| /** |
| ****************************************************************************** |
| * @file stm32h7xx_hal_spi.h |
| * @author MCD Application Team |
| * @brief Header file of SPI HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32H7xx_HAL_SPI_H |
| #define STM32H7xx_HAL_SPI_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32h7xx_hal_def.h" |
| |
| /** @addtogroup STM32H7xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup SPI |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup SPI_Exported_Types SPI Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief SPI Configuration Structure definition |
| */ |
| typedef struct |
| { |
| uint32_t Mode; /*!< Specifies the SPI operating mode. |
| This parameter can be a value of @ref SPI_Mode */ |
| |
| uint32_t Direction; /*!< Specifies the SPI bidirectional mode state. |
| This parameter can be a value of @ref SPI_Direction */ |
| |
| uint32_t DataSize; /*!< Specifies the SPI data size. |
| This parameter can be a value of @ref SPI_Data_Size */ |
| |
| uint32_t CLKPolarity; /*!< Specifies the serial clock steady state. |
| This parameter can be a value of @ref SPI_Clock_Polarity */ |
| |
| uint32_t CLKPhase; /*!< Specifies the clock active edge for the bit capture. |
| This parameter can be a value of @ref SPI_Clock_Phase */ |
| |
| uint32_t NSS; /*!< Specifies whether the NSS signal is managed by |
| hardware (NSS pin) or by software using the SSI bit. |
| This parameter can be a value of @ref SPI_Slave_Select_Management */ |
| |
| uint32_t BaudRatePrescaler; /*!< Specifies the Baud Rate prescaler value which will be |
| used to configure the transmit and receive SCK clock. |
| This parameter can be a value of @ref SPI_BaudRate_Prescaler |
| @note The communication clock is derived from the master |
| clock. The slave clock does not need to be set. */ |
| |
| uint32_t FirstBit; /*!< Specifies whether data transfers start from MSB or LSB bit. |
| This parameter can be a value of @ref SPI_MSB_LSB_Transmission */ |
| |
| uint32_t TIMode; /*!< Specifies if the TI mode is enabled or not. |
| This parameter can be a value of @ref SPI_TI_Mode */ |
| |
| uint32_t CRCCalculation; /*!< Specifies if the CRC calculation is enabled or not. |
| This parameter can be a value of @ref SPI_CRC_Calculation */ |
| |
| uint32_t CRCPolynomial; /*!< Specifies the polynomial used for the CRC calculation. |
| This parameter must be an odd number between Min_Data = 0 and Max_Data = 65535 */ |
| |
| uint32_t CRCLength; /*!< Specifies the CRC Length used for the CRC calculation. |
| This parameter can be a value of @ref SPI_CRC_length */ |
| |
| uint32_t NSSPMode; /*!< Specifies whether the NSSP signal is enabled or not . |
| This parameter can be a value of @ref SPI_NSSP_Mode |
| This mode is activated by the SSOM bit in the SPIx_CR2 register and |
| it takes effect only if the SPI interface is configured as Motorola SPI |
| master (FRF=0). */ |
| |
| uint32_t NSSPolarity; /*!< Specifies which level of SS input/output external signal (present on SS pin) is |
| considered as active one. |
| This parameter can be a value of @ref SPI_NSS_Polarity */ |
| |
| uint32_t FifoThreshold; /*!< Specifies the FIFO threshold level. |
| This parameter can be a value of @ref SPI_Fifo_Threshold */ |
| |
| uint32_t TxCRCInitializationPattern; /*!< Specifies the transmitter CRC initialization Pattern used for the CRC calculation. |
| This parameter can be a value of @ref SPI_CRC_Calculation_Initialization_Pattern */ |
| |
| uint32_t RxCRCInitializationPattern; /*!< Specifies the receiver CRC initialization Pattern used for the CRC calculation. |
| This parameter can be a value of @ref SPI_CRC_Calculation_Initialization_Pattern */ |
| |
| uint32_t MasterSSIdleness; /*!< Specifies an extra delay, expressed in number of SPI clock cycle periods, inserted |
| additionally between active edge of SS and first data transaction start in master mode. |
| This parameter can be a value of @ref SPI_Master_SS_Idleness */ |
| |
| uint32_t MasterInterDataIdleness; /*!< Specifies minimum time delay (expressed in SPI clock cycles periods) inserted between |
| two consecutive data frames in master mode |
| This parameter can be a value of @ref SPI_Master_InterData_Idleness */ |
| |
| uint32_t MasterReceiverAutoSusp; /*!< Control continuous SPI transfer in master receiver mode and automatic management |
| in order to avoid overrun condition. |
| This parameter can be a value of @ref SPI_Master_RX_AutoSuspend*/ |
| |
| uint32_t MasterKeepIOState; /*!< Control of Alternate function GPIOs state |
| This parameter can be a value of @ref SPI_Master_Keep_IO_State */ |
| |
| uint32_t IOSwap; /*!< Invert MISO/MOSI alternate functions |
| This parameter can be a value of @ref SPI_IO_Swap */ |
| |
| } SPI_InitTypeDef; |
| |
| /** |
| * @brief HAL SPI State structure definition |
| */ |
| typedef enum |
| { |
| HAL_SPI_STATE_RESET = 0x00UL, /*!< Peripheral not Initialized */ |
| HAL_SPI_STATE_READY = 0x01UL, /*!< Peripheral Initialized and ready for use */ |
| HAL_SPI_STATE_BUSY = 0x02UL, /*!< an internal process is ongoing */ |
| HAL_SPI_STATE_BUSY_TX = 0x03UL, /*!< Data Transmission process is ongoing */ |
| HAL_SPI_STATE_BUSY_RX = 0x04UL, /*!< Data Reception process is ongoing */ |
| HAL_SPI_STATE_BUSY_TX_RX = 0x05UL, /*!< Data Transmission and Reception process is ongoing */ |
