Src/stm32g4xx_hal.c

/**
  ******************************************************************************
  * @file    stm32g4xx_hal.c
  * @author  MCD Application Team
  * @brief   HAL module driver.
  *          This is the common part of the HAL initialization
  *
  @verbatim
  ==============================================================================
                     ##### How to use this driver #####
  ==============================================================================
    [..]
    The common HAL driver contains a set of generic and common APIs that can be
    used by the PPP peripheral drivers and the user to start using the HAL.
    [..]
    The HAL contains two APIs' categories:
         (+) Common HAL APIs
         (+) Services HAL APIs

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32g4xx_hal.h"

/** @addtogroup STM32G4xx_HAL_Driver
  * @{
  */

/** @defgroup HAL HAL
  * @brief HAL module driver
  * @{
  */

#ifdef HAL_MODULE_ENABLED

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/**
  * @brief STM32G4xx HAL Driver version number V1.2.1
  */
#define __STM32G4xx_HAL_VERSION_MAIN   (0x01U) /*!< [31:24] main version */
#define __STM32G4xx_HAL_VERSION_SUB1   (0x02U) /*!< [23:16] sub1 version */
#define __STM32G4xx_HAL_VERSION_SUB2   (0x01U) /*!< [15:8]  sub2 version */
#define __STM32G4xx_HAL_VERSION_RC     (0x00U) /*!< [7:0]  release candidate */
#define __STM32G4xx_HAL_VERSION         ((__STM32G4xx_HAL_VERSION_MAIN << 24U)\
                                         |(__STM32G4xx_HAL_VERSION_SUB1 << 16U)\
                                         |(__STM32G4xx_HAL_VERSION_SUB2 << 8U )\
                                         |(__STM32G4xx_HAL_VERSION_RC))

#if defined(VREFBUF)
#define VREFBUF_TIMEOUT_VALUE     10U   /* 10 ms */
#endif /* VREFBUF */

/* ------------ SYSCFG registers bit address in the alias region ------------ */
#define SYSCFG_OFFSET             (SYSCFG_BASE - PERIPH_BASE)
/* ---  MEMRMP Register ---*/
/* Alias word address of FB_MODE bit */
#define MEMRMP_OFFSET           SYSCFG_OFFSET
#define FB_MODE_BitNumber       ((uint8_t)0x8)
#define FB_MODE_BB              (PERIPH_BB_BASE + (MEMRMP_OFFSET * 32) + (FB_MODE_BitNumber * 4))

/* --- GPC Register ---*/
/* Alias word address of CCMER bit */
#define SCSR_OFFSET             (SYSCFG_OFFSET + 0x18)
#define CCMER_BitNumber         ((uint8_t)0x0)
#define SCSR_CCMER_BB           (PERIPH_BB_BASE + (SCSR_OFFSET * 32) + (CCMER_BitNumber * 4))

/* Private macro -------------------------------------------------------------*/
/* Exported variables ---------------------------------------------------------*/
/** @defgroup HAL_Exported_Variables HAL Exported Variables
  * @{
  */
__IO uint32_t uwTick;
uint32_t uwTickPrio = (1UL << __NVIC_PRIO_BITS); /* Invalid PRIO */
uint32_t uwTickFreq = HAL_TICK_FREQ_DEFAULT;  /* 1KHz */
/**
  * @}
  */

/* Private function prototypes -----------------------------------------------*/
/* Exported functions --------------------------------------------------------*/

