_OVR_EVENT: ADC Overrun event
* @arg ADC_JQOVF_EVENT: ADC Injected context queue overflow event
* @param Timeout Timeout value in millisecond.
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_PollForEvent(ADC_HandleTypeDef* hadc, uint32_t EventType, uint32_t Timeout)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
UNUSED(EventType);
UNUSED(Timeout);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Enables ADC, starts conversion of regular group with interruption.
* Interruptions enabled in this function:
* - EOC (end of conversion of regular group) or EOS (end of
* sequence of regular group) depending on ADC initialization
* parameter "EOCSelection" (if available)
* - overrun (if available)
* Each of these interruptions has its dedicated callback function.
* @note: Case of multimode enabled (for devices with several ADCs): This
* function must be called for ADC slave first, then ADC master.
* For ADC slave, ADC is enabled only (conversion is not started).
* For ADC master, ADC is enabled and multimode conversion is started.
* @param hadc ADC handle
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Stop ADC conversion of regular group (and injected group in
* case of auto_injection mode), disable interruption of
* end-of-conversion, disable ADC peripheral.
* @note: ADC peripheral disable is forcing stop of potential
* conversion on injected group. If injected group is under use, it
* should be preliminarily stopped using HAL_ADCEx_InjectedStop function.
* @note: Case of multimode enabled (for devices with several ADCs): This
* function must be called for ADC master first, then ADC slave.
* For ADC master, conversion is stopped and ADC is disabled.
* For ADC slave, ADC is disabled only (conversion stop of ADC master
* has already stopped conversion of ADC slave).
* @param hadc ADC handle
* @retval HAL status.
*/
__weak HAL_StatusTypeDef HAL_ADC_Stop_IT(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Enables ADC, starts conversion of regular group and transfers result
* through DMA.
* Interruptions enabled in this function:
* - DMA transfer complete
* - DMA half transfer
* - overrun (if available)
* Each of these interruptions has its dedicated callback function.
* @note: Case of multimode enabled (for devices with several ADCs): This
* function is for single-ADC mode only. For multimode, use the
* dedicated MultimodeStart function.
* @param hadc ADC handle
* @param pData The destination Buffer address.
* @param Length The length of data to be transferred from ADC peripheral to memory.
* @retval None
*/
__weak HAL_StatusTypeDef HAL_ADC_Start_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
UNUSED(pData);
UNUSED(Length);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Stop ADC conversion of regular group (and injected group in
* case of auto_injection mode), disable ADC DMA transfer, disable
* ADC peripheral.
* @note: ADC peripheral disable is forcing stop of potential
* conversion on injected group. If injected group is under use, it
* should be preliminarily stopped using HAL_ADCEx_InjectedStop function.
* @note: Case of multimode enabled (for devices with several ADCs): This
* function is for single-ADC mode only. For multimode, use the
* dedicated MultimodeStop function.
* @param hadc ADC handle
* @retval HAL status.
*/
__weak HAL_StatusTypeDef HAL_ADC_Stop_DMA(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Get ADC regular group conversion result.
* @note Reading DR register automatically clears EOC (end of conversion of
* regular group) flag.
* Additionally, this functions clears EOS (end of sequence of
* regular group) flag, in case of the end of the sequence is reached.
* @param hadc ADC handle
* @retval Converted value
*/
__weak uint32_t HAL_ADC_GetValue(ADC_HandleTypeDef* hadc)
{
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return ADC converted value */
return hadc->Instance->DR;
}
/**
* @brief Handles ADC interrupt request.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_IRQHandler(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
}
/**
* @brief Conversion complete callback in non blocking mode
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_ConvCpltCallback must be implemented in the user file.
*/
}
/**
* @brief Conversion DMA half-transfer callback in non blocking mode
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_ConvHalfCpltCallback(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_ConvHalfCpltCallback must be implemented in the user file.
*/
}
/**
* @brief Analog watchdog callback in non blocking mode.
