| /** |
| ****************************************************************************** |
| * @file stm32g4xx_ll_pwr.h |
| * @author MCD Application Team |
| * @brief Header file of PWR LL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32G4xx_LL_PWR_H |
| #define STM32G4xx_LL_PWR_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32g4xx.h" |
| |
| /** @addtogroup STM32G4xx_LL_Driver |
| * @{ |
| */ |
| |
| #if defined(PWR) |
| |
| /** @defgroup PWR_LL PWR |
| * @{ |
| */ |
| |
| /* Private types -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| |
| /* Private constants ---------------------------------------------------------*/ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup PWR_LL_Exported_Constants PWR Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup PWR_LL_EC_CLEAR_FLAG Clear Flags Defines |
| * @brief Flags defines which can be used with LL_PWR_WriteReg function |
| * @{ |
| */ |
| #define LL_PWR_SCR_CSBF PWR_SCR_CSBF |
| #define LL_PWR_SCR_CWUF PWR_SCR_CWUF |
| #define LL_PWR_SCR_CWUF5 PWR_SCR_CWUF5 |
| #define LL_PWR_SCR_CWUF4 PWR_SCR_CWUF4 |
| #define LL_PWR_SCR_CWUF3 PWR_SCR_CWUF3 |
| #define LL_PWR_SCR_CWUF2 PWR_SCR_CWUF2 |
| #define LL_PWR_SCR_CWUF1 PWR_SCR_CWUF1 |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_GET_FLAG Get Flags Defines |
| * @brief Flags defines which can be used with LL_PWR_ReadReg function |
| * @{ |
| */ |
| #define LL_PWR_SR1_WUFI PWR_SR1_WUFI |
| #define LL_PWR_SR1_SBF PWR_SR1_SBF |
| #define LL_PWR_SR1_WUF5 PWR_SR1_WUF5 |
| #define LL_PWR_SR1_WUF4 PWR_SR1_WUF4 |
| #define LL_PWR_SR1_WUF3 PWR_SR1_WUF3 |
| #define LL_PWR_SR1_WUF2 PWR_SR1_WUF2 |
| #define LL_PWR_SR1_WUF1 PWR_SR1_WUF1 |
| #if defined(PWR_SR2_PVMO4) |
| #define LL_PWR_SR2_PVMO4 PWR_SR2_PVMO4 |
| #endif /* PWR_SR2_PVMO4 */ |
| #if defined(PWR_SR2_PVMO3) |
| #define LL_PWR_SR2_PVMO3 PWR_SR2_PVMO3 |
| #endif /* PWR_SR2_PVMO3 */ |
| #if defined(PWR_SR2_PVMO2) |
| #define LL_PWR_SR2_PVMO2 PWR_SR2_PVMO2 |
| #endif /* PWR_SR2_PVMO2 */ |
| #if defined(PWR_SR2_PVMO1) |
| #define LL_PWR_SR2_PVMO1 PWR_SR2_PVMO1 |
| #endif /* PWR_SR2_PVMO1 */ |
| #define LL_PWR_SR2_PVDO PWR_SR2_PVDO |
| #define LL_PWR_SR2_VOSF PWR_SR2_VOSF |
| #define LL_PWR_SR2_REGLPF PWR_SR2_REGLPF |
| #define LL_PWR_SR2_REGLPS PWR_SR2_REGLPS |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_REGU_VOLTAGE REGU VOLTAGE |
| * @{ |
| */ |
| #define LL_PWR_REGU_VOLTAGE_SCALE1 (PWR_CR1_VOS_0) |
| #define LL_PWR_REGU_VOLTAGE_SCALE2 (PWR_CR1_VOS_1) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_MODE_PWR MODE PWR |
| * @{ |
| */ |
| #define LL_PWR_MODE_STOP0 (PWR_CR1_LPMS_STOP0) |
| #define LL_PWR_MODE_STOP1 (PWR_CR1_LPMS_STOP1) |
| #define LL_PWR_MODE_STANDBY (PWR_CR1_LPMS_STANDBY) |
| #define LL_PWR_MODE_SHUTDOWN (PWR_CR1_LPMS_SHUTDOWN) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_PVM_VDDUSB_1 Peripheral voltage monitoring |
| * @{ |
| */ |
| #if defined(PWR_CR2_PVME1) |
| #define LL_PWR_PVM_VDDA_COMP (PWR_CR2_PVME1) /* Monitoring VDDA vs. x.xV */ |
| #endif |
| #if defined(PWR_CR2_PVME2) |
| #define LL_PWR_PVM_VDDA_FASTDAC (PWR_CR2_PVME2) /* Monitoring VDDA vs. x.xV */ |
| #endif |
| #if defined(PWR_CR2_PVME3) |
| #define LL_PWR_PVM_VDDA_ADC (PWR_CR2_PVME3) /* Monitoring VDDA vs. 1.62V */ |
| #endif |
| #if defined(PWR_CR2_PVME4) |
| #define LL_PWR_PVM_VDDA_OPAMP_DAC (PWR_CR2_PVME4) /* Monitoring VDDA vs. 1x.xV */ |
| #endif |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_PVDLEVEL PVDLEVEL |
| * @{ |
| */ |
| #define LL_PWR_PVDLEVEL_0 (PWR_CR2_PLS_LEV0) /* VPVD0 around 2.0 V */ |
| #define LL_PWR_PVDLEVEL_1 (PWR_CR2_PLS_LEV1) /* VPVD1 around 2.2 V */ |
| #define LL_PWR_PVDLEVEL_2 (PWR_CR2_PLS_LEV2) /* VPVD2 around 2.4 V */ |
| #define LL_PWR_PVDLEVEL_3 (PWR_CR2_PLS_LEV3) /* VPVD3 around 2.5 V */ |
| #define LL_PWR_PVDLEVEL_4 (PWR_CR2_PLS_LEV4) /* VPVD4 around 2.6 V */ |
| #define LL_PWR_PVDLEVEL_5 (PWR_CR2_PLS_LEV5) /* VPVD5 around 2.8 V */ |
| #define LL_PWR_PVDLEVEL_6 (PWR_CR2_PLS_LEV6) /* VPVD6 around 2.9 V */ |
| #define LL_PWR_PVDLEVEL_7 (PWR_CR2_PLS_LEV7) /* External input analog voltage (Compare internally to VREFINT) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_WAKEUP WAKEUP |
| * @{ |
| */ |
| #define LL_PWR_WAKEUP_PIN1 (PWR_CR3_EWUP1) |
| #define LL_PWR_WAKEUP_PIN2 (PWR_CR3_EWUP2) |
| #define LL_PWR_WAKEUP_PIN3 (PWR_CR3_EWUP3) |
| #define LL_PWR_WAKEUP_PIN4 (PWR_CR3_EWUP4) |
| #define LL_PWR_WAKEUP_PIN5 (PWR_CR3_EWUP5) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_BATT_CHARG_RESISTOR BATT CHARG RESISTOR |
| * @{ |
| */ |
| #define LL_PWR_BATT_CHARG_RESISTOR_5K ((uint32_t)0x00000000) |
| #define LL_PWR_BATT_CHARGRESISTOR_1_5K (PWR_CR4_VBRS) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_GPIO GPIO |
| * @{ |
| */ |
| #define LL_PWR_GPIO_A ((uint32_t)(&(PWR->PUCRA))) |
| #define LL_PWR_GPIO_B ((uint32_t)(&(PWR->PUCRB))) |
| #define LL_PWR_GPIO_C ((uint32_t)(&(PWR->PUCRC))) |
| #define LL_PWR_GPIO_D ((uint32_t)(&(PWR->PUCRD))) |
| #define LL_PWR_GPIO_E ((uint32_t)(&(PWR->PUCRE))) |
| #define LL_PWR_GPIO_F ((uint32_t)(&(PWR->PUCRF))) |
| #define LL_PWR_GPIO_G ((uint32_t)(&(PWR->PUCRG))) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EC_GPIO_BIT GPIO BIT |
| * @{ |
| */ |
| #define LL_PWR_GPIO_BIT_0 ((uint32_t)0x00000001) |
| #define LL_PWR_GPIO_BIT_1 ((uint32_t)0x00000002) |
| #define LL_PWR_GPIO_BIT_2 ((uint32_t)0x00000004) |
| #define LL_PWR_GPIO_BIT_3 ((uint32_t)0x00000008) |
| #define LL_PWR_GPIO_BIT_4 ((uint32_t)0x00000010) |
| #define LL_PWR_GPIO_BIT_5 ((uint32_t)0x00000020) |
| #define LL_PWR_GPIO_BIT_6 ((uint32_t)0x00000040) |
| #define LL_PWR_GPIO_BIT_7 ((uint32_t)0x00000080) |
| #define LL_PWR_GPIO_BIT_8 ((uint32_t)0x00000100) |
| #define LL_PWR_GPIO_BIT_9 ((uint32_t)0x00000200) |
| #define LL_PWR_GPIO_BIT_10 ((uint32_t)0x00000400) |
| #define LL_PWR_GPIO_BIT_11 ((uint32_t)0x00000800) |
| #define LL_PWR_GPIO_BIT_12 ((uint32_t)0x00001000) |