/** @defgroup HAL_Exported_Functions HAL Exported Functions
  * @{
  */

/** @defgroup HAL_Exported_Functions_Group1 Initialization and de-initialization Functions
  *  @brief    HAL Initialization and de-initialization functions
  *
@verbatim
 ===============================================================================
              ##### Initialization and Configuration functions #####
 ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Initialize the Flash interface the NVIC allocation and initial time base
          clock configuration.
      (+) De-Initialize common part of the HAL.
      (+) Configure the time base source to have 1ms time base with a dedicated
          Tick interrupt priority.
        (++) SysTick timer is used by default as source of time base, but user
             can eventually implement his proper time base source (a general purpose
             timer for example or other time source), keeping in mind that Time base
             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
             handled in milliseconds basis.
        (++) Time base configuration function (HAL_InitTick ()) is called automatically
             at the beginning of the program after reset by HAL_Init() or at any time
             when clock is configured, by HAL_RCC_ClockConfig().
        (++) Source of time base is configured  to generate interrupts at regular
             time intervals. Care must be taken if HAL_Delay() is called from a
             peripheral ISR process, the Tick interrupt line must have higher priority
            (numerically lower) than the peripheral interrupt. Otherwise the caller
            ISR process will be blocked.
       (++) functions affecting time base configurations are declared as __weak
             to make  override possible  in case of other  implementations in user file.
@endverbatim
  * @{
  */

/**
  * @brief  This function is used to configure the Flash prefetch, the Instruction and Data caches,
  *         the time base source, NVIC and any required global low level hardware
  *         by calling the HAL_MspInit() callback function to be optionally defined in user file
  *         stm32g4xx_hal_msp.c.
  *
  * @note   HAL_Init() function is called at the beginning of program after reset and before
  *         the clock configuration.
  *
  * @note   In the default implementation the System Timer (Systick) is used as source of time base.
  *         The Systick configuration is based on HSI clock, as HSI is the clock
  *         used after a system Reset and the NVIC configuration is set to Priority group 4.
  *         Once done, time base tick starts incrementing: the tick variable counter is incremented
  *         each 1ms in the SysTick_Handler() interrupt handler.
  *
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_Init(void)
{
  HAL_StatusTypeDef  status = HAL_OK;
  /* Configure Flash prefetch, Instruction cache, Data cache */
  /* Default configuration at reset is:                      */
  /* - Prefetch disabled                                     */
  /* - Instruction cache enabled                             */
  /* - Data cache enabled                                    */
#if (INSTRUCTION_CACHE_ENABLE == 0U)
  __HAL_FLASH_INSTRUCTION_CACHE_DISABLE();
#endif /* INSTRUCTION_CACHE_ENABLE */

#if (DATA_CACHE_ENABLE == 0U)
  __HAL_FLASH_DATA_CACHE_DISABLE();
#endif /* DATA_CACHE_ENABLE */

#if (PREFETCH_ENABLE != 0U)
  __HAL_FLASH_PREFETCH_BUFFER_ENABLE();
#endif /* PREFETCH_ENABLE */

  /* Set Interrupt Group Priority */
  HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);

  /* Use SysTick as time base source and configure 1ms tick (default clock after Reset is HSI) */
  if (HAL_InitTick(TICK_INT_PRIORITY) != HAL_OK)
  {
    status = HAL_ERROR;
  }
  else
  {
    /* Init the low level hardware */
    HAL_MspInit();
  }

  /* Return function status */
  return status;

}

/**
  * @brief  This function de-initializes common part of the HAL and stops the source of time base.
  * @note   This function is optional.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DeInit(void)
{
  /* Reset of all peripherals */
  __HAL_RCC_APB1_FORCE_RESET();
  __HAL_RCC_APB1_RELEASE_RESET();

  __HAL_RCC_APB2_FORCE_RESET();
  __HAL_RCC_APB2_RELEASE_RESET();

  __HAL_RCC_AHB1_FORCE_RESET();
  __HAL_RCC_AHB1_RELEASE_RESET();

  __HAL_RCC_AHB2_FORCE_RESET();
  __HAL_RCC_AHB2_RELEASE_RESET();

  __HAL_RCC_AHB3_FORCE_RESET();
  __HAL_RCC_AHB3_RELEASE_RESET();

  /* De-Init the low level hardware */
  HAL_MspDeInit();

  /* Return function status */
  return HAL_OK;
}

/**
  * @brief  Initialize the MSP.
  * @retval None
  */
__weak void HAL_MspInit(void)
{
  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_MspInit could be implemented in the user file
   */
}

