| /** |
| ****************************************************************************** |
| * @file stm32f4xx_ll_fsmc.c |
| * @author MCD Application Team |
| * @brief FSMC Low Layer HAL module driver. |
| * |
| * This file provides firmware functions to manage the following |
| * functionalities of the Flexible Memory Controller (FSMC) peripheral memories: |
| * + Initialization/de-initialization functions |
| * + Peripheral Control functions |
| * + Peripheral State functions |
| * |
| ****************************************************************************** |
| * @attention |
| * |
| * Copyright (c) 2016 STMicroelectronics. |
| * All rights reserved. |
| * |
| * This software is licensed under terms that can be found in the LICENSE file |
| * in the root directory of this software component. |
| * If no LICENSE file comes with this software, it is provided AS-IS. |
| * |
| ****************************************************************************** |
| @verbatim |
| ============================================================================== |
| ##### FSMC peripheral features ##### |
| ============================================================================== |
| [..] The Flexible memory controller (FSMC) includes following memory controllers: |
| (+) The NOR/PSRAM memory controller |
| (+) The NAND/PC Card memory controller |
| |
| [..] The FSMC functional block makes the interface with synchronous and asynchronous static |
| memories and 16-bit PC memory cards. Its main purposes are: |
| (+) to translate AHB transactions into the appropriate external device protocol |
| (+) to meet the access time requirements of the external memory devices |
| |
| [..] All external memories share the addresses, data and control signals with the controller. |
| Each external device is accessed by means of a unique Chip Select. The FSMC performs |
| only one access at a time to an external device. |
| The main features of the FSMC controller are the following: |
| (+) Interface with static-memory mapped devices including: |
| (++) Static random access memory (SRAM) |
| (++) Read-only memory (ROM) |
| (++) NOR Flash memory/OneNAND Flash memory |
| (++) PSRAM (4 memory banks) |
| (++) 16-bit PC Card compatible devices |
| (++) Two banks of NAND Flash memory with ECC hardware to check up to 8 Kbytes of |
| data |
| (+) Independent Chip Select control for each memory bank |
| (+) Independent configuration for each memory bank |
| |
| @endverbatim |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f4xx_hal.h" |
| |
| /** @addtogroup STM32F4xx_HAL_Driver |
| * @{ |
| */ |
| #if defined(HAL_NOR_MODULE_ENABLED) || defined(HAL_SRAM_MODULE_ENABLED) || defined(HAL_NAND_MODULE_ENABLED) || defined(HAL_PCCARD_MODULE_ENABLED) |
| |
| /** @defgroup FSMC_LL FSMC Low Layer |
| * @brief FSMC driver modules |
| * @{ |
| */ |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| |
| /** @defgroup FSMC_LL_Private_Constants FSMC Low Layer Private Constants |
| * @{ |
| */ |
| |
| /* ----------------------- FSMC registers bit mask --------------------------- */ |
| |
| #if defined(FSMC_Bank1) |
| /* --- BCR Register ---*/ |
| /* BCR register clear mask */ |
| |
| /* --- BTR Register ---*/ |
| /* BTR register clear mask */ |
| #define BTR_CLEAR_MASK ((uint32_t)(FSMC_BTR1_ADDSET | FSMC_BTR1_ADDHLD |\ |
| FSMC_BTR1_DATAST | FSMC_BTR1_BUSTURN |\ |
| FSMC_BTR1_CLKDIV | FSMC_BTR1_DATLAT |\ |
| FSMC_BTR1_ACCMOD)) |
| |
| /* --- BWTR Register ---*/ |
| /* BWTR register clear mask */ |
| #define BWTR_CLEAR_MASK ((uint32_t)(FSMC_BWTR1_ADDSET | FSMC_BWTR1_ADDHLD |\ |
| FSMC_BWTR1_DATAST | FSMC_BWTR1_BUSTURN |\ |
| FSMC_BWTR1_ACCMOD)) |
| #endif /* FSMC_Bank1 */ |
| #if defined(FSMC_Bank2_3) |
| |
| #if defined (FSMC_PCR_PWAITEN) |
| /* --- PCR Register ---*/ |
| /* PCR register clear mask */ |
| #define PCR_CLEAR_MASK ((uint32_t)(FSMC_PCR_PWAITEN | FSMC_PCR_PBKEN | \ |
| FSMC_PCR_PTYP | FSMC_PCR_PWID | \ |
| FSMC_PCR_ECCEN | FSMC_PCR_TCLR | \ |
| FSMC_PCR_TAR | FSMC_PCR_ECCPS)) |
| /* --- PMEM Register ---*/ |
| /* PMEM register clear mask */ |
| #define PMEM_CLEAR_MASK ((uint32_t)(FSMC_PMEM_MEMSET2 | FSMC_PMEM_MEMWAIT2 |\ |