| #define LL_PWR_GPIO_BIT_13 ((uint32_t)0x00002000) |
| #define LL_PWR_GPIO_BIT_14 ((uint32_t)0x00004000) |
| #define LL_PWR_GPIO_BIT_15 ((uint32_t)0x00008000) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| /** @defgroup PWR_LL_Exported_Macros PWR Exported Macros |
| * @{ |
| */ |
| |
| /** @defgroup PWR_LL_EM_WRITE_READ Common Write and read registers Macros |
| * @{ |
| */ |
| |
| /** |
| * @brief Write a value in PWR register |
| * @param __REG__ Register to be written |
| * @param __VALUE__ Value to be written in the register |
| * @retval None |
| */ |
| #define LL_PWR_WriteReg(__REG__, __VALUE__) WRITE_REG(PWR->__REG__, (__VALUE__)) |
| |
| /** |
| * @brief Read a value in PWR register |
| * @param __REG__ Register to be read |
| * @retval Register value |
| */ |
| #define LL_PWR_ReadReg(__REG__) READ_REG(PWR->__REG__) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @defgroup PWR_LL_Exported_Functions PWR Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup PWR_LL_EF_Configuration Configuration |
| * @{ |
| */ |
| |
| /** |
| * @brief Switch the regulator from main mode to low-power mode |
| * @rmtoll CR1 LPR LL_PWR_EnableLowPowerRunMode |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableLowPowerRunMode(void) |
| { |
| SET_BIT(PWR->CR1, PWR_CR1_LPR); |
| } |
| |
| /** |
| * @brief Switch the regulator from low-power mode to main mode |
| * @rmtoll CR1 LPR LL_PWR_DisableLowPowerRunMode |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableLowPowerRunMode(void) |
| { |
| CLEAR_BIT(PWR->CR1, PWR_CR1_LPR); |
| } |
| |
| /** |
| * @brief Check if the regulator is in low-power mode |
| * @rmtoll CR1 LPR LL_PWR_IsEnabledLowPowerRunMode |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledLowPowerRunMode(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR1, PWR_CR1_LPR); |
| |
| return ((temp == (PWR_CR1_LPR))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Switch from run main mode to run low-power mode. |
| * @rmtoll CR1 LPR LL_PWR_EnterLowPowerRunMode |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnterLowPowerRunMode(void) |
| { |
| LL_PWR_EnableLowPowerRunMode(); |
| } |
| |
| /** |
| * @brief Switch from run main mode to low-power mode. |
| * @rmtoll CR1 LPR LL_PWR_ExitLowPowerRunMode |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ExitLowPowerRunMode(void) |
| { |
| LL_PWR_DisableLowPowerRunMode(); |
| } |
| |
| /** |
| * @brief Set the main internal regulator output voltage |
| * @rmtoll CR1 VOS LL_PWR_SetRegulVoltageScaling |
| * @param VoltageScaling This parameter can be one of the following values: |
| * @arg @ref LL_PWR_REGU_VOLTAGE_SCALE1 |
| * @arg @ref LL_PWR_REGU_VOLTAGE_SCALE2 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_SetRegulVoltageScaling(uint32_t VoltageScaling) |
| { |
| MODIFY_REG(PWR->CR1, PWR_CR1_VOS, VoltageScaling); |
| } |
| |
| /** |
| * @brief Get the main internal regulator output voltage |
| * @rmtoll CR1 VOS LL_PWR_GetRegulVoltageScaling |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_PWR_REGU_VOLTAGE_SCALE1 |
| * @arg @ref LL_PWR_REGU_VOLTAGE_SCALE2 |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_GetRegulVoltageScaling(void) |
| { |
| return (uint32_t)(READ_BIT(PWR->CR1, PWR_CR1_VOS)); |
| } |
| |
| #if defined(PWR_CR5_R1MODE) |
| /** |
| * @brief Enable main regulator voltage range 1 boost mode |
| * @rmtoll CR5 R1MODE LL_PWR_EnableRange1BoostMode |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableRange1BoostMode(void) |
| { |
| CLEAR_BIT(PWR->CR5, PWR_CR5_R1MODE); |
| } |
| |
| /** |
| * @brief Disable main regulator voltage range 1 boost mode |
| * @rmtoll CR5 R1MODE LL_PWR_DisableRange1BoostMode |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableRange1BoostMode(void) |
| { |
| SET_BIT(PWR->CR5, PWR_CR5_R1MODE); |
| } |
| |
| /** |
| * @brief Check if the main regulator voltage range 1 boost mode is enabled |
| * @rmtoll CR5 R1MODE LL_PWR_IsEnabledRange1BoostMode |
| * @retval Inverted state of bit (0 or 1). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledRange1BoostMode(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR5, PWR_CR5_R1MODE); |
| |
| return ((temp == (0U))?1U:0U); |
| } |
| #endif /* PWR_CR5_R1MODE */ |
| |
| /** |
| * @brief Enable access to the backup domain |
| * @rmtoll CR1 DBP LL_PWR_EnableBkUpAccess |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableBkUpAccess(void) |
| { |
| SET_BIT(PWR->CR1, PWR_CR1_DBP); |
| } |
| |
| /** |
| * @brief Disable access to the backup domain |
| * @rmtoll CR1 DBP LL_PWR_DisableBkUpAccess |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableBkUpAccess(void) |
| { |
| CLEAR_BIT(PWR->CR1, PWR_CR1_DBP); |
| } |
| |
| /** |
| * @brief Check if the backup domain is enabled |
| * @rmtoll CR1 DBP LL_PWR_IsEnabledBkUpAccess |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledBkUpAccess(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR1, PWR_CR1_DBP); |
| |
| return ((temp == (PWR_CR1_DBP))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Set Low-Power mode |
| * @rmtoll CR1 LPMS LL_PWR_SetPowerMode |
| * @param LowPowerMode This parameter can be one of the following values: |
| * @arg @ref LL_PWR_MODE_STOP0 |
| * @arg @ref LL_PWR_MODE_STOP1 |
| * @arg @ref LL_PWR_MODE_STANDBY |
| * @arg @ref LL_PWR_MODE_SHUTDOWN |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_SetPowerMode(uint32_t LowPowerMode) |
| { |
| MODIFY_REG(PWR->CR1, PWR_CR1_LPMS, LowPowerMode); |
| } |
| |
| /** |
| * @brief Get Low-Power mode |
| * @rmtoll CR1 LPMS LL_PWR_GetPowerMode |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_PWR_MODE_STOP0 |
| * @arg @ref LL_PWR_MODE_STOP1 |
| * @arg @ref LL_PWR_MODE_STANDBY |
| * @arg @ref LL_PWR_MODE_SHUTDOWN |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_GetPowerMode(void) |
| { |
| return (uint32_t)(READ_BIT(PWR->CR1, PWR_CR1_LPMS)); |
| } |
| |