/**
  * @brief  DeInitializes the MSP.
  * @retval None
  */
__weak void HAL_MspDeInit(void)
{
  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_MspDeInit could be implemented in the user file
   */
}

/**
  * @brief This function configures the source of the time base:
  *        The time source is configured to have 1ms time base with a dedicated
  *        Tick interrupt priority.
  * @note This function is called  automatically at the beginning of program after
  *       reset by HAL_Init() or at any time when clock is reconfigured  by HAL_RCC_ClockConfig().
  * @note In the default implementation, SysTick timer is the source of time base.
  *       It is used to generate interrupts at regular time intervals.
  *       Care must be taken if HAL_Delay() is called from a peripheral ISR process,
  *       The SysTick interrupt must have higher priority (numerically lower)
  *       than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
  *       The function is declared as __weak  to be overwritten  in case of other
  *       implementation  in user file.
  * @param TickPriority: Tick interrupt priority.
  * @retval HAL status
  */
__weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority)
{
  HAL_StatusTypeDef  status = HAL_OK;

  if (uwTickFreq != 0U)
  {
    /* Configure the SysTick to have interrupt in 1ms time basis*/
    if (HAL_SYSTICK_Config(SystemCoreClock / (1000U / uwTickFreq)) == 0U)
    {
      /* Configure the SysTick IRQ priority */
      if (TickPriority < (1UL << __NVIC_PRIO_BITS))
      {
        HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U);
        uwTickPrio = TickPriority;
      }
      else
      {
        status = HAL_ERROR;
      }
    }
    else
    {
      status = HAL_ERROR;
    }
  }
  else
  {
    status = HAL_ERROR;
  }

  /* Return function status */
  return status;
}

/**
  * @}
  */

/** @defgroup HAL_Exported_Functions_Group2 HAL Control functions
  *  @brief    HAL Control functions
  *
@verbatim
 ===============================================================================
                      ##### HAL Control functions #####
 ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Provide a tick value in millisecond
      (+) Provide a blocking delay in millisecond
      (+) Suspend the time base source interrupt
      (+) Resume the time base source interrupt
      (+) Get the HAL API driver version
      (+) Get the device identifier
      (+) Get the device revision identifier

@endverbatim
  * @{
  */

/**
  * @brief This function is called to increment a global variable "uwTick"
  *        used as application time base.
  * @note In the default implementation, this variable is incremented each 1ms
  *       in SysTick ISR.
  * @note This function is declared as __weak to be overwritten in case of other
  *      implementations in user file.
  * @retval None
  */
__weak void HAL_IncTick(void)
{
  uwTick += uwTickFreq;
}

/**
  * @brief Provides a tick value in millisecond.
  * @note This function is declared as __weak to be overwritten in case of other
  *       implementations in user file.
  * @retval tick value
  */
__weak uint32_t HAL_GetTick(void)
{
  return uwTick;
}

/**
  * @brief This function returns a tick priority.
  * @retval tick priority
  */
uint32_t HAL_GetTickPrio(void)
{
  return uwTickPrio;
}

/**
  * @brief Set new tick Freq.
  * @retval status
  */
HAL_StatusTypeDef HAL_SetTickFreq(uint32_t Freq)
{
  HAL_StatusTypeDef status  = HAL_OK;
  uint32_t prevTickFreq;

  assert_param(IS_TICKFREQ(Freq));

  if (uwTickFreq != Freq)
  {
    /* Back up uwTickFreq frequency */
    prevTickFreq = uwTickFreq;

    /* Update uwTickFreq global variable used by HAL_InitTick() */
    uwTickFreq = Freq;

    /* Apply the new tick Freq  */
    status = HAL_InitTick(uwTickPrio);

    if (status != HAL_OK)
    {
      /* Restore previous tick frequency */
      uwTickFreq = prevTickFreq;
    }
  }

  return status;
}

/**
  * @brief Returns tick frequency.
  * @retval tick period in Hz
  */
uint32_t HAL_GetTickFreq(void)
{
  return uwTickFreq;
}

