Google Git
Sign in
pigweed / third_party / github / STMicroelectronics / stm32g4xx_hal_driver / 1e9f49922fbece920d63715ab1896c5a359e9e91 / . / Src / stm32g4xx_hal_rtc.c
blob: 5d9afdadfcab94c4bc53956e40e6ed0f27b9cd42 [file] [log] [blame]
/**
******************************************************************************
* @file stm32g4xx_hal_rtc.c
* @author MCD Application Team
* @brief RTC HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the Real-Time Clock (RTC) peripheral:
* + Initialization/de-initialization functions
* + Calendar (Time and Date) configuration
* + Alarms (Alarm A and Alarm B) configuration
* + WakeUp Timer configuration
* + TimeStamp configuration
* + Tampers configuration
* + Backup Data Registers configuration
* + RTC Tamper and TimeStamp Pins Selection
* + Interrupts and flags management
*
@verbatim
===============================================================================
##### RTC Operating Condition #####
===============================================================================
[..] The real-time clock (RTC) and the RTC backup registers can be powered
from the VBAT voltage when the main VDD supply is powered off.
To retain the content of the RTC backup registers and supply the RTC
when VDD is turned off, VBAT pin can be connected to an optional
standby voltage supplied by a battery or by another source.
##### Backup Domain Reset #####
===============================================================================
[..] The backup domain reset sets all RTC registers and the RCC_BDCR register
to their reset values.
A backup domain reset is generated when one of the following events occurs:
(#) Software reset, triggered by setting the BDRST bit in the
RCC Backup domain control register (RCC_BDCR).
(#) VDD or VBAT power on, if both supplies have previously been powered off.
(#) Tamper detection event resets all data backup registers.
##### Backup Domain Access #####
==================================================================
[..] After reset, the backup domain (RTC registers and RTC backup data registers)
is protected against possible unwanted write accesses.
[..] To enable access to the RTC Domain and RTC registers, proceed as follows:
(+) Enable the Power Controller (PWR) APB1 interface clock using the
__HAL_RCC_PWR_CLK_ENABLE() function.
(+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function.
(+) Select the RTC clock source using the __HAL_RCC_RTC_CONFIG() function.
(+) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() function.
[..] To enable access to the RTC Domain and RTC registers, proceed as follows:
(#) Call the function HAL_RCCEx_PeriphCLKConfig with RCC_PERIPHCLK_RTC for
PeriphClockSelection and select RTCClockSelection (LSE, LSI or HSEdiv32)
(#) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() macro.
##### How to use RTC Driver #####
===================================================================
[..]
(+) Enable the RTC domain access (see description in the section above).
(+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour
format using the HAL_RTC_Init() function.
*** Time and Date configuration ***
===================================
[..]
(+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime()
and HAL_RTC_SetDate() functions.
(+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions.
*** Alarm configuration ***
===========================
[..]
(+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function.
You can also configure the RTC Alarm with interrupt mode using the
HAL_RTC_SetAlarm_IT() function.
(+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function.
##### RTC and low power modes #####
==================================================================
[..] The MCU can be woken up from a low power mode by an RTC alternate
function.
[..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B),
RTC wakeup, RTC tamper event detection and RTC time stamp event detection.
These RTC alternate functions can wake up the system from the Stop and
Standby low power modes.
[..] The system can also wake up from low power modes without depending
on an external interrupt (Auto-wakeup mode), by using the RTC alarm
or the RTC wakeup events.
[..] The RTC provides a programmable time base for waking up from the
Stop or Standby mode at regular intervals.
Wakeup from STOP and STANDBY modes is possible only when the RTC clock source
is LSE or LSI.
*** Callback registration ***
=============================================
When The compilation define USE_HAL_RTC_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available and all callbacks
are set to the corresponding weak functions. This is the recommended configuration
in order to optimize memory/code consumption footprint/performances.
[..]
The compilation define USE_RTC_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.
Use Function @ref HAL_RTC_RegisterCallback() to register an interrupt callback.
[..]
Function @ref HAL_RTC_RegisterCallback() allows to register following callbacks:
(+) AlarmAEventCallback : RTC Alarm A Event callback.
(+) AlarmBEventCallback : RTC Alarm B Event callback.
(+) TimeStampEventCallback : RTC TimeStamp Event callback.
(+) WakeUpTimerEventCallback : RTC WakeUpTimer Event callback.
(+) Tamper1EventCallback : RTC Tamper 1 Event callback.
(+) Tamper2EventCallback : RTC Tamper 2 Event callback.
(+) Tamper3EventCallback : RTC Tamper 3 Event callback.
(+) Tamper4EventCallback : RTC Tamper 4 Event callback.
(+) Tamper5EventCallback : RTC Tamper 5 Event callback.
(+) Tamper6EventCallback : RTC Tamper 6 Event callback.
(+) Tamper7EventCallback : RTC Tamper 7 Event callback.
(+) Tamper8EventCallback : RTC Tamper 8 Event callback.
(+) InternalTamper1EventCallback : RTC InternalTamper 1 Event callback.
(+) InternalTamper2EventCallback : RTC InternalTamper 2 Event callback.
(+) InternalTamper3EventCallback : RTC InternalTamper 3 Event callback.
(+) InternalTamper5EventCallback : RTC InternalTamper 5 Event callback.
(+) InternalTamper8EventCallback : RTC InternalTamper 8 Event callback.
#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U)
(+) AlarmAEventCallback_S : RTC Alarm A Event callback_S
(+) AlarmBEventCallback_S : RTC Alarm B Event callback_S.
(+) TimeStampEventCallback_S : RTC TimeStampEvent callback_S.
(+) WakeUpTimerEventCallback_S : RTC WakeUpTimerEvent callback_S.
(+) Tamper1EventCallback_S : RTC Tamper 1 Event callback_S.
(+) Tamper2EventCallback_S : RTC Tamper 2 Event callback_S.
(+) Tamper3EventCallback_S : RTC Tamper 3 Event callback_S.
(+) Tamper4EventCallback_S : RTC Tamper 4 Event callback_S.
(+) Tamper5EventCallback_S : RTC Tamper 5 Event callback_S.
(+) Tamper6EventCallback_S : RTC Tamper 6 Event callback_S.
(+) Tamper7EventCallback_S : RTC Tamper 7 Event callback_S.
(+) Tamper8EventCallback_S : RTC Tamper 8 Event callback_S.
(+) InternalTamper1EventCallback_S : RTC InternalTamper 1 Event callback_S.
(+) InternalTamper2EventCallback_S : RTC InternalTamper 2 Event callback_S.
(+) InternalTamper3EventCallback_S : RTC InternalTamper 3 Event callback_S.
(+) InternalTamper5EventCallback_S : RTC InternalTamper 5 Event callback_S.
(+) InternalTamper8EventCallback_S : RTC InternalTamper 8 Event callback_S.
#endif
(+) MspInitCallback : RTC MspInit callback.
(+) MspDeInitCallback : RTC MspDeInit callback.
[..]
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
[..]
Use function @ref HAL_RTC_UnRegisterCallback() to reset a callback to the default
weak function.
@ref HAL_RTC_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) AlarmAEventCallback : RTC Alarm A Event callback.
(+) AlarmBEventCallback : RTC Alarm B Event callback.
(+) TimeStampEventCallback : RTC TimeStamp Event callback.
