| /** |
| ****************************************************************************** |
| * @file stm32f4xx_ll_sdmmc.h |
| * @author MCD Application Team |
| * @brief Header file of SDMMC HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef __STM32F4xx_LL_SDMMC_H |
| #define __STM32F4xx_LL_SDMMC_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| #if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ |
| defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ |
| defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ |
| defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ |
| defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx) |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f4xx_hal_def.h" |
| |
| /** @addtogroup STM32F4xx_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup SDMMC_LL |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup SDMMC_LL_Exported_Types SDMMC_LL Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief SDMMC Configuration Structure definition |
| */ |
| typedef struct |
| { |
| uint32_t ClockEdge; /*!< Specifies the clock transition on which the bit capture is made. |
| This parameter can be a value of @ref SDMMC_LL_Clock_Edge */ |
| |
| uint32_t ClockBypass; /*!< Specifies whether the SDMMC Clock divider bypass is |
| enabled or disabled. |
| This parameter can be a value of @ref SDMMC_LL_Clock_Bypass */ |
| |
| uint32_t ClockPowerSave; /*!< Specifies whether SDMMC Clock output is enabled or |
| disabled when the bus is idle. |
| This parameter can be a value of @ref SDMMC_LL_Clock_Power_Save */ |
| |
| uint32_t BusWide; /*!< Specifies the SDMMC bus width. |
| This parameter can be a value of @ref SDMMC_LL_Bus_Wide */ |
| |
| uint32_t HardwareFlowControl; /*!< Specifies whether the SDMMC hardware flow control is enabled or disabled. |
| This parameter can be a value of @ref SDMMC_LL_Hardware_Flow_Control */ |
| |
| uint32_t ClockDiv; /*!< Specifies the clock frequency of the SDMMC controller. |
| This parameter can be a value between Min_Data = 0 and Max_Data = 255 */ |
| |
| }SDIO_InitTypeDef; |
| |
| |
| /** |
| * @brief SDMMC Command Control structure |
| */ |
| typedef struct |
| { |
| uint32_t Argument; /*!< Specifies the SDMMC command argument which is sent |
| to a card as part of a command message. If a command |
| contains an argument, it must be loaded into this register |
| before writing the command to the command register. */ |
| |
| uint32_t CmdIndex; /*!< Specifies the SDMMC command index. It must be Min_Data = 0 and |
| Max_Data = 64 */ |
| |
| uint32_t Response; /*!< Specifies the SDMMC response type. |
| This parameter can be a value of @ref SDMMC_LL_Response_Type */ |
| |
| uint32_t WaitForInterrupt; /*!< Specifies whether SDMMC wait for interrupt request is |
| enabled or disabled. |
| This parameter can be a value of @ref SDMMC_LL_Wait_Interrupt_State */ |
| |
| uint32_t CPSM; /*!< Specifies whether SDMMC Command path state machine (CPSM) |
| is enabled or disabled. |
| This parameter can be a value of @ref SDMMC_LL_CPSM_State */ |
| }SDIO_CmdInitTypeDef; |
| |
| |
| /** |
| * @brief SDMMC Data Control structure |
| */ |
| typedef struct |
| { |
| uint32_t DataTimeOut; /*!< Specifies the data timeout period in card bus clock periods. */ |
| |
| uint32_t DataLength; /*!< Specifies the number of data bytes to be transferred. */ |
| |
| uint32_t DataBlockSize; /*!< Specifies the data block size for block transfer. |
| This parameter can be a value of @ref SDMMC_LL_Data_Block_Size */ |
| |
| uint32_t TransferDir; /*!< Specifies the data transfer direction, whether the transfer |
| is a read or write. |
| This parameter can be a value of @ref SDMMC_LL_Transfer_Direction */ |
| |
| uint32_t TransferMode; /*!< Specifies whether data transfer is in stream or block mode. |
| This parameter can be a value of @ref SDMMC_LL_Transfer_Type */ |
| |
| uint32_t DPSM; /*!< Specifies whether SDMMC Data path state machine (DPSM) |
| is enabled or disabled. |
| This parameter can be a value of @ref SDMMC_LL_DPSM_State */ |
| }SDIO_DataInitTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup SDMMC_LL_Exported_Constants SDMMC_LL Exported Constants |
| * @{ |
| */ |
| #define SDMMC_ERROR_NONE 0x00000000U /*!< No error */ |
| #define SDMMC_ERROR_CMD_CRC_FAIL 0x00000001U /*!< Command response received (but CRC check failed) */ |
| #define SDMMC_ERROR_DATA_CRC_FAIL 0x00000002U /*!< Data block sent/received (CRC check failed) */ |
| #define SDMMC_ERROR_CMD_RSP_TIMEOUT 0x00000004U /*!< Command response timeout */ |
| #define SDMMC_ERROR_DATA_TIMEOUT 0x00000008U /*!< Data timeout */ |
| #define SDMMC_ERROR_TX_UNDERRUN 0x00000010U /*!< Transmit FIFO underrun */ |
| #define SDMMC_ERROR_RX_OVERRUN 0x00000020U /*!< Receive FIFO overrun */ |
| #define SDMMC_ERROR_ADDR_MISALIGNED 0x00000040U /*!< Misaligned address */ |
| #define SDMMC_ERROR_BLOCK_LEN_ERR 0x00000080U /*!< Transferred block length is not allowed for the card or the |
| number of transferred bytes does not match the block length */ |
| #define SDMMC_ERROR_ERASE_SEQ_ERR 0x00000100U /*!< An error in the sequence of erase command occurs */ |
| #define SDMMC_ERROR_BAD_ERASE_PARAM 0x00000200U /*!< An invalid selection for erase groups */ |
| #define SDMMC_ERROR_WRITE_PROT_VIOLATION 0x00000400U /*!< Attempt to program a write protect block */ |
| #define SDMMC_ERROR_LOCK_UNLOCK_FAILED 0x00000800U /*!< Sequence or password error has been detected in unlock |
| command or if there was an attempt to access a locked card */ |
| #define SDMMC_ERROR_COM_CRC_FAILED 0x00001000U /*!< CRC check of the previous command failed */ |