| FSMC_PMEM_MEMHOLD2 | FSMC_PMEM_MEMHIZ2)) |
| |
| /* --- PATT Register ---*/ |
| /* PATT register clear mask */ |
| #define PATT_CLEAR_MASK ((uint32_t)(FSMC_PATT_ATTSET2 | FSMC_PATT_ATTWAIT2 |\ |
| FSMC_PATT_ATTHOLD2 | FSMC_PATT_ATTHIZ2)) |
| #else |
| /* --- PCR Register ---*/ |
| /* PCR register clear mask */ |
| #define PCR_CLEAR_MASK ((uint32_t)(FSMC_PCR2_PWAITEN | FSMC_PCR2_PBKEN | \ |
| FSMC_PCR2_PTYP | FSMC_PCR2_PWID | \ |
| FSMC_PCR2_ECCEN | FSMC_PCR2_TCLR | \ |
| FSMC_PCR2_TAR | FSMC_PCR2_ECCPS)) |
| /* --- PMEM Register ---*/ |
| /* PMEM register clear mask */ |
| #define PMEM_CLEAR_MASK ((uint32_t)(FSMC_PMEM2_MEMSET2 | FSMC_PMEM2_MEMWAIT2 |\ |
| FSMC_PMEM2_MEMHOLD2 | FSMC_PMEM2_MEMHIZ2)) |
| |
| /* --- PATT Register ---*/ |
| /* PATT register clear mask */ |
| #define PATT_CLEAR_MASK ((uint32_t)(FSMC_PATT2_ATTSET2 | FSMC_PATT2_ATTWAIT2 |\ |
| FSMC_PATT2_ATTHOLD2 | FSMC_PATT2_ATTHIZ2)) |
| |
| #endif /* FSMC_PCR_PWAITEN */ |
| #endif /* FSMC_Bank2_3 */ |
| #if defined(FSMC_Bank4) |
| /* --- PCR Register ---*/ |
| /* PCR register clear mask */ |
| #define PCR4_CLEAR_MASK ((uint32_t)(FSMC_PCR4_PWAITEN | FSMC_PCR4_PBKEN | \ |
| FSMC_PCR4_PTYP | FSMC_PCR4_PWID | \ |
| FSMC_PCR4_ECCEN | FSMC_PCR4_TCLR | \ |
| FSMC_PCR4_TAR | FSMC_PCR4_ECCPS)) |
| /* --- PMEM Register ---*/ |
| /* PMEM register clear mask */ |
| #define PMEM4_CLEAR_MASK ((uint32_t)(FSMC_PMEM4_MEMSET4 | FSMC_PMEM4_MEMWAIT4 |\ |
| FSMC_PMEM4_MEMHOLD4 | FSMC_PMEM4_MEMHIZ4)) |
| |
| /* --- PATT Register ---*/ |
| /* PATT register clear mask */ |
| #define PATT4_CLEAR_MASK ((uint32_t)(FSMC_PATT4_ATTSET4 | FSMC_PATT4_ATTWAIT4 |\ |
| FSMC_PATT4_ATTHOLD4 | FSMC_PATT4_ATTHIZ4)) |
| |
| /* --- PIO4 Register ---*/ |
| /* PIO4 register clear mask */ |
| #define PIO4_CLEAR_MASK ((uint32_t)(FSMC_PIO4_IOSET4 | FSMC_PIO4_IOWAIT4 | \ |
| FSMC_PIO4_IOHOLD4 | FSMC_PIO4_IOHIZ4)) |
| |
| #endif /* FSMC_Bank4 */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Exported functions --------------------------------------------------------*/ |
| |
| /** @defgroup FSMC_LL_Exported_Functions FSMC Low Layer Exported Functions |
| * @{ |
| */ |
| |
| #if defined(FSMC_Bank1) |
| |
| /** @defgroup FSMC_LL_Exported_Functions_NORSRAM FSMC Low Layer NOR SRAM Exported Functions |
| * @brief NORSRAM Controller functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use NORSRAM device driver ##### |
| ============================================================================== |
| |
| [..] |
| This driver contains a set of APIs to interface with the FSMC NORSRAM banks in order |
| to run the NORSRAM external devices. |
| |
| (+) FSMC NORSRAM bank reset using the function FSMC_NORSRAM_DeInit() |
| (+) FSMC NORSRAM bank control configuration using the function FSMC_NORSRAM_Init() |
| (+) FSMC NORSRAM bank timing configuration using the function FSMC_NORSRAM_Timing_Init() |
| (+) FSMC NORSRAM bank extended timing configuration using the function |
| FSMC_NORSRAM_Extended_Timing_Init() |
| (+) FSMC NORSRAM bank enable/disable write operation using the functions |
| FSMC_NORSRAM_WriteOperation_Enable()/FSMC_NORSRAM_WriteOperation_Disable() |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** @defgroup FSMC_LL_NORSRAM_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de_initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to: |
| (+) Initialize and configure the FSMC NORSRAM interface |
| (+) De-initialize the FSMC NORSRAM interface |
| (+) Configure the FSMC clock and associated GPIOs |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initialize the FSMC_NORSRAM device according to the specified |
| * control parameters in the FSMC_NORSRAM_InitTypeDef |
| * @param Device Pointer to NORSRAM device instance |
| * @param Init Pointer to NORSRAM Initialization structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NORSRAM_Init(FSMC_NORSRAM_TypeDef *Device, |
| FSMC_NORSRAM_InitTypeDef *Init) |
| { |
| uint32_t flashaccess; |
| uint32_t btcr_reg; |
| uint32_t mask; |
| |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FSMC_NORSRAM_BANK(Init->NSBank)); |
| assert_param(IS_FSMC_MUX(Init->DataAddressMux)); |
