blob: 6e0ac9e3dbce05df6c67d8a388579c449eb6d4ab [file] [log] [blame]
/**
******************************************************************************
* @file stm32g4xx_hal_pwr_ex.h
* @author MCD Application Team
* @brief Header file of PWR HAL Extended module.
******************************************************************************
* @attention
*
* <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32G4xx_HAL_PWR_EX_H
#define STM32G4xx_HAL_PWR_EX_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32g4xx_hal_def.h"
/** @addtogroup STM32G4xx_HAL_Driver
* @{
*/
/** @addtogroup PWREx
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup PWREx_Exported_Types PWR Extended Exported Types
* @{
*/
/**
* @brief PWR PVM configuration structure definition
*/
typedef struct
{
uint32_t PVMType; /*!< PVMType: Specifies which voltage is monitored and against which threshold.
This parameter can be a value of @ref PWREx_PVM_Type. */
uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins.
This parameter can be a value of @ref PWREx_PVM_Mode. */
}PWR_PVMTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup PWREx_Exported_Constants PWR Extended Exported Constants
* @{
*/
/** @defgroup PWREx_WUP_Polarity Shift to apply to retrieve polarity information from PWR_WAKEUP_PINy_xxx constants
* @{
*/
#define PWR_WUP_POLARITY_SHIFT 0x05U /*!< Internal constant used to retrieve wakeup pin polariry */
/**
* @}
*/
/** @defgroup PWREx_WakeUp_Pins PWR wake-up pins
* @{
*/
#define PWR_WAKEUP_PIN1 PWR_CR3_EWUP1 /*!< Wakeup pin 1 (with high level polarity) */
#define PWR_WAKEUP_PIN2 PWR_CR3_EWUP2 /*!< Wakeup pin 2 (with high level polarity) */
#define PWR_WAKEUP_PIN3 PWR_CR3_EWUP3 /*!< Wakeup pin 3 (with high level polarity) */
#define PWR_WAKEUP_PIN4 PWR_CR3_EWUP4 /*!< Wakeup pin 4 (with high level polarity) */
#define PWR_WAKEUP_PIN5 PWR_CR3_EWUP5 /*!< Wakeup pin 5 (with high level polarity) */
#define PWR_WAKEUP_PIN1_HIGH PWR_CR3_EWUP1 /*!< Wakeup pin 1 (with high level polarity) */
#define PWR_WAKEUP_PIN2_HIGH PWR_CR3_EWUP2 /*!< Wakeup pin 2 (with high level polarity) */
#define PWR_WAKEUP_PIN3_HIGH PWR_CR3_EWUP3 /*!< Wakeup pin 3 (with high level polarity) */
#define PWR_WAKEUP_PIN4_HIGH PWR_CR3_EWUP4 /*!< Wakeup pin 4 (with high level polarity) */
#define PWR_WAKEUP_PIN5_HIGH PWR_CR3_EWUP5 /*!< Wakeup pin 5 (with high level polarity) */
#define PWR_WAKEUP_PIN1_LOW (uint32_t)((PWR_CR4_WP1<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP1) /*!< Wakeup pin 1 (with low level polarity) */
#define PWR_WAKEUP_PIN2_LOW (uint32_t)((PWR_CR4_WP2<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP2) /*!< Wakeup pin 2 (with low level polarity) */
#define PWR_WAKEUP_PIN3_LOW (uint32_t)((PWR_CR4_WP3<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP3) /*!< Wakeup pin 3 (with low level polarity) */