| #define SDMMC_ERROR_ILLEGAL_CMD 0x00002000U /*!< Command is not legal for the card state */ |
| #define SDMMC_ERROR_CARD_ECC_FAILED 0x00004000U /*!< Card internal ECC was applied but failed to correct the data */ |
| #define SDMMC_ERROR_CC_ERR 0x00008000U /*!< Internal card controller error */ |
| #define SDMMC_ERROR_GENERAL_UNKNOWN_ERR 0x00010000U /*!< General or unknown error */ |
| #define SDMMC_ERROR_STREAM_READ_UNDERRUN 0x00020000U /*!< The card could not sustain data reading in stream rmode */ |
| #define SDMMC_ERROR_STREAM_WRITE_OVERRUN 0x00040000U /*!< The card could not sustain data programming in stream mode */ |
| #define SDMMC_ERROR_CID_CSD_OVERWRITE 0x00080000U /*!< CID/CSD overwrite error */ |
| #define SDMMC_ERROR_WP_ERASE_SKIP 0x00100000U /*!< Only partial address space was erased */ |
| #define SDMMC_ERROR_CARD_ECC_DISABLED 0x00200000U /*!< Command has been executed without using internal ECC */ |
| #define SDMMC_ERROR_ERASE_RESET 0x00400000U /*!< Erase sequence was cleared before executing because an out |
| of erase sequence command was received */ |
| #define SDMMC_ERROR_AKE_SEQ_ERR 0x00800000U /*!< Error in sequence of authentication */ |
| #define SDMMC_ERROR_INVALID_VOLTRANGE 0x01000000U /*!< Error in case of invalid voltage range */ |
| #define SDMMC_ERROR_ADDR_OUT_OF_RANGE 0x02000000U /*!< Error when addressed block is out of range */ |
| #define SDMMC_ERROR_REQUEST_NOT_APPLICABLE 0x04000000U /*!< Error when command request is not applicable */ |
| #define SDMMC_ERROR_INVALID_PARAMETER 0x08000000U /*!< the used parameter is not valid */ |
| #define SDMMC_ERROR_UNSUPPORTED_FEATURE 0x10000000U /*!< Error when feature is not insupported */ |
| #define SDMMC_ERROR_BUSY 0x20000000U /*!< Error when transfer process is busy */ |
| #define SDMMC_ERROR_DMA 0x40000000U /*!< Error while DMA transfer */ |
| #define SDMMC_ERROR_TIMEOUT 0x80000000U /*!< Timeout error */ |
| |
| /** |
| * @brief SDMMC Commands Index |
| */ |
| #define SDMMC_CMD_GO_IDLE_STATE ((uint8_t)0) /*!< Resets the SD memory card. */ |
| #define SDMMC_CMD_SEND_OP_COND ((uint8_t)1) /*!< Sends host capacity support information and activates the card's initialization process. */ |
| #define SDMMC_CMD_ALL_SEND_CID ((uint8_t)2) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */ |
| #define SDMMC_CMD_SET_REL_ADDR ((uint8_t)3) /*!< Asks the card to publish a new relative address (RCA). */ |
| #define SDMMC_CMD_SET_DSR ((uint8_t)4) /*!< Programs the DSR of all cards. */ |
| #define SDMMC_CMD_SDMMC_SEN_OP_COND ((uint8_t)5) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its |
| operating condition register (OCR) content in the response on the CMD line. */ |
| #define SDMMC_CMD_HS_SWITCH ((uint8_t)6) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */ |
| #define SDMMC_CMD_SEL_DESEL_CARD ((uint8_t)7) /*!< Selects the card by its own relative address and gets deselected by any other address */ |
| #define SDMMC_CMD_HS_SEND_EXT_CSD ((uint8_t)8) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information |
| and asks the card whether card supports voltage. */ |
| #define SDMMC_CMD_SEND_CSD ((uint8_t)9) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */ |
| #define SDMMC_CMD_SEND_CID ((uint8_t)10) /*!< Addressed card sends its card identification (CID) on the CMD line. */ |
| #define SDMMC_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11) /*!< SD card doesn't support it. */ |
| #define SDMMC_CMD_STOP_TRANSMISSION ((uint8_t)12) /*!< Forces the card to stop transmission. */ |
| #define SDMMC_CMD_SEND_STATUS ((uint8_t)13) /*!< Addressed card sends its status register. */ |
| #define SDMMC_CMD_HS_BUSTEST_READ ((uint8_t)14) /*!< Reserved */ |
| #define SDMMC_CMD_GO_INACTIVE_STATE ((uint8_t)15) /*!< Sends an addressed card into the inactive state. */ |
| #define SDMMC_CMD_SET_BLOCKLEN ((uint8_t)16) /*!< Sets the block length (in bytes for SDSC) for all following block commands |
| (read, write, lock). Default block length is fixed to 512 Bytes. Not effective |
| for SDHS and SDXC. */ |
| #define SDMMC_CMD_READ_SINGLE_BLOCK ((uint8_t)17) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of |
| fixed 512 bytes in case of SDHC and SDXC. */ |
| #define SDMMC_CMD_READ_MULT_BLOCK ((uint8_t)18) /*!< Continuously transfers data blocks from card to host until interrupted by |
| STOP_TRANSMISSION command. */ |
| #define SDMMC_CMD_HS_BUSTEST_WRITE ((uint8_t)19) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */ |
| #define SDMMC_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20) /*!< Speed class control command. */ |
| #define SDMMC_CMD_SET_BLOCK_COUNT ((uint8_t)23) /*!< Specify block count for CMD18 and CMD25. */ |
| #define SDMMC_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of |
| fixed 512 bytes in case of SDHC and SDXC. */ |
| #define SDMMC_CMD_WRITE_MULT_BLOCK ((uint8_t)25) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */ |
| #define SDMMC_CMD_PROG_CID ((uint8_t)26) /*!< Reserved for manufacturers. */ |
| #define SDMMC_CMD_PROG_CSD ((uint8_t)27) /*!< Programming of the programmable bits of the CSD. */ |
| #define SDMMC_CMD_SET_WRITE_PROT ((uint8_t)28) /*!< Sets the write protection bit of the addressed group. */ |
| #define SDMMC_CMD_CLR_WRITE_PROT ((uint8_t)29) /*!< Clears the write protection bit of the addressed group. */ |
| #define SDMMC_CMD_SEND_WRITE_PROT ((uint8_t)30) /*!< Asks the card to send the status of the write protection bits. */ |
| #define SDMMC_CMD_SD_ERASE_GRP_START ((uint8_t)32) /*!< Sets the address of the first write block to be erased. (For SD card only). */ |