(+) WakeUpTimerEventCallback : RTC WakeUpTimer Event callback.
(+) Tamper1EventCallback : RTC Tamper 1 Event callback.
(+) Tamper2EventCallback : RTC Tamper 2 Event callback.
(+) Tamper3EventCallback : RTC Tamper 3 Event callback.
(+) Tamper4EventCallback : RTC Tamper 4 Event callback.
(+) Tamper5EventCallback : RTC Tamper 5 Event callback.
(+) Tamper6EventCallback : RTC Tamper 6 Event callback.
(+) Tamper7EventCallback : RTC Tamper 7 Event callback.
(+) Tamper8EventCallback : RTC Tamper 8 Event callback.
(+) InternalTamper1EventCallback : RTC Internal Tamper 1 Event callback.
(+) InternalTamper2EventCallback : RTC Internal Tamper 2 Event callback.
(+) InternalTamper3EventCallback : RTC Internal Tamper 3 Event callback.
(+) InternalTamper4EventCallback : RTC Internal Tamper 4 Event callback.
(+) InternalTamper5EventCallback : RTC Internal Tamper 5 Event callback.
(+) InternalTamper6EventCallback : RTC Internal Tamper 6 Event callback.
(+) InternalTamper8EventCallback : RTC Internal Tamper 8 Event callback.
#if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U)
(+) AlarmAEventCallback_S : RTC Alarm A Event callback secure.
(+) AlarmBEventCallback_S : RTC Alarm B Event callback secure.
(+) TimeStampEventCallback_S : RTC TimeStamp Event callback secure.
(+) WakeUpTimerEventCallback_S : RTC WakeUpTimer Event callback secure.
(+) Tamper1EventCallback_S : RTC Tamper 1 Event callback secure.
(+) Tamper2EventCallback_S : RTC Tamper 2 Event callback secure.
(+) Tamper3EventCallback_S : RTC Tamper 3 Event callback secure.
(+) Tamper4EventCallback_S : RTC Tamper 4 Event callback secure.
(+) Tamper5EventCallback_S : RTC Tamper 5 Event callback secure.
(+) Tamper6EventCallback_S : RTC Tamper 6 Event callback secure.
(+) Tamper7EventCallback_S : RTC Tamper 7 Event callback secure.
(+) Tamper8EventCallback_S : RTC Tamper 8 Event callback secure.
(+) InternalTamper1EventCallback_S : RTC Internal Tamper 1 Event callback secure.
(+) InternalTamper2EventCallback_S : RTC Internal Tamper 2 Event callback secure.
(+) InternalTamper3EventCallback_S : RTC Internal Tamper 3 Event callback secure.
(+) InternalTamper4EventCallback_S : RTC Internal Tamper 4 Event callback secure.
(+) InternalTamper5EventCallback_S : RTC Internal Tamper 5 Event callback secure.
(+) InternalTamper6EventCallback_S : RTC Internal Tamper 6 Event callback secure.
(+) InternalTamper8EventCallback_S : RTC Internal Tamper 8 Event callback secure.
#endif
(+) MspInitCallback : RTC MspInit callback.
(+) MspDeInitCallback : RTC MspDeInit callback.
[..]
By default, after the @ref HAL_RTC_Init() and when the state is HAL_RTC_STATE_RESET,
all callbacks are set to the corresponding weak functions :
examples @ref AlarmAEventCallback(), @ref TimeStampEventCallback().
Exception done for MspInit and MspDeInit callbacks that are reset to the legacy weak function
in the @ref HAL_RTC_Init()/@ref HAL_RTC_DeInit() only when these callbacks are null
(not registered beforehand).
If not, MspInit or MspDeInit are not null, @ref HAL_RTC_Init()/@ref HAL_RTC_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand)
[..]
Callbacks can be registered/unregistered in HAL_RTC_STATE_READY state only.
Exception done MspInit/MspDeInit that can be registered/unregistered
in HAL_RTC_STATE_READY or HAL_RTC_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
using @ref HAL_RTC_RegisterCallback() before calling @ref HAL_RTC_DeInit()
or @ref HAL_RTC_Init() function.
[..]
When The compilation define USE_HAL_RTC_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available and all callbacks
are set to the corresponding weak functions.
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32g4xx_hal.h"
/** @addtogroup STM32G4xx_HAL_Driver
* @{
*/
/** @addtogroup RTC
* @brief RTC HAL module driver
* @{
*/
#ifdef HAL_RTC_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup RTC_Exported_Functions
* @{
*/
/** @addtogroup RTC_Exported_Functions_Group1
* @brief Initialization and Configuration functions
*
@verbatim
===============================================================================
##### Initialization and de-initialization functions #####
===============================================================================
[..] This section provides functions allowing to initialize and configure the
RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable
RTC registers Write protection, enter and exit the RTC initialization mode,
RTC registers synchronization check and reference clock detection enable.
(#) The RTC Prescaler is programmed to generate the RTC 1Hz time base.
It is split into 2 programmable prescalers to minimize power consumption.
(++) A 7-bit asynchronous prescaler and a 15-bit synchronous prescaler.
(++) When both prescalers are used, it is recommended to configure the
asynchronous prescaler to a high value to minimize power consumption.
(#) All RTC registers are Write protected. Writing to the RTC registers
is enabled by writing a key into the Write Protection register, RTC_WPR.
(#) To configure the RTC Calendar, user application should enter
initialization mode. In this mode, the calendar counter is stopped
and its value can be updated. When the initialization sequence is
complete, the calendar restarts counting after 4 RTCCLK cycles.
(#) To read the calendar through the shadow registers after Calendar
initialization, calendar update or after wakeup from low power modes
the software must first clear the RSF flag. The software must then
wait until it is set again before reading the calendar, which means
that the calendar registers have been correctly copied into the
RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function
implements the above software sequence (RSF clear and RSF check).