/**
  * @brief This function provides minimum delay (in milliseconds) based
  *        on variable incremented.
  * @note In the default implementation , SysTick timer is the source of time base.
  *       It is used to generate interrupts at regular time intervals where uwTick
  *       is incremented.
  * @note This function is declared as __weak to be overwritten in case of other
  *       implementations in user file.
  * @param Delay specifies the delay time length, in milliseconds.
  * @retval None
  */
__weak void HAL_Delay(uint32_t Delay)
{
  uint32_t tickstart = HAL_GetTick();
  uint32_t wait = Delay;

  /* Add a freq to guarantee minimum wait */
  if (wait < HAL_MAX_DELAY)
  {
    wait += (uint32_t)(uwTickFreq);
  }

  while ((HAL_GetTick() - tickstart) < wait)
  {
  }
}

/**
  * @brief Suspends Tick increment.
  * @note In the default implementation , SysTick timer is the source of time base. It is
  *       used to generate interrupts at regular time intervals. Once HAL_SuspendTick()
  *       is called, the SysTick interrupt will be disabled and so Tick increment
  *       is suspended.
  * @note This function is declared as __weak to be overwritten in case of other
  *       implementations in user file.
  * @retval None
  */
__weak void HAL_SuspendTick(void)
{
  /* Disable SysTick Interrupt */
  CLEAR_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk);
}

/**
  * @brief Resume Tick increment.
  * @note In the default implementation , SysTick timer is the source of time base. It is
  *       used to generate interrupts at regular time intervals. Once HAL_ResumeTick()
  *       is called, the SysTick interrupt will be enabled and so Tick increment
  *       is resumed.
  * @note This function is declared as __weak to be overwritten in case of other
  *       implementations in user file.
  * @retval None
  */
__weak void HAL_ResumeTick(void)
{
  /* Enable SysTick Interrupt */
  SET_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk);
}

/**
  * @brief  Returns the HAL revision.
  * @retval version : 0xXYZR (8bits for each decimal, R for RC)
  */
uint32_t HAL_GetHalVersion(void)
{
  return __STM32G4xx_HAL_VERSION;
}

/**
  * @brief  Returns the device revision identifier.
  * @retval Device revision identifier
  */
uint32_t HAL_GetREVID(void)
{
  return ((DBGMCU->IDCODE & DBGMCU_IDCODE_REV_ID) >> 16U);
}

/**
  * @brief  Returns the device identifier.
  * @retval Device identifier
  */
uint32_t HAL_GetDEVID(void)
{
  return (DBGMCU->IDCODE & DBGMCU_IDCODE_DEV_ID);
}

/**
  * @}
  */

/** @defgroup HAL_Exported_Functions_Group3 HAL Debug functions
  *  @brief    HAL Debug functions
  *
@verbatim
 ===============================================================================
                      ##### HAL Debug functions #####
 ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Enable/Disable Debug module during SLEEP mode
      (+) Enable/Disable Debug module during STOP0/STOP1/STOP2 modes
      (+) Enable/Disable Debug module during STANDBY mode

@endverbatim
  * @{
  */

/**
  * @brief  Enable the Debug Module during SLEEP mode.
  * @retval None
  */
void HAL_DBGMCU_EnableDBGSleepMode(void)
{
  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP);
}

/**
  * @brief  Disable the Debug Module during SLEEP mode.
  * @retval None
  */
void HAL_DBGMCU_DisableDBGSleepMode(void)
{
  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP);
}

/**
  * @brief  Enable the Debug Module during STOP0/STOP1/STOP2 modes.
  * @retval None
  */
void HAL_DBGMCU_EnableDBGStopMode(void)
{
  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);
}

/**
  * @brief  Disable the Debug Module during STOP0/STOP1/STOP2 modes.
  * @retval None
  */
void HAL_DBGMCU_DisableDBGStopMode(void)
{
  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);
}

/**
  * @brief  Enable the Debug Module during STANDBY mode.
  * @retval None
  */
void HAL_DBGMCU_EnableDBGStandbyMode(void)
{
  SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
}

