| /** |
| ****************************************************************************** |
| * @file stm32f3xx_ll_fmc.c |
| * @author MCD Application Team |
| * @brief FMC Low Layer HAL module driver. |
| * |
| * This file provides firmware functions to manage the following |
| * functionalities of the Flexible Memory Controller (FMC) peripheral memories: |
| * + Initialization/de-initialization functions |
| * + Peripheral Control functions |
| * + Peripheral State functions |
| * |
| @verbatim |
| ============================================================================= |
| ##### FMC peripheral features ##### |
| ============================================================================= |
| [..] The Flexible memory controller (FMC) includes following memory controllers: |
| (+) The NOR/PSRAM memory controller |
| (+) The PC Card memory controller |
| (+) The NAND memory controller |
| |
| [..] The FMC functional block makes the interface with synchronous and asynchronous static |
| memories and 16-bit PC memory cards. Its main purposes are: |
| (+) to translate AHB transactions into the appropriate external device protocol. |
| (+) to meet the access time requirements of the external memory devices. |
| |
| [..] All external memories share the addresses, data and control signals with the controller. |
| Each external device is accessed by means of a unique Chip Select. The FMC performs |
| only one access at a time to an external device. |
| The main features of the FMC controller are the following: |
| (+) Interface with static-memory mapped devices including: |
| (++) Static random access memory (SRAM). |
| (++) NOR Flash memory. |
| (++) PSRAM (4 memory banks). |
| (++) 16-bit PC Card compatible devices |
| (++) Two banks of NAND Flash memory with ECC hardware to check up to 8 Kbytes of |
| data |
| (+) Independent Chip Select control for each memory bank |
| (+) Independent configuration for each memory bank |
| |
| @endverbatim |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> |
| * |
| * Redistribution and use in source and binary forms, with or without modification, |
| * are permitted provided that the following conditions are met: |
| * 1. Redistributions of source code must retain the above copyright notice, |
| * this list of conditions and the following disclaimer. |
| * 2. Redistributions in binary form must reproduce the above copyright notice, |
| * this list of conditions and the following disclaimer in the documentation |
| * and/or other materials provided with the distribution. |
| * 3. Neither the name of STMicroelectronics nor the names of its contributors |
| * may be used to endorse or promote products derived from this software |
| * without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
| * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
| * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE |
| * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR |
| * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER |
| * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, |
| * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f3xx_hal.h" |
| |
| /** @addtogroup STM32F3xx_HAL_Driver |
| * @{ |
| */ |
| |
| #if defined(FMC_BANK1) |
| |
| #if defined(HAL_SRAM_MODULE_ENABLED) || defined(HAL_NOR_MODULE_ENABLED) || defined(HAL_PCCARD_MODULE_ENABLED) || defined(HAL_NAND_MODULE_ENABLED) |
| |
| /** @defgroup FMC_LL FMC Low Layer |
| * @brief FMC driver modules |
| * @{ |
| */ |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /** @defgroup FMC_LL_Private_Constants FMC Low Layer Private Constants |
| * @{ |
| */ |
| |
| /* ----------------------- FMC registers bit mask --------------------------- */ |
| /* --- PCR Register ---*/ |
| /* PCR register clear mask */ |