| #if defined(PWR_CR3_UCPD_STDBY) |
| /** |
| * @brief Enable (write 1) the USB Type-C and Power Delivery standby mode. |
| * @note Enable just before entering standby when using UCPD1. |
| * @rmtoll CR3 UCPD1_STDBY LL_PWR_EnableUSBStandByModePD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableUSBStandByModePD(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_UCPD_STDBY); |
| } |
| |
| /** |
| * @brief Disable (write 0) USB Type-C and Power Delivery standby mode. |
| * @note Disable immediately after standby exit when using UCPD1, |
| * (and before writing any UCPD1 registers). |
| * @rmtoll CR3 UCPD1_STDBY LL_PWR_DisableUSBStandByModePD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableUSBStandByModePD(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_UCPD_STDBY); |
| } |
| |
| /** |
| * @brief Check the USB Type-C and Power Delivery standby mode. |
| * @rmtoll CR3 UCPD1_STDBY LL_PWR_IsEnabledUSBStandByModePD |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledUSBStandByModePD(void) |
| { |
| |
| return ((READ_BIT(PWR->CR3, PWR_CR3_UCPD_STDBY) == (PWR_CR3_UCPD_STDBY))?1UL:0UL); |
| |
| } |
| #endif /* PWR_CR3_UCPD_STDBY */ |
| |
| #if defined(PWR_CR3_UCPD_DBDIS) |
| /** |
| * @brief Enable (write 0) USB Type-C dead battery pull-down behavior |
| * on UCPD1_CC1 and UCPD1_CC2 pins. |
| * @note After exiting reset, the USB Type-C “dead battery” behavior will be enabled, |
| * which may have a pull-down effect on CC1 and CC2 pins. It is recommended to disable it |
| * in all cases, either to stop this pull-down or to hand over control to the UCPD1 |
| * (which should therefore be initialized before doing the disable). |
| * @rmtoll CR3 PWR_CR3_UCPD_DBDIS LL_PWR_EnableUSBDeadBattery |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableUSBDeadBattery(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_UCPD_DBDIS); |
| } |
| |
| /** |
| * @brief Disable (write 1) USB Type-C dead battery pull-down behavior |
| * on UCPD1_CC1 and UCPD1_CC2 pins. |
| * @note After exiting reset, the USB Type-C “dead battery” behavior will be enabled, |
| * which may have a pull-down effect on CC1 and CC2 pins. It is recommended to disable it |
| * in all cases, either to stop this pull-down or to hand over control to the UCPD1 |
| * (which should therefore be initialized before doing the disable). |
| * @rmtoll CR3 PWR_CR3_UCPD_DBDIS LL_PWR_DisableUSBDeadBattery |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableUSBDeadBattery(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_UCPD_DBDIS); |
| } |
| |
| /** |
| * @brief Check USB Type-C dead battery pull-down behavior |
| * on UCPD1_CC1 and UCPD1_CC2 pins. |
| * @note After exiting reset, the USB Type-C “dead battery” behavior will be enabled, |
| * which may have a pull-down effect on CC1 and CC2 pins. It is recommended to disable it |
| * in all cases, either to stop this pull-down or to hand over control to the UCPD1 |
| * (which should therefore be initialized before doing the disable). |
| * @rmtoll CR3 PWR_CR3_UCPD_DBDIS LL_PWR_IsEnabledUSBDeadBattery |
| * @retval State of bit. |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledUSBDeadBattery(void) |
| { |
| |
| return ((READ_BIT(PWR->CR3, PWR_CR3_UCPD_DBDIS) == (PWR_CR3_UCPD_DBDIS))?1UL:0UL); |
| |
| } |
| #endif /* PWR_CR3_UCPD_DBDIS */ |
| |
| #if defined(PWR_CR2_USV) |
| /** |
| * @brief Enable VDDUSB supply |
| * @rmtoll CR2 USV LL_PWR_EnableVddUSB |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableVddUSB(void) |
| { |
| SET_BIT(PWR->CR2, PWR_CR2_USV); |
| } |
| |
| /** |
| * @brief Disable VDDUSB supply |
| * @rmtoll CR2 USV LL_PWR_DisableVddUSB |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableVddUSB(void) |
| { |
| CLEAR_BIT(PWR->CR2, PWR_CR2_USV); |
| } |
| |
| /** |
| * @brief Check if VDDUSB supply is enabled |
| * @rmtoll CR2 USV LL_PWR_IsEnabledVddUSB |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledVddUSB(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR2, PWR_CR2_USV); |
| |
| return ((temp == (PWR_CR2_USV))?1U:0U); |
| |
| } |
| #endif |
| |
| #if defined(PWR_CR2_IOSV) |
| /** |
| * @brief Enable VDDIO2 supply |
| * @rmtoll CR2 IOSV LL_PWR_EnableVddIO2 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableVddIO2(void) |
| { |
| SET_BIT(PWR->CR2, PWR_CR2_IOSV); |
| } |
| |
| /** |
| * @brief Disable VDDIO2 supply |
| * @rmtoll CR2 IOSV LL_PWR_DisableVddIO2 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableVddIO2(void) |
| { |
| CLEAR_BIT(PWR->CR2, PWR_CR2_IOSV); |
| } |
| |
| /** |
| * @brief Check if VDDIO2 supply is enabled |
| * @rmtoll CR2 IOSV LL_PWR_IsEnabledVddIO2 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledVddIO2(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR2, PWR_CR2_IOSV); |
| |
| return ((temp == (PWR_CR2_IOSV))?1U:0U); |
| |
| } |
| #endif |
| |
| /** |
| * @brief Enable the Power Voltage Monitoring on a peripheral |
| * @rmtoll CR2 PVME1 LL_PWR_EnablePVM\n |
| * CR2 PVME2 LL_PWR_EnablePVM\n |
| * CR2 PVME3 LL_PWR_EnablePVM\n |
| * CR2 PVME4 LL_PWR_EnablePVM |
| * @param PeriphVoltage This parameter can be one of the following values: |
| * @arg @ref LL_PWR_PVM_VDDA_COMP (*) |
| * @arg @ref LL_PWR_PVM_VDDA_FASTDAC (*) |
| * @arg @ref LL_PWR_PVM_VDDA_ADC |
| * @arg @ref LL_PWR_PVM_VDDA_OPAMP_DAC |
| * |
| * (*) value not defined in all devices |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnablePVM(uint32_t PeriphVoltage) |
| { |
| SET_BIT(PWR->CR2, PeriphVoltage); |
| } |
| |
| /** |
| * @brief Disable the Power Voltage Monitoring on a peripheral |
| * @rmtoll CR2 PVME1 LL_PWR_DisablePVM\n |
| * CR2 PVME2 LL_PWR_DisablePVM\n |
| * CR2 PVME3 LL_PWR_DisablePVM\n |
| * CR2 PVME4 LL_PWR_DisablePVM |
| * @param PeriphVoltage This parameter can be one of the following values: |
| * @arg @ref LL_PWR_PVM_VDDA_COMP (*) |
| * @arg @ref LL_PWR_PVM_VDDA_FASTDAC (*) |