| HAL_SPI_STATE_ERROR = 0x06UL, /*!< SPI error state */ |
| HAL_SPI_STATE_ABORT = 0x07UL /*!< SPI abort is ongoing */ |
| } HAL_SPI_StateTypeDef; |
| |
| #if defined(USE_SPI_RELOAD_TRANSFER) |
| /** |
| * @brief SPI Reload Structure definition |
| */ |
| typedef struct |
| { |
| uint8_t *pTxBuffPtr; /*!< Pointer to SPI Tx transfer Buffer */ |
| |
| uint16_t TxXferSize; /*!< SPI Tx Transfer size to reload */ |
| |
| uint8_t *pRxBuffPtr; /*!< Pointer to SPI Rx transfer Buffer */ |
| |
| uint16_t RxXferSize; /*!< SPI Rx Transfer size to reload */ |
| |
| uint32_t Requested; /*!< SPI reload request */ |
| |
| } SPI_ReloadTypeDef; |
| #endif /* USE_HSPI_RELOAD_TRANSFER */ |
| |
| /** |
| * @brief SPI handle Structure definition |
| */ |
| typedef struct __SPI_HandleTypeDef |
| { |
| SPI_TypeDef *Instance; /*!< SPI registers base address */ |
| |
| SPI_InitTypeDef Init; /*!< SPI communication parameters */ |
| |
| uint8_t *pTxBuffPtr; /*!< Pointer to SPI Tx transfer Buffer */ |
| |
| uint16_t TxXferSize; /*!< SPI Tx Transfer size */ |
| |
| __IO uint16_t TxXferCount; /*!< SPI Tx Transfer Counter */ |
| |
| uint8_t *pRxBuffPtr; /*!< Pointer to SPI Rx transfer Buffer */ |
| |
| uint16_t RxXferSize; /*!< SPI Rx Transfer size */ |
| |
| __IO uint16_t RxXferCount; /*!< SPI Rx Transfer Counter */ |
| |
| uint32_t CRCSize; /*!< SPI CRC size used for the transfer */ |
| |
| void (*RxISR)(struct __SPI_HandleTypeDef *hspi); /*!< function pointer on Rx ISR */ |
| |
| void (*TxISR)(struct __SPI_HandleTypeDef *hspi); /*!< function pointer on Tx ISR */ |
| |
| DMA_HandleTypeDef *hdmatx; /*!< SPI Tx DMA Handle parameters */ |
| |
| DMA_HandleTypeDef *hdmarx; /*!< SPI Rx DMA Handle parameters */ |
| |
| HAL_LockTypeDef Lock; /*!< Locking object */ |
| |
| __IO HAL_SPI_StateTypeDef State; /*!< SPI communication state */ |
| |
| __IO uint32_t ErrorCode; /*!< SPI Error code */ |
| |
| #if defined(USE_SPI_RELOAD_TRANSFER) |
| |
| SPI_ReloadTypeDef Reload; /*!< SPI reload parameters */ |
| |
| #endif /* USE_HSPI_RELOAD_TRANSFER */ |
| |
| #if (USE_HAL_SPI_REGISTER_CALLBACKS == 1UL) |
| void (* TxCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Tx Completed callback */ |
| void (* RxCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Rx Completed callback */ |
| void (* TxRxCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI TxRx Completed callback */ |
| void (* TxHalfCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Tx Half Completed callback */ |
| void (* RxHalfCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Rx Half Completed callback */ |
| void (* TxRxHalfCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI TxRx Half Completed callback */ |
| void (* ErrorCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Error callback */ |
| void (* AbortCpltCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Abort callback */ |
| void (* MspInitCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Msp Init callback */ |
| void (* MspDeInitCallback)(struct __SPI_HandleTypeDef *hspi); /*!< SPI Msp DeInit callback */ |
| |
| #endif /* USE_HAL_SPI_REGISTER_CALLBACKS */ |
| } SPI_HandleTypeDef; |
| |
| #if (USE_HAL_SPI_REGISTER_CALLBACKS == 1UL) |
| /** |
| * @brief HAL SPI Callback ID enumeration definition |
| */ |
| typedef enum |
| { |
| HAL_SPI_TX_COMPLETE_CB_ID = 0x00UL, /*!< SPI Tx Completed callback ID */ |
| HAL_SPI_RX_COMPLETE_CB_ID = 0x01UL, /*!< SPI Rx Completed callback ID */ |
| HAL_SPI_TX_RX_COMPLETE_CB_ID = 0x02UL, /*!< SPI TxRx Completed callback ID */ |
| HAL_SPI_TX_HALF_COMPLETE_CB_ID = 0x03UL, /*!< SPI Tx Half Completed callback ID */ |
| HAL_SPI_RX_HALF_COMPLETE_CB_ID = 0x04UL, /*!< SPI Rx Half Completed callback ID */ |
| HAL_SPI_TX_RX_HALF_COMPLETE_CB_ID = 0x05UL, /*!< SPI TxRx Half Completed callback ID */ |
| HAL_SPI_ERROR_CB_ID = 0x06UL, /*!< SPI Error callback ID */ |
| HAL_SPI_ABORT_CB_ID = 0x07UL, /*!< SPI Abort callback ID */ |
| HAL_SPI_MSPINIT_CB_ID = 0x08UL, /*!< SPI Msp Init callback ID */ |
| HAL_SPI_MSPDEINIT_CB_ID = 0x09UL /*!< SPI Msp DeInit callback ID */ |
| |
| } HAL_SPI_CallbackIDTypeDef; |
| |
| /** |
| * @brief HAL SPI Callback pointer definition |
| */ |
| typedef void (*pSPI_CallbackTypeDef)(SPI_HandleTypeDef *hspi); /*!< pointer to an SPI callback function */ |
| |
| #endif /* USE_HAL_SPI_REGISTER_CALLBACKS */ |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| |
| /** @defgroup SPI_Exported_Constants SPI Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup SPI_FIFO_Type SPI FIFO Type |
| * @{ |
| */ |
| #define SPI_LOWEND_FIFO_SIZE 8UL |
| #define SPI_HIGHEND_FIFO_SIZE 16UL |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Error_Code SPI Error Codes |
| * @{ |
| */ |
| #define HAL_SPI_ERROR_NONE (0x00000000UL) /*!< No error */ |
| #define HAL_SPI_ERROR_MODF (0x00000001UL) /*!< MODF error */ |
| #define HAL_SPI_ERROR_CRC (0x00000002UL) /*!< CRC error */ |
| #define HAL_SPI_ERROR_OVR (0x00000004UL) /*!< OVR error */ |
| #define HAL_SPI_ERROR_FRE (0x00000008UL) /*!< FRE error */ |
| #define HAL_SPI_ERROR_DMA (0x00000010UL) /*!< DMA transfer error */ |
| #define HAL_SPI_ERROR_FLAG (0x00000020UL) /*!< Error on RXNE/TXE/BSY/FTLVL/FRLVL Flag */ |
| #define HAL_SPI_ERROR_ABORT (0x00000040UL) /*!< Error during SPI Abort procedure */ |