| #define SDMMC_CMD_SD_ERASE_GRP_END ((uint8_t)33) /*!< Sets the address of the last write block of the continuous range to be erased. */ |
| #define SDMMC_CMD_ERASE_GRP_START ((uint8_t)35) /*!< Sets the address of the first write block to be erased. Reserved for each command |
| system set by switch function command (CMD6). */ |
| #define SDMMC_CMD_ERASE_GRP_END ((uint8_t)36) /*!< Sets the address of the last write block of the continuous range to be erased. |
| Reserved for each command system set by switch function command (CMD6). */ |
| #define SDMMC_CMD_ERASE ((uint8_t)38) /*!< Reserved for SD security applications. */ |
| #define SDMMC_CMD_FAST_IO ((uint8_t)39) /*!< SD card doesn't support it (Reserved). */ |
| #define SDMMC_CMD_GO_IRQ_STATE ((uint8_t)40) /*!< SD card doesn't support it (Reserved). */ |
| #define SDMMC_CMD_LOCK_UNLOCK ((uint8_t)42) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by |
| the SET_BLOCK_LEN command. */ |
| #define SDMMC_CMD_APP_CMD ((uint8_t)55) /*!< Indicates to the card that the next command is an application specific command rather |
| than a standard command. */ |
| #define SDMMC_CMD_GEN_CMD ((uint8_t)56) /*!< Used either to transfer a data block to the card or to get a data block from the card |
| for general purpose/application specific commands. */ |
| #define SDMMC_CMD_NO_CMD ((uint8_t)64) /*!< No command */ |
| |
| /** |
| * @brief Following commands are SD Card Specific commands. |
| * SDMMC_APP_CMD should be sent before sending these commands. |
| */ |
| #define SDMMC_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus |
| widths are given in SCR register. */ |
| #define SDMMC_CMD_SD_APP_STATUS ((uint8_t)13) /*!< (ACMD13) Sends the SD status. */ |
| #define SDMMC_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with |
| 32bit+CRC data block. */ |
| #define SDMMC_CMD_SD_APP_OP_COND ((uint8_t)41) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to |
| send its operating condition register (OCR) content in the response on the CMD line. */ |
| #define SDMMC_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42) /*!< (ACMD42) Connect/Disconnect the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card */ |
| #define SDMMC_CMD_SD_APP_SEND_SCR ((uint8_t)51) /*!< Reads the SD Configuration Register (SCR). */ |
| #define SDMMC_CMD_SDMMC_RW_DIRECT ((uint8_t)52) /*!< For SD I/O card only, reserved for security specification. */ |
| #define SDMMC_CMD_SDMMC_RW_EXTENDED ((uint8_t)53) /*!< For SD I/O card only, reserved for security specification. */ |
| |
| /** |
| * @brief Following commands are SD Card Specific security commands. |
| * SDMMC_CMD_APP_CMD should be sent before sending these commands. |
| */ |
| #define SDMMC_CMD_SD_APP_GET_MKB ((uint8_t)43) |
| #define SDMMC_CMD_SD_APP_GET_MID ((uint8_t)44) |
| #define SDMMC_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45) |
| #define SDMMC_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46) |
| #define SDMMC_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47) |
| #define SDMMC_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48) |
| #define SDMMC_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18) |
| #define SDMMC_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25) |
| #define SDMMC_CMD_SD_APP_SECURE_ERASE ((uint8_t)38) |
| #define SDMMC_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49) |
| #define SDMMC_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48) |
| |
| /** |
| * @brief Masks for errors Card Status R1 (OCR Register) |
| */ |
| #define SDMMC_OCR_ADDR_OUT_OF_RANGE 0x80000000U |
| #define SDMMC_OCR_ADDR_MISALIGNED 0x40000000U |
| #define SDMMC_OCR_BLOCK_LEN_ERR 0x20000000U |
| #define SDMMC_OCR_ERASE_SEQ_ERR 0x10000000U |
| #define SDMMC_OCR_BAD_ERASE_PARAM 0x08000000U |
| #define SDMMC_OCR_WRITE_PROT_VIOLATION 0x04000000U |
| #define SDMMC_OCR_LOCK_UNLOCK_FAILED 0x01000000U |
| #define SDMMC_OCR_COM_CRC_FAILED 0x00800000U |
| #define SDMMC_OCR_ILLEGAL_CMD 0x00400000U |
| #define SDMMC_OCR_CARD_ECC_FAILED 0x00200000U |
| #define SDMMC_OCR_CC_ERROR 0x00100000U |
| #define SDMMC_OCR_GENERAL_UNKNOWN_ERROR 0x00080000U |
| #define SDMMC_OCR_STREAM_READ_UNDERRUN 0x00040000U |
| #define SDMMC_OCR_STREAM_WRITE_OVERRUN 0x00020000U |
| #define SDMMC_OCR_CID_CSD_OVERWRITE 0x00010000U |
| #define SDMMC_OCR_WP_ERASE_SKIP 0x00008000U |
| #define SDMMC_OCR_CARD_ECC_DISABLED 0x00004000U |
| #define SDMMC_OCR_ERASE_RESET 0x00002000U |
| #define SDMMC_OCR_AKE_SEQ_ERROR 0x00000008U |
| #define SDMMC_OCR_ERRORBITS 0xFDFFE008U |
| |
| /** |
| * @brief Masks for R6 Response |
| */ |
| #define SDMMC_R6_GENERAL_UNKNOWN_ERROR 0x00002000U |
| #define SDMMC_R6_ILLEGAL_CMD 0x00004000U |
| #define SDMMC_R6_COM_CRC_FAILED 0x00008000U |
| |
| #define SDMMC_VOLTAGE_WINDOW_SD 0x80100000U |
| #define SDMMC_HIGH_CAPACITY 0x40000000U |
| #define SDMMC_STD_CAPACITY 0x00000000U |
| #define SDMMC_CHECK_PATTERN 0x000001AAU |
| |
| #define SDMMC_MAX_VOLT_TRIAL 0x0000FFFFU |
| |
| #define SDMMC_MAX_TRIAL 0x0000FFFFU |
| |
| #define SDMMC_ALLZERO 0x00000000U |
| |
| #define SDMMC_WIDE_BUS_SUPPORT 0x00040000U |
| #define SDMMC_SINGLE_BUS_SUPPORT 0x00010000U |
| #define SDMMC_CARD_LOCKED 0x02000000U |
| |
| #define SDMMC_DATATIMEOUT 0xFFFFFFFFU |
| |
| #define SDMMC_0TO7BITS 0x000000FFU |
| #define SDMMC_8TO15BITS 0x0000FF00U |
| #define SDMMC_16TO23BITS 0x00FF0000U |
| #define SDMMC_24TO31BITS 0xFF000000U |
| #define SDMMC_MAX_DATA_LENGTH 0x01FFFFFFU |
| |
| #define SDMMC_HALFFIFO 0x00000008U |
| #define SDMMC_HALFFIFOBYTES 0x00000020U |