| * @arg @ref LL_PWR_PVM_VDDA_ADC |
| * @arg @ref LL_PWR_PVM_VDDA_OPAMP_DAC |
| * |
| * (*) value not defined in all devices |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisablePVM(uint32_t PeriphVoltage) |
| { |
| CLEAR_BIT(PWR->CR2, PeriphVoltage); |
| } |
| |
| /** |
| * @brief Check if Power Voltage Monitoring is enabled on a peripheral |
| * @rmtoll CR2 PVME1 LL_PWR_IsEnabledPVM\n |
| * CR2 PVME2 LL_PWR_IsEnabledPVM\n |
| * CR2 PVME3 LL_PWR_IsEnabledPVM\n |
| * CR2 PVME4 LL_PWR_IsEnabledPVM |
| * @param PeriphVoltage This parameter can be one of the following values: |
| * @arg @ref LL_PWR_PVM_VDDA_COMP (*) |
| * @arg @ref LL_PWR_PVM_VDDA_FASTDAC (*) |
| * @arg @ref LL_PWR_PVM_VDDA_ADC |
| * @arg @ref LL_PWR_PVM_VDDA_OPAMP_DAC |
| * |
| * (*) value not defined in all devices |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledPVM(uint32_t PeriphVoltage) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR2, PeriphVoltage); |
| |
| return ((temp == (PeriphVoltage))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Configure the voltage threshold detected by the Power Voltage Detector |
| * @rmtoll CR2 PLS LL_PWR_SetPVDLevel |
| * @param PVDLevel This parameter can be one of the following values: |
| * @arg @ref LL_PWR_PVDLEVEL_0 |
| * @arg @ref LL_PWR_PVDLEVEL_1 |
| * @arg @ref LL_PWR_PVDLEVEL_2 |
| * @arg @ref LL_PWR_PVDLEVEL_3 |
| * @arg @ref LL_PWR_PVDLEVEL_4 |
| * @arg @ref LL_PWR_PVDLEVEL_5 |
| * @arg @ref LL_PWR_PVDLEVEL_6 |
| * @arg @ref LL_PWR_PVDLEVEL_7 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_SetPVDLevel(uint32_t PVDLevel) |
| { |
| MODIFY_REG(PWR->CR2, PWR_CR2_PLS, PVDLevel); |
| } |
| |
| /** |
| * @brief Get the voltage threshold detection |
| * @rmtoll CR2 PLS LL_PWR_GetPVDLevel |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_PWR_PVDLEVEL_0 |
| * @arg @ref LL_PWR_PVDLEVEL_1 |
| * @arg @ref LL_PWR_PVDLEVEL_2 |
| * @arg @ref LL_PWR_PVDLEVEL_3 |
| * @arg @ref LL_PWR_PVDLEVEL_4 |
| * @arg @ref LL_PWR_PVDLEVEL_5 |
| * @arg @ref LL_PWR_PVDLEVEL_6 |
| * @arg @ref LL_PWR_PVDLEVEL_7 |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_GetPVDLevel(void) |
| { |
| return (uint32_t)(READ_BIT(PWR->CR2, PWR_CR2_PLS)); |
| } |
| |
| /** |
| * @brief Enable Power Voltage Detector |
| * @rmtoll CR2 PVDE LL_PWR_EnablePVD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnablePVD(void) |
| { |
| SET_BIT(PWR->CR2, PWR_CR2_PVDE); |
| } |
| |
| /** |
| * @brief Disable Power Voltage Detector |
| * @rmtoll CR2 PVDE LL_PWR_DisablePVD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisablePVD(void) |
| { |
| CLEAR_BIT(PWR->CR2, PWR_CR2_PVDE); |
| } |
| |
| /** |
| * @brief Check if Power Voltage Detector is enabled |
| * @rmtoll CR2 PVDE LL_PWR_IsEnabledPVD |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledPVD(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR2, PWR_CR2_PVDE); |
| |
| return ((temp == (PWR_CR2_PVDE))?1U:0U); |
| } |
| |
| /** |
| * @brief Enable Internal Wake-up line |
| * @rmtoll CR3 EIWF LL_PWR_EnableInternWU |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableInternWU(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_EIWF); |
| } |
| |
| /** |
| * @brief Disable Internal Wake-up line |
| * @rmtoll CR3 EIWF LL_PWR_DisableInternWU |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableInternWU(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_EIWF); |
| } |
| |
| /** |
| * @brief Check if Internal Wake-up line is enabled |
| * @rmtoll CR3 EIWF LL_PWR_IsEnabledInternWU |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledInternWU(void) |
| { |
| return ((READ_BIT(PWR->CR3, PWR_CR3_EIWF) == (PWR_CR3_EIWF))?1UL:0UL); |
| } |
| |
| #if defined (PWR_CR3_UCPD_DBDIS) |
| /** |
| * @brief Enable USB Type-C and Power Delivery Dead Battery disable |
| * @rmtoll CR3 UCPD_DBDIS LL_PWR_EnableDeadBatteryPD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableDeadBatteryPD(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_UCPD_DBDIS); |
| } |
| |
| /** |
| * @brief Disable USB Type-C and Power Delivery Dead Battery disable |
| * @rmtoll CR3 UCPD_DBDIS LL_PWR_DisableDeadBatteryPD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableDeadBatteryPD(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_UCPD_DBDIS); |
| } |
| #endif /* PWR_CR3_UCPD_DBDIS */ |
| |
| #if defined(PWR_CR3_UCPD_STDBY) |
| /** |
| * @brief Enable USB Type-C and Power Delivery standby mode. |
| * @rmtoll CR3 UCPD_STDBY LL_PWR_EnableStandByModePD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableStandByModePD(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_UCPD_STDBY); |
| } |
| |
| /** |
| * @brief Disable USB Type-C and Power Delivery standby mode. |
| * @rmtoll CR3 UCPD_STDBY LL_PWR_DisableStandByModePD |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableStandByModePD(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_UCPD_STDBY); |
| } |
| #endif /* PWR_CR3_UCPD_STDBY */ |
| |
| /** |
| * @brief Enable pull-up and pull-down configuration |
| * @rmtoll CR3 APC LL_PWR_EnablePUPDCfg |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnablePUPDCfg(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_APC); |
| } |
| |
| /** |
| * @brief Disable pull-up and pull-down configuration |
| * @rmtoll CR3 APC LL_PWR_DisablePUPDCfg |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisablePUPDCfg(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_APC); |
| } |
| |
| /** |
| * @brief Check if pull-up and pull-down configuration is enabled |
| * @rmtoll CR3 APC LL_PWR_IsEnabledPUPDCfg |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledPUPDCfg(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR3, PWR_CR3_APC); |
| |
| return ((temp == (PWR_CR3_APC))?1U:0U); |
| } |
| |
| /** |
| * @brief Enable SRAM2 content retention in Standby mode |
| * @rmtoll CR3 RRS LL_PWR_EnableSRAM2Retention |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableSRAM2Retention(void) |