/**
  * @brief  Disable the Debug Module during STANDBY mode.
  * @retval None
  */
void HAL_DBGMCU_DisableDBGStandbyMode(void)
{
  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);
}

/**
  * @}
  */

/** @defgroup HAL_Exported_Functions_Group4 HAL SYSCFG configuration functions
  *  @brief    HAL SYSCFG configuration functions
  *
@verbatim
 ===============================================================================
                      ##### HAL SYSCFG configuration functions #####
 ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Start a hardware CCMSRAM erase operation
      (+) Enable/Disable the Internal FLASH Bank Swapping
      (+) Configure the Voltage reference buffer
      (+) Enable/Disable the Voltage reference buffer
      (+) Enable/Disable the I/O analog switch voltage booster

@endverbatim
  * @{
  */

/**
  * @brief  Start a hardware CCMSRAM erase operation.
  * @note   As long as CCMSRAM is not erased the CCMER bit will be set.
  *         This bit is automatically reset at the end of the CCMSRAM erase operation.
  * @retval None
  */
void HAL_SYSCFG_CCMSRAMErase(void)
{
  /* unlock the write protection of the CCMER bit */
  SYSCFG->SKR = 0xCA;
  SYSCFG->SKR = 0x53;
  /* Starts a hardware CCMSRAM erase operation*/
  SET_BIT(SYSCFG->SCSR, SYSCFG_SCSR_CCMER);
}

/**
  * @brief  Enable the Internal FLASH Bank Swapping.
  *
  * @note   This function can be used only for STM32G4xx devices.
  *
  * @note   Flash Bank2 mapped at 0x08000000 (and aliased @0x00000000)
  *         and Flash Bank1 mapped at 0x08040000 (and aliased at 0x00040000)
  *
  * @retval None
  */
void HAL_SYSCFG_EnableMemorySwappingBank(void)
{
  SET_BIT(SYSCFG->MEMRMP, SYSCFG_MEMRMP_FB_MODE);
}

/**
  * @brief  Disable the Internal FLASH Bank Swapping.
  *
  * @note   This function can be used only for STM32G4xx devices.
  *
  * @note   The default state : Flash Bank1 mapped at 0x08000000 (and aliased @0x0000 0000)
  *         and Flash Bank2 mapped at 0x08040000 (and aliased at 0x00040000)
  *
  * @retval None
  */
void HAL_SYSCFG_DisableMemorySwappingBank(void)
{
  CLEAR_BIT(SYSCFG->MEMRMP, SYSCFG_MEMRMP_FB_MODE);
}

#if defined(VREFBUF)
/**
  * @brief Configure the internal voltage reference buffer voltage scale.
  * @param  VoltageScaling: specifies the output voltage to achieve
  *          This parameter can be one of the following values:
  *            @arg SYSCFG_VREFBUF_VOLTAGE_SCALE0: VREFBUF_OUT around 2.048 V.
  *                                                This requires VDDA equal to or higher than 2.4 V.
  *            @arg SYSCFG_VREFBUF_VOLTAGE_SCALE1: VREFBUF_OUT around 2.5 V.
  *                                                This requires VDDA equal to or higher than 2.8 V.
  *            @arg SYSCFG_VREFBUF_VOLTAGE_SCALE2: VREFBUF_OUT around 2.9 V.
  *                                                This requires VDDA equal to or higher than 3.15 V.
  * @retval None
  */
void HAL_SYSCFG_VREFBUF_VoltageScalingConfig(uint32_t VoltageScaling)
{
  /* Check the parameters */
  assert_param(IS_SYSCFG_VREFBUF_VOLTAGE_SCALE(VoltageScaling));

  MODIFY_REG(VREFBUF->CSR, VREFBUF_CSR_VRS, VoltageScaling);
}

/**
  * @brief Configure the internal voltage reference buffer high impedance mode.
  * @param  Mode: specifies the high impedance mode
  *          This parameter can be one of the following values:
  *            @arg SYSCFG_VREFBUF_HIGH_IMPEDANCE_DISABLE: VREF+ pin is internally connect to VREFINT output.
  *            @arg SYSCFG_VREFBUF_HIGH_IMPEDANCE_ENABLE: VREF+ pin is high impedance.
  * @retval None
  */
void HAL_SYSCFG_VREFBUF_HighImpedanceConfig(uint32_t Mode)
{
  /* Check the parameters */
  assert_param(IS_SYSCFG_VREFBUF_HIGH_IMPEDANCE(Mode));