| |
| /** |
| * @brief Command Class supported |
| */ |
| #define SDIO_CCCC_ERASE 0x00000020U |
| |
| #define SDIO_CMDTIMEOUT 5000U /* Command send and response timeout */ |
| #define SDIO_MAXERASETIMEOUT 63000U /* Max erase Timeout 63 s */ |
| |
| |
| /** @defgroup SDIO_LL_Clock_Edge Clock Edge |
| * @{ |
| */ |
| #define SDIO_CLOCK_EDGE_RISING 0x00000000U |
| #define SDIO_CLOCK_EDGE_FALLING SDIO_CLKCR_NEGEDGE |
| |
| #define IS_SDIO_CLOCK_EDGE(EDGE) (((EDGE) == SDIO_CLOCK_EDGE_RISING) || \ |
| ((EDGE) == SDIO_CLOCK_EDGE_FALLING)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Clock_Bypass Clock Bypass |
| * @{ |
| */ |
| #define SDIO_CLOCK_BYPASS_DISABLE 0x00000000U |
| #define SDIO_CLOCK_BYPASS_ENABLE SDIO_CLKCR_BYPASS |
| |
| #define IS_SDIO_CLOCK_BYPASS(BYPASS) (((BYPASS) == SDIO_CLOCK_BYPASS_DISABLE) || \ |
| ((BYPASS) == SDIO_CLOCK_BYPASS_ENABLE)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Clock_Power_Save Clock Power Saving |
| * @{ |
| */ |
| #define SDIO_CLOCK_POWER_SAVE_DISABLE 0x00000000U |
| #define SDIO_CLOCK_POWER_SAVE_ENABLE SDIO_CLKCR_PWRSAV |
| |
| #define IS_SDIO_CLOCK_POWER_SAVE(SAVE) (((SAVE) == SDIO_CLOCK_POWER_SAVE_DISABLE) || \ |
| ((SAVE) == SDIO_CLOCK_POWER_SAVE_ENABLE)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Bus_Wide Bus Width |
| * @{ |
| */ |
| #define SDIO_BUS_WIDE_1B 0x00000000U |
| #define SDIO_BUS_WIDE_4B SDIO_CLKCR_WIDBUS_0 |
| #define SDIO_BUS_WIDE_8B SDIO_CLKCR_WIDBUS_1 |
| |
| #define IS_SDIO_BUS_WIDE(WIDE) (((WIDE) == SDIO_BUS_WIDE_1B) || \ |
| ((WIDE) == SDIO_BUS_WIDE_4B) || \ |
| ((WIDE) == SDIO_BUS_WIDE_8B)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Hardware_Flow_Control Hardware Flow Control |
| * @{ |
| */ |
| #define SDIO_HARDWARE_FLOW_CONTROL_DISABLE 0x00000000U |
| #define SDIO_HARDWARE_FLOW_CONTROL_ENABLE SDIO_CLKCR_HWFC_EN |
| |
| #define IS_SDIO_HARDWARE_FLOW_CONTROL(CONTROL) (((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_DISABLE) || \ |
| ((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_ENABLE)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Clock_Division Clock Division |
| * @{ |
| */ |
| #define IS_SDIO_CLKDIV(DIV) ((DIV) <= 0xFFU) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Command_Index Command Index |
| * @{ |
| */ |
| #define IS_SDIO_CMD_INDEX(INDEX) ((INDEX) < 0x40U) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Response_Type Response Type |
| * @{ |
| */ |
| #define SDIO_RESPONSE_NO 0x00000000U |
| #define SDIO_RESPONSE_SHORT SDIO_CMD_WAITRESP_0 |
| #define SDIO_RESPONSE_LONG SDIO_CMD_WAITRESP |
| |
| #define IS_SDIO_RESPONSE(RESPONSE) (((RESPONSE) == SDIO_RESPONSE_NO) || \ |
| ((RESPONSE) == SDIO_RESPONSE_SHORT) || \ |
| ((RESPONSE) == SDIO_RESPONSE_LONG)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Wait_Interrupt_State Wait Interrupt |
| * @{ |
| */ |
| #define SDIO_WAIT_NO 0x00000000U |
| #define SDIO_WAIT_IT SDIO_CMD_WAITINT |
| #define SDIO_WAIT_PEND SDIO_CMD_WAITPEND |
| |
| #define IS_SDIO_WAIT(WAIT) (((WAIT) == SDIO_WAIT_NO) || \ |
| ((WAIT) == SDIO_WAIT_IT) || \ |
| ((WAIT) == SDIO_WAIT_PEND)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_CPSM_State CPSM State |
| * @{ |
| */ |
| #define SDIO_CPSM_DISABLE 0x00000000U |
| #define SDIO_CPSM_ENABLE SDIO_CMD_CPSMEN |
| |
| #define IS_SDIO_CPSM(CPSM) (((CPSM) == SDIO_CPSM_DISABLE) || \ |
| ((CPSM) == SDIO_CPSM_ENABLE)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Response_Registers Response Register |
| * @{ |
| */ |
| #define SDIO_RESP1 0x00000000U |
| #define SDIO_RESP2 0x00000004U |
| #define SDIO_RESP3 0x00000008U |
| #define SDIO_RESP4 0x0000000CU |
| |
| #define IS_SDIO_RESP(RESP) (((RESP) == SDIO_RESP1) || \ |
| ((RESP) == SDIO_RESP2) || \ |
| ((RESP) == SDIO_RESP3) || \ |
| ((RESP) == SDIO_RESP4)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Data_Length Data Lenght |
| * @{ |
| */ |
| #define IS_SDIO_DATA_LENGTH(LENGTH) ((LENGTH) <= 0x01FFFFFFU) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Data_Block_Size Data Block Size |
| * @{ |
| */ |
| #define SDIO_DATABLOCK_SIZE_1B 0x00000000U |
| #define SDIO_DATABLOCK_SIZE_2B SDIO_DCTRL_DBLOCKSIZE_0 |
| #define SDIO_DATABLOCK_SIZE_4B SDIO_DCTRL_DBLOCKSIZE_1 |
| #define SDIO_DATABLOCK_SIZE_8B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1) |
| #define SDIO_DATABLOCK_SIZE_16B SDIO_DCTRL_DBLOCKSIZE_2 |
| #define SDIO_DATABLOCK_SIZE_32B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2) |
| #define SDIO_DATABLOCK_SIZE_64B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2) |
| #define SDIO_DATABLOCK_SIZE_128B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2) |
| #define SDIO_DATABLOCK_SIZE_256B SDIO_DCTRL_DBLOCKSIZE_3 |
| #define SDIO_DATABLOCK_SIZE_512B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_3) |
| #define SDIO_DATABLOCK_SIZE_1024B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3) |
| #define SDIO_DATABLOCK_SIZE_2048B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3) |
| #define SDIO_DATABLOCK_SIZE_4096B (SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) |
| #define SDIO_DATABLOCK_SIZE_8192B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) |
| #define SDIO_DATABLOCK_SIZE_16384B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) |
| |