#define PWR_WAKEUP_PIN4_LOW (uint32_t)((PWR_CR4_WP4<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP4) /*!< Wakeup pin 4 (with low level polarity) */
#define PWR_WAKEUP_PIN5_LOW (uint32_t)((PWR_CR4_WP5<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP5) /*!< Wakeup pin 5 (with low level polarity) */
/**
* @}
*/
/** @defgroup PWREx_PVM_Type Peripheral Voltage Monitoring type
* @{
*/
#if defined(PWR_CR2_PVME1)
#define PWR_PVM_1 PWR_CR2_PVME1 /*!< Peripheral Voltage Monitoring 1 enable: VDDUSB versus 1.2 V (applicable when USB feature is supported) */
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
#define PWR_PVM_2 PWR_CR2_PVME2 /*!< Peripheral Voltage Monitoring 2 enable: VDDIO2 versus 0.9 V (applicable when VDDIO2 is present on device) */
#endif /* PWR_CR2_PVME2 */
#define PWR_PVM_3 PWR_CR2_PVME3 /*!< Peripheral Voltage Monitoring 3 enable: VDDA versus 1.62 V */
#define PWR_PVM_4 PWR_CR2_PVME4 /*!< Peripheral Voltage Monitoring 4 enable: VDDA versus 2.2 V */
/**
* @}
*/
/** @defgroup PWREx_PVM_Mode PWR PVM interrupt and event mode
* @{
*/
#define PWR_PVM_MODE_NORMAL 0x00000000U /*!< basic mode is used */
#define PWR_PVM_MODE_IT_RISING 0x00010001U /*!< External Interrupt Mode with Rising edge trigger detection */
#define PWR_PVM_MODE_IT_FALLING 0x00010002U /*!< External Interrupt Mode with Falling edge trigger detection */
#define PWR_PVM_MODE_IT_RISING_FALLING 0x00010003U /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define PWR_PVM_MODE_EVENT_RISING 0x00020001U /*!< Event Mode with Rising edge trigger detection */
#define PWR_PVM_MODE_EVENT_FALLING 0x00020002U /*!< Event Mode with Falling edge trigger detection */
#define PWR_PVM_MODE_EVENT_RISING_FALLING 0x00020003U /*!< Event Mode with Rising/Falling edge trigger detection */
/**
* @}
*/
/** @defgroup PWREx_Regulator_Voltage_Scale PWR Regulator voltage scale
* @{
*/
#if defined(PWR_CR5_R1MODE)
#define PWR_REGULATOR_VOLTAGE_SCALE1_BOOST ((uint32_t)0x00000000) /*!< Voltage scaling range 1 boost mode */
#endif /*PWR_CR5_R1MODE */
#define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR1_VOS_0 /*!< Voltage scaling range 1 normal mode */
#define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR1_VOS_1 /*!< Voltage scaling range 2 */
/**
* @}
*/
/** @defgroup PWREx_VBAT_Battery_Charging_Selection PWR battery charging resistor selection
* @{
*/
#define PWR_BATTERY_CHARGING_RESISTOR_5 0x00000000U /*!< VBAT charging through a 5 kOhms resistor */
#define PWR_BATTERY_CHARGING_RESISTOR_1_5 PWR_CR4_VBRS /*!< VBAT charging through a 1.5 kOhms resistor */
/**
* @}
*/
/** @defgroup PWREx_VBAT_Battery_Charging PWR battery charging
* @{
*/
#define PWR_BATTERY_CHARGING_DISABLE 0x00000000U
#define PWR_BATTERY_CHARGING_ENABLE PWR_CR4_VBE
/**
* @}
*/
/** @defgroup PWREx_GPIO_Bit_Number GPIO bit number for I/O setting in standby/shutdown mode
* @{
*/
#define PWR_GPIO_BIT_0 PWR_PUCRA_PA0 /*!< GPIO port I/O pin 0 */