| { |
| SET_BIT(PWR->CR3, PWR_CR3_RRS); |
| } |
| |
| /** |
| * @brief Disable SRAM2 content retention in Standby mode |
| * @rmtoll CR3 RRS LL_PWR_DisableSRAM2Retention |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableSRAM2Retention(void) |
| { |
| CLEAR_BIT(PWR->CR3, PWR_CR3_RRS); |
| } |
| |
| /** |
| * @brief Check if SRAM2 content retention in Standby mode is enabled |
| * @rmtoll CR3 RRS LL_PWR_IsEnabledSRAM2Retention |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledSRAM2Retention(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR3, PWR_CR3_RRS); |
| |
| return ((temp == (PWR_CR3_RRS))?1U:0U); |
| } |
| |
| /** |
| * @brief Enable the WakeUp PINx functionality |
| * @rmtoll CR3 EWUP1 LL_PWR_EnableWakeUpPin\n |
| * CR3 EWUP2 LL_PWR_EnableWakeUpPin\n |
| * CR3 EWUP3 LL_PWR_EnableWakeUpPin\n |
| * CR3 EWUP4 LL_PWR_EnableWakeUpPin\n |
| * CR3 EWUP5 LL_PWR_EnableWakeUpPin\n |
| * @param WakeUpPin This parameter can be one of the following values: |
| * @arg @ref LL_PWR_WAKEUP_PIN1 |
| * @arg @ref LL_PWR_WAKEUP_PIN2 |
| * @arg @ref LL_PWR_WAKEUP_PIN3 |
| * @arg @ref LL_PWR_WAKEUP_PIN4 |
| * @arg @ref LL_PWR_WAKEUP_PIN5 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableWakeUpPin(uint32_t WakeUpPin) |
| { |
| SET_BIT(PWR->CR3, WakeUpPin); |
| } |
| |
| /** |
| * @brief Disable the WakeUp PINx functionality |
| * @rmtoll CR3 EWUP1 LL_PWR_DisableWakeUpPin\n |
| * CR3 EWUP2 LL_PWR_DisableWakeUpPin\n |
| * CR3 EWUP3 LL_PWR_DisableWakeUpPin\n |
| * CR3 EWUP4 LL_PWR_DisableWakeUpPin\n |
| * CR3 EWUP5 LL_PWR_DisableWakeUpPin\n |
| * @param WakeUpPin This parameter can be one of the following values: |
| * @arg @ref LL_PWR_WAKEUP_PIN1 |
| * @arg @ref LL_PWR_WAKEUP_PIN2 |
| * @arg @ref LL_PWR_WAKEUP_PIN3 |
| * @arg @ref LL_PWR_WAKEUP_PIN4 |
| * @arg @ref LL_PWR_WAKEUP_PIN5 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableWakeUpPin(uint32_t WakeUpPin) |
| { |
| CLEAR_BIT(PWR->CR3, WakeUpPin); |
| } |
| |
| /** |
| * @brief Check if the WakeUp PINx functionality is enabled |
| * @rmtoll CR3 EWUP1 LL_PWR_IsEnabledWakeUpPin\n |
| * CR3 EWUP2 LL_PWR_IsEnabledWakeUpPin\n |
| * CR3 EWUP3 LL_PWR_IsEnabledWakeUpPin\n |
| * CR3 EWUP4 LL_PWR_IsEnabledWakeUpPin\n |
| * CR3 EWUP5 LL_PWR_IsEnabledWakeUpPin\n |
| * @param WakeUpPin This parameter can be one of the following values: |
| * @arg @ref LL_PWR_WAKEUP_PIN1 |
| * @arg @ref LL_PWR_WAKEUP_PIN2 |
| * @arg @ref LL_PWR_WAKEUP_PIN3 |
| * @arg @ref LL_PWR_WAKEUP_PIN4 |
| * @arg @ref LL_PWR_WAKEUP_PIN5 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledWakeUpPin(uint32_t WakeUpPin) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR3, WakeUpPin); |
| |
| return ((temp == (WakeUpPin))?1U:0U); |
| } |
| |
| /** |
| * @brief Set the resistor impedance |
| * @rmtoll CR4 VBRS LL_PWR_SetBattChargResistor |
| * @param Resistor This parameter can be one of the following values: |
| * @arg @ref LL_PWR_BATT_CHARG_RESISTOR_5K |
| * @arg @ref LL_PWR_BATT_CHARGRESISTOR_1_5K |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_SetBattChargResistor(uint32_t Resistor) |
| { |
| MODIFY_REG(PWR->CR4, PWR_CR4_VBRS, Resistor); |
| } |
| |
| /** |
| * @brief Get the resistor impedance |
| * @rmtoll CR4 VBRS LL_PWR_GetBattChargResistor |
| * @retval Returned value can be one of the following values: |
| * @arg @ref LL_PWR_BATT_CHARG_RESISTOR_5K |
| * @arg @ref LL_PWR_BATT_CHARGRESISTOR_1_5K |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_GetBattChargResistor(void) |
| { |
| return (uint32_t)(READ_BIT(PWR->CR4, PWR_CR4_VBRS)); |
| } |
| |
| /** |
| * @brief Enable battery charging |
| * @rmtoll CR4 VBE LL_PWR_EnableBatteryCharging |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableBatteryCharging(void) |
| { |
| SET_BIT(PWR->CR4, PWR_CR4_VBE); |
| } |
| |
| /** |
| * @brief Disable battery charging |
| * @rmtoll CR4 VBE LL_PWR_DisableBatteryCharging |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableBatteryCharging(void) |
| { |
| CLEAR_BIT(PWR->CR4, PWR_CR4_VBE); |
| } |
| |
| /** |
| * @brief Check if battery charging is enabled |
| * @rmtoll CR4 VBE LL_PWR_IsEnabledBatteryCharging |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledBatteryCharging(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR4, PWR_CR4_VBE); |
| |
| return ((temp == (PWR_CR4_VBE))?1U:0U); |
| } |
| |
| /** |
| * @brief Set the Wake-Up pin polarity low for the event detection |
| * @rmtoll CR4 WP1 LL_PWR_SetWakeUpPinPolarityLow\n |
| * CR4 WP2 LL_PWR_SetWakeUpPinPolarityLow\n |
| * CR4 WP3 LL_PWR_SetWakeUpPinPolarityLow\n |
| * CR4 WP4 LL_PWR_SetWakeUpPinPolarityLow\n |
| * CR4 WP5 LL_PWR_SetWakeUpPinPolarityLow |
| * @param WakeUpPin This parameter can be one of the following values: |
| * @arg @ref LL_PWR_WAKEUP_PIN1 |
| * @arg @ref LL_PWR_WAKEUP_PIN2 |
| * @arg @ref LL_PWR_WAKEUP_PIN3 |
| * @arg @ref LL_PWR_WAKEUP_PIN4 |
| * @arg @ref LL_PWR_WAKEUP_PIN5 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_SetWakeUpPinPolarityLow(uint32_t WakeUpPin) |
| { |
| SET_BIT(PWR->CR4, WakeUpPin); |
| } |
| |
| /** |
| * @brief Set the Wake-Up pin polarity high for the event detection |
| * @rmtoll CR4 WP1 LL_PWR_SetWakeUpPinPolarityHigh\n |
| * CR4 WP2 LL_PWR_SetWakeUpPinPolarityHigh\n |
| * CR4 WP3 LL_PWR_SetWakeUpPinPolarityHigh\n |
| * CR4 WP4 LL_PWR_SetWakeUpPinPolarityHigh\n |
| * CR4 WP5 LL_PWR_SetWakeUpPinPolarityHigh |
| * @param WakeUpPin This parameter can be one of the following values: |
| * @arg @ref LL_PWR_WAKEUP_PIN1 |
| * @arg @ref LL_PWR_WAKEUP_PIN2 |
| * @arg @ref LL_PWR_WAKEUP_PIN3 |
| * @arg @ref LL_PWR_WAKEUP_PIN4 |
| * @arg @ref LL_PWR_WAKEUP_PIN5 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_SetWakeUpPinPolarityHigh(uint32_t WakeUpPin) |
| { |
| CLEAR_BIT(PWR->CR4, WakeUpPin); |
| } |
| |
| /** |
| * @brief Get the Wake-Up pin polarity for the event detection |