@endverbatim
* @{
*/
/**
* @brief Initialize the RTC peripheral
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc)
{
HAL_StatusTypeDef status = HAL_ERROR;
/* Check the RTC peripheral state */
if (hrtc != NULL)
{
/* Check the parameters */
assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat));
assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv));
assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv));
assert_param(IS_RTC_OUTPUT(hrtc->Init.OutPut));
assert_param(IS_RTC_OUTPUT_REMAP(hrtc->Init.OutPutRemap));
assert_param(IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity));
assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType));
assert_param(IS_RTC_OUTPUT_PULLUP(hrtc->Init.OutPutPullUp));
#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
if (hrtc->State == HAL_RTC_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hrtc->Lock = HAL_UNLOCKED;
hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback; /* Legacy weak AlarmAEventCallback */
hrtc->AlarmBEventCallback = HAL_RTCEx_AlarmBEventCallback; /* Legacy weak AlarmBEventCallback */
hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback; /* Legacy weak TimeStampEventCallback */
hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */
hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback; /* Legacy weak Tamper1EventCallback */
hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback; /* Legacy weak Tamper2EventCallback */
#if (RTC_TAMP_NB == 3)
hrtc->Tamper3EventCallback = HAL_RTCEx_Tamper3EventCallback; /* Legacy weak Tamper3EventCallback */
#endif /* RTC_TAMP_NB */
#ifdef RTC_TAMP_INT_1_SUPPORT
hrtc->InternalTamper1EventCallback = HAL_RTCEx_InternalTamper1EventCallback; /*!< Legacy weak InternalTamper1EventCallback */
#endif /* RTC_TAMP_INT_1_SUPPORT */
#ifdef RTC_TAMP_INT_2_SUPPORT
hrtc->InternalTamper2EventCallback = HAL_RTCEx_InternalTamper2EventCallback; /*!< Legacy weak InternalTamper2EventCallback */
#endif /* RTC_TAMP_INT_2_SUPPORT */
hrtc->InternalTamper3EventCallback = HAL_RTCEx_InternalTamper3EventCallback; /*!< Legacy weak InternalTamper3EventCallback */
hrtc->InternalTamper4EventCallback = HAL_RTCEx_InternalTamper4EventCallback; /*!< Legacy weak InternalTamper4EventCallback */
hrtc->InternalTamper5EventCallback = HAL_RTCEx_InternalTamper5EventCallback; /*!< Legacy weak InternalTamper5EventCallback */
#ifdef RTC_TAMP_INT_6_SUPPORT
hrtc->InternalTamper6EventCallback = HAL_RTCEx_InternalTamper6EventCallback; /*!< Legacy weak InternalTamper6EventCallback */
#endif /* RTC_TAMP_INT_6_SUPPORT */
#ifdef RTC_TAMP_INT_7_SUPPORT
hrtc->InternalTamper7EventCallback = HAL_RTCEx_InternalTamper7EventCallback; /*!< Legacy weak InternalTamper7EventCallback */
#endif /* RTC_TAMP_INT_7_SUPPORT */
if (hrtc->MspInitCallback == NULL)
{
hrtc->MspInitCallback = HAL_RTC_MspInit;
}
/* Init the low level hardware */
hrtc->MspInitCallback(hrtc);
if (hrtc->MspDeInitCallback == NULL)
{
hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
}
}
#else
if (hrtc->State == HAL_RTC_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hrtc->Lock = HAL_UNLOCKED;
/* Initialize RTC MSP */
HAL_RTC_MspInit(hrtc);
}
#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */
/* Set RTC state */
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Enter Initialization mode */
status = RTC_EnterInitMode(hrtc);
if (status == HAL_OK)
{
/* Clear RTC_CR FMT, OSEL and POL Bits */
CLEAR_BIT(RTC->CR, (RTC_CR_FMT | RTC_CR_POL | RTC_CR_OSEL | RTC_CR_TAMPOE));
/* Set RTC_CR register */
SET_BIT(RTC->CR, (hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity));
/* Configure the RTC PRER */
WRITE_REG(RTC->PRER, ((hrtc->Init.SynchPrediv) | (hrtc->Init.AsynchPrediv << RTC_PRER_PREDIV_A_Pos)));
/* Exit Initialization mode */
status = RTC_ExitInitMode(hrtc);
if (status == HAL_OK)
{
MODIFY_REG(RTC->CR, \
RTC_CR_TAMPALRM_PU | RTC_CR_TAMPALRM_TYPE | RTC_CR_OUT2EN, \
hrtc->Init.OutPutPullUp | hrtc->Init.OutPutType | hrtc->Init.OutPutRemap);
}
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
if (status == HAL_OK)
{
hrtc->State = HAL_RTC_STATE_READY;
}
}
return status;
}
/**
* @brief DeInitialize the RTC peripheral.
* @note This function does not reset the RTC Backup Data registers.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc)
{
HAL_StatusTypeDef status;
/* Set RTC state */
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
status = RTC_EnterInitMode(hrtc);
/* Set Initialization mode */
if (status != HAL_OK)
{
/* Set RTC state */
hrtc->State = HAL_RTC_STATE_ERROR;
}
else
{
/* Reset all RTC CR register bits */
CLEAR_REG(RTC->CR);
WRITE_REG(RTC->DR, (uint32_t)(RTC_DR_WDU_0 | RTC_DR_MU_0 | RTC_DR_DU_0));
CLEAR_REG(RTC->TR);
WRITE_REG(RTC->WUTR, RTC_WUTR_WUT);
WRITE_REG(RTC->PRER, ((uint32_t)(RTC_PRER_PREDIV_A | 0xFFU)));
CLEAR_REG(RTC->ALRMAR);
CLEAR_REG(RTC->ALRMBR);
CLEAR_REG(RTC->SHIFTR);
CLEAR_REG(RTC->CALR);
CLEAR_REG(RTC->ALRMASSR);
CLEAR_REG(RTC->ALRMBSSR);
WRITE_REG(RTC->SCR, RTC_SCR_CITSF | RTC_SCR_CTSOVF | RTC_SCR_CTSF | RTC_SCR_CWUTF | RTC_SCR_CALRBF | RTC_SCR_CALRAF);
/* Exit initialization mode */
CLEAR_BIT(RTC->ICSR, RTC_ICSR_INIT);
status = HAL_RTC_WaitForSynchro(hrtc);
if (status != HAL_OK)
{
hrtc->State = HAL_RTC_STATE_ERROR;
}
else
{
/* Reset TAMP registers */
WRITE_REG(TAMP->CR1, RTC_INT_TAMPER_ALL);
CLEAR_REG(TAMP->CR2);
CLEAR_REG(TAMP->FLTCR);
}
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
if (status == HAL_OK)
{
#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
if (hrtc->MspDeInitCallback == NULL)
{
hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
}
/* DeInit the low level hardware: CLOCK, NVIC.*/
hrtc->MspDeInitCallback(hrtc);
#else
/* De-Initialize RTC MSP */
HAL_RTC_MspDeInit(hrtc);
#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */
hrtc->State = HAL_RTC_STATE_RESET;
}
/* Release Lock */
__HAL_UNLOCK(hrtc);
return status;
}
#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
/**
* @brief Register a User RTC Callback
* To be used instead of the weak predefined callback
* @param hrtc RTC handle
* @param CallbackID ID of the callback to be registered
* This parameter can be one of the following values:
* @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID Alarm A Event Callback ID
* @arg @ref HAL_RTC_ALARM_B_EVENT_CB_ID Alarm B Event Callback ID
* @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID TimeStamp Event Callback ID
* @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID WakeUp Timer Event Callback ID
* @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID Tamper 1 Callback ID
* @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID Tamper 2 Callback ID
* @arg @ref HAL_RTC_TAMPER3_EVENT_CB_ID Tamper 3 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER1_EVENT_CB_ID Internal Tamper 1 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER2_EVENT_CB_ID Internal Tamper 2 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER3_EVENT_CB_ID Internal Tamper 3 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER4_EVENT_CB_ID Internal Tamper 4 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER5_EVENT_CB_ID Internal Tamper 5 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER6_EVENT_CB_ID Internal Tamper 6 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER7_EVENT_CB_ID Internal Tamper 7 Callback ID
* @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID
* @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID
* @param pCallback pointer to the Callback function
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_RegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID,
pRTC_CallbackTypeDef pCallback)
{
HAL_StatusTypeDef status = HAL_OK;
if (pCallback == NULL)
{
return HAL_ERROR;
}
/* Process locked */
__HAL_LOCK(hrtc);
if (HAL_RTC_STATE_READY == hrtc->State)
{
switch (CallbackID)
{
case HAL_RTC_ALARM_A_EVENT_CB_ID :
hrtc->AlarmAEventCallback = pCallback;