| #define PCR_CLEAR_MASK ((uint32_t)(FMC_PCRx_PWAITEN | FMC_PCRx_PBKEN | \ |
| FMC_PCRx_PTYP | FMC_PCRx_PWID | \ |
| FMC_PCRx_ECCEN | FMC_PCRx_TCLR | \ |
| FMC_PCRx_TAR | FMC_PCRx_ECCPS)) |
| |
| /* --- PMEM Register ---*/ |
| /* PMEM register clear mask */ |
| #define PMEM_CLEAR_MASK ((uint32_t)(FMC_PMEMx_MEMSETx | FMC_PMEMx_MEMWAITx |\ |
| FMC_PMEMx_MEMHOLDx | FMC_PMEMx_MEMHIZx)) |
| |
| /* --- PATT Register ---*/ |
| /* PATT register clear mask */ |
| #define PATT_CLEAR_MASK ((uint32_t)(FMC_PATTx_ATTSETx | FMC_PATTx_ATTWAITx |\ |
| FMC_PATTx_ATTHOLDx | FMC_PATTx_ATTHIZx)) |
| |
| /* --- BCR Register ---*/ |
| /* BCR register clear mask */ |
| #define BCR_CLEAR_MASK ((uint32_t)(FMC_BCRx_MBKEN | FMC_BCRx_MUXEN |\ |
| FMC_BCRx_MTYP | FMC_BCRx_MWID |\ |
| FMC_BCRx_FACCEN | FMC_BCRx_BURSTEN |\ |
| FMC_BCRx_WAITPOL | FMC_BCRx_WRAPMOD |\ |
| FMC_BCRx_WAITCFG | FMC_BCRx_WREN |\ |
| FMC_BCRx_WAITEN | FMC_BCRx_EXTMOD |\ |
| FMC_BCRx_ASYNCWAIT | FMC_BCRx_CBURSTRW |\ |
| FMC_BCR1_CCLKEN)) |
| |
| /* --- BTR Register ---*/ |
| /* BTR register clear mask */ |
| #define BTR_CLEAR_MASK ((uint32_t)(FMC_BTRx_ADDSET | FMC_BTRx_ADDHLD |\ |
| FMC_BTRx_DATAST | FMC_BTRx_BUSTURN |\ |
| FMC_BTRx_CLKDIV | FMC_BTRx_DATLAT |\ |
| FMC_BTRx_ACCMOD)) |
| |
| /* --- BWTR Register ---*/ |
| /* BWTR register clear mask */ |
| #define BWTR_CLEAR_MASK ((uint32_t)(FMC_BWTRx_ADDSET | FMC_BWTRx_ADDHLD |\ |
| FMC_BWTRx_DATAST | FMC_BWTRx_ACCMOD)) |
| |
| /* --- PIO4 Register ---*/ |
| /* PIO4 register clear mask */ |
| #define PIO4_CLEAR_MASK ((uint32_t)(FMC_PIO4_IOSET4 | FMC_PIO4_IOWAIT4 | \ |
| FMC_PIO4_IOHOLD4 | FMC_PIO4_IOHIZ4)) |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| /** @defgroup FMC_LL_Private_Macros FMC Low Layer Private Macros |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Exported functions --------------------------------------------------------*/ |
| |
| /** @defgroup FMC_LL_Exported_Functions FMC Low Layer Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup FMC_NORSRAM FMC NORSRAM Controller functions |
| * @brief NORSRAM Controller functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use NORSRAM device driver ##### |
| ============================================================================== |
| |
| [..] |
| This driver contains a set of APIs to interface with the FMC NORSRAM banks in order |
| to run the NORSRAM external devices. |
| |
| (+) FMC NORSRAM bank reset using the function FMC_NORSRAM_DeInit() |
| (+) FMC NORSRAM bank control configuration using the function FMC_NORSRAM_Init() |
| (+) FMC NORSRAM bank timing configuration using the function FMC_NORSRAM_Timing_Init() |
| (+) FMC NORSRAM bank extended timing configuration using the function |
| FMC_NORSRAM_Extended_Timing_Init() |
| (+) FMC NORSRAM bank enable/disable write operation using the functions |
| FMC_NORSRAM_WriteOperation_Enable()/FMC_NORSRAM_WriteOperation_Disable() |
| |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** @defgroup FMC_NORSRAM_Group1 Initialization/de-initialization functions |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de_initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to: |
| (+) Initialize and configure the FMC NORSRAM interface |
| (+) De-initialize the FMC NORSRAM interface |
| (+) Configure the FMC clock and associated GPIOs |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initialize the FMC_NORSRAM device according to the specified |
| * control parameters in the FMC_NORSRAM_InitTypeDef |
| * @param Device Pointer to NORSRAM device instance |
| * @param Init Pointer to NORSRAM Initialization structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NORSRAM_Init(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_InitTypeDef *Init) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FMC_NORSRAM_BANK(Init->NSBank)); |