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_LevelOutOfWindowCallback(ADC_HandleTypeDef* hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_LevelOoutOfWindowCallback must be implemented in the user file.
*/
}
/**
* @brief ADC error callback in non blocking mode
* (ADC conversion with interruption or transfer by DMA)
* @param hadc ADC handle
* @retval None
*/
__weak void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
/* NOTE : This function should not be modified. When the callback is needed,
function HAL_ADC_ErrorCallback must be implemented in the user file.
*/
}
/**
* @}
*/
/** @defgroup ADC_Exported_Functions_Group3 Peripheral Control functions
* @brief Peripheral Control functions
*
@verbatim
===============================================================================
##### Peripheral Control functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Configure channels on regular group
(+) Configure the analog watchdog
@endverbatim
* @{
*/
/**
* @brief Configures the the selected channel to be linked to the regular
* group.
* @note In case of usage of internal measurement channels:
* Vbat/VrefInt/TempSensor.
* The recommended sampling time is at least:
* - For devices STM32F37x: 17.1us for temperature sensor
* - For the other STM32F3 devices: 2.2us for each of channels
* Vbat/VrefInt/TempSensor.
* These internal paths can be be disabled using function
* HAL_ADC_DeInit().
* @note Possibility to update parameters on the fly:
* This function initializes channel into regular group, following
* calls to this function can be used to reconfigure some parameters
* of structure "ADC_ChannelConfTypeDef" on the fly, without reseting
* the ADC.
* The setting of these parameters is conditioned to ADC state.
* For parameters constraints, see comments of structure
* "ADC_ChannelConfTypeDef".
* @param hadc ADC handle
* @param sConfig Structure of ADC channel for regular group.
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef* hadc, ADC_ChannelConfTypeDef* sConfig)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
UNUSED(sConfig);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @brief Configures the analog watchdog.
* @note Possibility to update parameters on the fly:
* This function initializes the selected analog watchdog, following
* calls to this function can be used to reconfigure some parameters
* of structure "ADC_AnalogWDGConfTypeDef" on the fly, without reseting
* the ADC.
* The setting of these parameters is conditioned to ADC state.
* For parameters constraints, see comments of structure
* "ADC_AnalogWDGConfTypeDef".
* @param hadc ADC handle
* @param AnalogWDGConfig Structure of ADC analog watchdog configuration
* @retval HAL status
*/
__weak HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef* hadc, ADC_AnalogWDGConfTypeDef* AnalogWDGConfig)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hadc);
UNUSED(AnalogWDGConfig);
/* Note : This function is defined into this file for library reference. */
/* Function content is located into file stm32f3xx_hal_adc_ex.c */
/* Return function status */
return HAL_ERROR;
}
/**
* @}
*/
/** @defgroup ADC_Exported_Functions_Group4 Peripheral State functions
* @brief ADC Peripheral State functions
*
@verbatim
===============================================================================
##### Peripheral state and errors functions #####
===============================================================================
[..]
This subsection provides functions to get in run-time the status of the
peripheral.
(+) Check the ADC state
(+) Check the ADC error code
@endverbatim
* @{
*/
/**
* @brief return the ADC state
* @note ADC state machine is managed by bitfield, state must be compared
* with bit by bit.
* For example:
* " if (HAL_IS_BIT_SET(HAL_ADC_GetState(hadc1), HAL_ADC_STATE_REG_BUSY)) "
* " if (HAL_IS_BIT_SET(HAL_ADC_GetState(hadc1), HAL_ADC_STATE_AWD1) ) "
* @param hadc ADC handle
* @retval HAL state
*/
uint32_t HAL_ADC_GetState(ADC_HandleTypeDef* hadc)
{
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
/* Return ADC state */
return hadc->State;
}
/**
* @brief Return the ADC error code
* @param hadc ADC handle
* @retval ADC Error Code
*/
uint32_t HAL_ADC_GetError(ADC_HandleTypeDef *hadc)
{
return hadc->ErrorCode;
}
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_ADC_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/