break;
case HAL_RTC_ALARM_B_EVENT_CB_ID :
hrtc->AlarmBEventCallback = pCallback;
break;
case HAL_RTC_TIMESTAMP_EVENT_CB_ID :
hrtc->TimeStampEventCallback = pCallback;
break;
case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID :
hrtc->WakeUpTimerEventCallback = pCallback;
break;
case HAL_RTC_TAMPER1_EVENT_CB_ID :
hrtc->Tamper1EventCallback = pCallback;
break;
case HAL_RTC_TAMPER2_EVENT_CB_ID :
hrtc->Tamper2EventCallback = pCallback;
break;
#if (RTC_TAMP_NB == 3)
case HAL_RTC_TAMPER3_EVENT_CB_ID :
hrtc->Tamper3EventCallback = pCallback;
break;
#endif /* RTC_TAMP_NB */
#ifdef RTC_TAMP_INT_1_SUPPORT
case HAL_RTC_INTERNAL_TAMPER1_EVENT_CB_ID :
hrtc->InternalTamper1EventCallback = pCallback;
break;
#endif /* RTC_TAMP_INT_1_SUPPORT */
#ifdef RTC_TAMP_INT_2_SUPPORT
case HAL_RTC_INTERNAL_TAMPER2_EVENT_CB_ID :
hrtc->InternalTamper2EventCallback = pCallback;
break;
#endif /* RTC_TAMP_INT_2_SUPPORT */
case HAL_RTC_INTERNAL_TAMPER3_EVENT_CB_ID :
hrtc->InternalTamper3EventCallback = pCallback;
break;
case HAL_RTC_INTERNAL_TAMPER4_EVENT_CB_ID :
hrtc->InternalTamper4EventCallback = pCallback;
break;
case HAL_RTC_INTERNAL_TAMPER5_EVENT_CB_ID :
hrtc->InternalTamper5EventCallback = pCallback;
break;
#ifdef RTC_TAMP_INT_6_SUPPORT
case HAL_RTC_INTERNAL_TAMPER6_EVENT_CB_ID :
hrtc->InternalTamper6EventCallback = pCallback;
break;
#endif /* RTC_TAMP_INT_6_SUPPORT */
#ifdef RTC_TAMP_INT_7_SUPPORT
case HAL_RTC_INTERNAL_TAMPER7_EVENT_CB_ID :
hrtc->InternalTamper7EventCallback = pCallback;
break;
#endif /* RTC_TAMP_INT_7_SUPPORT */
case HAL_RTC_MSPINIT_CB_ID :
hrtc->MspInitCallback = pCallback;
break;
case HAL_RTC_MSPDEINIT_CB_ID :
hrtc->MspDeInitCallback = pCallback;
break;
default :
/* Return error status */
status = HAL_ERROR;
break;
}
}
else if (HAL_RTC_STATE_RESET == hrtc->State)
{
switch (CallbackID)
{
case HAL_RTC_MSPINIT_CB_ID :
hrtc->MspInitCallback = pCallback;
break;
case HAL_RTC_MSPDEINIT_CB_ID :
hrtc->MspDeInitCallback = pCallback;
break;
default :
/* Return error status */
status = HAL_ERROR;
break;
}
}
else
{
/* Return error status */
status = HAL_ERROR;
}
/* Release Lock */
__HAL_UNLOCK(hrtc);
return status;
}
/**
* @brief Unregister an RTC Callback
* RTC callback is redirected to the weak predefined callback
* @param hrtc RTC handle
* @param CallbackID ID of the callback to be unregistered
* This parameter can be one of the following values:
* @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID Alarm A Event Callback ID
* @arg @ref HAL_RTC_ALARM_B_EVENT_CB_ID Alarm B Event Callback ID
* @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID TimeStamp Event Callback ID
* @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID WakeUp Timer Event Callback ID
* @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID Tamper 1 Callback ID
* @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID Tamper 2 Callback ID
* @arg @ref HAL_RTC_TAMPER3_EVENT_CB_ID Tamper 3 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER1_EVENT_CB_ID Internal Tamper 1 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER2_EVENT_CB_ID Internal Tamper 2 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER3_EVENT_CB_ID Internal Tamper 3 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER4_EVENT_CB_ID Internal Tamper 4 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER5_EVENT_CB_ID Internal Tamper 5 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER6_EVENT_CB_ID Internal Tamper 6 Callback ID
* @arg @ref HAL_RTC_INTERNAL_TAMPER7_EVENT_CB_ID Internal Tamper 7 Callback ID
* @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID
* @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_UnRegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID)
{
HAL_StatusTypeDef status = HAL_OK;
/* Process locked */
__HAL_LOCK(hrtc);
if (HAL_RTC_STATE_READY == hrtc->State)
{
switch (CallbackID)
{
case HAL_RTC_ALARM_A_EVENT_CB_ID :
hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback; /* Legacy weak AlarmAEventCallback */
break;
case HAL_RTC_ALARM_B_EVENT_CB_ID :
hrtc->AlarmBEventCallback = HAL_RTCEx_AlarmBEventCallback; /* Legacy weak AlarmBEventCallback */
break;
case HAL_RTC_TIMESTAMP_EVENT_CB_ID :
hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback; /* Legacy weak TimeStampEventCallback */
break;
case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID :
hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */
break;
case HAL_RTC_TAMPER1_EVENT_CB_ID :
hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback; /* Legacy weak Tamper1EventCallback */
break;
case HAL_RTC_TAMPER2_EVENT_CB_ID :
hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback; /* Legacy weak Tamper2EventCallback */
break;
#if (RTC_TAMP_NB == 3)
case HAL_RTC_TAMPER3_EVENT_CB_ID :
hrtc->Tamper3EventCallback = HAL_RTCEx_Tamper3EventCallback; /* Legacy weak Tamper3EventCallback */
break;
#endif /* RTC_TAMP_NB */
#ifdef RTC_TAMP_INT_1_SUPPORT
case HAL_RTC_INTERNAL_TAMPER1_EVENT_CB_ID :
hrtc->InternalTamper1EventCallback = HAL_RTCEx_InternalTamper1EventCallback; /* Legacy weak InternalTamper1EventCallback */
break;
#endif /* RTC_TAMP_INT_1_SUPPORT */
#ifdef RTC_TAMP_INT_2_SUPPORT
case HAL_RTC_INTERNAL_TAMPER2_EVENT_CB_ID :
hrtc->InternalTamper2EventCallback = HAL_RTCEx_InternalTamper2EventCallback; /* Legacy weak InternalTamper2EventCallback */
break;
#endif /* RTC_TAMP_INT_2_SUPPORT */
case HAL_RTC_INTERNAL_TAMPER3_EVENT_CB_ID :
hrtc->InternalTamper3EventCallback = HAL_RTCEx_InternalTamper3EventCallback; /* Legacy weak InternalTamper3EventCallback */
break;
case HAL_RTC_INTERNAL_TAMPER4_EVENT_CB_ID :
hrtc->InternalTamper4EventCallback = HAL_RTCEx_InternalTamper4EventCallback; /* Legacy weak InternalTamper4EventCallback */
break;
case HAL_RTC_INTERNAL_TAMPER5_EVENT_CB_ID :
hrtc->InternalTamper5EventCallback = HAL_RTCEx_InternalTamper5EventCallback; /* Legacy weak InternalTamper5EventCallback */
break;
#ifdef RTC_TAMP_INT_6_SUPPORT
case HAL_RTC_INTERNAL_TAMPER6_EVENT_CB_ID :
hrtc->InternalTamper6EventCallback = HAL_RTCEx_InternalTamper6EventCallback; /* Legacy weak InternalTamper6EventCallback */
break;
#endif /* RTC_TAMP_INT_6_SUPPORT */
#ifdef RTC_TAMP_INT_7_SUPPORT
case HAL_RTC_INTERNAL_TAMPER7_EVENT_CB_ID :
hrtc->InternalTamper7EventCallback = HAL_RTCEx_InternalTamper7EventCallback; /* Legacy weak InternalTamper7EventCallback */
break;
#endif /* RTC_TAMP_INT_7_SUPPORT */
case HAL_RTC_MSPINIT_CB_ID :
hrtc->MspInitCallback = HAL_RTC_MspInit;
break;
case HAL_RTC_MSPDEINIT_CB_ID :
hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
break;
default :
/* Return error status */
status = HAL_ERROR;
break;
}
}
else if (HAL_RTC_STATE_RESET == hrtc->State)
{
switch (CallbackID)
{
case HAL_RTC_MSPINIT_CB_ID :
hrtc->MspInitCallback = HAL_RTC_MspInit;
break;
case HAL_RTC_MSPDEINIT_CB_ID :
hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
break;
default :
/* Return error status */
status = HAL_ERROR;
break;
}
}
else
{
/* Return error status */
status = HAL_ERROR;
}
/* Release Lock */
__HAL_UNLOCK(hrtc);
return status;
}
#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
/**
* @brief Initialize the RTC MSP.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTC_MspInit(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTC_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitialize the RTC MSP.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTC_MspDeInit could be implemented in the user file
*/
}
/**
* @}
*/
/** @addtogroup RTC_Exported_Functions_Group2
* @brief RTC Time and Date functions
*
@verbatim
===============================================================================
##### RTC Time and Date functions #####
===============================================================================
[..] This section provides functions allowing to configure Time and Date features
@endverbatim
* @{
*/
/**
* @brief Set RTC current time.