| assert_param(IS_FSMC_MEMORY(Init->MemoryType)); |
| assert_param(IS_FSMC_NORSRAM_MEMORY_WIDTH(Init->MemoryDataWidth)); |
| assert_param(IS_FSMC_BURSTMODE(Init->BurstAccessMode)); |
| assert_param(IS_FSMC_WAIT_POLARITY(Init->WaitSignalPolarity)); |
| #if defined(FSMC_BCR1_WRAPMOD) |
| assert_param(IS_FSMC_WRAP_MODE(Init->WrapMode)); |
| #endif /* FSMC_BCR1_WRAPMOD */ |
| assert_param(IS_FSMC_WAIT_SIGNAL_ACTIVE(Init->WaitSignalActive)); |
| assert_param(IS_FSMC_WRITE_OPERATION(Init->WriteOperation)); |
| assert_param(IS_FSMC_WAITE_SIGNAL(Init->WaitSignal)); |
| assert_param(IS_FSMC_EXTENDED_MODE(Init->ExtendedMode)); |
| assert_param(IS_FSMC_ASYNWAIT(Init->AsynchronousWait)); |
| assert_param(IS_FSMC_WRITE_BURST(Init->WriteBurst)); |
| #if defined(FSMC_BCR1_CCLKEN) |
| assert_param(IS_FSMC_CONTINOUS_CLOCK(Init->ContinuousClock)); |
| #endif |
| #if defined(FSMC_BCR1_WFDIS) |
| assert_param(IS_FSMC_WRITE_FIFO(Init->WriteFifo)); |
| #endif /* FSMC_BCR1_WFDIS */ |
| assert_param(IS_FSMC_PAGESIZE(Init->PageSize)); |
| |
| /* Disable NORSRAM Device */ |
| __FSMC_NORSRAM_DISABLE(Device, Init->NSBank); |
| |
| /* Set NORSRAM device control parameters */ |
| if (Init->MemoryType == FSMC_MEMORY_TYPE_NOR) |
| { |
| flashaccess = FSMC_NORSRAM_FLASH_ACCESS_ENABLE; |
| } |
| else |
| { |
| flashaccess = FSMC_NORSRAM_FLASH_ACCESS_DISABLE; |
| } |
| |
| btcr_reg = (flashaccess | \ |
| Init->DataAddressMux | \ |
| Init->MemoryType | \ |
| Init->MemoryDataWidth | \ |
| Init->BurstAccessMode | \ |
| Init->WaitSignalPolarity | \ |
| Init->WaitSignalActive | \ |
| Init->WriteOperation | \ |
| Init->WaitSignal | \ |
| Init->ExtendedMode | \ |
| Init->AsynchronousWait | \ |
| Init->WriteBurst); |
| |
| #if defined(FSMC_BCR1_WRAPMOD) |
| btcr_reg |= Init->WrapMode; |
| #endif /* FSMC_BCR1_WRAPMOD */ |
| #if defined(FSMC_BCR1_CCLKEN) |
| btcr_reg |= Init->ContinuousClock; |
| #endif /* FSMC_BCR1_CCLKEN */ |
| #if defined(FSMC_BCR1_WFDIS) |
| btcr_reg |= Init->WriteFifo; |
| #endif /* FSMC_BCR1_WFDIS */ |
| btcr_reg |= Init->PageSize; |
| |
| mask = (FSMC_BCR1_MBKEN | |
| FSMC_BCR1_MUXEN | |
| FSMC_BCR1_MTYP | |
| FSMC_BCR1_MWID | |
| FSMC_BCR1_FACCEN | |
| FSMC_BCR1_BURSTEN | |
| FSMC_BCR1_WAITPOL | |
| FSMC_BCR1_WAITCFG | |
| FSMC_BCR1_WREN | |
| FSMC_BCR1_WAITEN | |
| FSMC_BCR1_EXTMOD | |
| FSMC_BCR1_ASYNCWAIT | |
| FSMC_BCR1_CBURSTRW); |
| |
| #if defined(FSMC_BCR1_WRAPMOD) |
| mask |= FSMC_BCR1_WRAPMOD; |
| #endif /* FSMC_BCR1_WRAPMOD */ |
| #if defined(FSMC_BCR1_CCLKEN) |
| mask |= FSMC_BCR1_CCLKEN; |
| #endif |
| #if defined(FSMC_BCR1_WFDIS) |
| mask |= FSMC_BCR1_WFDIS; |
| #endif /* FSMC_BCR1_WFDIS */ |
| mask |= FSMC_BCR1_CPSIZE; |
| |
| MODIFY_REG(Device->BTCR[Init->NSBank], mask, btcr_reg); |
| |
| #if defined(FSMC_BCR1_CCLKEN) |
| /* Configure synchronous mode when Continuous clock is enabled for bank2..4 */ |
| if ((Init->ContinuousClock == FSMC_CONTINUOUS_CLOCK_SYNC_ASYNC) && (Init->NSBank != FSMC_NORSRAM_BANK1)) |
| { |
| MODIFY_REG(Device->BTCR[FSMC_NORSRAM_BANK1], FSMC_BCR1_CCLKEN, Init->ContinuousClock); |
| } |
| #endif |
| #if defined(FSMC_BCR1_WFDIS) |
| |
| if (Init->NSBank != FSMC_NORSRAM_BANK1) |
| { |
| /* Configure Write FIFO mode when Write Fifo is enabled for bank2..4 */ |
| SET_BIT(Device->BTCR[FSMC_NORSRAM_BANK1], (uint32_t)(Init->WriteFifo)); |
| } |
| #endif /* FSMC_BCR1_WFDIS */ |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief DeInitialize the FSMC_NORSRAM peripheral |
| * @param Device Pointer to NORSRAM device instance |
| * @param ExDevice Pointer to NORSRAM extended mode device instance |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NORSRAM_DeInit(FSMC_NORSRAM_TypeDef *Device, |
| FSMC_NORSRAM_EXTENDED_TypeDef *ExDevice, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FSMC_NORSRAM_EXTENDED_DEVICE(ExDevice)); |
| assert_param(IS_FSMC_NORSRAM_BANK(Bank)); |
| |
| /* Disable the FSMC_NORSRAM device */ |
| __FSMC_NORSRAM_DISABLE(Device, Bank); |
| |
| /* De-initialize the FSMC_NORSRAM device */ |
| /* FSMC_NORSRAM_BANK1 */ |
| if (Bank == FSMC_NORSRAM_BANK1) |
| { |
| Device->BTCR[Bank] = 0x000030DBU; |
| } |