#define PWR_GPIO_BIT_1 PWR_PUCRA_PA1 /*!< GPIO port I/O pin 1 */
#define PWR_GPIO_BIT_2 PWR_PUCRA_PA2 /*!< GPIO port I/O pin 2 */
#define PWR_GPIO_BIT_3 PWR_PUCRA_PA3 /*!< GPIO port I/O pin 3 */
#define PWR_GPIO_BIT_4 PWR_PUCRA_PA4 /*!< GPIO port I/O pin 4 */
#define PWR_GPIO_BIT_5 PWR_PUCRA_PA5 /*!< GPIO port I/O pin 5 */
#define PWR_GPIO_BIT_6 PWR_PUCRA_PA6 /*!< GPIO port I/O pin 6 */
#define PWR_GPIO_BIT_7 PWR_PUCRA_PA7 /*!< GPIO port I/O pin 7 */
#define PWR_GPIO_BIT_8 PWR_PUCRA_PA8 /*!< GPIO port I/O pin 8 */
#define PWR_GPIO_BIT_9 PWR_PUCRA_PA9 /*!< GPIO port I/O pin 9 */
#define PWR_GPIO_BIT_10 PWR_PUCRA_PA10 /*!< GPIO port I/O pin 10 */
#define PWR_GPIO_BIT_11 PWR_PUCRA_PA11 /*!< GPIO port I/O pin 11 */
#define PWR_GPIO_BIT_12 PWR_PUCRA_PA12 /*!< GPIO port I/O pin 12 */
#define PWR_GPIO_BIT_13 PWR_PUCRA_PA13 /*!< GPIO port I/O pin 13 */
#define PWR_GPIO_BIT_14 PWR_PDCRA_PA14 /*!< GPIO port I/O pin 14 */
#define PWR_GPIO_BIT_15 PWR_PUCRA_PA15 /*!< GPIO port I/O pin 15 */
/**
* @}
*/
/** @defgroup PWREx_GPIO GPIO port
* @{
*/
#define PWR_GPIO_A 0x00000000U /*!< GPIO port A */
#define PWR_GPIO_B 0x00000001U /*!< GPIO port B */
#define PWR_GPIO_C 0x00000002U /*!< GPIO port C */
#define PWR_GPIO_D 0x00000003U /*!< GPIO port D */
#define PWR_GPIO_E 0x00000004U /*!< GPIO port E */
#define PWR_GPIO_F 0x00000005U /*!< GPIO port F */
#define PWR_GPIO_G 0x00000006U /*!< GPIO port G */
/**
* @}
*/
/** @defgroup PWREx_PVM_EXTI_LINE PWR PVM external interrupts lines
* @{
*/
#if defined(PWR_CR2_PVME1)
#define PWR_EXTI_LINE_PVM1 0x00000008U /*!< External interrupt line 35 Connected to the PVM1 EXTI Line */
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
#define PWR_EXTI_LINE_PVM2 0x00000010U /*!< External interrupt line 36 Connected to the PVM2 EXTI Line */
#endif /* PWR_CR2_PVME2 */
#define PWR_EXTI_LINE_PVM3 0x00000020U /*!< External interrupt line 37 Connected to the PVM3 EXTI Line */
#define PWR_EXTI_LINE_PVM4 0x00000040U /*!< External interrupt line 38 Connected to the PVM4 EXTI Line */
/**
* @}
*/
/** @defgroup PWREx_PVM_EVENT_LINE PWR PVM event lines
* @{
*/
#if defined(PWR_CR2_PVME1)
#define PWR_EVENT_LINE_PVM1 0x00000008U /*!< Event line 35 Connected to the PVM1 EXTI Line */
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
#define PWR_EVENT_LINE_PVM2 0x00000010U /*!< Event line 36 Connected to the PVM2 EXTI Line */
#endif /* PWR_CR2_PVME2 */
#define PWR_EVENT_LINE_PVM3 0x00000020U /*!< Event line 37 Connected to the PVM3 EXTI Line */
#define PWR_EVENT_LINE_PVM4 0x00000040U /*!< Event line 38 Connected to the PVM4 EXTI Line */
/**
* @}
*/
/** @defgroup PWREx_Flag PWR Status Flags
* Elements values convention: 0000 0000 0XXY YYYYb
* - Y YYYY : Flag position in the XX register (5 bits)
* - XX : Status register (2 bits)
* - 01: SR1 register
* - 10: SR2 register
* The only exception is PWR_FLAG_WU, encompassing all
* wake-up flags and set to PWR_SR1_WUF.