* @param hrtc RTC handle
* @param sTime Pointer to Time structure
* @param Format Specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)
{
uint32_t tmpreg;
HAL_StatusTypeDef status;
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving));
assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Enter Initialization mode */
status = RTC_EnterInitMode(hrtc);
if (status == HAL_OK)
{
if (Format == RTC_FORMAT_BIN)
{
if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
{
assert_param(IS_RTC_HOUR12(sTime->Hours));
assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));
}
else
{
sTime->TimeFormat = 0x00U;
assert_param(IS_RTC_HOUR24(sTime->Hours));
}
assert_param(IS_RTC_MINUTES(sTime->Minutes));
assert_param(IS_RTC_SECONDS(sTime->Seconds));
tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(sTime->Hours) << RTC_TR_HU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sTime->Minutes) << RTC_TR_MNU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sTime->Seconds) << RTC_TR_SU_Pos) | \
(((uint32_t)sTime->TimeFormat) << RTC_TR_PM_Pos));
}
else
{
if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
{
assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sTime->Hours)));
assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));
}
else
{
sTime->TimeFormat = 0x00U;
assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours)));
}
assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes)));
assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds)));
tmpreg = (((uint32_t)(sTime->Hours) << RTC_TR_HU_Pos) | \
((uint32_t)(sTime->Minutes) << RTC_TR_MNU_Pos) | \
((uint32_t)(sTime->Seconds) << RTC_TR_SU_Pos) | \
((uint32_t)(sTime->TimeFormat) << RTC_TR_PM_Pos));
}
/* Set the RTC_TR register */
WRITE_REG(RTC->TR, (tmpreg & RTC_TR_RESERVED_MASK));
/* This interface is deprecated. To manage Daylight Saving Time, please use HAL_RTC_DST_xxx functions */
CLEAR_BIT(RTC->CR, RTC_CR_BKP);
/* This interface is deprecated. To manage Daylight Saving Time, please use HAL_RTC_DST_xxx functions */
SET_BIT(RTC->CR, (sTime->DayLightSaving | sTime->StoreOperation));
/* Exit Initialization mode */
status = RTC_ExitInitMode(hrtc);
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
if (status == HAL_OK)
{
hrtc->State = HAL_RTC_STATE_READY;
}
__HAL_UNLOCK(hrtc);
return status;
}
/**
* @brief Get RTC current time.
* @note You can use SubSeconds and SecondFraction (sTime structure fields returned) to convert SubSeconds
* value in second fraction ratio with time unit following generic formula:
* Second fraction ratio * time_unit= [(SecondFraction-SubSeconds)/(SecondFraction+1)] * time_unit
* This conversion can be performed only if no shift operation is pending (ie. SHFP=0) when PREDIV_S >= SS
* @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values
* in the higher-order calendar shadow registers to ensure consistency between the time and date values.
* Reading RTC current time locks the values in calendar shadow registers until Current date is read
* to ensure consistency between the time and date values.
* @param hrtc RTC handle
* @param sTime Pointer to Time structure with Hours, Minutes and Seconds fields returned
* with input format (BIN or BCD), also SubSeconds field returning the
* RTC_SSR register content and SecondFraction field the Synchronous pre-scaler
* factor to be used for second fraction ratio computation.
* @param Format Specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)
{
uint32_t tmpreg;
UNUSED(hrtc);
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
/* Get subseconds structure field from the corresponding register*/
sTime->SubSeconds = READ_REG(RTC->SSR);
/* Get SecondFraction structure field from the corresponding register field*/
sTime->SecondFraction = (uint32_t)(READ_REG(RTC->PRER) & RTC_PRER_PREDIV_S);
/* Get the TR register */
tmpreg = (uint32_t)(READ_REG(RTC->TR) & RTC_TR_RESERVED_MASK);
/* Fill the structure fields with the read parameters */
sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> RTC_TR_HU_Pos);
sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >> RTC_TR_MNU_Pos);
sTime->Seconds = (uint8_t)((tmpreg & (RTC_TR_ST | RTC_TR_SU)) >> RTC_TR_SU_Pos);
sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> RTC_TR_PM_Pos);
/* Check the input parameters format */
if (Format == RTC_FORMAT_BIN)
{
/* Convert the time structure parameters to Binary format */
sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours);
sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes);
sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds);
}
return HAL_OK;
}
/**
* @brief Set RTC current date.