| /* FSMC_NORSRAM_BANK2, FSMC_NORSRAM_BANK3 or FSMC_NORSRAM_BANK4 */ |
| else |
| { |
| Device->BTCR[Bank] = 0x000030D2U; |
| } |
| |
| Device->BTCR[Bank + 1U] = 0x0FFFFFFFU; |
| ExDevice->BWTR[Bank] = 0x0FFFFFFFU; |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initialize the FSMC_NORSRAM Timing according to the specified |
| * parameters in the FSMC_NORSRAM_TimingTypeDef |
| * @param Device Pointer to NORSRAM device instance |
| * @param Timing Pointer to NORSRAM Timing structure |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NORSRAM_Timing_Init(FSMC_NORSRAM_TypeDef *Device, |
| FSMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank) |
| { |
| #if defined(FSMC_BCR1_CCLKEN) |
| uint32_t tmpr; |
| #endif |
| |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FSMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime)); |
| assert_param(IS_FSMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime)); |
| assert_param(IS_FSMC_DATASETUP_TIME(Timing->DataSetupTime)); |
| assert_param(IS_FSMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration)); |
| assert_param(IS_FSMC_CLK_DIV(Timing->CLKDivision)); |
| assert_param(IS_FSMC_DATA_LATENCY(Timing->DataLatency)); |
| assert_param(IS_FSMC_ACCESS_MODE(Timing->AccessMode)); |
| assert_param(IS_FSMC_NORSRAM_BANK(Bank)); |
| |
| /* Set FSMC_NORSRAM device timing parameters */ |
| MODIFY_REG(Device->BTCR[Bank + 1U], BTR_CLEAR_MASK, (Timing->AddressSetupTime | |
| ((Timing->AddressHoldTime) << FSMC_BTR1_ADDHLD_Pos) | |
| ((Timing->DataSetupTime) << FSMC_BTR1_DATAST_Pos) | |
| ((Timing->BusTurnAroundDuration) << FSMC_BTR1_BUSTURN_Pos) | |
| (((Timing->CLKDivision) - 1U) << FSMC_BTR1_CLKDIV_Pos) | |
| (((Timing->DataLatency) - 2U) << FSMC_BTR1_DATLAT_Pos) | |
| (Timing->AccessMode))); |
| |
| #if defined(FSMC_BCR1_CCLKEN) |
| /* Configure Clock division value (in NORSRAM bank 1) when continuous clock is enabled */ |
| if (HAL_IS_BIT_SET(Device->BTCR[FSMC_NORSRAM_BANK1], FSMC_BCR1_CCLKEN)) |
| { |
| tmpr = (uint32_t)(Device->BTCR[FSMC_NORSRAM_BANK1 + 1U] & ~((0x0FU) << FSMC_BTR1_CLKDIV_Pos)); |
| tmpr |= (uint32_t)(((Timing->CLKDivision) - 1U) << FSMC_BTR1_CLKDIV_Pos); |
| MODIFY_REG(Device->BTCR[FSMC_NORSRAM_BANK1 + 1U], FSMC_BTR1_CLKDIV, tmpr); |
| } |
| |
| #endif |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initialize the FSMC_NORSRAM Extended mode Timing according to the specified |
| * parameters in the FSMC_NORSRAM_TimingTypeDef |
| * @param Device Pointer to NORSRAM device instance |
| * @param Timing Pointer to NORSRAM Timing structure |
| * @param Bank NORSRAM bank number |
| * @param ExtendedMode FSMC Extended Mode |
| * This parameter can be one of the following values: |
| * @arg FSMC_EXTENDED_MODE_DISABLE |
| * @arg FSMC_EXTENDED_MODE_ENABLE |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NORSRAM_Extended_Timing_Init(FSMC_NORSRAM_EXTENDED_TypeDef *Device, |
| FSMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank, |
| uint32_t ExtendedMode) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_EXTENDED_MODE(ExtendedMode)); |
| |
| /* Set NORSRAM device timing register for write configuration, if extended mode is used */ |
| if (ExtendedMode == FSMC_EXTENDED_MODE_ENABLE) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NORSRAM_EXTENDED_DEVICE(Device)); |
| assert_param(IS_FSMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime)); |
| assert_param(IS_FSMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime)); |
| assert_param(IS_FSMC_DATASETUP_TIME(Timing->DataSetupTime)); |
| assert_param(IS_FSMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration)); |
| assert_param(IS_FSMC_ACCESS_MODE(Timing->AccessMode)); |
| assert_param(IS_FSMC_NORSRAM_BANK(Bank)); |
| |
| /* Set NORSRAM device timing register for write configuration, if extended mode is used */ |
| MODIFY_REG(Device->BWTR[Bank], BWTR_CLEAR_MASK, (Timing->AddressSetupTime | |
| ((Timing->AddressHoldTime) << FSMC_BWTR1_ADDHLD_Pos) | |
| ((Timing->DataSetupTime) << FSMC_BWTR1_DATAST_Pos) | |
| Timing->AccessMode | |
| ((Timing->BusTurnAroundDuration) << FSMC_BWTR1_BUSTURN_Pos))); |
| } |
| else |
| { |