| #define HAL_SPI_ERROR_UDR (0x00000080UL) /*!< Underrun error */ |
| #define HAL_SPI_ERROR_TIMEOUT (0x00000100UL) /*!< Timeout error */ |
| #define HAL_SPI_ERROR_UNKNOW (0x00000200UL) /*!< Unknow error */ |
| #define HAL_SPI_ERROR_NOT_SUPPORTED (0x00000400UL) /*!< Requested operation not supported */ |
| #if (USE_HAL_SPI_REGISTER_CALLBACKS == 1UL) |
| #define HAL_SPI_ERROR_INVALID_CALLBACK (0x00000800UL) /*!< Invalid Callback error */ |
| #endif /* USE_HAL_SPI_REGISTER_CALLBACKS */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Mode SPI Mode |
| * @{ |
| */ |
| #define SPI_MODE_SLAVE (0x00000000UL) |
| #define SPI_MODE_MASTER SPI_CFG2_MASTER |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Direction SPI Direction Mode |
| * @{ |
| */ |
| #define SPI_DIRECTION_2LINES (0x00000000UL) |
| #define SPI_DIRECTION_2LINES_TXONLY SPI_CFG2_COMM_0 |
| #define SPI_DIRECTION_2LINES_RXONLY SPI_CFG2_COMM_1 |
| #define SPI_DIRECTION_1LINE SPI_CFG2_COMM |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Data_Size SPI Data Size |
| * @{ |
| */ |
| #define SPI_DATASIZE_4BIT (0x00000003UL) |
| #define SPI_DATASIZE_5BIT (0x00000004UL) |
| #define SPI_DATASIZE_6BIT (0x00000005UL) |
| #define SPI_DATASIZE_7BIT (0x00000006UL) |
| #define SPI_DATASIZE_8BIT (0x00000007UL) |
| #define SPI_DATASIZE_9BIT (0x00000008UL) |
| #define SPI_DATASIZE_10BIT (0x00000009UL) |
| #define SPI_DATASIZE_11BIT (0x0000000AUL) |
| #define SPI_DATASIZE_12BIT (0x0000000BUL) |
| #define SPI_DATASIZE_13BIT (0x0000000CUL) |
| #define SPI_DATASIZE_14BIT (0x0000000DUL) |
| #define SPI_DATASIZE_15BIT (0x0000000EUL) |
| #define SPI_DATASIZE_16BIT (0x0000000FUL) |
| #define SPI_DATASIZE_17BIT (0x00000010UL) |
| #define SPI_DATASIZE_18BIT (0x00000011UL) |
| #define SPI_DATASIZE_19BIT (0x00000012UL) |
| #define SPI_DATASIZE_20BIT (0x00000013UL) |
| #define SPI_DATASIZE_21BIT (0x00000014UL) |
| #define SPI_DATASIZE_22BIT (0x00000015UL) |
| #define SPI_DATASIZE_23BIT (0x00000016UL) |
| #define SPI_DATASIZE_24BIT (0x00000017UL) |
| #define SPI_DATASIZE_25BIT (0x00000018UL) |
| #define SPI_DATASIZE_26BIT (0x00000019UL) |
| #define SPI_DATASIZE_27BIT (0x0000001AUL) |
| #define SPI_DATASIZE_28BIT (0x0000001BUL) |
| #define SPI_DATASIZE_29BIT (0x0000001CUL) |
| #define SPI_DATASIZE_30BIT (0x0000001DUL) |
| #define SPI_DATASIZE_31BIT (0x0000001EUL) |
| #define SPI_DATASIZE_32BIT (0x0000001FUL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Clock_Polarity SPI Clock Polarity |
| * @{ |
| */ |
| #define SPI_POLARITY_LOW (0x00000000UL) |
| #define SPI_POLARITY_HIGH SPI_CFG2_CPOL |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Clock_Phase SPI Clock Phase |
| * @{ |
| */ |
| #define SPI_PHASE_1EDGE (0x00000000UL) |
| #define SPI_PHASE_2EDGE SPI_CFG2_CPHA |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Slave_Select_Management SPI Slave Select Management |
| * @{ |
| */ |
| #define SPI_NSS_SOFT SPI_CFG2_SSM |
| #define SPI_NSS_HARD_INPUT (0x00000000UL) |
| #define SPI_NSS_HARD_OUTPUT SPI_CFG2_SSOE |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_NSSP_Mode SPI NSS Pulse Mode |
| * @{ |
| */ |
| #define SPI_NSS_PULSE_DISABLE (0x00000000UL) |
| #define SPI_NSS_PULSE_ENABLE SPI_CFG2_SSOM |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_BaudRate_Prescaler SPI BaudRate Prescaler |
| * @{ |
| */ |
| #define SPI_BAUDRATEPRESCALER_2 (0x00000000UL) |
| #define SPI_BAUDRATEPRESCALER_4 (0x10000000UL) |
| #define SPI_BAUDRATEPRESCALER_8 (0x20000000UL) |
| #define SPI_BAUDRATEPRESCALER_16 (0x30000000UL) |
| #define SPI_BAUDRATEPRESCALER_32 (0x40000000UL) |
| #define SPI_BAUDRATEPRESCALER_64 (0x50000000UL) |
| #define SPI_BAUDRATEPRESCALER_128 (0x60000000UL) |
| #define SPI_BAUDRATEPRESCALER_256 (0x70000000UL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_MSB_LSB_Transmission SPI MSB LSB Transmission |
| * @{ |
| */ |
| #define SPI_FIRSTBIT_MSB (0x00000000UL) |
| #define SPI_FIRSTBIT_LSB SPI_CFG2_LSBFRST |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_TI_Mode SPI TI Mode |
| * @{ |
| */ |
| #define SPI_TIMODE_DISABLE (0x00000000UL) |
| #define SPI_TIMODE_ENABLE SPI_CFG2_SP_0 |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_CRC_Calculation SPI CRC Calculation |
| * @{ |
| */ |
| #define SPI_CRCCALCULATION_DISABLE (0x00000000UL) |
| #define SPI_CRCCALCULATION_ENABLE SPI_CFG1_CRCEN |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_CRC_length SPI CRC Length |
| * @{ |
| */ |
| #define SPI_CRC_LENGTH_DATASIZE (0x00000000UL) |
| #define SPI_CRC_LENGTH_4BIT (0x00030000UL) |
| #define SPI_CRC_LENGTH_5BIT (0x00040000UL) |
| #define SPI_CRC_LENGTH_6BIT (0x00050000UL) |
| #define SPI_CRC_LENGTH_7BIT (0x00060000UL) |
| #define SPI_CRC_LENGTH_8BIT (0x00070000UL) |
| #define SPI_CRC_LENGTH_9BIT (0x00080000UL) |
| #define SPI_CRC_LENGTH_10BIT (0x00090000UL) |
| #define SPI_CRC_LENGTH_11BIT (0x000A0000UL) |
| #define SPI_CRC_LENGTH_12BIT (0x000B0000UL) |
| #define SPI_CRC_LENGTH_13BIT (0x000C0000UL) |
| #define SPI_CRC_LENGTH_14BIT (0x000D0000UL) |
| #define SPI_CRC_LENGTH_15BIT (0x000E0000UL) |
| #define SPI_CRC_LENGTH_16BIT (0x000F0000UL) |
| #define SPI_CRC_LENGTH_17BIT (0x00100000UL) |
| #define SPI_CRC_LENGTH_18BIT (0x00110000UL) |
| #define SPI_CRC_LENGTH_19BIT (0x00120000UL) |
| #define SPI_CRC_LENGTH_20BIT (0x00130000UL) |
| #define SPI_CRC_LENGTH_21BIT (0x00140000UL) |