| #define IS_SDIO_BLOCK_SIZE(SIZE) (((SIZE) == SDIO_DATABLOCK_SIZE_1B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_2B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_4B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_8B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_16B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_32B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_64B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_128B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_256B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_512B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_1024B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_2048B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_4096B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_8192B) || \ |
| ((SIZE) == SDIO_DATABLOCK_SIZE_16384B)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Transfer_Direction Transfer Direction |
| * @{ |
| */ |
| #define SDIO_TRANSFER_DIR_TO_CARD 0x00000000U |
| #define SDIO_TRANSFER_DIR_TO_SDIO SDIO_DCTRL_DTDIR |
| |
| #define IS_SDIO_TRANSFER_DIR(DIR) (((DIR) == SDIO_TRANSFER_DIR_TO_CARD) || \ |
| ((DIR) == SDIO_TRANSFER_DIR_TO_SDIO)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Transfer_Type Transfer Type |
| * @{ |
| */ |
| #define SDIO_TRANSFER_MODE_BLOCK 0x00000000U |
| #define SDIO_TRANSFER_MODE_STREAM SDIO_DCTRL_DTMODE |
| |
| #define IS_SDIO_TRANSFER_MODE(MODE) (((MODE) == SDIO_TRANSFER_MODE_BLOCK) || \ |
| ((MODE) == SDIO_TRANSFER_MODE_STREAM)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_DPSM_State DPSM State |
| * @{ |
| */ |
| #define SDIO_DPSM_DISABLE 0x00000000U |
| #define SDIO_DPSM_ENABLE SDIO_DCTRL_DTEN |
| |
| #define IS_SDIO_DPSM(DPSM) (((DPSM) == SDIO_DPSM_DISABLE) ||\ |
| ((DPSM) == SDIO_DPSM_ENABLE)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Read_Wait_Mode Read Wait Mode |
| * @{ |
| */ |
| #define SDIO_READ_WAIT_MODE_DATA2 0x00000000U |
| #define SDIO_READ_WAIT_MODE_CLK (SDIO_DCTRL_RWMOD) |
| |
| #define IS_SDIO_READWAIT_MODE(MODE) (((MODE) == SDIO_READ_WAIT_MODE_CLK) || \ |
| ((MODE) == SDIO_READ_WAIT_MODE_DATA2)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Interrupt_sources Interrupt Sources |
| * @{ |
| */ |
| #define SDIO_IT_CCRCFAIL SDIO_STA_CCRCFAIL |
| #define SDIO_IT_DCRCFAIL SDIO_STA_DCRCFAIL |
| #define SDIO_IT_CTIMEOUT SDIO_STA_CTIMEOUT |
| #define SDIO_IT_DTIMEOUT SDIO_STA_DTIMEOUT |
| #define SDIO_IT_TXUNDERR SDIO_STA_TXUNDERR |
| #define SDIO_IT_RXOVERR SDIO_STA_RXOVERR |
| #define SDIO_IT_CMDREND SDIO_STA_CMDREND |
| #define SDIO_IT_CMDSENT SDIO_STA_CMDSENT |
| #define SDIO_IT_DATAEND SDIO_STA_DATAEND |
| #define SDIO_IT_STBITERR SDIO_STA_STBITERR |
| #define SDIO_IT_DBCKEND SDIO_STA_DBCKEND |
| #define SDIO_IT_CMDACT SDIO_STA_CMDACT |
| #define SDIO_IT_TXACT SDIO_STA_TXACT |
| #define SDIO_IT_RXACT SDIO_STA_RXACT |
| #define SDIO_IT_TXFIFOHE SDIO_STA_TXFIFOHE |
| #define SDIO_IT_RXFIFOHF SDIO_STA_RXFIFOHF |
| #define SDIO_IT_TXFIFOF SDIO_STA_TXFIFOF |
| #define SDIO_IT_RXFIFOF SDIO_STA_RXFIFOF |
| #define SDIO_IT_TXFIFOE SDIO_STA_TXFIFOE |
| #define SDIO_IT_RXFIFOE SDIO_STA_RXFIFOE |
| #define SDIO_IT_TXDAVL SDIO_STA_TXDAVL |
| #define SDIO_IT_RXDAVL SDIO_STA_RXDAVL |
| #define SDIO_IT_SDIOIT SDIO_STA_SDIOIT |
| #define SDIO_IT_CEATAEND SDIO_STA_CEATAEND |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Flags Flags |
| * @{ |
| */ |
| #define SDIO_FLAG_CCRCFAIL SDIO_STA_CCRCFAIL |
| #define SDIO_FLAG_DCRCFAIL SDIO_STA_DCRCFAIL |
| #define SDIO_FLAG_CTIMEOUT SDIO_STA_CTIMEOUT |
| #define SDIO_FLAG_DTIMEOUT SDIO_STA_DTIMEOUT |
| #define SDIO_FLAG_TXUNDERR SDIO_STA_TXUNDERR |
| #define SDIO_FLAG_RXOVERR SDIO_STA_RXOVERR |
| #define SDIO_FLAG_CMDREND SDIO_STA_CMDREND |
| #define SDIO_FLAG_CMDSENT SDIO_STA_CMDSENT |
| #define SDIO_FLAG_DATAEND SDIO_STA_DATAEND |
| #define SDIO_FLAG_STBITERR SDIO_STA_STBITERR |
| #define SDIO_FLAG_DBCKEND SDIO_STA_DBCKEND |
| #define SDIO_FLAG_CMDACT SDIO_STA_CMDACT |
| #define SDIO_FLAG_TXACT SDIO_STA_TXACT |
| #define SDIO_FLAG_RXACT SDIO_STA_RXACT |
| #define SDIO_FLAG_TXFIFOHE SDIO_STA_TXFIFOHE |
| #define SDIO_FLAG_RXFIFOHF SDIO_STA_RXFIFOHF |
| #define SDIO_FLAG_TXFIFOF SDIO_STA_TXFIFOF |
| #define SDIO_FLAG_RXFIFOF SDIO_STA_RXFIFOF |
| #define SDIO_FLAG_TXFIFOE SDIO_STA_TXFIFOE |
| #define SDIO_FLAG_RXFIFOE SDIO_STA_RXFIFOE |
| #define SDIO_FLAG_TXDAVL SDIO_STA_TXDAVL |
| #define SDIO_FLAG_RXDAVL SDIO_STA_RXDAVL |
| #define SDIO_FLAG_SDIOIT SDIO_STA_SDIOIT |
| #define SDIO_FLAG_CEATAEND SDIO_STA_CEATAEND |
| #define SDIO_STATIC_FLAGS ((uint32_t)(SDIO_FLAG_CCRCFAIL | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_CTIMEOUT |\ |
| SDIO_FLAG_DTIMEOUT | SDIO_FLAG_TXUNDERR | SDIO_FLAG_RXOVERR |\ |
| SDIO_FLAG_CMDREND | SDIO_FLAG_CMDSENT | SDIO_FLAG_DATAEND |\ |
| SDIO_FLAG_DBCKEND)) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| /** @defgroup SDIO_LL_Exported_macros SDIO_LL Exported Macros |
| * @{ |
| */ |
| |
| /** @defgroup SDMMC_LL_Alias_Region Bit Address in the alias region |
| * @{ |
| */ |
| /* ------------ SDIO registers bit address in the alias region -------------- */ |
| #define SDIO_OFFSET (SDIO_BASE - PERIPH_BASE) |
| |
| /* --- CLKCR Register ---*/ |
| /* Alias word address of CLKEN bit */ |
| #define CLKCR_OFFSET (SDIO_OFFSET + 0x04U) |
| #define CLKEN_BITNUMBER 0x08U |
| #define CLKCR_CLKEN_BB (PERIPH_BB_BASE + (CLKCR_OFFSET * 32U) + (CLKEN_BITNUMBER * 4U)) |
| |
| /* --- CMD Register ---*/ |
| /* Alias word address of SDIOSUSPEND bit */ |
| #define CMD_OFFSET (SDIO_OFFSET + 0x0CU) |
| #define SDIOSUSPEND_BITNUMBER 0x0BU |
| #define CMD_SDIOSUSPEND_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (SDIOSUSPEND_BITNUMBER * 4U)) |
| |
| /* Alias word address of ENCMDCOMPL bit */ |
| #define ENCMDCOMPL_BITNUMBER 0x0CU |
| #define CMD_ENCMDCOMPL_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ENCMDCOMPL_BITNUMBER * 4U)) |