| Device->BWTR[Bank] = 0x0FFFFFFFU; |
| } |
| |
| return HAL_OK; |
| } |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup FSMC_LL_NORSRAM_Private_Functions_Group2 |
| * @brief management functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### FSMC_NORSRAM Control functions ##### |
| ============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to control dynamically |
| the FSMC NORSRAM interface. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Enables dynamically FSMC_NORSRAM write operation. |
| * @param Device Pointer to NORSRAM device instance |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NORSRAM_WriteOperation_Enable(FSMC_NORSRAM_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FSMC_NORSRAM_BANK(Bank)); |
| |
| /* Enable write operation */ |
| SET_BIT(Device->BTCR[Bank], FSMC_WRITE_OPERATION_ENABLE); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Disables dynamically FSMC_NORSRAM write operation. |
| * @param Device Pointer to NORSRAM device instance |
| * @param Bank NORSRAM bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NORSRAM_WriteOperation_Disable(FSMC_NORSRAM_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NORSRAM_DEVICE(Device)); |
| assert_param(IS_FSMC_NORSRAM_BANK(Bank)); |
| |
| /* Disable write operation */ |
| CLEAR_BIT(Device->BTCR[Bank], FSMC_WRITE_OPERATION_ENABLE); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| #endif /* FSMC_Bank1 */ |
| |
| #if defined(FSMC_Bank2_3) |
| |
| /** @defgroup FSMC_LL_Exported_Functions_NAND FSMC Low Layer NAND Exported Functions |
| * @brief NAND Controller functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use NAND device driver ##### |
| ============================================================================== |
| [..] |
| This driver contains a set of APIs to interface with the FSMC NAND banks in order |
| to run the NAND external devices. |
| |
| (+) FSMC NAND bank reset using the function FSMC_NAND_DeInit() |
| (+) FSMC NAND bank control configuration using the function FSMC_NAND_Init() |
| (+) FSMC NAND bank common space timing configuration using the function |
| FSMC_NAND_CommonSpace_Timing_Init() |
| (+) FSMC NAND bank attribute space timing configuration using the function |
| FSMC_NAND_AttributeSpace_Timing_Init() |
| (+) FSMC NAND bank enable/disable ECC correction feature using the functions |
| FSMC_NAND_ECC_Enable()/FSMC_NAND_ECC_Disable() |
| (+) FSMC NAND bank get ECC correction code using the function FSMC_NAND_GetECC() |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** @defgroup FSMC_LL_NAND_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de_initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to: |
| (+) Initialize and configure the FSMC NAND interface |
| (+) De-initialize the FSMC NAND interface |
| (+) Configure the FSMC clock and associated GPIOs |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the FSMC_NAND device according to the specified |
| * control parameters in the FSMC_NAND_HandleTypeDef |
| * @param Device Pointer to NAND device instance |
| * @param Init Pointer to NAND Initialization structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_Init(FSMC_NAND_TypeDef *Device, FSMC_NAND_InitTypeDef *Init) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_NAND_BANK(Init->NandBank)); |
| assert_param(IS_FSMC_WAIT_FEATURE(Init->Waitfeature)); |
| assert_param(IS_FSMC_NAND_MEMORY_WIDTH(Init->MemoryDataWidth)); |
| assert_param(IS_FSMC_ECC_STATE(Init->EccComputation)); |
| assert_param(IS_FSMC_ECCPAGE_SIZE(Init->ECCPageSize)); |
| assert_param(IS_FSMC_TCLR_TIME(Init->TCLRSetupTime)); |
| assert_param(IS_FSMC_TAR_TIME(Init->TARSetupTime)); |
| |
| /* Set NAND device control parameters */ |
| if (Init->NandBank == FSMC_NAND_BANK2) |
| { |
| /* NAND bank 2 registers configuration */ |
| MODIFY_REG(Device->PCR2, PCR_CLEAR_MASK, (Init->Waitfeature | |
| FSMC_PCR_MEMORY_TYPE_NAND | |
| Init->MemoryDataWidth | |
| Init->EccComputation | |
| Init->ECCPageSize | |
| ((Init->TCLRSetupTime) << FSMC_PCR2_TCLR_Pos) | |
| ((Init->TARSetupTime) << FSMC_PCR2_TAR_Pos))); |
| } |
| else |
| { |