| assert_param(IS_FMC_MUX(Init->DataAddressMux)); |
| assert_param(IS_FMC_MEMORY(Init->MemoryType)); |
| assert_param(IS_FMC_NORSRAM_MEMORY_WIDTH(Init->MemoryDataWidth)); |
| assert_param(IS_FMC_BURSTMODE(Init->BurstAccessMode)); |
| assert_param(IS_FMC_WAIT_POLARITY(Init->WaitSignalPolarity)); |
| assert_param(IS_FMC_WRAP_MODE(Init->WrapMode)); |
| assert_param(IS_FMC_WAIT_SIGNAL_ACTIVE(Init->WaitSignalActive)); |
| assert_param(IS_FMC_WRITE_OPERATION(Init->WriteOperation)); |
| assert_param(IS_FMC_WAITE_SIGNAL(Init->WaitSignal)); |
| assert_param(IS_FMC_EXTENDED_MODE(Init->ExtendedMode)); |
| assert_param(IS_FMC_ASYNWAIT(Init->AsynchronousWait)); |
| assert_param(IS_FMC_WRITE_BURST(Init->WriteBurst)); |
| assert_param(IS_FMC_CONTINOUS_CLOCK(Init->ContinuousClock)); |
| |
| /* Disable NORSRAM Device */ |
| __FMC_NORSRAM_DISABLE(Device, Init->NSBank); |
| |
| /* Set NORSRAM device control parameters */ |
| if (Init->MemoryType == FMC_MEMORY_TYPE_NOR) |
| { |
| MODIFY_REG(Device->BTCR[Init->NSBank], BCR_CLEAR_MASK, (uint32_t)(FMC_NORSRAM_FLASH_ACCESS_ENABLE |
| | Init->DataAddressMux |
| | Init->MemoryType |
| | Init->MemoryDataWidth |
| | Init->BurstAccessMode |
| | Init->WaitSignalPolarity |
| | Init->WrapMode |
| | Init->WaitSignalActive |
| | Init->WriteOperation |
| | Init->WaitSignal |
| | Init->ExtendedMode |
| | Init->AsynchronousWait |
| | Init->WriteBurst |
| | Init->ContinuousClock |
| ) |
| ); |
| } |
| else |
| { |
| MODIFY_REG(Device->BTCR[Init->NSBank], BCR_CLEAR_MASK, (uint32_t)(FMC_NORSRAM_FLASH_ACCESS_DISABLE |
| | Init->DataAddressMux |
| | Init->MemoryType |
| | Init->MemoryDataWidth |
| | Init->BurstAccessMode |
| | Init->WaitSignalPolarity |
| | Init->WrapMode |
| | Init->WaitSignalActive |
| | Init->WriteOperation |
| | Init->WaitSignal |
| | Init->ExtendedMode |
| | Init->AsynchronousWait |
| | Init->WriteBurst |
| | Init->ContinuousClock |
| ) |
| ); |
| } |
| |
| /* Configure synchronous mode when Continuous clock is enabled for bank2..4 */ |
| if ((Init->ContinuousClock == FMC_CONTINUOUS_CLOCK_SYNC_ASYNC) && (Init->NSBank != FMC_NORSRAM_BANK1)) |
| { |
| MODIFY_REG(Device->BTCR[FMC_NORSRAM_BANK1], FMC_BCR1_CCLKEN, Init->ContinuousClock); |
| } |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief DeInitialize the FMC_NORSRAM peripheral |
| * @param Device Pointer to NORSRAM device instance |
| * @param ExDevice Pointer to NORSRAM extended mode device instance |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NORSRAM_DeInit(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_EXTENDED_TypeDef *ExDevice, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FMC_NORSRAM_EXTENDED_DEVICE(ExDevice)); |
| assert_param(IS_FMC_NORSRAM_BANK(Bank)); |
| |
| /* Disable the FMC_NORSRAM device */ |
| __FMC_NORSRAM_DISABLE(Device, Bank); |
| |
| /* De-initialize the FMC_NORSRAM device */ |
| /* FMC_NORSRAM_BANK1 */ |
| if (Bank == FMC_NORSRAM_BANK1) |
| { |
| Device->BTCR[Bank] = 0x000030DB; |
| } |
| /* FMC_NORSRAM_BANK2, FMC_NORSRAM_BANK3 or FMC_NORSRAM_BANK4 */ |
| else |
| { |
| Device->BTCR[Bank] = 0x000030D2; |
| } |
| |
| Device->BTCR[Bank + 1] = 0x0FFFFFFF; |
| ExDevice->BWTR[Bank] = 0x0FFFFFFF; |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief Initialize the FMC_NORSRAM Timing according to the specified |
| * parameters in the FMC_NORSRAM_TimingTypeDef |
| * @param Device Pointer to NORSRAM device instance |
| * @param Timing Pointer to NORSRAM Timing structure |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NORSRAM_Timing_Init(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank) |
| { |
| uint32_t tmpr = 0; |
| |
| /* Check the parameters */ |
| assert_param(IS_FMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime)); |