* @param hrtc RTC handle
* @param sDate Pointer to date structure
* @param Format specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)
{
uint32_t datetmpreg;
HAL_StatusTypeDef status;
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
if ((Format == RTC_FORMAT_BIN) && ((sDate->Month & 0x10U) == 0x10U))
{
sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10U)) + (uint8_t)0x0AU);
}
assert_param(IS_RTC_WEEKDAY(sDate->WeekDay));
if (Format == RTC_FORMAT_BIN)
{
assert_param(IS_RTC_YEAR(sDate->Year));
assert_param(IS_RTC_MONTH(sDate->Month));
assert_param(IS_RTC_DATE(sDate->Date));
datetmpreg = (((uint32_t)RTC_ByteToBcd2(sDate->Year) << RTC_DR_YU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sDate->Month) << RTC_DR_MU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sDate->Date) << RTC_DR_DU_Pos) | \
((uint32_t)sDate->WeekDay << RTC_DR_WDU_Pos));
}
else
{
assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(sDate->Year)));
assert_param(IS_RTC_MONTH(RTC_Bcd2ToByte(sDate->Month)));
assert_param(IS_RTC_DATE(RTC_Bcd2ToByte(sDate->Date)));
datetmpreg = ((((uint32_t)sDate->Year) << RTC_DR_YU_Pos) | \
(((uint32_t)sDate->Month) << RTC_DR_MU_Pos) | \
(((uint32_t)sDate->Date) << RTC_DR_DU_Pos) | \
(((uint32_t)sDate->WeekDay) << RTC_DR_WDU_Pos));
}
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Enter Initialization mode */
status = RTC_EnterInitMode(hrtc);
if (status == HAL_OK)
{
/* Set the RTC_DR register */
WRITE_REG(RTC->DR, (uint32_t)(datetmpreg & RTC_DR_RESERVED_MASK));
/* Exit Initialization mode */
status = RTC_ExitInitMode(hrtc);
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
if (status == HAL_OK)
{
hrtc->State = HAL_RTC_STATE_READY ;
}
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return status;
}
/**
* @brief Get RTC current date.
* @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values
* in the higher-order calendar shadow registers to ensure consistency between the time and date values.
* Reading RTC current time locks the values in calendar shadow registers until Current date is read.
* @param hrtc RTC handle
* @param sDate Pointer to Date structure
* @param Format Specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)
{
uint32_t datetmpreg;
UNUSED(hrtc);
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
/* Get the DR register */
datetmpreg = (uint32_t)(READ_REG(RTC->DR) & RTC_DR_RESERVED_MASK);
/* Fill the structure fields with the read parameters */
sDate->Year = (uint8_t)((datetmpreg & (RTC_DR_YT | RTC_DR_YU)) >> RTC_DR_YU_Pos);
sDate->Month = (uint8_t)((datetmpreg & (RTC_DR_MT | RTC_DR_MU)) >> RTC_DR_MU_Pos);
sDate->Date = (uint8_t)((datetmpreg & (RTC_DR_DT | RTC_DR_DU)) >> RTC_DR_DU_Pos);
sDate->WeekDay = (uint8_t)((datetmpreg & (RTC_DR_WDU)) >> RTC_DR_WDU_Pos);
/* Check the input parameters format */
if (Format == RTC_FORMAT_BIN)
{
/* Convert the date structure parameters to Binary format */
sDate->Year = (uint8_t)RTC_Bcd2ToByte(sDate->Year);
sDate->Month = (uint8_t)RTC_Bcd2ToByte(sDate->Month);
sDate->Date = (uint8_t)RTC_Bcd2ToByte(sDate->Date);
}
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup RTC_Exported_Functions_Group3
* @brief RTC Alarm functions
*
@verbatim
===============================================================================
##### RTC Alarm functions #####
===============================================================================
[..] This section provides functions allowing to configure Alarm feature
@endverbatim
* @{
*/
/**
* @brief Set the specified RTC Alarm.
* @param hrtc RTC handle
* @param sAlarm Pointer to Alarm structure
* @param Format Specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format)
{
uint32_t tickstart;
uint32_t tmpreg;
uint32_t subsecondtmpreg;
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
assert_param(IS_RTC_ALARM(sAlarm->Alarm));
assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask));
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel));
assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds));
assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
if (Format == RTC_FORMAT_BIN)
{
if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
{
assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours));
assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
}
else
{
sAlarm->AlarmTime.TimeFormat = 0x00U;
assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours));
}
assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
#ifdef USE_FULL_ASSERT
if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
}
else
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
}
#endif /* USE_FULL_ASSERT*/
tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds) << RTC_ALRMAR_SU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_ALRMAR_PM_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
((uint32_t)sAlarm->AlarmMask));
}
else /* Format BCD */
{
if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
{
assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
}
else
{
sAlarm->AlarmTime.TimeFormat = 0x00U;
assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
}
assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
#ifdef USE_FULL_ASSERT
if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
}
else
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
}
#endif /* USE_FULL_ASSERT */
tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.Seconds) << RTC_ALRMAR_SU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_ALRMAR_PM_Pos) | \
((uint32_t)(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
((uint32_t)sAlarm->AlarmMask));
}
/* Configure the Alarm A or Alarm B Sub Second registers */
subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask));
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Configure the Alarm register */
if (sAlarm->Alarm == RTC_ALARM_A)
{
/* Disable the Alarm A interrupt */
/* In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, (RTC_CR_ALRAE | RTC_CR_ALRAIE));
/* Clear flag alarm A */
WRITE_REG(RTC->SCR, RTC_SCR_CALRAF);
tickstart = HAL_GetTick();
/* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
while (READ_BIT(RTC->ICSR, RTC_ICSR_ALRAWF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
WRITE_REG(RTC->ALRMAR, tmpreg);
/* Configure the Alarm A Sub Second register */
WRITE_REG(RTC->ALRMASSR, subsecondtmpreg);
/* Configure the Alarm state: Enable Alarm */
SET_BIT(RTC->CR, RTC_CR_ALRAE);
}
else
{
/* Disable the Alarm B interrupt */
/* In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, (RTC_CR_ALRBE | RTC_CR_ALRBIE));
/* Clear flag alarm B */
WRITE_REG(RTC->SCR, RTC_SCR_CALRBF);
tickstart = HAL_GetTick();
/* Wait till RTC ALRBWF flag is set and if Time out is reached exit */
while (READ_BIT(RTC->ICSR, RTC_ICSR_ALRBWF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
WRITE_REG(RTC->ALRMBR, tmpreg);
/* Configure the Alarm B Sub Second register */
WRITE_REG(RTC->ALRMBSSR, subsecondtmpreg);
/* Configure the Alarm state: Enable Alarm */
SET_BIT(RTC->CR, RTC_CR_ALRBE);
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Set the specified RTC Alarm with Interrupt.
* @note The Alarm register can only be written when the corresponding Alarm
* is disabled (Use the HAL_RTC_DeactivateAlarm()).
* @note The HAL_RTC_SetTime() must be called before enabling the Alarm feature.