| /* NAND bank 3 registers configuration */ |
| MODIFY_REG(Device->PCR3, PCR_CLEAR_MASK, (Init->Waitfeature | |
| FSMC_PCR_MEMORY_TYPE_NAND | |
| Init->MemoryDataWidth | |
| Init->EccComputation | |
| Init->ECCPageSize | |
| ((Init->TCLRSetupTime) << FSMC_PCR2_TCLR_Pos) | |
| ((Init->TARSetupTime) << FSMC_PCR2_TAR_Pos))); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FSMC_NAND Common space Timing according to the specified |
| * parameters in the FSMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to NAND device instance |
| * @param Timing Pointer to NAND timing structure |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_CommonSpace_Timing_Init(FSMC_NAND_TypeDef *Device, |
| FSMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime)); |
| assert_param(IS_FSMC_NAND_BANK(Bank)); |
| |
| /* Set FSMC_NAND device timing parameters */ |
| if (Bank == FSMC_NAND_BANK2) |
| { |
| /* NAND bank 2 registers configuration */ |
| MODIFY_REG(Device->PMEM2, PMEM_CLEAR_MASK, (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << FSMC_PMEM2_MEMWAIT2_Pos) | |
| ((Timing->HoldSetupTime) << FSMC_PMEM2_MEMHOLD2_Pos) | |
| ((Timing->HiZSetupTime) << FSMC_PMEM2_MEMHIZ2_Pos))); |
| } |
| else |
| { |
| /* NAND bank 3 registers configuration */ |
| MODIFY_REG(Device->PMEM3, PMEM_CLEAR_MASK, (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << FSMC_PMEM2_MEMWAIT2_Pos) | |
| ((Timing->HoldSetupTime) << FSMC_PMEM2_MEMHOLD2_Pos) | |
| ((Timing->HiZSetupTime) << FSMC_PMEM2_MEMHIZ2_Pos))); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FSMC_NAND Attribute space Timing according to the specified |
| * parameters in the FSMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to NAND device instance |
| * @param Timing Pointer to NAND timing structure |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_AttributeSpace_Timing_Init(FSMC_NAND_TypeDef *Device, |
| FSMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime)); |
| assert_param(IS_FSMC_NAND_BANK(Bank)); |
| |
| /* Set FSMC_NAND device timing parameters */ |
| if (Bank == FSMC_NAND_BANK2) |
| { |
| /* NAND bank 2 registers configuration */ |
| MODIFY_REG(Device->PATT2, PATT_CLEAR_MASK, (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << FSMC_PATT2_ATTWAIT2_Pos) | |
| ((Timing->HoldSetupTime) << FSMC_PATT2_ATTHOLD2_Pos) | |
| ((Timing->HiZSetupTime) << FSMC_PATT2_ATTHIZ2_Pos))); |
| } |
| else |
| { |
| /* NAND bank 3 registers configuration */ |
| MODIFY_REG(Device->PATT3, PATT_CLEAR_MASK, (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << FSMC_PATT2_ATTWAIT2_Pos) | |
| ((Timing->HoldSetupTime) << FSMC_PATT2_ATTHOLD2_Pos) | |
| ((Timing->HiZSetupTime) << FSMC_PATT2_ATTHIZ2_Pos))); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief DeInitializes the FSMC_NAND device |
| * @param Device Pointer to NAND device instance |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_DeInit(FSMC_NAND_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_NAND_BANK(Bank)); |
| |
| /* Disable the NAND Bank */ |
| __FSMC_NAND_DISABLE(Device, Bank); |
| |
| /* De-initialize the NAND Bank */ |
| if (Bank == FSMC_NAND_BANK2) |
| { |
| /* Set the FSMC_NAND_BANK2 registers to their reset values */ |
| WRITE_REG(Device->PCR2, 0x00000018U); |
| WRITE_REG(Device->SR2, 0x00000040U); |
| WRITE_REG(Device->PMEM2, 0xFCFCFCFCU); |
| WRITE_REG(Device->PATT2, 0xFCFCFCFCU); |
| } |
| /* FSMC_Bank3_NAND */ |
| else |
| { |
| /* Set the FSMC_NAND_BANK3 registers to their reset values */ |
| WRITE_REG(Device->PCR3, 0x00000018U); |
| WRITE_REG(Device->SR3, 0x00000040U); |
| WRITE_REG(Device->PMEM3, 0xFCFCFCFCU); |
| WRITE_REG(Device->PATT3, 0xFCFCFCFCU); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup HAL_FSMC_NAND_Group2 Peripheral Control functions |
| * @brief management functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### FSMC_NAND Control functions ##### |
| ============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to control dynamically |
| the FSMC NAND interface. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| |
| /** |
| * @brief Enables dynamically FSMC_NAND ECC feature. |