* @{
*/
#define PWR_FLAG_WUF1 0x0020U /*!< Wakeup event on wakeup pin 1 */
#define PWR_FLAG_WUF2 0x0021U /*!< Wakeup event on wakeup pin 2 */
#define PWR_FLAG_WUF3 0x0022U /*!< Wakeup event on wakeup pin 3 */
#define PWR_FLAG_WUF4 0x0023U /*!< Wakeup event on wakeup pin 4 */
#define PWR_FLAG_WUF5 0x0024U /*!< Wakeup event on wakeup pin 5 */
#define PWR_FLAG_WU PWR_SR1_WUF /*!< Encompass wakeup event on all wakeup pins */
#define PWR_FLAG_SB 0x0028U /*!< Standby flag */
#define PWR_FLAG_WUFI 0x002FU /*!< Wakeup on internal wakeup line */
#define PWR_FLAG_REGLPS 0x0048U /*!< Low-power regulator start flag */
#define PWR_FLAG_REGLPF 0x0049U /*!< Low-power regulator flag */
#define PWR_FLAG_VOSF 0x004AU /*!< Voltage scaling flag */
#define PWR_FLAG_PVDO 0x004BU /*!< Power Voltage Detector output flag */
#if defined(PWR_CR2_PVME1)
#define PWR_FLAG_PVMO1 0x004CU /*!< Power Voltage Monitoring 1 output flag */
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
#define PWR_FLAG_PVMO2 0x004DU /*!< Power Voltage Monitoring 2 output flag */
#endif /* PWR_CR2_PVME2 */
#define PWR_FLAG_PVMO3 0x004EU /*!< Power Voltage Monitoring 3 output flag */
#define PWR_FLAG_PVMO4 0x004FU /*!< Power Voltage Monitoring 4 output flag */
/**
* @}
*/
/**
* @}
*/
/* Exported macros -----------------------------------------------------------*/
/** @defgroup PWREx_Exported_Macros PWR Extended Exported Macros
* @{
*/
#if defined(PWR_CR2_PVME1)
/**
* @brief Enable the PVM1 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM1)
/**
* @brief Disable the PVM1 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM1)
/**
* @brief Enable the PVM1 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM1)
/**
* @brief Disable the PVM1 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM1)
/**
* @brief Enable the PVM1 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM1)
/**
* @brief Disable the PVM1 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM1)
/**
* @brief Enable the PVM1 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM1)
/**
* @brief Disable the PVM1 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM1)
/**
* @brief PVM1 EXTI line configuration: set rising & falling edge trigger.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_ENABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM1_EXTI_ENABLE_RISING_EDGE(); \
__HAL_PWR_PVM1_EXTI_ENABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Disable the PVM1 Extended Interrupt Rising & Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_DISABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM1_EXTI_DISABLE_RISING_EDGE(); \
__HAL_PWR_PVM1_EXTI_DISABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Generate a Software interrupt on selected EXTI line.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM1)
/**
* @brief Check whether the specified PVM1 EXTI interrupt flag is set or not.
* @retval EXTI PVM1 Line Status.
*/
#define __HAL_PWR_PVM1_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM1)
/**
* @brief Clear the PVM1 EXTI flag.
