| /** |
| ****************************************************************************** |
| * @file stm32g0xx_hal_pwr.h |
| * @author MCD Application Team |
| * @brief Header file of PWR HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2018 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32G0xx_HAL_PWR_H |
| #define STM32G0xx_HAL_PWR_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32g0xx_hal_def.h" |
| |
| /** @addtogroup STM32G0xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup PWR PWR |
| * @brief PWR HAL module driver |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Types PWR Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Constants PWR Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup PWR_WakeUp_Pins PWR WakeUp pins |
| * @{ |
| */ |
| #define PWR_WAKEUP_PIN1 PWR_CR3_EWUP1 /*!< Wakeup pin 1 (with high level detection) */ |
| #define PWR_WAKEUP_PIN2 PWR_CR3_EWUP2 /*!< Wakeup pin 2 (with high level detection) */ |
| #if defined(PWR_CR3_EWUP3) |
| #define PWR_WAKEUP_PIN3 PWR_CR3_EWUP3 /*!< Wakeup pin 3 (with high level detection) */ |
| #endif /* PWR_CR3_EWUP3 */ |
| #define PWR_WAKEUP_PIN4 PWR_CR3_EWUP4 /*!< Wakeup pin 4 (with high level detection) */ |
| #if defined(PWR_CR3_EWUP5) |
| #define PWR_WAKEUP_PIN5 PWR_CR3_EWUP5 /*!< Wakeup pin 5 (with high level detection) */ |
| #endif /* PWR_CR3_EWUP5 */ |
| #define PWR_WAKEUP_PIN6 PWR_CR3_EWUP6 /*!< Wakeup pin 6 (with high level detection) */ |
| #define PWR_WAKEUP_PIN1_HIGH PWR_CR3_EWUP1 /*!< Wakeup pin 1 (with high level detection) */ |
| #define PWR_WAKEUP_PIN2_HIGH PWR_CR3_EWUP2 /*!< Wakeup pin 2 (with high level detection) */ |
| #if defined(PWR_CR3_EWUP3) |
| #define PWR_WAKEUP_PIN3_HIGH PWR_CR3_EWUP3 /*!< Wakeup pin 3 (with high level detection) */ |
| #endif /* PWR_CR3_EWUP3 */ |
| #define PWR_WAKEUP_PIN4_HIGH PWR_CR3_EWUP4 /*!< Wakeup pin 4 (with high level detection) */ |
| #if defined(PWR_CR3_EWUP5) |
| #define PWR_WAKEUP_PIN5_HIGH PWR_CR3_EWUP5 /*!< Wakeup pin 5 (with high level detection) */ |
| #endif /* PWR_CR3_EWUP5*/ |
| #define PWR_WAKEUP_PIN6_HIGH PWR_CR3_EWUP6 /*!< Wakeup pin 6 (with high level detection) */ |
| #define PWR_WAKEUP_PIN1_LOW ((PWR_CR4_WP1 << PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP1) /*!< Wakeup pin 1 (with low level detection) */ |
| #define PWR_WAKEUP_PIN2_LOW ((PWR_CR4_WP2 << PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP2) /*!< Wakeup pin 2 (with low level detection) */ |
| #if defined(PWR_CR3_EWUP3) |
| #define PWR_WAKEUP_PIN3_LOW ((PWR_CR4_WP3 << PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP3) /*!< Wakeup pin 3 (with low level detection) */ |
| #endif /* PWR_CR3_EWUP3 */ |
| #define PWR_WAKEUP_PIN4_LOW ((PWR_CR4_WP4 << PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP4) /*!< Wakeup pin 4 (with low level detection) */ |
| #if defined(PWR_CR3_EWUP5) |
| #define PWR_WAKEUP_PIN5_LOW ((PWR_CR4_WP5 << PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP5) /*!< Wakeup pin 5 (with low level detection) */ |
| #endif /* PWR_CR3_EWUP5 */ |
| #define PWR_WAKEUP_PIN6_LOW ((PWR_CR4_WP6 << PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP6) /*!< Wakeup pin 6 (with low level detection) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_Low_Power_Mode_Selection PWR Low Power Mode Selection |
| * @{ |
| */ |
| #define PWR_LOWPOWERMODE_STOP0 (0x00000000u) /*!< Stop 0: stop mode with main regulator */ |
| #define PWR_LOWPOWERMODE_STOP1 (PWR_CR1_LPMS_0) /*!< Stop 1: stop mode with low power regulator */ |
| #define PWR_LOWPOWERMODE_STANDBY (PWR_CR1_LPMS_0 | PWR_CR1_LPMS_1) /*!< Standby mode */ |
| #if defined(PWR_SHDW_SUPPORT) |
| #define PWR_LOWPOWERMODE_SHUTDOWN (PWR_CR1_LPMS_2) /*!< Shutdown mode */ |
| #endif /* PWR_SHDW_SUPPORT */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR regulator mode |
| * @{ |
| */ |
| #define PWR_MAINREGULATOR_ON (0x00000000u) /*!< Regulator in main mode */ |
| #define PWR_LOWPOWERREGULATOR_ON PWR_CR1_LPR /*!< Regulator in low-power mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry |
| * @{ |
| */ |
| #define PWR_SLEEPENTRY_WFI ((uint8_t)0x01u) /*!< Wait For Interruption instruction to enter Sleep mode */ |
| #define PWR_SLEEPENTRY_WFE ((uint8_t)0x02u) /*!< Wait For Event instruction to enter Sleep mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_STOP_mode_entry PWR STOP mode entry |
| * @{ |
| */ |
| #define PWR_STOPENTRY_WFI ((uint8_t)0x01u) /*!< Wait For Interruption instruction to enter Stop mode */ |
| #define PWR_STOPENTRY_WFE ((uint8_t)0x02u) /*!< Wait For Event instruction to enter Stop mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_Flag PWR Status Flags |
| * @brief Elements values convention: 0000 00XX 000Y YYYYb |
| * - Y YYYY : Flag position in the XX register (5 bits) |
| * - XX : Status register (2 bits) |
| * - 01: SR1 register |
| * - 10: SR2 register |
| * The only exception is PWR_FLAG_WU, encompassing all |
| * wake-up flags and set to PWR_SR1_WUF. |
| * @{ |
| */ |
| #define PWR_FLAG_WUF1 (0x00010000u | PWR_SR1_WUF1) /*!< Wakeup event on wakeup pin 1 */ |
| #define PWR_FLAG_WUF2 (0x00010000u | PWR_SR1_WUF2) /*!< Wakeup event on wakeup pin 2 */ |
| #if defined(PWR_CR3_EWUP3) |
| #define PWR_FLAG_WUF3 (0x00010000u | PWR_SR1_WUF3) /*!< Wakeup event on wakeup pin 3 */ |
| #endif /* PWR_CR3_EWUP3 */ |
| #define PWR_FLAG_WUF4 (0x00010000u | PWR_SR1_WUF4) /*!< Wakeup event on wakeup pin 4 */ |
| #if defined(PWR_CR3_EWUP5) |
| #define PWR_FLAG_WUF5 (0x00010000u | PWR_SR1_WUF5) /*!< Wakeup event on wakeup pin 5 */ |
| #endif /* PWR_CR3_EWUP5 */ |
| #define PWR_FLAG_WUF6 (0x00010000u | PWR_SR1_WUF6) /*!< Wakeup event on wakeup pin 6 */ |
| #define PWR_FLAG_WUF (0x00010000u | PWR_SR1_WUF) /*!< Wakeup event on all wakeup pin */ |
| #define PWR_FLAG_SB (0x00010000u | PWR_SR1_SBF) /*!< Standby flag */ |
| #define PWR_FLAG_WUFI (0x00010000u | PWR_SR1_WUFI) /*!< Wakeup on internal wakeup line */ |
| #define PWR_FLAG_FLASH_READY (0x00020000u | PWR_SR2_FLASH_RDY) /*!< Flash ready */ |
| #define PWR_FLAG_REGLPS (0x00020000u | PWR_SR2_REGLPS) /*!< Regulator Low Power started */ |
| #define PWR_FLAG_REGLPF (0x00020000u | PWR_SR2_REGLPF) /*!< Regulator Low Power flag */ |
| #if defined(PWR_PVD_SUPPORT) |
| #define PWR_FLAG_PVDO (0x00020000u | PWR_SR2_PVDO) /*!< Power Voltage Detector output */ |
| #endif /* PWR_PVD_SUPPORT */ |
| #if defined(PWR_PVM_SUPPORT) |
| #define PWR_FLAG_PVMO_USB (0x00020000u | PWR_SR2_PVMO_USB) /*!< Power Voltage Monitoring output */ |
| #endif /* PWR_PVM_SUPPORT */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Macros PWR Exported Macros |
| * @{ |
| */ |
| /** @brief Check whether or not a specific PWR flag is set. |
| * @param __FLAG__ specifies the flag to check. |
| * This parameter can be one a combination of following values: |
| * @arg PWR_FLAG_WUF1: Wake Up Flag 1. Indicates that a wakeup event |
| * was received from the WKUP pin 1. |
| * @arg PWR_FLAG_WUF2: Wake Up Flag 2. Indicates that a wakeup event |
| * was received from the WKUP pin 2. |
| * @arg PWR_FLAG_WUF3: Wake Up Flag 3. Indicates that a wakeup event |
| * was received from the WKUP pin 3. (*) |
| * @arg PWR_FLAG_WUF4: Wake Up Flag 4. Indicates that a wakeup event |
| * was received from the WKUP pin 4. |
| * @arg PWR_FLAG_WUF5: Wake Up Flag 5. Indicates that a wakeup event |
| * was received from the WKUP pin 5. (*) |
| * @arg PWR_FLAG_WUF6: Wake Up Flag 6. Indicates that a wakeup event |
| * was received from the WKUP pin 6. |
| * @arg PWR_FLAG_SB: StandBy Flag. Indicates that the system |
| * entered StandBy mode. |
| * @arg PWR_FLAG_WUFI: Wake-Up Flag Internal. Set when a wakeup is |
| * detected on the internal wakeup line. |
| * OR a combination of following values: |
| * @arg PWR_FLAG_FLASH_READY: Flash is ready. Indicates whether flash |
| * can be used or not |
| * @arg PWR_FLAG_REGLPS: Low Power Regulator Started. Indicates whether |
| * or not the low-power regulator is ready. |
| * @arg PWR_FLAG_REGLPF: Low Power Regulator Flag. Indicates whether the |
| * regulator is ready in main mode or is in low-power mode. |