| * @rmtoll CR4 WP1 LL_PWR_IsWakeUpPinPolarityLow\n |
| * CR4 WP2 LL_PWR_IsWakeUpPinPolarityLow\n |
| * CR4 WP3 LL_PWR_IsWakeUpPinPolarityLow\n |
| * CR4 WP4 LL_PWR_IsWakeUpPinPolarityLow\n |
| * CR4 WP5 LL_PWR_IsWakeUpPinPolarityLow |
| * @param WakeUpPin This parameter can be one of the following values: |
| * @arg @ref LL_PWR_WAKEUP_PIN1 |
| * @arg @ref LL_PWR_WAKEUP_PIN2 |
| * @arg @ref LL_PWR_WAKEUP_PIN3 |
| * @arg @ref LL_PWR_WAKEUP_PIN4 |
| * @arg @ref LL_PWR_WAKEUP_PIN5 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsWakeUpPinPolarityLow(uint32_t WakeUpPin) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->CR4, WakeUpPin); |
| |
| return ((temp == (WakeUpPin))?1U:0U); |
| } |
| |
| /** |
| * @brief Enable GPIO pull-up state in Standby and Shutdown modes |
| * @rmtoll PUCRA PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * PUCRB PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * PUCRC PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * PUCRD PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * PUCRE PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * PUCRF PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * PUCRG PU0-15 LL_PWR_EnableGPIOPullUp\n |
| * @param GPIO This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_A |
| * @arg @ref LL_PWR_GPIO_B |
| * @arg @ref LL_PWR_GPIO_C |
| * @arg @ref LL_PWR_GPIO_D |
| * @arg @ref LL_PWR_GPIO_E |
| * @arg @ref LL_PWR_GPIO_F |
| * @arg @ref LL_PWR_GPIO_G |
| * |
| * (*) value not defined in all devices |
| * @param GPIONumber This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_BIT_0 |
| * @arg @ref LL_PWR_GPIO_BIT_1 |
| * @arg @ref LL_PWR_GPIO_BIT_2 |
| * @arg @ref LL_PWR_GPIO_BIT_3 |
| * @arg @ref LL_PWR_GPIO_BIT_4 |
| * @arg @ref LL_PWR_GPIO_BIT_5 |
| * @arg @ref LL_PWR_GPIO_BIT_6 |
| * @arg @ref LL_PWR_GPIO_BIT_7 |
| * @arg @ref LL_PWR_GPIO_BIT_8 |
| * @arg @ref LL_PWR_GPIO_BIT_9 |
| * @arg @ref LL_PWR_GPIO_BIT_10 |
| * @arg @ref LL_PWR_GPIO_BIT_11 |
| * @arg @ref LL_PWR_GPIO_BIT_12 |
| * @arg @ref LL_PWR_GPIO_BIT_13 |
| * @arg @ref LL_PWR_GPIO_BIT_14 |
| * @arg @ref LL_PWR_GPIO_BIT_15 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber) |
| { |
| SET_BIT(*((uint32_t *)GPIO), GPIONumber); |
| } |
| |
| /** |
| * @brief Disable GPIO pull-up state in Standby and Shutdown modes |
| * @rmtoll PUCRA PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * PUCRB PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * PUCRC PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * PUCRD PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * PUCRE PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * PUCRF PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * PUCRG PU0-15 LL_PWR_DisableGPIOPullUp\n |
| * @param GPIO This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_A |
| * @arg @ref LL_PWR_GPIO_B |
| * @arg @ref LL_PWR_GPIO_C |
| * @arg @ref LL_PWR_GPIO_D |
| * @arg @ref LL_PWR_GPIO_E |
| * @arg @ref LL_PWR_GPIO_F |
| * @arg @ref LL_PWR_GPIO_G |
| * |
| * (*) value not defined in all devices |
| * @param GPIONumber This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_BIT_0 |
| * @arg @ref LL_PWR_GPIO_BIT_1 |
| * @arg @ref LL_PWR_GPIO_BIT_2 |
| * @arg @ref LL_PWR_GPIO_BIT_3 |
| * @arg @ref LL_PWR_GPIO_BIT_4 |
| * @arg @ref LL_PWR_GPIO_BIT_5 |
| * @arg @ref LL_PWR_GPIO_BIT_6 |
| * @arg @ref LL_PWR_GPIO_BIT_7 |
| * @arg @ref LL_PWR_GPIO_BIT_8 |
| * @arg @ref LL_PWR_GPIO_BIT_9 |
| * @arg @ref LL_PWR_GPIO_BIT_10 |
| * @arg @ref LL_PWR_GPIO_BIT_11 |
| * @arg @ref LL_PWR_GPIO_BIT_12 |
| * @arg @ref LL_PWR_GPIO_BIT_13 |
| * @arg @ref LL_PWR_GPIO_BIT_14 |
| * @arg @ref LL_PWR_GPIO_BIT_15 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber) |
| { |
| CLEAR_BIT(*((uint32_t *)GPIO), GPIONumber); |
| } |
| |
| /** |
| * @brief Check if GPIO pull-up state is enabled |
| * @rmtoll PUCRA PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * PUCRB PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * PUCRC PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * PUCRD PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * PUCRE PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * PUCRF PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * PUCRG PU0-15 LL_PWR_IsEnabledGPIOPullUp\n |
| * @param GPIO This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_A |
| * @arg @ref LL_PWR_GPIO_B |
| * @arg @ref LL_PWR_GPIO_C |
| * @arg @ref LL_PWR_GPIO_D |
| * @arg @ref LL_PWR_GPIO_E |
| * @arg @ref LL_PWR_GPIO_F |
| * @arg @ref LL_PWR_GPIO_G |
| * |
| * (*) value not defined in all devices |
| * @param GPIONumber This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_BIT_0 |
| * @arg @ref LL_PWR_GPIO_BIT_1 |
| * @arg @ref LL_PWR_GPIO_BIT_2 |
| * @arg @ref LL_PWR_GPIO_BIT_3 |
| * @arg @ref LL_PWR_GPIO_BIT_4 |
| * @arg @ref LL_PWR_GPIO_BIT_5 |
| * @arg @ref LL_PWR_GPIO_BIT_6 |
| * @arg @ref LL_PWR_GPIO_BIT_7 |
| * @arg @ref LL_PWR_GPIO_BIT_8 |
| * @arg @ref LL_PWR_GPIO_BIT_9 |
| * @arg @ref LL_PWR_GPIO_BIT_10 |
| * @arg @ref LL_PWR_GPIO_BIT_11 |
| * @arg @ref LL_PWR_GPIO_BIT_12 |
| * @arg @ref LL_PWR_GPIO_BIT_13 |
| * @arg @ref LL_PWR_GPIO_BIT_14 |
| * @arg @ref LL_PWR_GPIO_BIT_15 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber) |
| { |
| uint32_t temp; |
| temp = READ_BIT(*((uint32_t *)(GPIO)), GPIONumber); |
| |
| return ((temp == (GPIONumber))?1U:0U); |
| } |
| |
| /** |
| * @brief Enable GPIO pull-down state in Standby and Shutdown modes |
| * @rmtoll PDCRA PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * PDCRB PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * PDCRC PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * PDCRD PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * PDCRE PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * PDCRF PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * PDCRG PD0-15 LL_PWR_EnableGPIOPullDown\n |