| |
| /* Alias word address of NIEN bit */ |
| #define NIEN_BITNUMBER 0x0DU |
| #define CMD_NIEN_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (NIEN_BITNUMBER * 4U)) |
| |
| /* Alias word address of ATACMD bit */ |
| #define ATACMD_BITNUMBER 0x0EU |
| #define CMD_ATACMD_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ATACMD_BITNUMBER * 4U)) |
| |
| /* --- DCTRL Register ---*/ |
| /* Alias word address of DMAEN bit */ |
| #define DCTRL_OFFSET (SDIO_OFFSET + 0x2CU) |
| #define DMAEN_BITNUMBER 0x03U |
| #define DCTRL_DMAEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (DMAEN_BITNUMBER * 4U)) |
| |
| /* Alias word address of RWSTART bit */ |
| #define RWSTART_BITNUMBER 0x08U |
| #define DCTRL_RWSTART_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTART_BITNUMBER * 4U)) |
| |
| /* Alias word address of RWSTOP bit */ |
| #define RWSTOP_BITNUMBER 0x09U |
| #define DCTRL_RWSTOP_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTOP_BITNUMBER * 4U)) |
| |
| /* Alias word address of RWMOD bit */ |
| #define RWMOD_BITNUMBER 0x0AU |
| #define DCTRL_RWMOD_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWMOD_BITNUMBER * 4U)) |
| |
| /* Alias word address of SDIOEN bit */ |
| #define SDIOEN_BITNUMBER 0x0BU |
| #define DCTRL_SDIOEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (SDIOEN_BITNUMBER * 4U)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Register Bits And Addresses Definitions |
| * @brief SDIO_LL registers bit address in the alias region |
| * @{ |
| */ |
| /* ---------------------- SDIO registers bit mask --------------------------- */ |
| /* --- CLKCR Register ---*/ |
| /* CLKCR register clear mask */ |
| #define CLKCR_CLEAR_MASK ((uint32_t)(SDIO_CLKCR_CLKDIV | SDIO_CLKCR_PWRSAV |\ |
| SDIO_CLKCR_BYPASS | SDIO_CLKCR_WIDBUS |\ |
| SDIO_CLKCR_NEGEDGE | SDIO_CLKCR_HWFC_EN)) |
| |
| /* --- DCTRL Register ---*/ |
| /* SDIO DCTRL Clear Mask */ |
| #define DCTRL_CLEAR_MASK ((uint32_t)(SDIO_DCTRL_DTEN | SDIO_DCTRL_DTDIR |\ |
| SDIO_DCTRL_DTMODE | SDIO_DCTRL_DBLOCKSIZE)) |
| |
| /* --- CMD Register ---*/ |
| /* CMD Register clear mask */ |
| #define CMD_CLEAR_MASK ((uint32_t)(SDIO_CMD_CMDINDEX | SDIO_CMD_WAITRESP |\ |
| SDIO_CMD_WAITINT | SDIO_CMD_WAITPEND |\ |
| SDIO_CMD_CPSMEN | SDIO_CMD_SDIOSUSPEND)) |
| |
| /* SDIO Initialization Frequency (400KHz max) */ |
| #define SDIO_INIT_CLK_DIV ((uint8_t)0x76) |
| |
| /* SDIO Data Transfer Frequency (25MHz max) */ |
| #define SDIO_TRANSFER_CLK_DIV ((uint8_t)0x0) |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SDIO_LL_Interrupt_Clock Interrupt And Clock Configuration |
| * @brief macros to handle interrupts and specific clock configurations |
| * @{ |
| */ |
| |
| /** |
| * @brief Enable the SDIO device. |
| * @param __INSTANCE__ SDIO Instance |
| * @retval None |
| */ |
| #define __SDIO_ENABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = ENABLE) |
| |
| /** |
| * @brief Disable the SDIO device. |
| * @param __INSTANCE__ SDIO Instance |
| * @retval None |
| */ |
| #define __SDIO_DISABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = DISABLE) |
| |
| /** |
| * @brief Enable the SDIO DMA transfer. |
| * @param __INSTANCE__ SDIO Instance |
| * @retval None |
| */ |
| #define __SDIO_DMA_ENABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = ENABLE) |
| /** |
| * @brief Disable the SDIO DMA transfer. |
| * @param __INSTANCE__ SDIO Instance |
| * @retval None |
| */ |
| #define __SDIO_DMA_DISABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = DISABLE) |
| |
| /** |
| * @brief Enable the SDIO device interrupt. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @param __INTERRUPT__ specifies the SDIO interrupt sources to be enabled. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt |
| * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt |
| * @arg SDIO_IT_TXACT: Data transmit in progress interrupt |
| * @arg SDIO_IT_RXACT: Data receive in progress interrupt |
| * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt |
| * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt |
| * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt |
| * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt |
| * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt |
| * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt |
| * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt |
| * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt |
| * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt |
| * @retval None |
| */ |
| #define __SDIO_ENABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK |= (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the SDIO device interrupt. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @param __INTERRUPT__ specifies the SDIO interrupt sources to be disabled. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt |
| * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt |
| * @arg SDIO_IT_TXACT: Data transmit in progress interrupt |
| * @arg SDIO_IT_RXACT: Data receive in progress interrupt |
| * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt |
| * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt |
| * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt |
| * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt |
| * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt |
| * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt |
| * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt |
| * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt |
| * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt |
| * @retval None |
| */ |