| #define SPI_CRC_LENGTH_22BIT (0x00150000UL) |
| #define SPI_CRC_LENGTH_23BIT (0x00160000UL) |
| #define SPI_CRC_LENGTH_24BIT (0x00170000UL) |
| #define SPI_CRC_LENGTH_25BIT (0x00180000UL) |
| #define SPI_CRC_LENGTH_26BIT (0x00190000UL) |
| #define SPI_CRC_LENGTH_27BIT (0x001A0000UL) |
| #define SPI_CRC_LENGTH_28BIT (0x001B0000UL) |
| #define SPI_CRC_LENGTH_29BIT (0x001C0000UL) |
| #define SPI_CRC_LENGTH_30BIT (0x001D0000UL) |
| #define SPI_CRC_LENGTH_31BIT (0x001E0000UL) |
| #define SPI_CRC_LENGTH_32BIT (0x001F0000UL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Fifo_Threshold SPI Fifo Threshold |
| * @{ |
| */ |
| #define SPI_FIFO_THRESHOLD_01DATA (0x00000000UL) |
| #define SPI_FIFO_THRESHOLD_02DATA (0x00000020UL) |
| #define SPI_FIFO_THRESHOLD_03DATA (0x00000040UL) |
| #define SPI_FIFO_THRESHOLD_04DATA (0x00000060UL) |
| #define SPI_FIFO_THRESHOLD_05DATA (0x00000080UL) |
| #define SPI_FIFO_THRESHOLD_06DATA (0x000000A0UL) |
| #define SPI_FIFO_THRESHOLD_07DATA (0x000000C0UL) |
| #define SPI_FIFO_THRESHOLD_08DATA (0x000000E0UL) |
| #define SPI_FIFO_THRESHOLD_09DATA (0x00000100UL) |
| #define SPI_FIFO_THRESHOLD_10DATA (0x00000120UL) |
| #define SPI_FIFO_THRESHOLD_11DATA (0x00000140UL) |
| #define SPI_FIFO_THRESHOLD_12DATA (0x00000160UL) |
| #define SPI_FIFO_THRESHOLD_13DATA (0x00000180UL) |
| #define SPI_FIFO_THRESHOLD_14DATA (0x000001A0UL) |
| #define SPI_FIFO_THRESHOLD_15DATA (0x000001C0UL) |
| #define SPI_FIFO_THRESHOLD_16DATA (0x000001E0UL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_CRC_Calculation_Initialization_Pattern SPI CRC Calculation Initialization Pattern |
| * @{ |
| */ |
| #define SPI_CRC_INITIALIZATION_ALL_ZERO_PATTERN (0x00000000UL) |
| #define SPI_CRC_INITIALIZATION_ALL_ONE_PATTERN (0x00000001UL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_NSS_Polarity SPI NSS Polarity |
| * @{ |
| */ |
| #define SPI_NSS_POLARITY_LOW (0x00000000UL) |
| #define SPI_NSS_POLARITY_HIGH SPI_CFG2_SSIOP |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Master_Keep_IO_State Keep IO State |
| * @{ |
| */ |
| #define SPI_MASTER_KEEP_IO_STATE_DISABLE (0x00000000UL) |
| #define SPI_MASTER_KEEP_IO_STATE_ENABLE SPI_CFG2_AFCNTR |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_IO_Swap Control SPI IO Swap |
| * @{ |
| */ |
| #define SPI_IO_SWAP_DISABLE (0x00000000UL) |
| #define SPI_IO_SWAP_ENABLE SPI_CFG2_IOSWP |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Master_SS_Idleness SPI Master SS Idleness |
| * @{ |
| */ |
| #define SPI_MASTER_SS_IDLENESS_00CYCLE (0x00000000UL) |
| #define SPI_MASTER_SS_IDLENESS_01CYCLE (0x00000001UL) |
| #define SPI_MASTER_SS_IDLENESS_02CYCLE (0x00000002UL) |
| #define SPI_MASTER_SS_IDLENESS_03CYCLE (0x00000003UL) |
| #define SPI_MASTER_SS_IDLENESS_04CYCLE (0x00000004UL) |
| #define SPI_MASTER_SS_IDLENESS_05CYCLE (0x00000005UL) |
| #define SPI_MASTER_SS_IDLENESS_06CYCLE (0x00000006UL) |
| #define SPI_MASTER_SS_IDLENESS_07CYCLE (0x00000007UL) |
| #define SPI_MASTER_SS_IDLENESS_08CYCLE (0x00000008UL) |
| #define SPI_MASTER_SS_IDLENESS_09CYCLE (0x00000009UL) |
| #define SPI_MASTER_SS_IDLENESS_10CYCLE (0x0000000AUL) |
| #define SPI_MASTER_SS_IDLENESS_11CYCLE (0x0000000BUL) |
| #define SPI_MASTER_SS_IDLENESS_12CYCLE (0x0000000CUL) |
| #define SPI_MASTER_SS_IDLENESS_13CYCLE (0x0000000DUL) |
| #define SPI_MASTER_SS_IDLENESS_14CYCLE (0x0000000EUL) |
| #define SPI_MASTER_SS_IDLENESS_15CYCLE (0x0000000FUL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Master_InterData_Idleness SPI Master Inter-Data Idleness |
| * @{ |
| */ |
| #define SPI_MASTER_INTERDATA_IDLENESS_00CYCLE (0x00000000UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_01CYCLE (0x00000010UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_02CYCLE (0x00000020UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_03CYCLE (0x00000030UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_04CYCLE (0x00000040UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_05CYCLE (0x00000050UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_06CYCLE (0x00000060UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_07CYCLE (0x00000070UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_08CYCLE (0x00000080UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_09CYCLE (0x00000090UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_10CYCLE (0x000000A0UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_11CYCLE (0x000000B0UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_12CYCLE (0x000000C0UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_13CYCLE (0x000000D0UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_14CYCLE (0x000000E0UL) |
| #define SPI_MASTER_INTERDATA_IDLENESS_15CYCLE (0x000000F0UL) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Master_RX_AutoSuspend SPI Master Receiver AutoSuspend |
| * @{ |
| */ |
| #define SPI_MASTER_RX_AUTOSUSP_DISABLE (0x00000000UL) |
| #define SPI_MASTER_RX_AUTOSUSP_ENABLE SPI_CR1_MASRX |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Underrun_Detection SPI Underrun Detection |
| * @{ |
| */ |
| #define SPI_UNDERRUN_DETECT_BEGIN_DATA_FRAME (0x00000000UL) |
| #define SPI_UNDERRUN_DETECT_END_DATA_FRAME SPI_CFG1_UDRDET_0 |
| #define SPI_UNDERRUN_DETECT_BEGIN_ACTIVE_NSS SPI_CFG1_UDRDET_1 |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Underrun_Behaviour SPI Underrun Behavior |
| * @{ |