| assert_param(IS_FMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime)); |
| assert_param(IS_FMC_DATASETUP_TIME(Timing->DataSetupTime)); |
| assert_param(IS_FMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration)); |
| assert_param(IS_FMC_CLK_DIV(Timing->CLKDivision)); |
| assert_param(IS_FMC_DATA_LATENCY(Timing->DataLatency)); |
| assert_param(IS_FMC_ACCESS_MODE(Timing->AccessMode)); |
| assert_param(IS_FMC_NORSRAM_BANK(Bank)); |
| |
| /* Set FMC_NORSRAM device timing parameters */ |
| MODIFY_REG(Device->BTCR[Bank + 1], \ |
| BTR_CLEAR_MASK, \ |
| (uint32_t)(Timing->AddressSetupTime | \ |
| ((Timing->AddressHoldTime) << POSITION_VAL(FMC_BTRx_ADDHLD)) | \ |
| ((Timing->DataSetupTime) << POSITION_VAL(FMC_BTRx_DATAST)) | \ |
| ((Timing->BusTurnAroundDuration) << POSITION_VAL(FMC_BTRx_BUSTURN)) | \ |
| (((Timing->CLKDivision) - 1) << POSITION_VAL(FMC_BTRx_CLKDIV)) | \ |
| (((Timing->DataLatency) - 2) << POSITION_VAL(FMC_BTRx_DATLAT)) | \ |
| (Timing->AccessMode))); |
| |
| /* Configure Clock division value (in NORSRAM bank 1) when continuous clock is enabled */ |
| if (HAL_IS_BIT_SET(Device->BTCR[FMC_NORSRAM_BANK1], FMC_BCR1_CCLKEN)) |
| { |
| tmpr = (uint32_t)(Device->BTCR[FMC_NORSRAM_BANK1 + 1] & ~(((uint32_t)0x0F) << POSITION_VAL(FMC_BTRx_CLKDIV))); |
| tmpr |= (uint32_t)(((Timing->CLKDivision) - 1) << POSITION_VAL(FMC_BTRx_CLKDIV)); |
| MODIFY_REG(Device->BTCR[FMC_NORSRAM_BANK1 + 1], FMC_BTRx_CLKDIV, tmpr); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initialize the FMC_NORSRAM Extended mode Timing according to the specified |
| * parameters in the FMC_NORSRAM_TimingTypeDef |
| * @param Device Pointer to NORSRAM device instance |
| * @param Timing Pointer to NORSRAM Timing structure |
| * @param Bank NORSRAM bank number |
| * @param ExtendedMode FMC Extended Mode |
| * This parameter can be one of the following values: |
| * @arg FMC_EXTENDED_MODE_DISABLE |
| * @arg FMC_EXTENDED_MODE_ENABLE |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NORSRAM_Extended_Timing_Init(FMC_NORSRAM_EXTENDED_TypeDef *Device, FMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank, uint32_t ExtendedMode) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_EXTENDED_MODE(ExtendedMode)); |
| |
| /* Set NORSRAM device timing register for write configuration, if extended mode is used */ |
| if (ExtendedMode == FMC_EXTENDED_MODE_ENABLE) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NORSRAM_EXTENDED_DEVICE(Device)); |
| assert_param(IS_FMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime)); |
| assert_param(IS_FMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime)); |
| assert_param(IS_FMC_DATASETUP_TIME(Timing->DataSetupTime)); |
| assert_param(IS_FMC_ACCESS_MODE(Timing->AccessMode)); |
| assert_param(IS_FMC_NORSRAM_BANK(Bank)); |
| |
| /* Set NORSRAM device timing register for write configuration, if extended mode is used */ |
| MODIFY_REG(Device->BWTR[Bank], \ |
| BWTR_CLEAR_MASK, \ |
| (uint32_t)(Timing->AddressSetupTime | \ |
| ((Timing->AddressHoldTime) << POSITION_VAL(FMC_BWTRx_ADDHLD)) | \ |
| ((Timing->DataSetupTime) << POSITION_VAL(FMC_BWTRx_DATAST)) | \ |
| (Timing->AccessMode))); |
| } |
| else |
| { |
| Device->BWTR[Bank] = 0x0FFFFFFF; |
| } |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup FMC_NORSRAM_Group2 Control functions |
| * @brief management functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### FMC_NORSRAM Control functions ##### |
| ============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to control dynamically |
| the FMC NORSRAM interface. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Enables dynamically FMC_NORSRAM write operation. |