* @param hrtc RTC handle
* @param sAlarm Pointer to Alarm structure
* @param Format Specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format)
{
uint32_t tickstart;
uint32_t tmpreg;
uint32_t subsecondtmpreg;
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
assert_param(IS_RTC_ALARM(sAlarm->Alarm));
assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask));
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel));
assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds));
assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
if (Format == RTC_FORMAT_BIN)
{
if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
{
assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours));
assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
}
else
{
sAlarm->AlarmTime.TimeFormat = 0x00U;
assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours));
}
assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
#ifdef USE_FULL_ASSERT
if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
}
else
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
}
#endif /* USE_FULL_ASSERT */
tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds) << RTC_ALRMAR_SU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_ALRMAR_PM_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
((uint32_t)sAlarm->AlarmMask));
}
else /* Format BCD */
{
if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
{
assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
}
else
{
sAlarm->AlarmTime.TimeFormat = 0x00U;
assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
}
assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
#ifdef USE_FULL_ASSERT
if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
}
else
{
assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
}
#endif /* USE_FULL_ASSERT */
tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.Seconds) << RTC_ALRMAR_SU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_ALRMAR_PM_Pos) | \
((uint32_t)(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
((uint32_t)sAlarm->AlarmMask));
}
/* Configure the Alarm A or Alarm B Sub Second registers */
subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask));
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Configure the Alarm register */
if (sAlarm->Alarm == RTC_ALARM_A)
{
/* Disable the Alarm A interrupt */
CLEAR_BIT(RTC->CR, (RTC_CR_ALRAE | RTC_CR_ALRAIE));
/* Clear flag alarm A */
WRITE_REG(RTC->SCR, RTC_SCR_CALRAF);
__HAL_RTC_ALARM_EXTI_CLEAR_IT();
tickstart = HAL_GetTick();
/* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
while (READ_BIT(RTC->ICSR, RTC_ICSR_ALRAWF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
WRITE_REG(RTC->ALRMAR, tmpreg);
/* Configure the Alarm A Sub Second register */
WRITE_REG(RTC->ALRMASSR, subsecondtmpreg);
/* Configure the Alarm interrupt : Enable Alarm */
SET_BIT(RTC->CR, (RTC_CR_ALRAE | RTC_CR_ALRAIE));
}
else
{
/* Disable the Alarm B interrupt */
CLEAR_BIT(RTC->CR, (RTC_CR_ALRBE | RTC_CR_ALRBIE));
/* Clear flag alarm B */
WRITE_REG(RTC->SCR, RTC_SCR_CALRBF);
__HAL_RTC_ALARM_EXTI_CLEAR_IT();
tickstart = HAL_GetTick();
/* Wait till RTC ALRBWF flag is set and if Time out is reached exit */
while (READ_BIT(RTC->ICSR, RTC_ICSR_ALRBWF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
WRITE_REG(RTC->ALRMBR, tmpreg);
/* Configure the Alarm B Sub Second register */
WRITE_REG(RTC->ALRMBSSR, subsecondtmpreg);
/* Configure the Alarm B interrupt : Enable Alarm */
SET_BIT(RTC->CR, (RTC_CR_ALRBE | RTC_CR_ALRBIE));
}
/* RTC Alarm Interrupt Configuration: EXTI configuration */
__HAL_RTC_ALARM_EXTI_ENABLE_IT();
__HAL_RTC_ALARM_EXTI_RISING_IT();
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Deactivate the specified RTC Alarm.
* @param hrtc RTC handle
* @param Alarm Specifies the Alarm.
* This parameter can be one of the following values:
* @arg RTC_ALARM_A: AlarmA
* @arg RTC_ALARM_B: AlarmB
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm)
{
uint32_t tickstart;
/* Check the parameters */
assert_param(IS_RTC_ALARM(Alarm));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
if (Alarm == RTC_ALARM_A)
{
/* AlarmA */
/* In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, RTC_CR_ALRAE | RTC_CR_ALRAIE);
__HAL_RTC_ALARM_EXTI_CLEAR_IT();
tickstart = HAL_GetTick();
/* Wait till RTC ALRxWF flag is set and if Time out is reached exit */
while (READ_BIT(RTC->ICSR, RTC_ICSR_ALRAWF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
}
else
{
/* AlarmB */
/* In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, RTC_CR_ALRBE | RTC_CR_ALRBIE);
__HAL_RTC_ALARM_EXTI_CLEAR_IT();
tickstart = HAL_GetTick();
/* Wait till RTC ALRxWF flag is set and if Time out is reached exit */
while (READ_BIT(RTC->ICSR, RTC_ICSR_ALRBWF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Get the RTC Alarm value and masks.
* @param hrtc RTC handle
* @param sAlarm Pointer to Date structure
* @param Alarm Specifies the Alarm.
* This parameter can be one of the following values:
* @arg RTC_ALARM_A: AlarmA
* @arg RTC_ALARM_B: AlarmB
* @param Format Specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format)
{
uint32_t tmpreg, subsecondtmpreg;
UNUSED(hrtc);
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
assert_param(IS_RTC_ALARM(Alarm));
if (Alarm == RTC_ALARM_A)
{
/* AlarmA */
sAlarm->Alarm = RTC_ALARM_A;
tmpreg = READ_REG(RTC->ALRMAR);
subsecondtmpreg = (uint32_t)(READ_REG(RTC->ALRMASSR) & RTC_ALRMASSR_SS);
/* Fill the structure with the read parameters */
sAlarm->AlarmTime.Hours = (uint8_t)((tmpreg & (RTC_ALRMAR_HT | RTC_ALRMAR_HU)) >> RTC_ALRMAR_HU_Pos);
sAlarm->AlarmTime.Minutes = (uint8_t)((tmpreg & (RTC_ALRMAR_MNT | RTC_ALRMAR_MNU)) >> RTC_ALRMAR_MNU_Pos);
sAlarm->AlarmTime.Seconds = (uint8_t)((tmpreg & (RTC_ALRMAR_ST | RTC_ALRMAR_SU)) >> RTC_ALRMAR_SU_Pos);
sAlarm->AlarmTime.TimeFormat = (uint8_t)((tmpreg & RTC_ALRMAR_PM) >> RTC_ALRMAR_PM_Pos);
sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg;
sAlarm->AlarmDateWeekDay = (uint8_t)((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> RTC_ALRMAR_DU_Pos);
sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMAR_WDSEL);
sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL);
}
else
{
sAlarm->Alarm = RTC_ALARM_B;
tmpreg = READ_REG(RTC->ALRMBR);
subsecondtmpreg = (uint32_t)(READ_REG(RTC->ALRMBSSR) & RTC_ALRMBSSR_SS);
/* Fill the structure with the read parameters */
sAlarm->AlarmTime.Hours = (uint8_t)((tmpreg & (RTC_ALRMBR_HT | RTC_ALRMBR_HU)) >> RTC_ALRMBR_HU_Pos);
sAlarm->AlarmTime.Minutes = (uint8_t)((tmpreg & (RTC_ALRMBR_MNT | RTC_ALRMBR_MNU)) >> RTC_ALRMBR_MNU_Pos);
sAlarm->AlarmTime.Seconds = (uint8_t)((tmpreg & (RTC_ALRMBR_ST | RTC_ALRMBR_SU)) >> RTC_ALRMBR_SU_Pos);
sAlarm->AlarmTime.TimeFormat = (uint8_t)((tmpreg & RTC_ALRMBR_PM) >> RTC_ALRMBR_PM_Pos);
sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg;
sAlarm->AlarmDateWeekDay = (uint8_t)((tmpreg & (RTC_ALRMBR_DT | RTC_ALRMBR_DU)) >> RTC_ALRMBR_DU_Pos);
sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMBR_WDSEL);
sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL);
}
if (Format == RTC_FORMAT_BIN)
{
sAlarm->AlarmTime.Hours = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours);
sAlarm->AlarmTime.Minutes = RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes);
sAlarm->AlarmTime.Seconds = RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds);
sAlarm->AlarmDateWeekDay = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
}
return HAL_OK;
}
/**
* @brief Handle Alarm interrupt request.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef *hrtc)
{
/* Get interrupt status */
uint32_t tmp = READ_REG(RTC->MISR);
if ((tmp & RTC_MISR_ALRAMF) != 0U)
{
/* Clear the AlarmA interrupt pending bit */
WRITE_REG(RTC->SCR, RTC_SCR_CALRAF);
__HAL_RTC_ALARM_EXTI_CLEAR_IT();
#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
/* Call Compare Match registered Callback */
hrtc->AlarmAEventCallback(hrtc);
#else
HAL_RTC_AlarmAEventCallback(hrtc);
#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
}
if ((tmp & RTC_MISR_ALRBMF) != 0U)
{
/* Clear the AlarmB interrupt pending bit */
WRITE_REG(RTC->SCR, RTC_SCR_CALRBF);
__HAL_RTC_ALARM_EXTI_CLEAR_IT();
#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
/* Call Compare Match registered Callback */
hrtc->AlarmBEventCallback(hrtc);
#else
HAL_RTCEx_AlarmBEventCallback(hrtc);
#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
}
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
}
/**
* @brief Alarm A callback.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTC_AlarmAEventCallback could be implemented in the user file
*/
}
/**
* @brief Handle AlarmA Polling request.