| */ |
| #define SPI_UNDERRUN_BEHAV_REGISTER_PATTERN (0x00000000UL) |
| #define SPI_UNDERRUN_BEHAV_LAST_RECEIVED SPI_CFG1_UDRCFG_0 |
| #define SPI_UNDERRUN_BEHAV_LAST_TRANSMITTED SPI_CFG1_UDRCFG_1 |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Interrupt_definition SPI Interrupt Definition |
| * @{ |
| */ |
| #define SPI_IT_RXP SPI_IER_RXPIE |
| #define SPI_IT_TXP SPI_IER_TXPIE |
| #define SPI_IT_DXP SPI_IER_DXPIE |
| #define SPI_IT_EOT SPI_IER_EOTIE |
| #define SPI_IT_TXTF SPI_IER_TXTFIE |
| #define SPI_IT_UDR SPI_IER_UDRIE |
| #define SPI_IT_OVR SPI_IER_OVRIE |
| #define SPI_IT_CRCERR SPI_IER_CRCEIE |
| #define SPI_IT_FRE SPI_IER_TIFREIE |
| #define SPI_IT_MODF SPI_IER_MODFIE |
| #define SPI_IT_TSERF SPI_IER_TSERFIE |
| #define SPI_IT_ERR (SPI_IT_UDR | SPI_IT_OVR | SPI_IT_FRE | SPI_IT_MODF | SPI_IT_CRCERR) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_Flags_definition SPI Flags Definition |
| * @{ |
| */ |
| #define SPI_FLAG_RXP SPI_SR_RXP /* SPI status flag : Rx-Packet available flag */ |
| #define SPI_FLAG_TXP SPI_SR_TXP /* SPI status flag : Tx-Packet space available flag */ |
| #define SPI_FLAG_DXP SPI_SR_DXP /* SPI status flag : Duplex Packet flag */ |
| #define SPI_FLAG_EOT SPI_SR_EOT /* SPI status flag : End of transfer flag */ |
| #define SPI_FLAG_TXTF SPI_SR_TXTF /* SPI status flag : Transmission Transfer Filled flag */ |
| #define SPI_FLAG_UDR SPI_SR_UDR /* SPI Error flag : Underrun flag */ |
| #define SPI_FLAG_OVR SPI_SR_OVR /* SPI Error flag : Overrun flag */ |
| #define SPI_FLAG_CRCERR SPI_SR_CRCE /* SPI Error flag : CRC error flag */ |
| #define SPI_FLAG_FRE SPI_SR_TIFRE /* SPI Error flag : TI mode frame format error flag */ |
| #define SPI_FLAG_MODF SPI_SR_MODF /* SPI Error flag : Mode fault flag */ |
| #define SPI_FLAG_TSERF SPI_SR_TSERF /* SPI status flag : Additional number of data reloaded flag */ |
| #define SPI_FLAG_SUSP SPI_SR_SUSP /* SPI status flag : Transfer suspend complete flag */ |
| #define SPI_FLAG_TXC SPI_SR_TXC /* SPI status flag : TxFIFO transmission complete flag */ |
| #define SPI_FLAG_FRLVL SPI_SR_RXPLVL /* SPI status flag : Fifo reception level flag */ |
| #define SPI_FLAG_RXWNE SPI_SR_RXWNE /* SPI status flag : RxFIFO word not empty flag */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SPI_reception_fifo_status_level SPI Reception FIFO Status Level |
| * @{ |
| */ |
| #define SPI_RX_FIFO_0PACKET (0x00000000UL) /* 0 or multiple of 4 packets available in the RxFIFO */ |
| #define SPI_RX_FIFO_1PACKET (SPI_SR_RXPLVL_0) |
| #define SPI_RX_FIFO_2PACKET (SPI_SR_RXPLVL_1) |
| #define SPI_RX_FIFO_3PACKET (SPI_SR_RXPLVL_1 | SPI_SR_RXPLVL_0) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup SPI_Exported_Macros SPI Exported Macros |
| * @{ |
| */ |
| |
| /** @brief Reset SPI handle state. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, 3, 4, 5 or 6 to select the SPI peripheral. |
| * @retval None |
| */ |
| #if (USE_HAL_SPI_REGISTER_CALLBACKS == 1UL) |
| #define __HAL_SPI_RESET_HANDLE_STATE(__HANDLE__) do{ \ |
| (__HANDLE__)->State = HAL_SPI_STATE_RESET; \ |
| (__HANDLE__)->MspInitCallback = NULL; \ |
| (__HANDLE__)->MspDeInitCallback = NULL; \ |
| } while(0) |
| #else |
| #define __HAL_SPI_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SPI_STATE_RESET) |
| #endif |
| |
| /** @brief Enable the specified SPI interrupts. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, 3, 4, 5 or 6 to select the SPI peripheral. |
| * @param __INTERRUPT__: specifies the interrupt source to enable or disable. |
| * This parameter can be one of the following values: |
| * @arg SPI_IT_RXP : Rx-Packet available interrupt |
| * @arg SPI_IT_TXP : Tx-Packet space available interrupt |
| * @arg SPI_IT_DXP : Duplex Packet interrupt |
| * @arg SPI_IT_EOT : End of transfer interrupt |
| * @arg SPI_IT_TXTF : Transmission Transfer Filled interrupt |
| * @arg SPI_IT_UDR : Underrun interrupt |
| * @arg SPI_IT_OVR : Overrun interrupt |
| * @arg SPI_IT_CRCERR : CRC error interrupt |
| * @arg SPI_IT_FRE : TI mode frame format error interrupt |
| * @arg SPI_IT_MODF : Mode fault interrupt |
| * @arg SPI_IT_TSERF : Additional number of data reloaded interrupt |
| * @arg SPI_IT_ERR : Error interrupt |
| * @retval None |
| */ |
| #define __HAL_SPI_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->IER |= (__INTERRUPT__)) |
| |
| /** @brief Disable the specified SPI interrupts. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, 3, 4, 5 or 6 to select the SPI peripheral. |
| * @param __INTERRUPT__: specifies the interrupt source to enable or disable. |
| * This parameter can be one of the following values: |
| * @arg SPI_IT_RXP : Rx-Packet available interrupt |
| * @arg SPI_IT_TXP : Tx-Packet space available interrupt |
| * @arg SPI_IT_DXP : Duplex Packet interrupt |
| * @arg SPI_IT_EOT : End of transfer interrupt |
| * @arg SPI_IT_TXTF : Transmission Transfer Filled interrupt |
| * @arg SPI_IT_UDR : Underrun interrupt |
| * @arg SPI_IT_OVR : Overrun interrupt |
| * @arg SPI_IT_CRCERR : CRC error interrupt |
| * @arg SPI_IT_FRE : TI mode frame format error interrupt |
| * @arg SPI_IT_MODF : Mode fault interrupt |
| * @arg SPI_IT_TSERF : Additional number of data reloaded interrupt |
| * @arg SPI_IT_ERR : Error interrupt |
| * @retval None |
| */ |
| #define __HAL_SPI_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->IER &= (~(__INTERRUPT__))) |