| * @param Device Pointer to NORSRAM device instance |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NORSRAM_WriteOperation_Enable(FMC_NORSRAM_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FMC_NORSRAM_BANK(Bank)); |
| |
| /* Enable write operation */ |
| SET_BIT(Device->BTCR[Bank], FMC_WRITE_OPERATION_ENABLE); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Disables dynamically FMC_NORSRAM write operation. |
| * @param Device Pointer to NORSRAM device instance |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NORSRAM_WriteOperation_Disable(FMC_NORSRAM_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FMC_NORSRAM_BANK(Bank)); |
| |
| /* Disable write operation */ |
| CLEAR_BIT(Device->BTCR[Bank], FMC_WRITE_OPERATION_ENABLE); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| /** @defgroup FMC_NAND FMC NAND Controller functions |
| * @brief NAND Controller functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use NAND device driver ##### |
| ============================================================================== |
| [..] |
| This driver contains a set of APIs to interface with the FMC NAND banks in order |
| to run the NAND external devices. |
| |
| (+) FMC NAND bank reset using the function FMC_NAND_DeInit() |
| (+) FMC NAND bank control configuration using the function FMC_NAND_Init() |
| (+) FMC NAND bank common space timing configuration using the function |
| FMC_NAND_CommonSpace_Timing_Init() |
| (+) FMC NAND bank attribute space timing configuration using the function |
| FMC_NAND_AttributeSpace_Timing_Init() |
| (+) FMC NAND bank enable/disable ECC correction feature using the functions |
| FMC_NAND_ECC_Enable()/FMC_NAND_ECC_Disable() |
| (+) FMC NAND bank get ECC correction code using the function FMC_NAND_GetECC() |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** @defgroup FMC_NAND_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de_initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to: |
| (+) Initialize and configure the FMC NAND interface |
| (+) De-initialize the FMC NAND interface |
| (+) Configure the FMC clock and associated GPIOs |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the FMC_NAND device according to the specified |
| * control parameters in the FMC_NAND_HandleTypeDef |
| * @param Device Pointer to NAND device instance |
| * @param Init Pointer to NAND Initialization structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_Init(FMC_NAND_TypeDef *Device, FMC_NAND_InitTypeDef *Init) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_NAND_BANK(Init->NandBank)); |
| assert_param(IS_FMC_WAIT_FEATURE(Init->Waitfeature)); |
| assert_param(IS_FMC_NAND_MEMORY_WIDTH(Init->MemoryDataWidth)); |
| assert_param(IS_FMC_ECC_STATE(Init->EccComputation)); |
| assert_param(IS_FMC_ECCPAGE_SIZE(Init->ECCPageSize)); |
| assert_param(IS_FMC_TCLR_TIME(Init->TCLRSetupTime)); |
| assert_param(IS_FMC_TAR_TIME(Init->TARSetupTime)); |
| |
| /* Set NAND device control parameters */ |
| if (Init->NandBank == FMC_NAND_BANK2) |
| { |
| /* NAND bank 2 registers configuration */ |
| MODIFY_REG(Device->PCR2, PCR_CLEAR_MASK, (Init->Waitfeature | |
| FMC_PCR_MEMORY_TYPE_NAND | |
| Init->MemoryDataWidth | |
| Init->EccComputation | |
| Init->ECCPageSize | |
| ((Init->TCLRSetupTime) << POSITION_VAL(FMC_PCRx_TCLR)) | |
| ((Init->TARSetupTime) << POSITION_VAL(FMC_PCRx_TAR)))); |
| } |
| else |
| { |
| /* NAND bank 3 registers configuration */ |
| MODIFY_REG(Device->PCR3, PCR_CLEAR_MASK, (Init->Waitfeature | |
| FMC_PCR_MEMORY_TYPE_NAND | |
| Init->MemoryDataWidth | |
| Init->EccComputation | |
| Init->ECCPageSize | |
| ((Init->TCLRSetupTime) << POSITION_VAL(FMC_PCRx_TCLR)) | |
| ((Init->TARSetupTime) << POSITION_VAL(FMC_PCRx_TAR)))); |
| } |
| |
| return HAL_OK; |
| |
| } |
| |
| /** |
| * @brief Initializes the FMC_NAND Common space Timing according to the specified |