| #define __SDIO_DISABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK &= ~(__INTERRUPT__)) |
| |
| /** |
| * @brief Checks whether the specified SDIO flag is set or not. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @param __FLAG__ specifies the flag to check. |
| * This parameter can be one of the following values: |
| * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) |
| * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) |
| * @arg SDIO_FLAG_CTIMEOUT: Command response timeout |
| * @arg SDIO_FLAG_DTIMEOUT: Data timeout |
| * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error |
| * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error |
| * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) |
| * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) |
| * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) |
| * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) |
| * @arg SDIO_FLAG_CMDACT: Command transfer in progress |
| * @arg SDIO_FLAG_TXACT: Data transmit in progress |
| * @arg SDIO_FLAG_RXACT: Data receive in progress |
| * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty |
| * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full |
| * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full |
| * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full |
| * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty |
| * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty |
| * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO |
| * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO |
| * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received |
| * @retval The new state of SDIO_FLAG (SET or RESET). |
| */ |
| #define __SDIO_GET_FLAG(__INSTANCE__, __FLAG__) (((__INSTANCE__)->STA &(__FLAG__)) != RESET) |
| |
| |
| /** |
| * @brief Clears the SDIO pending flags. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @param __FLAG__ specifies the flag to clear. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) |
| * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) |
| * @arg SDIO_FLAG_CTIMEOUT: Command response timeout |
| * @arg SDIO_FLAG_DTIMEOUT: Data timeout |
| * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error |
| * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error |
| * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) |
| * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) |
| * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) |
| * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) |
| * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received |
| * @retval None |
| */ |
| #define __SDIO_CLEAR_FLAG(__INSTANCE__, __FLAG__) ((__INSTANCE__)->ICR = (__FLAG__)) |
| |
| /** |
| * @brief Checks whether the specified SDIO interrupt has occurred or not. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @param __INTERRUPT__ specifies the SDIO interrupt source to check. |
| * This parameter can be one of the following values: |
| * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt |
| * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt |
| * @arg SDIO_IT_TXACT: Data transmit in progress interrupt |
| * @arg SDIO_IT_RXACT: Data receive in progress interrupt |
| * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt |
| * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt |
| * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt |
| * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt |
| * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt |
| * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt |
| * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt |
| * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt |
| * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt |
| * @retval The new state of SDIO_IT (SET or RESET). |
| */ |
| #define __SDIO_GET_IT (__INSTANCE__, __INTERRUPT__) (((__INSTANCE__)->STA &(__INTERRUPT__)) == (__INTERRUPT__)) |
| |
| /** |
| * @brief Clears the SDIO's interrupt pending bits. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @param __INTERRUPT__ specifies the interrupt pending bit to clear. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDIO_IT_DATAEND: Data end (data counter, SDIO_DCOUNT, is zero) interrupt |
| * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt |
| * @retval None |
| */ |
| #define __SDIO_CLEAR_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->ICR = (__INTERRUPT__)) |
| |
| /** |
| * @brief Enable Start the SD I/O Read Wait operation. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_START_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = ENABLE) |
| |
| /** |
| * @brief Disable Start the SD I/O Read Wait operations. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_START_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = DISABLE) |
| |
| /** |
| * @brief Enable Start the SD I/O Read Wait operation. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_STOP_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = ENABLE) |
| |
| /** |
| * @brief Disable Stop the SD I/O Read Wait operations. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_STOP_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = DISABLE) |
| |
| /** |
| * @brief Enable the SD I/O Mode Operation. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_OPERATION_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = ENABLE) |
| |
| /** |
| * @brief Disable the SD I/O Mode Operation. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_OPERATION_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = DISABLE) |