| |
| /** @brief Check whether the specified SPI interrupt source is enabled or not. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, 3, 4, 5 or 6 to select the SPI peripheral. |
| * @param __INTERRUPT__: specifies the SPI interrupt source to check. |
| * This parameter can be one of the following values: |
| * @arg SPI_IT_RXP : Rx-Packet available interrupt |
| * @arg SPI_IT_TXP : Tx-Packet space available interrupt |
| * @arg SPI_IT_DXP : Duplex Packet interrupt |
| * @arg SPI_IT_EOT : End of transfer interrupt |
| * @arg SPI_IT_TXTF : Transmission Transfer Filled interrupt |
| * @arg SPI_IT_UDR : Underrun interrupt |
| * @arg SPI_IT_OVR : Overrun interrupt |
| * @arg SPI_IT_CRCERR : CRC error interrupt |
| * @arg SPI_IT_FRE : TI mode frame format error interrupt |
| * @arg SPI_IT_MODF : Mode fault interrupt |
| * @arg SPI_IT_TSERF : Additional number of data reloaded interrupt |
| * @arg SPI_IT_ERR : Error interrupt |
| * @retval The new state of __IT__ (TRUE or FALSE). |
| */ |
| #define __HAL_SPI_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET) |
| |
| /** @brief Check whether the specified SPI flag is set or not. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, 3, 4, 5 or 6 to select the SPI peripheral. |
| * @param __FLAG__: specifies the flag to check. |
| * This parameter can be one of the following values: |
| * @arg SPI_FLAG_RXP : Rx-Packet available flag |
| * @arg SPI_FLAG_TXP : Tx-Packet space available flag |
| * @arg SPI_FLAG_DXP : Duplex Packet flag |
| * @arg SPI_FLAG_EOT : End of transfer flag |
| * @arg SPI_FLAG_TXTF : Transmission Transfer Filled flag |
| * @arg SPI_FLAG_UDR : Underrun flag |
| * @arg SPI_FLAG_OVR : Overrun flag |
| * @arg SPI_FLAG_CRCERR : CRC error flag |
| * @arg SPI_FLAG_FRE : TI mode frame format error flag |
| * @arg SPI_FLAG_MODF : Mode fault flag |
| * @arg SPI_FLAG_TSERF : Additional number of data reloaded flag |
| * @arg SPI_FLAG_SUSP : Transfer suspend complete flag |
| * @arg SPI_FLAG_TXC : TxFIFO transmission complete flag |
| * @arg SPI_FLAG_FRLVL : Fifo reception level flag |
| * @arg SPI_FLAG_RXWNE : RxFIFO word not empty flag |
| * @retval The new state of __FLAG__ (TRUE or FALSE). |
| */ |
| #define __HAL_SPI_GET_FLAG(__HANDLE__, __FLAG__) ((((__HANDLE__)->Instance->SR) & (__FLAG__)) == (__FLAG__)) |
| |
| /** @brief Clear the SPI CRCERR pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_CRCERRFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_CRCEC) |
| |
| /** @brief Clear the SPI MODF pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_MODFFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , (uint32_t)(SPI_IFCR_MODFC)); |
| |
| /** @brief Clear the SPI OVR pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_OVRFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_OVRC) |
| |
| /** @brief Clear the SPI FRE pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_FREFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_TIFREC) |
| |
| /** @brief Clear the SPI UDR pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_UDRFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_UDRC) |
| |
| /** @brief Clear the SPI EOT pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_EOTFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_EOTC) |
| |
| /** @brief Clear the SPI UDR pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_TXTFFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_TXTFC) |
| |
| /** @brief Clear the SPI SUSP pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_SUSPFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_SUSPC) |
| |
| /** @brief Clear the SPI TSERF pending flag. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_CLEAR_TSERFFLAG(__HANDLE__) SET_BIT((__HANDLE__)->Instance->IFCR , SPI_IFCR_TSERFC) |
| |
| /** @brief Enable the SPI peripheral. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR1 , SPI_CR1_SPE) |
| |
| /** @brief Disable the SPI peripheral. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * @retval None |
| */ |
| #define __HAL_SPI_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR1 , SPI_CR1_SPE) |
| /** |
| * @} |
| */ |
| |
| |
| /* Include SPI HAL Extension module */ |
| #include "stm32h7xx_hal_spi_ex.h" |
| |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup SPI_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup SPI_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @{ |
| */ |
| /* Initialization/de-initialization functions ********************************/ |
| HAL_StatusTypeDef HAL_SPI_Init(SPI_HandleTypeDef *hspi); |
| HAL_StatusTypeDef HAL_SPI_DeInit(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_MspInit(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_MspDeInit(SPI_HandleTypeDef *hspi); |
| |
| /* Callbacks Register/UnRegister functions ***********************************/ |
| #if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U) |
| HAL_StatusTypeDef HAL_SPI_RegisterCallback(SPI_HandleTypeDef *hspi, HAL_SPI_CallbackIDTypeDef CallbackID, pSPI_CallbackTypeDef pCallback); |
| HAL_StatusTypeDef HAL_SPI_UnRegisterCallback(SPI_HandleTypeDef *hspi, HAL_SPI_CallbackIDTypeDef CallbackID); |
| #endif /* USE_HAL_SPI_REGISTER_CALLBACKS */ |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup SPI_Exported_Functions_Group2 IO operation functions |