* @retval None
*/
#define __HAL_PWR_PVM1_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM1)
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
/**
* @brief Enable the PVM2 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM2)
/**
* @brief Disable the PVM2 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM2)
/**
* @brief Enable the PVM2 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM2)
/**
* @brief Disable the PVM2 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM2)
/**
* @brief Enable the PVM2 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM2)
/**
* @brief Disable the PVM2 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM2)
/**
* @brief Enable the PVM2 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM2)
/**
* @brief Disable the PVM2 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM2)
/**
* @brief PVM2 EXTI line configuration: set rising & falling edge trigger.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_ENABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM2_EXTI_ENABLE_RISING_EDGE(); \
__HAL_PWR_PVM2_EXTI_ENABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Disable the PVM2 Extended Interrupt Rising & Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_DISABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM2_EXTI_DISABLE_RISING_EDGE(); \
__HAL_PWR_PVM2_EXTI_DISABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Generate a Software interrupt on selected EXTI line.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM2)
/**
* @brief Check whether the specified PVM2 EXTI interrupt flag is set or not.
* @retval EXTI PVM2 Line Status.
*/
#define __HAL_PWR_PVM2_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM2)
/**
* @brief Clear the PVM2 EXTI flag.
* @retval None
*/
#define __HAL_PWR_PVM2_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM2)
#endif /* PWR_CR2_PVME2 */
/**
* @brief Enable the PVM3 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM3)
/**
* @brief Disable the PVM3 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM3)
/**
* @brief Enable the PVM3 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM3)
/**
* @brief Disable the PVM3 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM3)
/**
* @brief Enable the PVM3 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM3)
/**
* @brief Disable the PVM3 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM3)
/**
* @brief Enable the PVM3 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM3)
/**
* @brief Disable the PVM3 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM3)
/**
* @brief PVM3 EXTI line configuration: set rising & falling edge trigger.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_ENABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM3_EXTI_ENABLE_RISING_EDGE(); \
__HAL_PWR_PVM3_EXTI_ENABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Disable the PVM3 Extended Interrupt Rising & Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_DISABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM3_EXTI_DISABLE_RISING_EDGE(); \
__HAL_PWR_PVM3_EXTI_DISABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Generate a Software interrupt on selected EXTI line.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM3)
/**
* @brief Check whether the specified PVM3 EXTI interrupt flag is set or not.
* @retval EXTI PVM3 Line Status.
*/
#define __HAL_PWR_PVM3_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM3)
/**
* @brief Clear the PVM3 EXTI flag.
* @retval None
*/
#define __HAL_PWR_PVM3_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM3)
/**
* @brief Enable the PVM4 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM4)
/**
* @brief Disable the PVM4 Extended Interrupt Line.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM4)
/**
* @brief Enable the PVM4 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM4)
/**
* @brief Disable the PVM4 Event Line.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM4)
/**
* @brief Enable the PVM4 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM4)
/**
* @brief Disable the PVM4 Extended Interrupt Rising Trigger.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM4)
/**
* @brief Enable the PVM4 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM4)
/**
* @brief Disable the PVM4 Extended Interrupt Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM4)
/**
* @brief PVM4 EXTI line configuration: set rising & falling edge trigger.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_ENABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM4_EXTI_ENABLE_RISING_EDGE(); \
__HAL_PWR_PVM4_EXTI_ENABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Disable the PVM4 Extended Interrupt Rising & Falling Trigger.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_DISABLE_RISING_FALLING_EDGE() \
do { \
__HAL_PWR_PVM4_EXTI_DISABLE_RISING_EDGE(); \
__HAL_PWR_PVM4_EXTI_DISABLE_FALLING_EDGE(); \
} while(0)
/**
* @brief Generate a Software interrupt on selected EXTI line.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM4)
/**
* @brief Check whether or not the specified PVM4 EXTI interrupt flag is set.
* @retval EXTI PVM4 Line Status.
*/
#define __HAL_PWR_PVM4_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM4)
/**
* @brief Clear the PVM4 EXTI flag.
* @retval None
*/
#define __HAL_PWR_PVM4_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM4)
/**
* @brief Configure the main internal regulator output voltage.
* @param __REGULATOR__: specifies the regulator output voltage to achieve
* a tradeoff between performance and power consumption.