  MODIFY_REG(VREFBUF->CSR, VREFBUF_CSR_HIZ, Mode);
}

/**
  * @brief Tune the Internal Voltage Reference buffer (VREFBUF).
  * @param TrimmingValue specifies trimming code for VREFBUF calibration
  *        This parameter can be a number between Min_Data = 0x00 and Max_Data = 0x3F
  * @retval None
  */
void HAL_SYSCFG_VREFBUF_TrimmingConfig(uint32_t TrimmingValue)
{
  /* Check the parameters */
  assert_param(IS_SYSCFG_VREFBUF_TRIMMING(TrimmingValue));

  MODIFY_REG(VREFBUF->CCR, VREFBUF_CCR_TRIM, TrimmingValue);
}

/**
  * @brief  Enable the Internal Voltage Reference buffer (VREFBUF).
  * @retval HAL_OK/HAL_TIMEOUT
  */
HAL_StatusTypeDef HAL_SYSCFG_EnableVREFBUF(void)
{
  uint32_t tickstart;

  SET_BIT(VREFBUF->CSR, VREFBUF_CSR_ENVR);

  /* Get Start Tick*/
  tickstart = HAL_GetTick();

  /* Wait for VRR bit  */
  while (READ_BIT(VREFBUF->CSR, VREFBUF_CSR_VRR) == 0x00U)
  {
    if ((HAL_GetTick() - tickstart) > VREFBUF_TIMEOUT_VALUE)
    {
      return HAL_TIMEOUT;
    }
  }

  return HAL_OK;
}

/**
  * @brief  Disable the Internal Voltage Reference buffer (VREFBUF).
  *
  * @retval None
  */
void HAL_SYSCFG_DisableVREFBUF(void)
{
  CLEAR_BIT(VREFBUF->CSR, VREFBUF_CSR_ENVR);
}
#endif /* VREFBUF */

/**
  * @brief  Enable the I/O analog switch voltage booster
  *
  * @retval None
  */
void HAL_SYSCFG_EnableIOSwitchBooster(void)
{
  SET_BIT(SYSCFG->CFGR1, SYSCFG_CFGR1_BOOSTEN);
}

/**
  * @brief  Disable the I/O analog switch voltage booster
  *
  * @retval None
  */
void HAL_SYSCFG_DisableIOSwitchBooster(void)
{
  CLEAR_BIT(SYSCFG->CFGR1, SYSCFG_CFGR1_BOOSTEN);
}

/**
  * @brief  Enable the I/O analog switch voltage by VDD
  *
  * @retval None
  */
void HAL_SYSCFG_EnableIOSwitchVDD(void)
{
  SET_BIT(SYSCFG->CFGR1, SYSCFG_CFGR1_ANASWVDD);
}

/**
  * @brief  Disable the I/O analog switch voltage by VDD
  *
  * @retval None
  */
void HAL_SYSCFG_DisableIOSwitchVDD(void)
{
  CLEAR_BIT(SYSCFG->CFGR1, SYSCFG_CFGR1_ANASWVDD);
}


/** @brief  CCMSRAM page write protection enable
  * @param Page: This parameter is a long 32bit value and can be a value of @ref SYSCFG_CCMSRAMWRP
  * @note   write protection can only be disabled by a system reset
  * @retval None
  */
void HAL_SYSCFG_CCMSRAM_WriteProtectionEnable(uint32_t Page)
{
  assert_param(IS_SYSCFG_CCMSRAMWRP_PAGE(Page));

  SET_BIT(SYSCFG->SWPR, (uint32_t)(Page));
}


/**
  * @}
  */

/**
  * @}
  */

#endif /* HAL_MODULE_ENABLED */
/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/