| * @param GPIO This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_A |
| * @arg @ref LL_PWR_GPIO_B |
| * @arg @ref LL_PWR_GPIO_C |
| * @arg @ref LL_PWR_GPIO_D |
| * @arg @ref LL_PWR_GPIO_E |
| * @arg @ref LL_PWR_GPIO_F |
| * @arg @ref LL_PWR_GPIO_G |
| * |
| * (*) value not defined in all devices |
| * @param GPIONumber This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_BIT_0 |
| * @arg @ref LL_PWR_GPIO_BIT_1 |
| * @arg @ref LL_PWR_GPIO_BIT_2 |
| * @arg @ref LL_PWR_GPIO_BIT_3 |
| * @arg @ref LL_PWR_GPIO_BIT_4 |
| * @arg @ref LL_PWR_GPIO_BIT_5 |
| * @arg @ref LL_PWR_GPIO_BIT_6 |
| * @arg @ref LL_PWR_GPIO_BIT_7 |
| * @arg @ref LL_PWR_GPIO_BIT_8 |
| * @arg @ref LL_PWR_GPIO_BIT_9 |
| * @arg @ref LL_PWR_GPIO_BIT_10 |
| * @arg @ref LL_PWR_GPIO_BIT_11 |
| * @arg @ref LL_PWR_GPIO_BIT_12 |
| * @arg @ref LL_PWR_GPIO_BIT_13 |
| * @arg @ref LL_PWR_GPIO_BIT_14 |
| * @arg @ref LL_PWR_GPIO_BIT_15 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_EnableGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber) |
| { |
| register uint32_t temp = (uint32_t)(GPIO) + 4U; |
| SET_BIT(*((uint32_t *)(temp)), GPIONumber); |
| } |
| |
| /** |
| * @brief Disable GPIO pull-down state in Standby and Shutdown modes |
| * @rmtoll PDCRA PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * PDCRB PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * PDCRC PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * PDCRD PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * PDCRE PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * PDCRF PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * PDCRG PD0-15 LL_PWR_DisableGPIOPullDown\n |
| * @param GPIO This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_A |
| * @arg @ref LL_PWR_GPIO_B |
| * @arg @ref LL_PWR_GPIO_C |
| * @arg @ref LL_PWR_GPIO_D |
| * @arg @ref LL_PWR_GPIO_E |
| * @arg @ref LL_PWR_GPIO_F |
| * @arg @ref LL_PWR_GPIO_G |
| * |
| * (*) value not defined in all devices |
| * @param GPIONumber This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_BIT_0 |
| * @arg @ref LL_PWR_GPIO_BIT_1 |
| * @arg @ref LL_PWR_GPIO_BIT_2 |
| * @arg @ref LL_PWR_GPIO_BIT_3 |
| * @arg @ref LL_PWR_GPIO_BIT_4 |
| * @arg @ref LL_PWR_GPIO_BIT_5 |
| * @arg @ref LL_PWR_GPIO_BIT_6 |
| * @arg @ref LL_PWR_GPIO_BIT_7 |
| * @arg @ref LL_PWR_GPIO_BIT_8 |
| * @arg @ref LL_PWR_GPIO_BIT_9 |
| * @arg @ref LL_PWR_GPIO_BIT_10 |
| * @arg @ref LL_PWR_GPIO_BIT_11 |
| * @arg @ref LL_PWR_GPIO_BIT_12 |
| * @arg @ref LL_PWR_GPIO_BIT_13 |
| * @arg @ref LL_PWR_GPIO_BIT_14 |
| * @arg @ref LL_PWR_GPIO_BIT_15 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_DisableGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber) |
| { |
| register uint32_t temp = (uint32_t)(GPIO) + 4U; |
| CLEAR_BIT(*((uint32_t *)(temp)), GPIONumber); |
| } |
| |
| /** |
| * @brief Check if GPIO pull-down state is enabled |
| * @rmtoll PDCRA PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * PDCRB PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * PDCRC PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * PDCRD PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * PDCRE PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * PDCRF PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * PDCRG PD0-15 LL_PWR_IsEnabledGPIOPullDown\n |
| * @param GPIO This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_A |
| * @arg @ref LL_PWR_GPIO_B |
| * @arg @ref LL_PWR_GPIO_C |
| * @arg @ref LL_PWR_GPIO_D |
| * @arg @ref LL_PWR_GPIO_E |
| * @arg @ref LL_PWR_GPIO_F |
| * @arg @ref LL_PWR_GPIO_G |
| * |
| * (*) value not defined in all devices |
| * @param GPIONumber This parameter can be one of the following values: |
| * @arg @ref LL_PWR_GPIO_BIT_0 |
| * @arg @ref LL_PWR_GPIO_BIT_1 |
| * @arg @ref LL_PWR_GPIO_BIT_2 |
| * @arg @ref LL_PWR_GPIO_BIT_3 |
| * @arg @ref LL_PWR_GPIO_BIT_4 |
| * @arg @ref LL_PWR_GPIO_BIT_5 |
| * @arg @ref LL_PWR_GPIO_BIT_6 |
| * @arg @ref LL_PWR_GPIO_BIT_7 |
| * @arg @ref LL_PWR_GPIO_BIT_8 |
| * @arg @ref LL_PWR_GPIO_BIT_9 |
| * @arg @ref LL_PWR_GPIO_BIT_10 |
| * @arg @ref LL_PWR_GPIO_BIT_11 |
| * @arg @ref LL_PWR_GPIO_BIT_12 |
| * @arg @ref LL_PWR_GPIO_BIT_13 |
| * @arg @ref LL_PWR_GPIO_BIT_14 |
| * @arg @ref LL_PWR_GPIO_BIT_15 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsEnabledGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber) |
| { |
| register uint32_t temp_reg = (uint32_t)(GPIO) + 4U; |
| uint32_t temp; |
| temp = READ_BIT(*((uint32_t *)(temp_reg)), GPIONumber); |
| |
| return ((temp == (GPIONumber))?1U:0U); |
| |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWR_LL_EF_FLAG_Management FLAG_Management |
| * @{ |
| */ |
| |
| /** |
| * @brief Get Internal Wake-up line Flag |
| * @rmtoll SR1 WUFI LL_PWR_IsActiveFlag_InternWU |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_InternWU(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_WUFI); |
| |
| return ((temp == (PWR_SR1_WUFI))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Get Stand-By Flag |
| * @rmtoll SR1 SBF LL_PWR_IsActiveFlag_SB |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_SB(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_SBF); |
| |
| return ((temp == (PWR_SR1_SBF))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Get Wake-up Flag 5 |
| * @rmtoll SR1 WUF5 LL_PWR_IsActiveFlag_WU5 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_WU5(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_WUF5); |
| |
| return ((temp == (PWR_SR1_WUF5))?1U:0U); |
| } |
| |
| /** |
| * @brief Get Wake-up Flag 4 |
| * @rmtoll SR1 WUF4 LL_PWR_IsActiveFlag_WU4 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_WU4(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_WUF4); |
| |
| return ((temp == (PWR_SR1_WUF4))?1U:0U); |
| } |
| |
| /** |
| * @brief Get Wake-up Flag 3 |