* This parameter can be one of the following values:
* @arg @ref PWR_REGULATOR_VOLTAGE_SCALE1_BOOST Regulator voltage output range 1 mode,
* typical output voltage at 1.28 V,
* system frequency up to 170 MHz.
* @arg @ref PWR_REGULATOR_VOLTAGE_SCALE1 Regulator voltage output range 1 mode,
* typical output voltage at 1.2 V,
* system frequency up to 150 MHz.
* @arg @ref PWR_REGULATOR_VOLTAGE_SCALE2 Regulator voltage output range 2 mode,
* typical output voltage at 1.0 V,
* system frequency up to 26 MHz.
* @note This macro is similar to HAL_PWREx_ControlVoltageScaling() API but doesn't check
* whether or not VOSF flag is cleared when moving from range 2 to range 1. User
* may resort to __HAL_PWR_GET_FLAG() macro to check VOSF bit resetting.
* @retval None
*/
#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \
__IO uint32_t tmpreg; \
MODIFY_REG(PWR->CR1, PWR_CR1_VOS, (__REGULATOR__)); \
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(PWR->CR1, PWR_CR1_VOS); \
UNUSED(tmpreg); \
} while(0)
/**
* @}
*/
/* Private macros --------------------------------------------------------*/
/** @addtogroup PWREx_Private_Macros PWR Extended Private Macros
* @{
*/
#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
((PIN) == PWR_WAKEUP_PIN2) || \
((PIN) == PWR_WAKEUP_PIN3) || \
((PIN) == PWR_WAKEUP_PIN4) || \
((PIN) == PWR_WAKEUP_PIN5) || \
((PIN) == PWR_WAKEUP_PIN1_HIGH) || \
((PIN) == PWR_WAKEUP_PIN2_HIGH) || \
((PIN) == PWR_WAKEUP_PIN3_HIGH) || \
((PIN) == PWR_WAKEUP_PIN4_HIGH) || \
((PIN) == PWR_WAKEUP_PIN5_HIGH) || \
((PIN) == PWR_WAKEUP_PIN1_LOW) || \
((PIN) == PWR_WAKEUP_PIN2_LOW) || \
((PIN) == PWR_WAKEUP_PIN3_LOW) || \
((PIN) == PWR_WAKEUP_PIN4_LOW) || \
((PIN) == PWR_WAKEUP_PIN5_LOW))
#define IS_PWR_PVM_TYPE(TYPE) (((TYPE) == PWR_PVM_1) ||\
((TYPE) == PWR_PVM_2) ||\
((TYPE) == PWR_PVM_3) ||\
((TYPE) == PWR_PVM_4))
#define IS_PWR_PVM_MODE(MODE) (((MODE) == PWR_PVM_MODE_NORMAL) ||\
((MODE) == PWR_PVM_MODE_IT_RISING) ||\
((MODE) == PWR_PVM_MODE_IT_FALLING) ||\
((MODE) == PWR_PVM_MODE_IT_RISING_FALLING) ||\
((MODE) == PWR_PVM_MODE_EVENT_RISING) ||\
((MODE) == PWR_PVM_MODE_EVENT_FALLING) ||\
((MODE) == PWR_PVM_MODE_EVENT_RISING_FALLING))
#if defined(PWR_CR5_R1MODE)
#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1_BOOST) || \
((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2))
#else
#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2))
#endif
#define IS_PWR_BATTERY_RESISTOR_SELECT(RESISTOR) (((RESISTOR) == PWR_BATTERY_CHARGING_RESISTOR_5) ||\
((RESISTOR) == PWR_BATTERY_CHARGING_RESISTOR_1_5))
#define IS_PWR_BATTERY_CHARGING(CHARGING) (((CHARGING) == PWR_BATTERY_CHARGING_DISABLE) ||\
((CHARGING) == PWR_BATTERY_CHARGING_ENABLE))
#define IS_PWR_GPIO_BIT_NUMBER(BIT_NUMBER) (((BIT_NUMBER) & GPIO_PIN_MASK) != (uint32_t)0x00U)
#define IS_PWR_GPIO(GPIO) (((GPIO) == PWR_GPIO_A) ||\