* @param hrtc RTC handle
* @param Timeout Timeout duration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
while (READ_BIT(RTC->SR, RTC_SR_ALRAF) == 0U)
{
if (Timeout != HAL_MAX_DELAY)
{
if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
}
/* Clear the Alarm interrupt pending bit */
WRITE_REG(RTC->SCR, RTC_SCR_CALRAF);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup RTC_Exported_Functions_Group4
* @brief Peripheral Control functions
*
@verbatim
===============================================================================
##### Peripheral Control functions #####
===============================================================================
[..]
This subsection provides functions allowing to
(+) Wait for RTC Time and Date Synchronization
@endverbatim
* @{
*/
/**
* @brief Wait until the RTC Time and Date registers (RTC_TR and RTC_DR) are
* synchronized with RTC APB clock.
* @note The RTC Resynchronization mode is write protected, use the
* __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function.
* @note To read the calendar through the shadow registers after Calendar
* initialization, calendar update or after wakeup from low power modes
* the software must first clear the RSF flag.
* The software must then wait until it is set again before reading
* the calendar, which means that the calendar registers have been
* correctly copied into the RTC_TR and RTC_DR shadow registers.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTC_WaitForSynchro(RTC_HandleTypeDef *hrtc)
{
uint32_t tickstart;
UNUSED(hrtc);
/* Clear RSF flag */
CLEAR_BIT(RTC->ICSR, RTC_ICSR_RSF);
tickstart = HAL_GetTick();
/* Wait the registers to be synchronised */
while (READ_BIT(RTC->ICSR, RTC_ICSR_RSF) == 0U)
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
return HAL_TIMEOUT;
}
}
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup RTC_Exported_Functions_Group5
* @brief Peripheral State functions
*
@verbatim
===============================================================================
##### Peripheral State functions #####
===============================================================================
[..]
This subsection provides functions allowing to
(+) Get RTC state
@endverbatim
* @{
*/
/**
* @brief Return the RTC handle state.
* @param hrtc RTC handle
* @retval HAL state
*/
HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef *hrtc)
{
/* Return RTC handle state */
return hrtc->State;
}
/**
* @}
*/
/**
* @}
*/
/** @addtogroup RTC_Private_Functions
* @{
*/
/**
* @brief Enter the RTC Initialization mode.
* @note The RTC Initialization mode is write protected, use the
* __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef RTC_EnterInitMode(RTC_HandleTypeDef *hrtc)
{
uint32_t tickstart;
HAL_StatusTypeDef status = HAL_OK;
UNUSED(hrtc);
/* Check if the Initialization mode is set */
if (READ_BIT(RTC->ICSR, RTC_ICSR_INITF) == 0U)
{
/* Set the Initialization mode */
SET_BIT(RTC->ICSR, RTC_ICSR_INIT);
tickstart = HAL_GetTick();
/* Wait till RTC is in INIT state and if Time out is reached exit */
while ((READ_BIT(RTC->ICSR, RTC_ICSR_INITF) == 0U) && (status != HAL_TIMEOUT))
{
if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
{
status = HAL_TIMEOUT;
hrtc->State = HAL_RTC_STATE_TIMEOUT;
}
}
}
return status;
}
/**
* @brief Exit the RTC Initialization mode.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef RTC_ExitInitMode(RTC_HandleTypeDef *hrtc)
{
HAL_StatusTypeDef status = HAL_OK;
/* Exit Initialization mode */
CLEAR_BIT(RTC->ICSR, RTC_ICSR_INIT);
/* If CR_BYPSHAD bit = 0, wait for synchro */
if (READ_BIT(RTC->CR, RTC_CR_BYPSHAD) == 0U)
{
if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
status = HAL_TIMEOUT;
}
}
else /* WA 2.9.6 Calendar initialization may fail in case of consecutive INIT mode entry */
{
/* Clear BYPSHAD bit */
CLEAR_BIT(RTC->CR, RTC_CR_BYPSHAD);
if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
status = HAL_TIMEOUT;
}
/* Restore BYPSHAD bit */
SET_BIT(RTC->CR, RTC_CR_BYPSHAD);
}
return status;
}
/**
* @brief Convert a 2 digit decimal to BCD format.
* @param Value Byte to be converted
* @retval Converted byte
*/
uint8_t RTC_ByteToBcd2(uint8_t Value)
{
uint32_t bcdhigh = 0U;
uint8_t tmp_Value = Value;
while (tmp_Value >= 10U)
{
bcdhigh++;
tmp_Value -= 10U;
}
return ((uint8_t)(bcdhigh << 4U) | tmp_Value);
}
/**
* @brief Convert from 2 digit BCD to Binary.
* @param Value BCD value to be converted
* @retval Converted word
*/
uint8_t RTC_Bcd2ToByte(uint8_t Value)
{
uint32_t tmp;
tmp = (((uint32_t)Value & 0xF0U) >> 4) * 10U;
return (uint8_t)(tmp + ((uint32_t)Value & 0x0FU));
}
/**
* @brief Daylight Saving Time, Add one hour to the calendar in one single operation
* without going through the initialization procedure.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTC_DST_Add1Hour(RTC_HandleTypeDef *hrtc)
{
UNUSED(hrtc);
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
SET_BIT(RTC->CR, RTC_CR_ADD1H);
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
}
/**
* @brief Daylight Saving Time, Subtract one hour from the calendar in one
* single operation without going through the initialization procedure.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTC_DST_Sub1Hour(RTC_HandleTypeDef *hrtc)
{
UNUSED(hrtc);
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
SET_BIT(RTC->CR, RTC_CR_SUB1H);
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
}
/**
* @brief Daylight Saving Time, Set the store operation bit.
* @note It can be used by the software in order to memorize the DST status.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTC_DST_SetStoreOperation(RTC_HandleTypeDef *hrtc)
{
UNUSED(hrtc);
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
SET_BIT(RTC->CR, RTC_CR_BKP);
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
}
/**
* @brief Daylight Saving Time, Clear the store operation bit.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTC_DST_ClearStoreOperation(RTC_HandleTypeDef *hrtc)
{
UNUSED(hrtc);
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
CLEAR_BIT(RTC->CR, RTC_CR_BKP);
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
}
/**
* @brief Daylight Saving Time, Read the store operation bit.
* @param hrtc RTC handle
* @retval operation see RTC_StoreOperation_Definitions
*/
uint32_t HAL_RTC_DST_ReadStoreOperation(RTC_HandleTypeDef *hrtc)
{
UNUSED(hrtc);
return READ_BIT(RTC->CR, RTC_CR_BKP);
}
/**
* @}
*/
#endif /* HAL_RTC_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/