| * @{ |
| */ |
| /* I/O operation functions ***************************************************/ |
| HAL_StatusTypeDef HAL_SPI_Transmit(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_SPI_Receive(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_SPI_TransmitReceive(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, |
| uint32_t Timeout); |
| HAL_StatusTypeDef HAL_SPI_Transmit_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size); |
| HAL_StatusTypeDef HAL_SPI_Receive_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size); |
| HAL_StatusTypeDef HAL_SPI_TransmitReceive_IT(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size); |
| |
| HAL_StatusTypeDef HAL_SPI_Transmit_DMA(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size); |
| HAL_StatusTypeDef HAL_SPI_Receive_DMA(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size); |
| HAL_StatusTypeDef HAL_SPI_TransmitReceive_DMA(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size); |
| |
| #if defined(USE_SPI_RELOAD_TRANSFER) |
| HAL_StatusTypeDef HAL_SPI_Reload_Transmit_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size); |
| HAL_StatusTypeDef HAL_SPI_Reload_Receive_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size); |
| HAL_StatusTypeDef HAL_SPI_Reload_TransmitReceive_IT(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size); |
| #endif /* USE_HSPI_RELOAD_TRANSFER */ |
| |
| HAL_StatusTypeDef HAL_SPI_DMAPause(SPI_HandleTypeDef *hspi); |
| HAL_StatusTypeDef HAL_SPI_DMAResume(SPI_HandleTypeDef *hspi); |
| HAL_StatusTypeDef HAL_SPI_DMAStop(SPI_HandleTypeDef *hspi); |
| |
| /* Transfer Abort functions */ |
| HAL_StatusTypeDef HAL_SPI_Abort(SPI_HandleTypeDef *hspi); |
| HAL_StatusTypeDef HAL_SPI_Abort_IT(SPI_HandleTypeDef *hspi); |
| |
| void HAL_SPI_IRQHandler(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_TxCpltCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_RxCpltCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_TxRxCpltCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_TxHalfCpltCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_RxHalfCpltCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_TxRxHalfCpltCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_ErrorCallback(SPI_HandleTypeDef *hspi); |
| void HAL_SPI_AbortCpltCallback(SPI_HandleTypeDef *hspi); |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup SPI_Exported_Functions_Group3 Peripheral State and Errors functions |
| * @{ |
| */ |
| |
| /* Peripheral State and Error functions ***************************************/ |
| HAL_SPI_StateTypeDef HAL_SPI_GetState(SPI_HandleTypeDef *hspi); |
| uint32_t HAL_SPI_GetError(SPI_HandleTypeDef *hspi); |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup SPI_Private_Macros SPI Private Macros |
| * @{ |
| */ |
| |
| /** @brief Set the SPI transmit-only mode. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral. |
| * @retval None |
| */ |
| #define SPI_1LINE_TX(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR1 , SPI_CR1_HDDIR) |
| |
| /** @brief Set the SPI receive-only mode. |
| * @param __HANDLE__: specifies the SPI Handle. |
| * This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral. |
| * @retval None |
| */ |
| #define SPI_1LINE_RX(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR1 ,SPI_CR1_HDDIR) |
| |
| #define IS_SPI_MODE(MODE) (((MODE) == SPI_MODE_SLAVE) || \ |
| ((MODE) == SPI_MODE_MASTER)) |
| |
| #define IS_SPI_DIRECTION(MODE) (((MODE) == SPI_DIRECTION_2LINES) || \ |
| ((MODE) == SPI_DIRECTION_2LINES_RXONLY) || \ |
| ((MODE) == SPI_DIRECTION_1LINE) || \ |
| ((MODE) == SPI_DIRECTION_2LINES_TXONLY)) |
| |
| #define IS_SPI_DIRECTION_2LINES(MODE) ((MODE) == SPI_DIRECTION_2LINES) |
| |
| #define IS_SPI_DIRECTION_2LINES_OR_1LINE_2LINES_TXONLY(MODE) ( \ |
| ((MODE) == SPI_DIRECTION_2LINES)|| \ |
| ((MODE) == SPI_DIRECTION_1LINE) || \ |
| ((MODE) == SPI_DIRECTION_2LINES_TXONLY)) |
| |
| #define IS_SPI_DIRECTION_2LINES_OR_1LINE_2LINES_RXONLY(MODE) ( \ |
| ((MODE) == SPI_DIRECTION_2LINES)|| \ |
| ((MODE) == SPI_DIRECTION_1LINE) || \ |
| ((MODE) == SPI_DIRECTION_2LINES_RXONLY)) |
| |
| #define IS_SPI_DATASIZE(DATASIZE) (((DATASIZE) == SPI_DATASIZE_32BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_31BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_30BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_29BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_28BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_27BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_26BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_25BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_24BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_23BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_22BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_21BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_20BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_22BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_19BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_18BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_17BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_16BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_15BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_14BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_13BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_12BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_11BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_10BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_9BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_8BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_7BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_6BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_5BIT) || \ |