| * parameters in the FMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to NAND device instance |
| * @param Timing Pointer to NAND timing structure |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_CommonSpace_Timing_Init(FMC_NAND_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime)); |
| assert_param(IS_FMC_NAND_BANK(Bank)); |
| |
| /* Set FMC_NAND device timing parameters */ |
| if (Bank == FMC_NAND_BANK2) |
| { |
| /* NAND bank 2 registers configuration */ |
| MODIFY_REG(Device->PMEM2, PMEM_CLEAR_MASK, (Timing->SetupTime | \ |
| ((Timing->WaitSetupTime) << POSITION_VAL(FMC_PMEMx_MEMWAITx)) | \ |
| ((Timing->HoldSetupTime) << POSITION_VAL(FMC_PMEMx_MEMHOLDx)) | \ |
| ((Timing->HiZSetupTime) << POSITION_VAL(FMC_PMEMx_MEMHIZx)))); |
| } |
| else |
| { |
| /* NAND bank 3 registers configuration */ |
| MODIFY_REG(Device->PMEM3, PMEM_CLEAR_MASK, (Timing->SetupTime | \ |
| ((Timing->WaitSetupTime) << POSITION_VAL(FMC_PMEMx_MEMWAITx)) | \ |
| ((Timing->HoldSetupTime) << POSITION_VAL(FMC_PMEMx_MEMHOLDx)) | \ |
| ((Timing->HiZSetupTime) << POSITION_VAL(FMC_PMEMx_MEMHIZx)))); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FMC_NAND Attribute space Timing according to the specified |
| * parameters in the FMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to NAND device instance |
| * @param Timing Pointer to NAND timing structure |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_AttributeSpace_Timing_Init(FMC_NAND_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime)); |
| assert_param(IS_FMC_NAND_BANK(Bank)); |
| |
| /* Set FMC_NAND device timing parameters */ |
| if (Bank == FMC_NAND_BANK2) |
| { |
| /* NAND bank 2 registers configuration */ |
| MODIFY_REG(Device->PATT2, PATT_CLEAR_MASK, (Timing->SetupTime | \ |
| ((Timing->WaitSetupTime) << POSITION_VAL(FMC_PATTx_ATTWAITx)) | \ |
| ((Timing->HoldSetupTime) << POSITION_VAL(FMC_PATTx_ATTHOLDx)) | \ |
| ((Timing->HiZSetupTime) << POSITION_VAL(FMC_PATTx_ATTHIZx)))); |
| } |
| else |
| { |
| /* NAND bank 3 registers configuration */ |
| MODIFY_REG(Device->PATT3, PATT_CLEAR_MASK, (Timing->SetupTime | \ |
| ((Timing->WaitSetupTime) << POSITION_VAL(FMC_PATTx_ATTWAITx)) | \ |
| ((Timing->HoldSetupTime) << POSITION_VAL(FMC_PATTx_ATTHOLDx)) | \ |
| ((Timing->HiZSetupTime) << POSITION_VAL(FMC_PATTx_ATTHIZx)))); |
| } |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief DeInitialize the FMC_NAND device |
| * @param Device Pointer to NAND device instance |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_DeInit(FMC_NAND_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_NAND_BANK(Bank)); |
| |
| /* Disable the NAND Bank */ |
| __FMC_NAND_DISABLE(Device, Bank); |
| |
| /* De-initialize the NAND Bank */ |
| if (Bank == FMC_NAND_BANK2) |
| { |
| /* Set the FMC_NAND_BANK2 registers to their reset values */ |
| WRITE_REG(Device->PCR2, 0x00000018); |
| WRITE_REG(Device->SR2, 0x00000040); |
| WRITE_REG(Device->PMEM2, 0xFCFCFCFC); |
| WRITE_REG(Device->PATT2, 0xFCFCFCFC); |
| } |
| /* FMC_Bank3_NAND */ |
| else |
| { |
| /* Set the FMC_NAND_BANK3 registers to their reset values */ |
| WRITE_REG(Device->PCR3, 0x00000018); |
| WRITE_REG(Device->SR3, 0x00000040); |
| WRITE_REG(Device->PMEM3, 0xFCFCFCFC); |
| WRITE_REG(Device->PATT3, 0xFCFCFCFC); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup FMC_NAND_Exported_Functions_Group2 Peripheral Control functions |
| * @brief management functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### FMC_NAND Control functions ##### |
| ============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to control dynamically |
| the FMC NAND interface. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| |
| /** |
| * @brief Enables dynamically FMC_NAND ECC feature. |