| * @if defined(STM32G081xx) |
| * @arg PWR_FLAG_PVDO: Power Voltage Detector Output. Indicates whether |
| * VDD voltage is below or above the selected PVD threshold. |
| * @endif |
| * @retval The new state of __FLAG__ (TRUE or FALSE). |
| */ |
| #define __HAL_PWR_GET_FLAG(__FLAG__) (((__FLAG__) & 0x00010000u) ?\ |
| ((PWR->SR1 & ((__FLAG__) & ~0x00030000u)) == ((__FLAG__) & ~0x00030000u)) :\ |
| ((PWR->SR2 & ((__FLAG__) & ~0x00030000u)) == ((__FLAG__) & ~0x00030000u))) |
| |
| /** @brief Clear a specific PWR flag. |
| * @param __FLAG__ specifies the flag to clear. |
| * This parameter can be a combination of following values: |
| * @arg PWR_FLAG_WUF1: Wake Up Flag 1. Indicates that a wakeup event |
| * was received from the WKUP pin 1. |
| * @arg PWR_FLAG_WUF2: Wake Up Flag 2. Indicates that a wakeup event |
| * was received from the WKUP pin 2. |
| * @arg PWR_FLAG_WUF3: Wake Up Flag 3. Indicates that a wakeup event |
| * was received from the WKUP pin 3. (*) |
| * @arg PWR_FLAG_WUF4: Wake Up Flag 4. Indicates that a wakeup event |
| * was received from the WKUP pin 4. |
| * @arg PWR_FLAG_WUF5: Wake Up Flag 5. Indicates that a wakeup event |
| * was received from the WKUP pin 5. (*) |
| * @arg PWR_FLAG_WUF6: Wake Up Flag 6. Indicates that a wakeup event |
| * was received from the WKUP pin 6. |
| * @arg PWR_FLAG_WUF: Encompasses all Wake Up Flags. |
| * @arg PWR_FLAG_SB: Standby Flag. Indicates that the system |
| * entered Standby mode. |
| * @retval None |
| */ |
| #define __HAL_PWR_CLEAR_FLAG(__FLAG__) (PWR->SCR = (__FLAG__)) |
| |
| /** |
| * @} |
| */ |
| |
| /* Private constants-------------------------------------------------------*/ |
| /** @defgroup PWR_WUP_Polarity Shift to apply to retrieve polarity information from PWR_WAKEUP_PINy_xxx constants |
| * @{ |
| */ |
| #define PWR_WUP_POLARITY_SHIFT 0x08u /*!< Internal constant used to retrieve wakeup pin polariry */ |
| /** |
| * @} |
| */ |
| |
| /* Private macros --------------------------------------------------------*/ |
| /** @defgroup PWR_Private_Macros PWR Private Macros |
| * @{ |
| */ |
| |
| #define IS_PWR_WAKEUP_PIN(PIN) ((((PIN) & ((PWR_CR4_WP << 8U) | (PWR_CR3_EWUP))) != 0x00000000u) && \ |
| (((PIN) & ~((PWR_CR4_WP << 8U) | (PWR_CR3_EWUP))) == 0x00000000u)) |
| |
| #define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \ |
| ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON)) |
| |
| #define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || \ |
| ((ENTRY) == PWR_SLEEPENTRY_WFE)) |
| |
| #define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || \ |
| ((ENTRY) == PWR_STOPENTRY_WFE)) |
| /** |
| * @} |
| */ |
| |
| /* Include PWR HAL Extended module */ |
| #include "stm32g0xx_hal_pwr_ex.h" |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @defgroup PWR_Exported_Functions PWR Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @{ |
| */ |
| |
| /* Initialization and de-initialization functions *******************************/ |
| void HAL_PWR_DeInit(void); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions |
| * @{ |
| */ |
| /* Peripheral Control functions ************************************************/ |
| void HAL_PWR_EnableBkUpAccess(void); |
| void HAL_PWR_DisableBkUpAccess(void); |
| |
| /* WakeUp pins configuration functions ****************************************/ |
| void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinPolarity); |
| void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx); |
| |
| /* Low Power modes configuration functions ************************************/ |
| void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry); |
| void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry); |
| void HAL_PWR_EnterSTANDBYMode(void); |
| void HAL_PWR_EnableSleepOnExit(void); |
| void HAL_PWR_DisableSleepOnExit(void); |
| void HAL_PWR_EnableSEVOnPend(void); |
| void HAL_PWR_DisableSEVOnPend(void); |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| |
| #endif /* STM32G0xx_HAL_PWR_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