| * @param Device Pointer to NAND device instance |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_ECC_Enable(FSMC_NAND_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_NAND_BANK(Bank)); |
| |
| /* Enable ECC feature */ |
| if (Bank == FSMC_NAND_BANK2) |
| { |
| SET_BIT(Device->PCR2, FSMC_PCR2_ECCEN); |
| } |
| else |
| { |
| SET_BIT(Device->PCR3, FSMC_PCR2_ECCEN); |
| } |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief Disables dynamically FSMC_NAND ECC feature. |
| * @param Device Pointer to NAND device instance |
| * @param Bank NAND bank number |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_ECC_Disable(FSMC_NAND_TypeDef *Device, uint32_t Bank) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_NAND_BANK(Bank)); |
| |
| /* Disable ECC feature */ |
| if (Bank == FSMC_NAND_BANK2) |
| { |
| CLEAR_BIT(Device->PCR2, FSMC_PCR2_ECCEN); |
| } |
| else |
| { |
| CLEAR_BIT(Device->PCR3, FSMC_PCR2_ECCEN); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Disables dynamically FSMC_NAND ECC feature. |
| * @param Device Pointer to NAND device instance |
| * @param ECCval Pointer to ECC value |
| * @param Bank NAND bank number |
| * @param Timeout Timeout wait value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_NAND_GetECC(FSMC_NAND_TypeDef *Device, uint32_t *ECCval, uint32_t Bank, |
| uint32_t Timeout) |
| { |
| uint32_t tickstart; |
| |
| /* Check the parameters */ |
| assert_param(IS_FSMC_NAND_DEVICE(Device)); |
| assert_param(IS_FSMC_NAND_BANK(Bank)); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait until FIFO is empty */ |
| while (__FSMC_NAND_GET_FLAG(Device, Bank, FSMC_FLAG_FEMPT) == RESET) |
| { |
| /* Check for the Timeout */ |
| if (Timeout != HAL_MAX_DELAY) |
| { |
| if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) |
| { |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| if (Bank == FSMC_NAND_BANK2) |
| { |
| /* Get the ECCR2 register value */ |
| *ECCval = (uint32_t)Device->ECCR2; |
| } |
| else |
| { |
| /* Get the ECCR3 register value */ |
| *ECCval = (uint32_t)Device->ECCR3; |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| #endif /* FSMC_Bank2_3 */ |
| |
| #if defined(FSMC_Bank4) |
| |
| /** @addtogroup FSMC_LL_PCCARD |
| * @brief PCCARD Controller functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use PCCARD device driver ##### |
| ============================================================================== |
| [..] |
| This driver contains a set of APIs to interface with the FSMC PCCARD bank in order |
| to run the PCCARD/compact flash external devices. |
| |
| (+) FSMC PCCARD bank reset using the function FSMC_PCCARD_DeInit() |
| (+) FSMC PCCARD bank control configuration using the function FSMC_PCCARD_Init() |
| (+) FSMC PCCARD bank common space timing configuration using the function |
| FSMC_PCCARD_CommonSpace_Timing_Init() |
| (+) FSMC PCCARD bank attribute space timing configuration using the function |
| FSMC_PCCARD_AttributeSpace_Timing_Init() |
| (+) FSMC PCCARD bank IO space timing configuration using the function |
| FSMC_PCCARD_IOSpace_Timing_Init() |
| @endverbatim |
| * @{ |
| */ |
| |
| /** @addtogroup FSMC_LL_PCCARD_Private_Functions_Group1 |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de_initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to: |
| (+) Initialize and configure the FSMC PCCARD interface |
| (+) De-initialize the FSMC PCCARD interface |
| (+) Configure the FSMC clock and associated GPIOs |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the FSMC_PCCARD device according to the specified |
| * control parameters in the FSMC_PCCARD_HandleTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Init Pointer to PCCARD Initialization structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_PCCARD_Init(FSMC_PCCARD_TypeDef *Device, FSMC_PCCARD_InitTypeDef *Init) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_PCCARD_DEVICE(Device)); |
| #if defined(FSMC_Bank2_3) |
| assert_param(IS_FSMC_WAIT_FEATURE(Init->Waitfeature)); |
| assert_param(IS_FSMC_TCLR_TIME(Init->TCLRSetupTime)); |
| assert_param(IS_FSMC_TAR_TIME(Init->TARSetupTime)); |
| #endif /* FSMC_Bank2_3 */ |
| |