| ((DATASIZE) == SPI_DATASIZE_4BIT)) |
| |
| #define IS_SPI_FIFOTHRESHOLD(THRESHOLD) (((THRESHOLD) == SPI_FIFO_THRESHOLD_01DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_02DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_03DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_04DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_05DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_06DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_07DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_08DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_09DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_10DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_11DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_12DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_13DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_14DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_15DATA) || \ |
| ((THRESHOLD) == SPI_FIFO_THRESHOLD_16DATA)) |
| |
| #define IS_SPI_CPOL(CPOL) (((CPOL) == SPI_POLARITY_LOW) || \ |
| ((CPOL) == SPI_POLARITY_HIGH)) |
| |
| #define IS_SPI_CPHA(CPHA) (((CPHA) == SPI_PHASE_1EDGE) || \ |
| ((CPHA) == SPI_PHASE_2EDGE)) |
| |
| #define IS_SPI_NSS(NSS) (((NSS) == SPI_NSS_SOFT) || \ |
| ((NSS) == SPI_NSS_HARD_INPUT) || \ |
| ((NSS) == SPI_NSS_HARD_OUTPUT)) |
| |
| #define IS_SPI_NSSP(NSSP) (((NSSP) == SPI_NSS_PULSE_ENABLE) || \ |
| ((NSSP) == SPI_NSS_PULSE_DISABLE)) |
| |
| #define IS_SPI_BAUDRATE_PRESCALER(PRESCALER) (((PRESCALER) == SPI_BAUDRATEPRESCALER_2) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_4) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_8) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_16) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_32) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_64) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_128) || \ |
| ((PRESCALER) == SPI_BAUDRATEPRESCALER_256)) |
| |
| #define IS_SPI_FIRST_BIT(BIT) (((BIT) == SPI_FIRSTBIT_MSB) || \ |
| ((BIT) == SPI_FIRSTBIT_LSB)) |
| |
| #define IS_SPI_TIMODE(MODE) (((MODE) == SPI_TIMODE_DISABLE) || \ |
| ((MODE) == SPI_TIMODE_ENABLE)) |
| |
| #define IS_SPI_CRC_CALCULATION(CALCULATION) (((CALCULATION) == SPI_CRCCALCULATION_DISABLE) || \ |
| ((CALCULATION) == SPI_CRCCALCULATION_ENABLE)) |
| |
| #define IS_SPI_CRC_INITIALIZATION_PATTERN(PATTERN) (((PATTERN) == SPI_CRC_INITIALIZATION_ALL_ZERO_PATTERN) || \ |
| ((PATTERN) == SPI_CRC_INITIALIZATION_ALL_ONE_PATTERN)) |
| |
| #define IS_SPI_CRC_LENGTH(LENGTH) (((LENGTH) == SPI_CRC_LENGTH_DATASIZE) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_32BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_31BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_30BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_29BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_28BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_27BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_26BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_25BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_24BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_23BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_22BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_21BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_20BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_19BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_18BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_17BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_16BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_15BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_14BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_13BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_12BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_11BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_10BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_9BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_8BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_7BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_6BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_5BIT) || \ |
| ((LENGTH) == SPI_CRC_LENGTH_4BIT)) |
| |
| #define IS_SPI_CRC_POLYNOMIAL(POLYNOMIAL) ((POLYNOMIAL) >= 0x1UL) |
| |
| #define IS_SPI_UNDERRUN_DETECTION(MODE) (((MODE) == SPI_UNDERRUN_DETECT_BEGIN_DATA_FRAME) || \ |
| ((MODE) == SPI_UNDERRUN_DETECT_END_DATA_FRAME) || \ |
| ((MODE) == SPI_UNDERRUN_DETECT_BEGIN_ACTIVE_NSS)) |
| |
| #define IS_SPI_UNDERRUN_BEHAVIOUR(MODE) (((MODE) == SPI_UNDERRUN_BEHAV_REGISTER_PATTERN) || \ |
| ((MODE) == SPI_UNDERRUN_BEHAV_LAST_RECEIVED) || \ |
| ((MODE) == SPI_UNDERRUN_BEHAV_LAST_TRANSMITTED)) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32H7xx_HAL_SPI_H */ |
| |
| /** |
| * @} |
| */ |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