| * @rmtoll SR1 WUF3 LL_PWR_IsActiveFlag_WU3 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_WU3(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_WUF3); |
| |
| return ((temp == (PWR_SR1_WUF3))?1U:0U); |
| } |
| |
| /** |
| * @brief Get Wake-up Flag 2 |
| * @rmtoll SR1 WUF2 LL_PWR_IsActiveFlag_WU2 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_WU2(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_WUF2); |
| |
| return ((temp == (PWR_SR1_WUF2))?1U:0U); |
| } |
| |
| /** |
| * @brief Get Wake-up Flag 1 |
| * @rmtoll SR1 WUF1 LL_PWR_IsActiveFlag_WU1 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_WU1(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR1, PWR_SR1_WUF1); |
| |
| return ((temp == (PWR_SR1_WUF1))?1U:0U); |
| } |
| |
| /** |
| * @brief Clear Stand-By Flag |
| * @rmtoll SCR CSBF LL_PWR_ClearFlag_SB |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_SB(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CSBF); |
| } |
| |
| /** |
| * @brief Clear Wake-up Flags |
| * @rmtoll SCR CWUF LL_PWR_ClearFlag_WU |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_WU(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CWUF); |
| } |
| |
| /** |
| * @brief Clear Wake-up Flag 5 |
| * @rmtoll SCR CWUF5 LL_PWR_ClearFlag_WU5 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_WU5(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CWUF5); |
| } |
| |
| /** |
| * @brief Clear Wake-up Flag 4 |
| * @rmtoll SCR CWUF4 LL_PWR_ClearFlag_WU4 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_WU4(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CWUF4); |
| } |
| |
| /** |
| * @brief Clear Wake-up Flag 3 |
| * @rmtoll SCR CWUF3 LL_PWR_ClearFlag_WU3 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_WU3(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CWUF3); |
| } |
| |
| /** |
| * @brief Clear Wake-up Flag 2 |
| * @rmtoll SCR CWUF2 LL_PWR_ClearFlag_WU2 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_WU2(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CWUF2); |
| } |
| |
| /** |
| * @brief Clear Wake-up Flag 1 |
| * @rmtoll SCR CWUF1 LL_PWR_ClearFlag_WU1 |
| * @retval None |
| */ |
| __STATIC_INLINE void LL_PWR_ClearFlag_WU1(void) |
| { |
| WRITE_REG(PWR->SCR, PWR_SCR_CWUF1); |
| } |
| |
| /** |
| * @brief Indicate whether VDDA voltage is below or above PVM4 threshold |
| * @rmtoll SR2 PVMO4 LL_PWR_IsActiveFlag_PVMO4 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_PVMO4(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_PVMO4); |
| |
| return ((temp == (PWR_SR2_PVMO4))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Indicate whether VDDA voltage is below or above PVM3 threshold |
| * @rmtoll SR2 PVMO3 LL_PWR_IsActiveFlag_PVMO3 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_PVMO3(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_PVMO3); |
| |
| return ((temp == (PWR_SR2_PVMO3))?1U:0U); |
| |
| } |
| |
| #if defined(PWR_SR2_PVMO2) |
| /** |
| * @brief Indicate whether VDDIO2 voltage is below or above PVM2 threshold |
| * @rmtoll SR2 PVMO2 LL_PWR_IsActiveFlag_PVMO2 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_PVMO2(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_PVMO2); |
| |
| return ((temp == (PWR_SR2_PVMO2))?1U:0U); |
| |
| } |
| #endif /* PWR_SR2_PVMO2 */ |
| |
| #if defined(PWR_SR2_PVMO1) |
| /** |
| * @brief Indicate whether VDDUSB voltage is below or above PVM1 threshold |
| * @rmtoll SR2 PVMO1 LL_PWR_IsActiveFlag_PVMO1 |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_PVMO1(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_PVMO1); |
| |
| return ((temp == (PWR_SR2_PVMO1))?1U:0U); |
| |
| } |
| #endif /* PWR_SR2_PVMO1 */ |
| |
| /** |
| * @brief Indicate whether VDD voltage is below or above the selected PVD threshold |
| * @rmtoll SR2 PVDO LL_PWR_IsActiveFlag_PVDO |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_PVDO(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_PVDO); |
| |
| return ((temp == (PWR_SR2_PVDO))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Indicate whether the regulator is ready in the selected voltage range or if its output voltage is still changing to the required voltage level |
| * @rmtoll SR2 VOSF LL_PWR_IsActiveFlag_VOS |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_VOS(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_VOSF); |
| |
| return ((temp == (PWR_SR2_VOSF))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Indicate whether the regulator is ready in main mode or is in low-power mode |
| * @note: Take care, return value "0" means the regulator is ready. Return value "1" means the output voltage range is still changing. |
| * @rmtoll SR2 REGLPF LL_PWR_IsActiveFlag_REGLPF |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_REGLPF(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_REGLPF); |
| |
| return ((temp == (PWR_SR2_REGLPF))?1U:0U); |
| |
| } |
| |
| /** |
| * @brief Indicate whether or not the low-power regulator is ready |
| * @rmtoll SR2 REGLPS LL_PWR_IsActiveFlag_REGLPS |
| * @retval State of bit (1 or 0). |
| */ |
| __STATIC_INLINE uint32_t LL_PWR_IsActiveFlag_REGLPS(void) |
| { |
| uint32_t temp; |
| temp = READ_BIT(PWR->SR2, PWR_SR2_REGLPS); |
| |
| return ((temp == (PWR_SR2_REGLPS))?1U:0U); |
| |
| } |
| |
| /** |
| * @} |
| */ |
| |
| #if defined(USE_FULL_LL_DRIVER) |
| /** @defgroup PWR_LL_EF_Init De-initialization function |
| * @{ |
| */ |
| ErrorStatus LL_PWR_DeInit(void); |
| /** |
| * @} |
| */ |
| #endif /* USE_FULL_LL_DRIVER */ |
| |
| /** @defgroup PWR_LL_EF_Legacy_Functions Legacy functions name |
| * @{ |
| */ |
| /* Old functions name kept for legacy purpose, to be replaced by the */ |
| /* current functions name. */ |
| #define LL_PWR_IsActiveFlag_VOSF LL_PWR_IsActiveFlag_VOS |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* defined(PWR) */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32G4xx_LL_PWR_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