| /* Set FSMC_PCCARD device control parameters */ |
| MODIFY_REG(Device->PCR4, |
| (FSMC_PCR4_PTYP | |
| FSMC_PCR4_PWAITEN | |
| FSMC_PCR4_PWID | |
| FSMC_PCR4_TCLR | |
| FSMC_PCR4_TAR), |
| (FSMC_PCR_MEMORY_TYPE_PCCARD | |
| Init->Waitfeature | |
| FSMC_NAND_PCC_MEM_BUS_WIDTH_16 | |
| (Init->TCLRSetupTime << FSMC_PCR4_TCLR_Pos) | |
| (Init->TARSetupTime << FSMC_PCR4_TAR_Pos))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FSMC_PCCARD Common space Timing according to the specified |
| * parameters in the FSMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Timing Pointer to PCCARD timing structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_PCCARD_CommonSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device, |
| FSMC_NAND_PCC_TimingTypeDef *Timing) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_PCCARD_DEVICE(Device)); |
| #if defined(FSMC_Bank2_3) |
| assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime)); |
| #endif /* FSMC_Bank2_3 */ |
| |
| /* Set PCCARD timing parameters */ |
| MODIFY_REG(Device->PMEM4, PMEM4_CLEAR_MASK, |
| (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << FSMC_PMEM4_MEMWAIT4_Pos) | |
| ((Timing->HoldSetupTime) << FSMC_PMEM4_MEMHOLD4_Pos) | |
| ((Timing->HiZSetupTime) << FSMC_PMEM4_MEMHIZ4_Pos))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FSMC_PCCARD Attribute space Timing according to the specified |
| * parameters in the FSMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Timing Pointer to PCCARD timing structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_PCCARD_AttributeSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device, |
| FSMC_NAND_PCC_TimingTypeDef *Timing) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_PCCARD_DEVICE(Device)); |
| #if defined(FSMC_Bank2_3) |
| assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime)); |
| #endif /* FSMC_Bank2_3 */ |
| |
| /* Set PCCARD timing parameters */ |
| MODIFY_REG(Device->PATT4, PATT4_CLEAR_MASK, |
| (Timing->SetupTime | |
| ((Timing->WaitSetupTime) << FSMC_PATT4_ATTWAIT4_Pos) | |
| ((Timing->HoldSetupTime) << FSMC_PATT4_ATTHOLD4_Pos) | |
| ((Timing->HiZSetupTime) << FSMC_PATT4_ATTHIZ4_Pos))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the FSMC_PCCARD IO space Timing according to the specified |
| * parameters in the FSMC_NAND_PCC_TimingTypeDef |
| * @param Device Pointer to PCCARD device instance |
| * @param Timing Pointer to PCCARD timing structure |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_PCCARD_IOSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device, |
| FSMC_NAND_PCC_TimingTypeDef *Timing) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_PCCARD_DEVICE(Device)); |
| #if defined(FSMC_Bank2_3) |
| assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime)); |
| assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime)); |
| assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime)); |
| assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime)); |
| #endif /* FSMC_Bank2_3 */ |
| |
| /* Set FSMC_PCCARD device timing parameters */ |
| MODIFY_REG(Device->PIO4, PIO4_CLEAR_MASK, |
| (Timing->SetupTime | |
| (Timing->WaitSetupTime << FSMC_PIO4_IOWAIT4_Pos) | |
| (Timing->HoldSetupTime << FSMC_PIO4_IOHOLD4_Pos) | |
| (Timing->HiZSetupTime << FSMC_PIO4_IOHIZ4_Pos))); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief DeInitializes the FSMC_PCCARD device |
| * @param Device Pointer to PCCARD device instance |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef FSMC_PCCARD_DeInit(FSMC_PCCARD_TypeDef *Device) |
| { |
| /* Check the parameters */ |
| assert_param(IS_FSMC_PCCARD_DEVICE(Device)); |
| |
| /* Disable the FSMC_PCCARD device */ |
| __FSMC_PCCARD_DISABLE(Device); |
| |
| /* De-initialize the FSMC_PCCARD device */ |
| Device->PCR4 = 0x00000018U; |
| Device->SR4 = 0x00000040U; |
| Device->PMEM4 = 0xFCFCFCFCU; |
| Device->PATT4 = 0xFCFCFCFCU; |
| Device->PIO4 = 0xFCFCFCFCU; |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| #endif /* FSMC_Bank4 */ |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* HAL_NOR_MODULE_ENABLED */ |
| /** |
| * @} |
| */ |
| /** |
| * @} |
| */ |