| * @param Device Pointer to NAND device instance |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_ECC_Enable(FMC_NAND_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_NAND_BANK(Bank)); |
| |
| /* Enable ECC feature */ |
| if (Bank == FMC_NAND_BANK2) |
| { |
| SET_BIT(Device->PCR2, FMC_PCRx_ECCEN); |
| } |
| else |
| { |
| SET_BIT(Device->PCR3, FMC_PCRx_ECCEN); |
| } |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief Disables dynamically FMC_NAND ECC feature. |
| * @param Device Pointer to NAND device instance |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_ECC_Disable(FMC_NAND_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_NAND_BANK(Bank)); |
| |
| /* Disable ECC feature */ |
| if (Bank == FMC_NAND_BANK2) |
| { |
| CLEAR_BIT(Device->PCR2, FMC_PCRx_ECCEN); |
| } |
| else |
| { |
| CLEAR_BIT(Device->PCR3, FMC_PCRx_ECCEN); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Disables dynamically FMC_NAND ECC feature. |
| * @param Device Pointer to NAND device instance |
| * @param ECCval Pointer to ECC value |
| * @param Bank NAND bank number |
| * @param Timeout Timeout wait value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_NAND_GetECC(FMC_NAND_TypeDef *Device, uint32_t *ECCval, uint32_t Bank, uint32_t Timeout) |
| { |
| uint32_t tickstart = 0; |
| |
| /* Check the parameters */ |
| assert_param(IS_FMC_NAND_DEVICE(Device)); |
| assert_param(IS_FMC_NAND_BANK(Bank)); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait until FIFO is empty */ |
| while (__FMC_NAND_GET_FLAG(Device, Bank, FMC_FLAG_FEMPT) == RESET) |
| { |
| /* Check for the Timeout */ |
| if (Timeout != HAL_MAX_DELAY) |
| { |
| if ((Timeout == 0) || ((HAL_GetTick() - tickstart) > Timeout)) |
| { |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| if (Bank == FMC_NAND_BANK2) |
| { |
| /* Get the ECCR2 register value */ |
| *ECCval = (uint32_t)Device->ECCR2; |
| } |
| else |
| { |
| /* Get the ECCR3 register value */ |
| *ECCval = (uint32_t)Device->ECCR3; |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup FMC_PCCARD FMC PCCARD Controller functions |
| * @brief PCCARD Controller functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use PCCARD device driver ##### |
| ============================================================================== |
| [..] |
| This driver contains a set of APIs to interface with the FMC PCCARD bank in order |
| to run the PCCARD/compact flash external devices. |
| |
| (+) FMC PCCARD bank reset using the function FMC_PCCARD_DeInit() |
| (+) FMC PCCARD bank control configuration using the function FMC_PCCARD_Init() |
| (+) FMC PCCARD bank common space timing configuration using the function |
| FMC_PCCARD_CommonSpace_Timing_Init() |
| (+) FMC PCCARD bank attribute space timing configuration using the function |
| FMC_PCCARD_AttributeSpace_Timing_Init() |
| (+) FMC PCCARD bank IO space timing configuration using the function |
| FMC_PCCARD_IOSpace_Timing_Init() |
| |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** @defgroup FMC_PCCARD_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de_initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to: |
| (+) Initialize and configure the FMC PCCARD interface |
| (+) De-initialize the FMC PCCARD interface |
| (+) Configure the FMC clock and associated GPIOs |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the FMC_PCCARD device according to the specified |
| * control parameters in the FMC_PCCARD_HandleTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Init Pointer to PCCARD Initialization structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_PCCARD_Init(FMC_PCCARD_TypeDef *Device, FMC_PCCARD_InitTypeDef *Init) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_PCCARD_DEVICE(Device)); |
| assert_param(IS_FMC_WAIT_FEATURE(Init->Waitfeature)); |
| assert_param(IS_FMC_TCLR_TIME(Init->TCLRSetupTime)); |
| assert_param(IS_FMC_TAR_TIME(Init->TARSetupTime)); |
| |
| /* Set FMC_PCCARD device control parameters */ |
| MODIFY_REG(Device->PCR4, |
| (FMC_PCRx_PTYP | FMC_PCRx_PWAITEN | FMC_PCRx_PWID | |
| FMC_PCRx_TCLR | FMC_PCRx_TAR), |
| (FMC_PCR_MEMORY_TYPE_PCCARD | |
| Init->Waitfeature | |
| FMC_NAND_PCC_MEM_BUS_WIDTH_16 | |
| (Init->TCLRSetupTime << POSITION_VAL(FMC_PCRx_TCLR)) | |
| (Init->TARSetupTime << POSITION_VAL(FMC_PCRx_TAR)))); |
| |
| return HAL_OK; |
| |
| } |
| |
| /** |
| * @brief Initializes the FMC_PCCARD Common space Timing according to the specified |
| * parameters in the FMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Timing Pointer to PCCARD timing structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_PCCARD_CommonSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_PCCARD_DEVICE(Device)); |
| assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime)); |
| |
| /* Set PCCARD timing parameters */ |
| MODIFY_REG(Device->PMEM4, PMEM_CLEAR_MASK, |
| (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << POSITION_VAL(FMC_PMEMx_MEMWAITx)) | |
| ((Timing->HoldSetupTime) << POSITION_VAL(FMC_PMEMx_MEMHOLDx)) | |
| ((Timing->HiZSetupTime) << POSITION_VAL(FMC_PMEMx_MEMHIZx)))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FMC_PCCARD Attribute space Timing according to the specified |
| * parameters in the FMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Timing Pointer to PCCARD timing structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_PCCARD_AttributeSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_PCCARD_DEVICE(Device)); |
| assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime)); |
| |
| /* Set PCCARD timing parameters */ |
| MODIFY_REG(Device->PATT4, PATT_CLEAR_MASK, \ |
| (Timing->SetupTime | \ |
| ((Timing->WaitSetupTime) << POSITION_VAL(FMC_PATTx_ATTWAITx)) | \ |
| ((Timing->HoldSetupTime) << POSITION_VAL(FMC_PATTx_ATTHOLDx)) | \ |
| ((Timing->HiZSetupTime) << POSITION_VAL(FMC_PATTx_ATTHIZx)))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FMC_PCCARD IO space Timing according to the specified |
| * parameters in the FMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Timing Pointer to PCCARD timing structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_PCCARD_IOSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_PCCARD_DEVICE(Device)); |
| assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime)); |
| |
| /* Set FMC_PCCARD device timing parameters */ |
| MODIFY_REG(Device->PIO4, PIO4_CLEAR_MASK, \ |
| (Timing->SetupTime | \ |
| (Timing->WaitSetupTime << POSITION_VAL(FMC_PIO4_IOWAIT4)) | \ |
| (Timing->HoldSetupTime << POSITION_VAL(FMC_PIO4_IOHOLD4)) | \ |
| (Timing->HiZSetupTime << POSITION_VAL(FMC_PIO4_IOHIZ4)))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief DeInitialize the FMC_PCCARD device |
| * @param Device Pointer to PCCARD device instance |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FMC_PCCARD_DeInit(FMC_PCCARD_TypeDef *Device) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FMC_PCCARD_DEVICE(Device)); |
| |
| /* Disable the FMC_PCCARD device */ |
| __FMC_PCCARD_DISABLE(Device); |
| |
| /* De-initialize the FMC_PCCARD device */ |
| WRITE_REG(Device->PCR4, 0x00000018); |
| WRITE_REG(Device->SR4, 0x00000040); |
| WRITE_REG(Device->PMEM4, 0xFCFCFCFC); |
| WRITE_REG(Device->PATT4, 0xFCFCFCFC); |
| WRITE_REG(Device->PIO4, 0xFCFCFCFC); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* defined(HAL_SRAM_MODULE_ENABLED) || defined(HAL_NOR_MODULE_ENABLED) || defined(HAL_PCCARD_MODULE_ENABLED) || defined(HAL_NAND_MODULE_ENABLED) */ |
| |
| #endif /* FMC_BANK1 */ |
| |
| /** |
| * @} |
| */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