((GPIO) == PWR_GPIO_B) ||\
((GPIO) == PWR_GPIO_C) ||\
((GPIO) == PWR_GPIO_D) ||\
((GPIO) == PWR_GPIO_E) ||\
((GPIO) == PWR_GPIO_F) ||\
((GPIO) == PWR_GPIO_G))
/**
* @}
*/
/** @addtogroup PWREx_Exported_Functions PWR Extended Exported Functions
* @{
*/
/** @addtogroup PWREx_Exported_Functions_Group1 Extended Peripheral Control functions
* @{
*/
/* Peripheral Control functions **********************************************/
uint32_t HAL_PWREx_GetVoltageRange(void);
HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling);
void HAL_PWREx_EnableBatteryCharging(uint32_t ResistorSelection);
void HAL_PWREx_DisableBatteryCharging(void);
void HAL_PWREx_EnableInternalWakeUpLine(void);
void HAL_PWREx_DisableInternalWakeUpLine(void);
HAL_StatusTypeDef HAL_PWREx_EnableGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber);
HAL_StatusTypeDef HAL_PWREx_DisableGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber);
HAL_StatusTypeDef HAL_PWREx_EnableGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber);
HAL_StatusTypeDef HAL_PWREx_DisableGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber);
void HAL_PWREx_EnablePullUpPullDownConfig(void);
void HAL_PWREx_DisablePullUpPullDownConfig(void);
void HAL_PWREx_EnableSRAM2ContentRetention(void);
void HAL_PWREx_DisableSRAM2ContentRetention(void);
#if defined(PWR_CR2_PVME1)
void HAL_PWREx_EnablePVM1(void);
void HAL_PWREx_DisablePVM1(void);
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
void HAL_PWREx_EnablePVM2(void);
void HAL_PWREx_DisablePVM2(void);
#endif /* PWR_CR2_PVME2 */
void HAL_PWREx_EnablePVM3(void);
void HAL_PWREx_DisablePVM3(void);
void HAL_PWREx_EnablePVM4(void);
void HAL_PWREx_DisablePVM4(void);
HAL_StatusTypeDef HAL_PWREx_ConfigPVM(PWR_PVMTypeDef *sConfigPVM);
#if defined(PWR_CR3_UCPD_DBDIS)
void HAL_PWREx_EnableUSBDeadBatteryPD(void);
void HAL_PWREx_DisableUSBDeadBatteryPD(void);
#endif /* PWR_CR3_UCPD_DBDIS */
#if defined(PWR_CR3_UCPD_STDBY)
void HAL_PWREx_EnableUSBStandByModePD(void);
void HAL_PWREx_DisableUSBStandByModePD (void);
#endif /* PWR_CR3_UCPD_STDBY */
/* Low Power modes configuration functions ************************************/
void HAL_PWREx_EnableLowPowerRunMode(void);
HAL_StatusTypeDef HAL_PWREx_DisableLowPowerRunMode(void);
void HAL_PWREx_EnterSTOP0Mode(uint8_t STOPEntry);
void HAL_PWREx_EnterSTOP1Mode(uint8_t STOPEntry);
void HAL_PWREx_EnterSHUTDOWNMode(void);
void HAL_PWREx_PVD_PVM_IRQHandler(void);
#if defined(PWR_CR2_PVME1)
void HAL_PWREx_PVM1Callback(void);
#endif /* PWR_CR2_PVME1 */
#if defined(PWR_CR2_PVME2)
void HAL_PWREx_PVM2Callback(void);
#endif /* PWR_CR2_PVME2 */
void HAL_PWREx_PVM3Callback(void);
void HAL_PWREx_PVM4Callback(void);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32G4xx_HAL_PWR_EX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/