| |
| /** |
| * @brief Enable the SD I/O Suspend command sending. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_SUSPEND_CMD_ENABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = ENABLE) |
| |
| /** |
| * @brief Disable the SD I/O Suspend command sending. |
| * @param __INSTANCE__ Pointer to SDIO register base |
| * @retval None |
| */ |
| #define __SDIO_SUSPEND_CMD_DISABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = DISABLE) |
| |
| #if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ |
| defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ |
| defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) |
| /** |
| * @brief Enable the command completion signal. |
| * @retval None |
| */ |
| #define __SDIO_CEATA_CMD_COMPLETION_ENABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = ENABLE) |
| |
| /** |
| * @brief Disable the command completion signal. |
| * @retval None |
| */ |
| #define __SDIO_CEATA_CMD_COMPLETION_DISABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = DISABLE) |
| |
| /** |
| * @brief Enable the CE-ATA interrupt. |
| * @retval None |
| */ |
| #define __SDIO_CEATA_ENABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)0U) |
| |
| /** |
| * @brief Disable the CE-ATA interrupt. |
| * @retval None |
| */ |
| #define __SDIO_CEATA_DISABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)1U) |
| |
| /** |
| * @brief Enable send CE-ATA command (CMD61). |
| * @retval None |
| */ |
| #define __SDIO_CEATA_SENDCMD_ENABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = ENABLE) |
| |
| /** |
| * @brief Disable send CE-ATA command (CMD61). |
| * @retval None |
| */ |
| #define __SDIO_CEATA_SENDCMD_DISABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = DISABLE) |
| #endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE ||\ |
| STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup SDMMC_LL_Exported_Functions |
| * @{ |
| */ |
| |
| /* Initialization/de-initialization functions **********************************/ |
| /** @addtogroup HAL_SDMMC_LL_Group1 |
| * @{ |
| */ |
| HAL_StatusTypeDef SDIO_Init(SDIO_TypeDef *SDIOx, SDIO_InitTypeDef Init); |
| /** |
| * @} |
| */ |
| |
| /* I/O operation functions *****************************************************/ |
| /** @addtogroup HAL_SDMMC_LL_Group2 |
| * @{ |
| */ |
| uint32_t SDIO_ReadFIFO(SDIO_TypeDef *SDIOx); |
| HAL_StatusTypeDef SDIO_WriteFIFO(SDIO_TypeDef *SDIOx, uint32_t *pWriteData); |
| /** |
| * @} |
| */ |
| |
| /* Peripheral Control functions ************************************************/ |
| /** @addtogroup HAL_SDMMC_LL_Group3 |
| * @{ |
| */ |
| HAL_StatusTypeDef SDIO_PowerState_ON(SDIO_TypeDef *SDIOx); |
| HAL_StatusTypeDef SDIO_PowerState_OFF(SDIO_TypeDef *SDIOx); |
| uint32_t SDIO_GetPowerState(SDIO_TypeDef *SDIOx); |
| |
| /* Command path state machine (CPSM) management functions */ |
| HAL_StatusTypeDef SDIO_SendCommand(SDIO_TypeDef *SDIOx, SDIO_CmdInitTypeDef *Command); |
| uint8_t SDIO_GetCommandResponse(SDIO_TypeDef *SDIOx); |
| uint32_t SDIO_GetResponse(SDIO_TypeDef *SDIOx, uint32_t Response); |
| |
| /* Data path state machine (DPSM) management functions */ |
| HAL_StatusTypeDef SDIO_ConfigData(SDIO_TypeDef *SDIOx, SDIO_DataInitTypeDef* Data); |
| uint32_t SDIO_GetDataCounter(SDIO_TypeDef *SDIOx); |
| uint32_t SDIO_GetFIFOCount(SDIO_TypeDef *SDIOx); |
| |
| /* SDMMC Cards mode management functions */ |
| HAL_StatusTypeDef SDIO_SetSDMMCReadWaitMode(SDIO_TypeDef *SDIOx, uint32_t SDIO_ReadWaitMode); |
| |
| /* SDMMC Commands management functions */ |
| uint32_t SDMMC_CmdBlockLength(SDIO_TypeDef *SDIOx, uint32_t BlockSize); |
| uint32_t SDMMC_CmdReadSingleBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd); |
| uint32_t SDMMC_CmdReadMultiBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd); |
| uint32_t SDMMC_CmdWriteSingleBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd); |
| uint32_t SDMMC_CmdWriteMultiBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd); |
| uint32_t SDMMC_CmdSDEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd); |
| uint32_t SDMMC_CmdSDEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd); |
| uint32_t SDMMC_CmdErase(SDIO_TypeDef *SDIOx); |
| uint32_t SDMMC_CmdStopTransfer(SDIO_TypeDef *SDIOx); |
| uint32_t SDMMC_CmdSelDesel(SDIO_TypeDef *SDIOx, uint64_t Addr); |
| uint32_t SDMMC_CmdGoIdleState(SDIO_TypeDef *SDIOx); |
| uint32_t SDMMC_CmdOperCond(SDIO_TypeDef *SDIOx); |
| uint32_t SDMMC_CmdAppCommand(SDIO_TypeDef *SDIOx, uint32_t Argument); |
| uint32_t SDMMC_CmdAppOperCommand(SDIO_TypeDef *SDIOx, uint32_t SdType); |
| uint32_t SDMMC_CmdBusWidth(SDIO_TypeDef *SDIOx, uint32_t BusWidth); |
| uint32_t SDMMC_CmdSendSCR(SDIO_TypeDef *SDIOx); |
| uint32_t SDMMC_CmdSendCID(SDIO_TypeDef *SDIOx); |
| uint32_t SDMMC_CmdSendCSD(SDIO_TypeDef *SDIOx, uint32_t Argument); |
| uint32_t SDMMC_CmdSetRelAdd(SDIO_TypeDef *SDIOx, uint16_t *pRCA); |
| uint32_t SDMMC_CmdSendStatus(SDIO_TypeDef *SDIOx, uint32_t Argument); |
| uint32_t SDMMC_CmdStatusRegister(SDIO_TypeDef *SDIOx); |
| |
| uint32_t SDMMC_CmdOpCondition(SDIO_TypeDef *SDIOx, uint32_t Argument); |
| uint32_t SDMMC_CmdSwitch(SDIO_TypeDef *SDIOx, uint32_t Argument); |
| uint32_t SDMMC_CmdEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd); |
| uint32_t SDMMC_CmdEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd); |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || |
| STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || |
| STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* __STM32F4xx_LL_SDMMC_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |