Google Git
Sign in
pigweed / third_party / github / STMicroelectronics / stm32h7xx_hal_driver / aeda37fdec846e5d132ba4bd5d1b5a78757e8354 / . / Inc / stm32h7xx_hal_adc.h
blob: d74c0e25235764b034b575d0e75ffba42838a7d2 [file] [log] [blame]
/**
******************************************************************************
* @file stm32h7xx_hal_adc.h
* @author MCD Application Team
* @brief Header file of ADC HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32H7xx_HAL_ADC_H
#define STM32H7xx_HAL_ADC_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32h7xx_hal_def.h"
/* Include low level driver */
#include "stm32h7xx_ll_adc.h"
/** @addtogroup STM32H7xx_HAL_Driver
* @{
*/
/** @addtogroup ADC
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup ADC_Exported_Types ADC Exported Types
* @{
*/
/**
* @brief ADC group regular oversampling structure definition
*/
typedef struct
{
uint32_t Ratio; /*!< Configures the oversampling ratio.
This parameter can be a value between 1 and 1024 */
uint32_t RightBitShift; /*!< Configures the division coefficient for the Oversampler.
This parameter can be a value of @ref ADC_HAL_EC_OVS_SHIFT */
uint32_t TriggeredMode; /*!< Selects the regular triggered oversampling mode.
This parameter can be a value of @ref ADC_HAL_EC_OVS_DISCONT_MODE */
uint32_t OversamplingStopReset; /*!< Selects the regular oversampling mode.
The oversampling is either temporary stopped or reset upon an injected
sequence interruption.
If oversampling is enabled on both regular and injected groups, this parameter
is discarded and forced to setting "ADC_REGOVERSAMPLING_RESUMED_MODE"
(the oversampling buffer is zeroed during injection sequence).
This parameter can be a value of @ref ADC_HAL_EC_OVS_SCOPE_REG */
} ADC_OversamplingTypeDef;
/**
* @brief Structure definition of ADC instance and ADC group regular.
* @note Parameters of this structure are shared within 2 scopes:
* - Scope entire ADC (affects ADC groups regular and injected): ClockPrescaler, Resolution, DataAlign,
* ScanConvMode, EOCSelection, LowPowerAutoWait.
* - Scope ADC group regular: ContinuousConvMode, NbrOfConversion, DiscontinuousConvMode, NbrOfDiscConversion,
* ExternalTrigConv, ExternalTrigConvEdge, DMAContinuousRequests, Overrun, OversamplingMode, Oversampling.
* @note The setting of these parameters by function HAL_ADC_Init() is conditioned to ADC state.
* ADC state can be either:
* - For all parameters: ADC disabled
* - For all parameters except 'LowPowerAutoWait', 'DMAContinuousRequests' and 'Oversampling': ADC enabled without conversion on going on group regular.
* - For parameters 'LowPowerAutoWait' and 'DMAContinuousRequests': ADC enabled without conversion on going on groups regular and injected.
* If ADC is not in the appropriate state to modify some parameters, these parameters setting is bypassed
* without error reporting (as it can be the expected behavior in case of intended action to update another parameter
* (which fulfills the ADC state condition) on the fly).
*/
typedef struct
{
uint32_t ClockPrescaler; /*!< Select ADC clock source (synchronous clock derived from APB clock or asynchronous clock derived from system clock or PLL (Refer to reference manual for list of clocks available)) and clock prescaler.
This parameter can be a value of @ref ADC_HAL_EC_COMMON_CLOCK_SOURCE.
Note: The ADC clock configuration is common to all ADC instances.
Note: In case of usage of channels on injected group, ADC frequency should be lower than AHB clock frequency /4 for resolution 12 or 10 bits,
AHB clock frequency /3 for resolution 8 bits, AHB clock frequency /2 for resolution 6 bits.
Note: In case of synchronous clock mode based on HCLK/1, the configuration must be enabled only
if the system clock has a 50% duty clock cycle (APB prescaler configured inside RCC
must be bypassed and PCLK clock must have 50% duty cycle). Refer to reference manual for details.
Note: In case of usage of asynchronous clock, the selected clock must be preliminarily enabled at RCC top level.
Note: This parameter can be modified only if all ADC instances are disabled. */
uint32_t Resolution; /*!< Configure the ADC resolution.
This parameter can be a value of @ref ADC_HAL_EC_RESOLUTION */
uint32_t ScanConvMode; /*!< Configure the sequencer of ADC groups regular and injected.
This parameter can be associated to parameter 'DiscontinuousConvMode' to have main sequence subdivided in successive parts.
If disabled: Conversion is performed in single mode (one channel converted, the one defined in rank 1).
Parameters 'NbrOfConversion' and 'InjectedNbrOfConversion' are discarded (equivalent to set to 1).
If enabled: Conversions are performed in sequence mode (multiple ranks defined by 'NbrOfConversion' or 'InjectedNbrOfConversion' and rank of each channel in sequencer).
Scan direction is upward: from rank 1 to rank 'n'.
This parameter can be a value of @ref ADC_Scan_mode */
uint32_t EOCSelection; /*!< Specify which EOC (End Of Conversion) flag is used for conversion by polling and interruption: end of unitary conversion or end of sequence conversions.
This parameter can be a value of @ref ADC_EOCSelection. */
FunctionalState LowPowerAutoWait; /*!< Select the dynamic low power Auto Delay: new conversion start only when the previous
conversion (for ADC group regular) or previous sequence (for ADC group injected) has been retrieved by user software,
using function HAL_ADC_GetValue() or HAL_ADCEx_InjectedGetValue().
This feature automatically adapts the frequency of ADC conversions triggers to the speed of the system that reads the data. Moreover, this avoids risk of overrun
for low frequency applications.
This parameter can be set to ENABLE or DISABLE.
Note: Do not use with interruption or DMA (HAL_ADC_Start_IT(), HAL_ADC_Start_DMA()) since they clear immediately the EOC flag
to free the IRQ vector sequencer.
Do use with polling: 1. Start conversion with HAL_ADC_Start(), 2. Later on, when ADC conversion data is needed:
use HAL_ADC_PollForConversion() to ensure that conversion is completed and HAL_ADC_GetValue() to retrieve conversion result and trig another conversion start.
(in case of usage of ADC group injected, use the equivalent functions HAL_ADCExInjected_Start(), HAL_ADCEx_InjectedGetValue(), ...). */
FunctionalState ContinuousConvMode; /*!< Specify whether the conversion is performed in single mode (one conversion) or continuous mode for ADC group regular,
after the first ADC conversion start trigger occurred (software start or external trigger).
This parameter can be set to ENABLE or DISABLE. */
uint32_t NbrOfConversion; /*!< Specify the number of ranks that will be converted within the regular group sequencer.
To use the regular group sequencer and convert several ranks, parameter 'ScanConvMode' must be enabled.
This parameter must be a number between Min_Data = 1 and Max_Data = 16.
Note: This parameter must be modified when no conversion is on going on regular group (ADC disabled, or ADC enabled without
continuous mode or external trigger that could launch a conversion). */
FunctionalState DiscontinuousConvMode; /*!< Specify whether the conversions sequence of ADC group regular is performed in Complete-sequence/Discontinuous-sequence
(main sequence subdivided in successive parts).
Discontinuous mode is used only if sequencer is enabled (parameter 'ScanConvMode'). If sequencer is disabled, this parameter is discarded.
Discontinuous mode can be enabled only if continuous mode is disabled. If continuous mode is enabled, this parameter setting is discarded.
This parameter can be set to ENABLE or DISABLE. */
uint32_t NbrOfDiscConversion; /*!< Specifies the number of discontinuous conversions in which the main sequence of ADC group regular (parameter NbrOfConversion) will be subdivided.
If parameter 'DiscontinuousConvMode' is disabled, this parameter is discarded.
This parameter must be a number between Min_Data = 1 and Max_Data = 8. */
uint32_t ExternalTrigConv; /*!< Select the external event source used to trigger ADC group regular conversion start.
If set to ADC_SOFTWARE_START, external triggers are disabled and software trigger is used instead.
This parameter can be a value of @ref ADC_regular_external_trigger_source.
Caution: external trigger source is common to all ADC instances. */
uint32_t ExternalTrigConvEdge; /*!< Select the external event edge used to trigger ADC group regular conversion start.
If trigger source is set to ADC_SOFTWARE_START, this parameter is discarded.
This parameter can be a value of @ref ADC_regular_external_trigger_edge */
uint32_t ConversionDataManagement; /*!< Specifies whether the Data conversion data is managed: using the DMA (oneshot or circular), or stored in the DR register or transfered to DFSDM register.
Note: In continuous mode, DMA must be configured in circular mode. Otherwise an overrun will be triggered when DMA buffer maximum pointer is reached.
This parameter can be a value of @ref ADC_ConversionDataManagement.
Note: This parameter must be modified when no conversion is on going on both regular and injected groups
(ADC disabled, or ADC enabled without continuous mode or external trigger that could launch a conversion). */
uint32_t Overrun; /*!< Select the behavior in case of overrun: data overwritten or preserved (default).
This parameter applies to ADC group regular only.
This parameter can be a value of @ref ADC_HAL_EC_REG_OVR_DATA_BEHAVIOR.
Note: In case of overrun set to data preserved and usage with programming model with interruption (HAL_Start_IT()): ADC IRQ handler has to clear
end of conversion flags, this induces the release of the preserved data. If needed, this data can be saved in function
HAL_ADC_ConvCpltCallback(), placed in user program code (called before end of conversion flags clear).
Note: Error reporting with respect to the conversion mode:
- Usage with ADC conversion by polling for event or interruption: Error is reported only if overrun is set to data preserved. If overrun is set to data
overwritten, user can willingly not read all the converted data, this is not considered as an erroneous case.
- Usage with ADC conversion by DMA: Error is reported whatever overrun setting (DMA is expected to process all data from data register). */
uint32_t LeftBitShift; /*!< Configures the left shifting applied to the final result with or without oversampling.
This parameter can be a value of @ref ADCEx_Left_Bit_Shift */
FunctionalState OversamplingMode; /*!< Specify whether the oversampling feature is enabled or disabled.
This parameter can be set to ENABLE or DISABLE.
Note: This parameter can be modified only if there is no conversion is ongoing on ADC groups regular and injected */
ADC_OversamplingTypeDef Oversampling; /*!< Specify the Oversampling parameters.
Caution: this setting overwrites the previous oversampling configuration if oversampling is already enabled. */
} ADC_InitTypeDef;
/**
* @brief Structure definition of ADC channel for regular group
* @note The setting of these parameters by function HAL_ADC_ConfigChannel() is conditioned to ADC state.
* ADC state can be either:
* - For all parameters: ADC disabled (this is the only possible ADC state to modify parameter 'SingleDiff')
* - For all except parameters 'SamplingTime', 'Offset', 'OffsetNumber': ADC enabled without conversion on going on regular group.
* - For parameters 'SamplingTime', 'Offset', 'OffsetNumber': ADC enabled without conversion on going on regular and injected groups.
* If ADC is not in the appropriate state to modify some parameters, these parameters setting is bypassed
* without error reporting (as it can be the expected behavior in case of intended action to update another parameter (which fulfills the ADC state condition)
* on the fly).
*/
typedef struct
{
uint32_t Channel; /*!< Specify the channel to configure into ADC regular group.
This parameter can be a value of @ref ADC_HAL_EC_CHANNEL
Note: Depending on devices and ADC instances, some channels may not be available on device package pins. Refer to device datasheet for channels availability. */
uint32_t Rank; /*!< Specify the rank in the regular group sequencer.
This parameter can be a value of @ref ADC_HAL_EC_REG_SEQ_RANKS
Note: to disable a channel or change order of conversion sequencer, rank containing a previous channel setting can be overwritten by
the new channel setting (or parameter number of conversions adjusted) */
uint32_t SamplingTime; /*!< Sampling time value to be set for the selected channel.
Unit: ADC clock cycles
Conversion time is the addition of sampling time and processing time
(12.5 ADC clock cycles at ADC resolution 12 bits, 10.5 cycles at 10 bits, 8.5 cycles at 8 bits, 6.5 cycles at 6 bits).
This parameter can be a value of @ref ADC_HAL_EC_CHANNEL_SAMPLINGTIME
Caution: This parameter applies to a channel that can be used into regular and/or injected group.
It overwrites the last setting.
Note: In case of usage of internal measurement channels (VrefInt/Vbat/TempSensor),
sampling time constraints must be respected (sampling time can be adjusted in function of ADC clock frequency and sampling time setting)
Refer to device datasheet for timings values. */
uint32_t SingleDiff; /*!< Select single-ended or differential input.
In differential mode: Differential measurement is carried out between the selected channel 'i' (positive input) and channel 'i+1' (negative input).
Only channel 'i' has to be configured, channel 'i+1' is configured automatically.
This parameter must be a value of @ref ADC_HAL_EC_CHANNEL_SINGLE_DIFF_ENDING
Caution: This parameter applies to a channel that can be used in a regular and/or injected group.
It overwrites the last setting.
Note: Refer to Reference Manual to ensure the selected channel is available in differential mode.
Note: When configuring a channel 'i' in differential mode, the channel 'i+1' is not usable separately.
Note: This parameter must be modified when ADC is disabled (before ADC start conversion or after ADC stop conversion).
If ADC is enabled, this parameter setting is bypassed without error reporting (as it can be the expected behavior in case
of another parameter update on the fly) */
uint32_t OffsetNumber; /*!< Select the offset number
This parameter can be a value of @ref ADC_HAL_EC_OFFSET_NB
Caution: Only one offset is allowed per channel. This parameter overwrites the last setting. */
uint32_t Offset; /*!< Define the offset to be subtracted from the raw converted data.
Offset value must be a positive number.
Depending of ADC resolution selected (16, 14, 12, 10, 8 bits), this parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF,
0x3FFF, 0xFFF, 0x3FF or 0xFF respectively.
Note: This parameter must be modified when no conversion is on going on both regular and injected groups (ADC disabled, or ADC enabled
without continuous mode or external trigger that could launch a conversion). */
FunctionalState OffsetRightShift; /*!< Define the Right-shift data after Offset correction.
This parameter is applied only for 16-bit or 8-bit resolution.
This parameter can be set to ENABLE or DISABLE.*/
FunctionalState OffsetSignedSaturation; /*!< Specify whether the Signed saturation feature is used or not.
This parameter is applied only for 16-bit or 8-bit resolution.
This parameter can be set to ENABLE or DISABLE. */
} ADC_ChannelConfTypeDef;
/**
* @brief Structure definition of ADC analog watchdog
* @note The setting of these parameters by function HAL_ADC_AnalogWDGConfig() is conditioned to ADC state.
* ADC state can be either:
* - For all parameters: ADC disabled or ADC enabled without conversion on going on ADC groups regular and injected.
*/
typedef struct
{
uint32_t WatchdogNumber; /*!< Select which ADC analog watchdog is monitoring the selected channel.
For Analog Watchdog 1: Only 1 channel can be monitored (or overall group of channels by setting parameter 'WatchdogMode')
For Analog Watchdog 2 and 3: Several channels can be monitored (by successive calls of 'HAL_ADC_AnalogWDGConfig()' for each channel)
This parameter can be a value of @ref ADC_HAL_EC_AWD_NUMBER. */
uint32_t WatchdogMode; /*!< Configure the ADC analog watchdog mode: single/all/none channels.
For Analog Watchdog 1: Configure the ADC analog watchdog mode: single channel or all channels, ADC groups regular and-or injected.
For Analog Watchdog 2 and 3: Several channels can be monitored by applying successively the AWD init structure. Channels on ADC group regular and injected are not differentiated: Set value 'ADC_ANALOGWATCHDOG_SINGLE_xxx' to monitor 1 channel, value 'ADC_ANALOGWATCHDOG_ALL_xxx' to monitor all channels, 'ADC_ANALOGWATCHDOG_NONE' to monitor no channel.
This parameter can be a value of @ref ADC_analog_watchdog_mode. */
uint32_t Channel; /*!< Select which ADC channel to monitor by analog watchdog.
For Analog Watchdog 1: this parameter has an effect only if parameter 'WatchdogMode' is configured on single channel (only 1 channel can be monitored).
For Analog Watchdog 2 and 3: Several channels can be monitored. To use this feature, call successively the function HAL_ADC_AnalogWDGConfig() for each channel to be added (or removed with value 'ADC_ANALOGWATCHDOG_NONE').
This parameter can be a value of @ref ADC_HAL_EC_CHANNEL. */
FunctionalState ITMode; /*!< Specify whether the analog watchdog is configured in interrupt or polling mode.
This parameter can be set to ENABLE or DISABLE */
uint32_t HighThreshold; /*!< Configure the ADC analog watchdog High threshold value.
Depending of ADC resolution selected (16, 14, 12, 10, 8 bits), this parameter must be a number
between Min_Data = 0x000 and Max_Data = 0xFFFF, 0x3FFF, 0xFFF, 0x3FF or 0xFF respectively.
Note: Analog watchdog 2 and 3 are limited to a resolution of 8 bits: if ADC resolution is 12 bits
the 4 LSB are ignored, if ADC resolution is 10 bits the 2 LSB are ignored.
Note: If ADC oversampling is enabled, ADC analog watchdog thresholds are
impacted: the comparison of analog watchdog thresholds is done
on oversampling intermediate computation (after ratio, before shift
application): intermediate register bitfield [32:7] (26 most significant bits). */
uint32_t LowThreshold; /*!< Configures the ADC analog watchdog Low threshold value.
Depending of ADC resolution selected (16, 14, 12, 10, 8 bits), this parameter must be a number
between Min_Data = 0x000 and Max_Data = 0xFFFF, 0x3FFF, 0xFFF, 0x3FF or 0xFF respectively.
Note: Analog watchdog 2 and 3 are limited to a resolution of 8 bits: if ADC resolution is 12 bits
the 4 LSB are ignored, if ADC resolution is 10 bits the 2 LSB are ignored.
Note: If ADC oversampling is enabled, ADC analog watchdog thresholds are
impacted: the comparison of analog watchdog thresholds is done
on oversampling intermediate computation (after ratio, before shift
application): intermediate register bitfield [32:7] (26 most significant bits). */
} ADC_AnalogWDGConfTypeDef;
/**
* @brief ADC group injected contexts queue configuration
* @note Structure intended to be used only through structure "ADC_HandleTypeDef"
*/
typedef struct
{
uint32_t ContextQueue; /*!< Injected channel configuration context: build-up over each
HAL_ADCEx_InjectedConfigChannel() call to finally initialize
JSQR register at HAL_ADCEx_InjectedConfigChannel() last call */
uint32_t ChannelCount; /*!< Number of channels in the injected sequence */
} ADC_InjectionConfigTypeDef;
/** @defgroup ADC_States ADC States
* @{
*/
/**
* @brief HAL ADC state machine: ADC states definition (bitfields)
* @note ADC state machine is managed by bitfields, state must be compared
* with bit by bit.
* For example:
* " if ((HAL_ADC_GetState(hadc1) & HAL_ADC_STATE_REG_BUSY) != 0UL) "
* " if ((HAL_ADC_GetState(hadc1) & HAL_ADC_STATE_AWD1) != 0UL) "
*/
/* States of ADC global scope */
#define HAL_ADC_STATE_RESET (0x00000000UL) /*!< ADC not yet initialized or disabled */
#define HAL_ADC_STATE_READY (0x00000001UL) /*!< ADC peripheral ready for use */
#define HAL_ADC_STATE_BUSY_INTERNAL (0x00000002UL) /*!< ADC is busy due to an internal process (initialization, calibration) */
#define HAL_ADC_STATE_TIMEOUT (0x00000004UL) /*!< TimeOut occurrence */
/* States of ADC errors */
#define HAL_ADC_STATE_ERROR_INTERNAL (0x00000010UL) /*!< Internal error occurrence */
#define HAL_ADC_STATE_ERROR_CONFIG (0x00000020UL) /*!< Configuration error occurrence */
#define HAL_ADC_STATE_ERROR_DMA (0x00000040UL) /*!< DMA error occurrence */
/* States of ADC group regular */
#define HAL_ADC_STATE_REG_BUSY (0x00000100UL) /*!< A conversion on ADC group regular is ongoing or can occur (either by continuous mode,
external trigger, low power auto power-on (if feature available), multimode ADC master control (if feature available)) */
#define HAL_ADC_STATE_REG_EOC (0x00000200UL) /*!< Conversion data available on group regular */
#define HAL_ADC_STATE_REG_OVR (0x00000400UL) /*!< Overrun occurrence */
#define HAL_ADC_STATE_REG_EOSMP (0x00000800UL) /*!< Not available on this STM32 serie: End Of Sampling flag raised */
/* States of ADC group injected */
#define HAL_ADC_STATE_INJ_BUSY (0x00001000UL) /*!< A conversion on ADC group injected is ongoing or can occur (either by auto-injection mode,
external trigger, low power auto power-on (if feature available), multimode ADC master control (if feature available)) */
#define HAL_ADC_STATE_INJ_EOC (0x00002000UL) /*!< Conversion data available on group injected */
#define HAL_ADC_STATE_INJ_JQOVF (0x00004000UL) /*!< Injected queue overflow occurrence */
/* States of ADC analog watchdogs */
#define HAL_ADC_STATE_AWD1 (0x00010000UL) /*!< Out-of-window occurrence of ADC analog watchdog 1 */
#define HAL_ADC_STATE_AWD2 (0x00020000UL) /*!< Out-of-window occurrence of ADC analog watchdog 2 */
#define HAL_ADC_STATE_AWD3 (0x00040000UL) /*!< Out-of-window occurrence of ADC analog watchdog 3 */
/* States of ADC multi-mode */
#define HAL_ADC_STATE_MULTIMODE_SLAVE (0x00100000UL) /*!< ADC in multimode slave state, controlled by another ADC master (when feature available) */
/**
* @}
*/
/**
* @brief ADC handle Structure definition
*/
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
typedef struct __ADC_HandleTypeDef
#else
typedef struct
#endif
{
ADC_TypeDef *Instance; /*!< Register base address */
ADC_InitTypeDef Init; /*!< ADC initialization parameters and regular conversions setting */
DMA_HandleTypeDef *DMA_Handle; /*!< Pointer DMA Handler */
HAL_LockTypeDef Lock; /*!< ADC locking object */
__IO uint32_t State; /*!< ADC communication state (bitmap of ADC states) */
__IO uint32_t ErrorCode; /*!< ADC Error code */
ADC_InjectionConfigTypeDef InjectionConfig ; /*!< ADC injected channel configuration build-up structure */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
void (* ConvCpltCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC conversion complete callback */
void (* ConvHalfCpltCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC conversion DMA half-transfer callback */
void (* LevelOutOfWindowCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC analog watchdog 1 callback */
void (* ErrorCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC error callback */
void (* InjectedConvCpltCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC group injected conversion complete callback */
void (* InjectedQueueOverflowCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC group injected context queue overflow callback */
void (* LevelOutOfWindow2Callback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC analog watchdog 2 callback */
void (* LevelOutOfWindow3Callback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC analog watchdog 3 callback */
void (* EndOfSamplingCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC end of sampling callback */
void (* MspInitCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC Msp Init callback */
void (* MspDeInitCallback)(struct __ADC_HandleTypeDef *hadc); /*!< ADC Msp DeInit callback */
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
} ADC_HandleTypeDef;
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
/**
* @brief HAL ADC Callback ID enumeration definition
*/
typedef enum
{
HAL_ADC_CONVERSION_COMPLETE_CB_ID = 0x00U, /*!< ADC conversion complete callback ID */
HAL_ADC_CONVERSION_HALF_CB_ID = 0x01U, /*!< ADC conversion DMA half-transfer callback ID */
HAL_ADC_LEVEL_OUT_OF_WINDOW_1_CB_ID = 0x02U, /*!< ADC analog watchdog 1 callback ID */
HAL_ADC_ERROR_CB_ID = 0x03U, /*!< ADC error callback ID */
HAL_ADC_INJ_CONVERSION_COMPLETE_CB_ID = 0x04U, /*!< ADC group injected conversion complete callback ID */
HAL_ADC_INJ_QUEUE_OVEFLOW_CB_ID = 0x05U, /*!< ADC group injected context queue overflow callback ID */
HAL_ADC_LEVEL_OUT_OF_WINDOW_2_CB_ID = 0x06U, /*!< ADC analog watchdog 2 callback ID */
HAL_ADC_LEVEL_OUT_OF_WINDOW_3_CB_ID = 0x07U, /*!< ADC analog watchdog 3 callback ID */
HAL_ADC_END_OF_SAMPLING_CB_ID = 0x08U, /*!< ADC end of sampling callback ID */
HAL_ADC_MSPINIT_CB_ID = 0x09U, /*!< ADC Msp Init callback ID */
HAL_ADC_MSPDEINIT_CB_ID = 0x0AU /*!< ADC Msp DeInit callback ID */
} HAL_ADC_CallbackIDTypeDef;
/**
* @brief HAL ADC Callback pointer definition
*/
typedef void (*pADC_CallbackTypeDef)(ADC_HandleTypeDef *hadc); /*!< pointer to a ADC callback function */
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup ADC_Exported_Constants ADC Exported Constants
* @{
*/
/** @defgroup ADC_Error_Code ADC Error Code
* @{
*/
#define HAL_ADC_ERROR_NONE (0x00U) /*!< No error */
#define HAL_ADC_ERROR_INTERNAL (0x01U) /*!< ADC peripheral internal error (problem of clocking,
enable/disable, erroneous state, ...) */
#define HAL_ADC_ERROR_OVR (0x02U) /*!< Overrun error */
#define HAL_ADC_ERROR_DMA (0x04U) /*!< DMA transfer error */
#define HAL_ADC_ERROR_JQOVF (0x08U) /*!< Injected context queue overflow error */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
#define HAL_ADC_ERROR_INVALID_CALLBACK (0x10U) /*!< Invalid Callback error */
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_COMMON_CLOCK_SOURCE ADC common - Clock source
* @{
*/
#define ADC_CLOCK_SYNC_PCLK_DIV1 (LL_ADC_CLOCK_SYNC_PCLK_DIV1) /*!< ADC synchronous clock derived from AHB clock without prescaler */
#define ADC_CLOCK_SYNC_PCLK_DIV2 (LL_ADC_CLOCK_SYNC_PCLK_DIV2) /*!< ADC synchronous clock derived from AHB clock with prescaler division by 2 */
#define ADC_CLOCK_SYNC_PCLK_DIV4 (LL_ADC_CLOCK_SYNC_PCLK_DIV4) /*!< ADC synchronous clock derived from AHB clock with prescaler division by 4 */
#define ADC_CLOCK_ASYNC_DIV1 (LL_ADC_CLOCK_ASYNC_DIV1) /*!< ADC asynchronous clock without prescaler */
#define ADC_CLOCK_ASYNC_DIV2 (LL_ADC_CLOCK_ASYNC_DIV2) /*!< ADC asynchronous clock with prescaler division by 2 */
#define ADC_CLOCK_ASYNC_DIV4 (LL_ADC_CLOCK_ASYNC_DIV4) /*!< ADC asynchronous clock with prescaler division by 4 */
#define ADC_CLOCK_ASYNC_DIV6 (LL_ADC_CLOCK_ASYNC_DIV6) /*!< ADC asynchronous clock with prescaler division by 6 */
#define ADC_CLOCK_ASYNC_DIV8 (LL_ADC_CLOCK_ASYNC_DIV8) /*!< ADC asynchronous clock with prescaler division by 8 */
#define ADC_CLOCK_ASYNC_DIV10 (LL_ADC_CLOCK_ASYNC_DIV10) /*!< ADC asynchronous clock with prescaler division by 10 */
#define ADC_CLOCK_ASYNC_DIV12 (LL_ADC_CLOCK_ASYNC_DIV12) /*!< ADC asynchronous clock with prescaler division by 12 */
#define ADC_CLOCK_ASYNC_DIV16 (LL_ADC_CLOCK_ASYNC_DIV16) /*!< ADC asynchronous clock with prescaler division by 16 */
#define ADC_CLOCK_ASYNC_DIV32 (LL_ADC_CLOCK_ASYNC_DIV32) /*!< ADC asynchronous clock with prescaler division by 32 */
#define ADC_CLOCK_ASYNC_DIV64 (LL_ADC_CLOCK_ASYNC_DIV64) /*!< ADC asynchronous clock with prescaler division by 64 */
#define ADC_CLOCK_ASYNC_DIV128 (LL_ADC_CLOCK_ASYNC_DIV128) /*!< ADC asynchronous clock with prescaler division by 128 */
#define ADC_CLOCK_ASYNC_DIV256 (LL_ADC_CLOCK_ASYNC_DIV256) /*!< ADC asynchronous clock with prescaler division by 256 */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_RESOLUTION ADC instance - Resolution
* @{
*/
#define ADC_RESOLUTION_16B (LL_ADC_RESOLUTION_16B) /*!< ADC resolution 16 bits */
#define ADC_RESOLUTION_14B (LL_ADC_RESOLUTION_14B) /*!< ADC resolution 14 bits */
#define ADC_RESOLUTION_12B (LL_ADC_RESOLUTION_12B) /*!< ADC resolution 12 bits */
#define ADC_RESOLUTION_10B (LL_ADC_RESOLUTION_10B) /*!< ADC resolution 10 bits */
#define ADC_RESOLUTION_8B (LL_ADC_RESOLUTION_8B) /*!< ADC resolution 8 bits */
/**
* @}
*/
/** @defgroup ADC_Scan_mode ADC sequencer scan mode
* @{
*/
#define ADC_SCAN_DISABLE (0x00000000UL) /*!< Scan mode disabled */
#define ADC_SCAN_ENABLE (0x00000001UL) /*!< Scan mode enabled */
/**
* @}
*/
/** @defgroup ADC_regular_external_trigger_source ADC group regular trigger source
* @{
*/
/* ADC group regular trigger sources for all ADC instances */
#define ADC_SOFTWARE_START (LL_ADC_REG_TRIG_SOFTWARE) /*!< ADC group regular conversion trigger internal: SW start. */
#define ADC_EXTERNALTRIG_T1_CC1 (LL_ADC_REG_TRIG_EXT_TIM1_CH1) /*!< ADC group regular conversion trigger from external peripheral: TIM1 channel 1 event (capture compare: input capture or output capture). Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T1_CC2 (LL_ADC_REG_TRIG_EXT_TIM1_CH2) /*!< ADC group regular conversion trigger from external peripheral: TIM1 channel 2 event (capture compare: input capture or output capture). Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T1_CC3 (LL_ADC_REG_TRIG_EXT_TIM1_CH3) /*!< ADC group regular conversion trigger from external peripheral: TIM1 channel 3 event (capture compare: input capture or output capture). Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T2_CC2 (LL_ADC_REG_TRIG_EXT_TIM2_CH2) /*!< ADC group regular conversion trigger from external peripheral: TIM2 channel 2 event (capture compare: input capture or output capture). Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T3_TRGO (LL_ADC_REG_TRIG_EXT_TIM3_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM3 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T4_CC4 (LL_ADC_REG_TRIG_EXT_TIM4_CH4) /*!< ADC group regular conversion trigger from external peripheral: TIM4 channel 4 event (capture compare: input capture or output capture). Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_EXT_IT11 (LL_ADC_REG_TRIG_EXT_EXTI_LINE11) /*!< ADC group regular conversion trigger from external peripheral: external interrupt line 11 event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T8_TRGO (LL_ADC_REG_TRIG_EXT_TIM8_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM8 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T8_TRGO2 (LL_ADC_REG_TRIG_EXT_TIM8_TRGO2) /*!< ADC group regular conversion trigger from external peripheral: TIM8 TRGO2 event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T1_TRGO (LL_ADC_REG_TRIG_EXT_TIM1_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM1 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T1_TRGO2 (LL_ADC_REG_TRIG_EXT_TIM1_TRGO2) /*!< ADC group regular conversion trigger from external peripheral: TIM1 TRGO2 event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T2_TRGO (LL_ADC_REG_TRIG_EXT_TIM2_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM2 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T4_TRGO (LL_ADC_REG_TRIG_EXT_TIM4_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM4 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T6_TRGO (LL_ADC_REG_TRIG_EXT_TIM6_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM6 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T15_TRGO (LL_ADC_REG_TRIG_EXT_TIM15_TRGO) /*!< ADC group regular conversion trigger from external peripheral: TIM15 TRGO event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_T3_CC4 (LL_ADC_REG_TRIG_EXT_TIM3_CH4) /*!< ADC group regular conversion trigger from external peripheral: TIM3 channel 4 event (capture compare: input capture or output capture). Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_HR1_ADCTRG1 (LL_ADC_REG_TRIG_EXT_HRTIM_TRG1) /*!< ADC group regular conversion trigger from external peripheral: HRTIM TRG1 event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_HR1_ADCTRG3 (LL_ADC_REG_TRIG_EXT_HRTIM_TRG3) /*!< ADC group regular conversion trigger from external peripheral: HRTIM TRG3 event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_LPTIM1_OUT (LL_ADC_REG_TRIG_EXT_LPTIM1_OUT) /*!< ADC group regular conversion trigger from external peripheral: LPTIM1 OUT event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_LPTIM2_OUT (LL_ADC_REG_TRIG_EXT_LPTIM2_OUT) /*!< ADC group regular conversion trigger from external peripheral: LPTIM2 OUT event. Trigger edge set to rising edge (default setting). */
#define ADC_EXTERNALTRIG_LPTIM3_OUT (LL_ADC_REG_TRIG_EXT_LPTIM3_OUT) /*!< ADC group regular conversion trigger from external peripheral: LPTIM3 event OUT. Trigger edge set to rising edge (default setting). */
/**
* @}
*/
/** @defgroup ADC_regular_external_trigger_edge ADC group regular trigger edge (when external trigger is selected)
* @{
*/
#define ADC_EXTERNALTRIGCONVEDGE_NONE (0x00000000UL) /*!< Regular conversions hardware trigger detection disabled */
#define ADC_EXTERNALTRIGCONVEDGE_RISING (LL_ADC_REG_TRIG_EXT_RISING) /*!< ADC group regular conversion trigger polarity set to rising edge */
#define ADC_EXTERNALTRIGCONVEDGE_FALLING (LL_ADC_REG_TRIG_EXT_FALLING) /*!< ADC group regular conversion trigger polarity set to falling edge */
#define ADC_EXTERNALTRIGCONVEDGE_RISINGFALLING (LL_ADC_REG_TRIG_EXT_RISINGFALLING) /*!< ADC group regular conversion trigger polarity set to both rising and falling edges */
/**
* @}
*/
/** @defgroup ADC_EOCSelection ADC sequencer end of unitary conversion or sequence conversions
* @{
*/
#define ADC_EOC_SINGLE_CONV (ADC_ISR_EOC) /*!< End of unitary conversion flag */
#define ADC_EOC_SEQ_CONV (ADC_ISR_EOS) /*!< End of sequence conversions flag */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_REG_OVR_DATA_BEHAVIOR ADC group regular - Overrun behavior on conversion data
* @{
*/
#define ADC_OVR_DATA_PRESERVED (LL_ADC_REG_OVR_DATA_PRESERVED) /*!< ADC group regular behavior in case of overrun: data preserved */
#define ADC_OVR_DATA_OVERWRITTEN (LL_ADC_REG_OVR_DATA_OVERWRITTEN) /*!< ADC group regular behavior in case of overrun: data overwritten */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_REG_SEQ_RANKS ADC group regular - Sequencer ranks
* @{
*/
#define ADC_REGULAR_RANK_1 (LL_ADC_REG_RANK_1) /*!< ADC group regular sequencer rank 1 */
#define ADC_REGULAR_RANK_2 (LL_ADC_REG_RANK_2) /*!< ADC group regular sequencer rank 2 */
#define ADC_REGULAR_RANK_3 (LL_ADC_REG_RANK_3) /*!< ADC group regular sequencer rank 3 */
#define ADC_REGULAR_RANK_4 (LL_ADC_REG_RANK_4) /*!< ADC group regular sequencer rank 4 */
#define ADC_REGULAR_RANK_5 (LL_ADC_REG_RANK_5) /*!< ADC group regular sequencer rank 5 */
#define ADC_REGULAR_RANK_6 (LL_ADC_REG_RANK_6) /*!< ADC group regular sequencer rank 6 */
#define ADC_REGULAR_RANK_7 (LL_ADC_REG_RANK_7) /*!< ADC group regular sequencer rank 7 */
#define ADC_REGULAR_RANK_8 (LL_ADC_REG_RANK_8) /*!< ADC group regular sequencer rank 8 */
#define ADC_REGULAR_RANK_9 (LL_ADC_REG_RANK_9) /*!< ADC group regular sequencer rank 9 */
#define ADC_REGULAR_RANK_10 (LL_ADC_REG_RANK_10) /*!< ADC group regular sequencer rank 10 */
#define ADC_REGULAR_RANK_11 (LL_ADC_REG_RANK_11) /*!< ADC group regular sequencer rank 11 */
#define ADC_REGULAR_RANK_12 (LL_ADC_REG_RANK_12) /*!< ADC group regular sequencer rank 12 */
#define ADC_REGULAR_RANK_13 (LL_ADC_REG_RANK_13) /*!< ADC group regular sequencer rank 13 */
#define ADC_REGULAR_RANK_14 (LL_ADC_REG_RANK_14) /*!< ADC group regular sequencer rank 14 */
#define ADC_REGULAR_RANK_15 (LL_ADC_REG_RANK_15) /*!< ADC group regular sequencer rank 15 */
#define ADC_REGULAR_RANK_16 (LL_ADC_REG_RANK_16) /*!< ADC group regular sequencer rank 16 */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_CHANNEL_SAMPLINGTIME Channel - Sampling time
* @{
*/
#define ADC_SAMPLETIME_1CYCLE_5 (LL_ADC_SAMPLINGTIME_1CYCLE_5) /*!< Sampling time 1.5 ADC clock cycles */
#define ADC_SAMPLETIME_2CYCLES_5 (LL_ADC_SAMPLINGTIME_2CYCLES_5) /*!< Sampling time 2.5 ADC clock cycles */
#define ADC_SAMPLETIME_8CYCLES_5 (LL_ADC_SAMPLINGTIME_8CYCLES_5) /*!< Sampling time 8.5 ADC clock cycles */
#define ADC_SAMPLETIME_16CYCLES_5 (LL_ADC_SAMPLINGTIME_16CYCLES_5) /*!< Sampling time 16.5 ADC clock cycles */
#define ADC_SAMPLETIME_32CYCLES_5 (LL_ADC_SAMPLINGTIME_32CYCLES_5) /*!< Sampling time 32.5 ADC clock cycles */
#define ADC_SAMPLETIME_64CYCLES_5 (LL_ADC_SAMPLINGTIME_64CYCLES_5) /*!< Sampling time 64.5 ADC clock cycles */
#define ADC_SAMPLETIME_387CYCLES_5 (LL_ADC_SAMPLINGTIME_387CYCLES_5) /*!< Sampling time 387.5 ADC clock cycles */
#define ADC_SAMPLETIME_810CYCLES_5 (LL_ADC_SAMPLINGTIME_810CYCLES_5) /*!< Sampling time 810.5 ADC clock cycles */
/**
* @}
*/
/** @defgroup ADCEx_Calibration_Mode ADC Extended Calibration mode offset mode or linear mode
* @{
*/
#define ADC_CALIB_OFFSET (LL_ADC_CALIB_OFFSET)
#define ADC_CALIB_OFFSET_LINEARITY (LL_ADC_CALIB_OFFSET_LINEARITY)
/**
* @}
*/
/** @defgroup ADC_HAL_EC_CHANNEL ADC instance - Channel number
* @{
*/
/* Note: VrefInt, TempSensor and Vbat internal channels are not available on */
/* all ADC instances (refer to Reference Manual). */
#define ADC_CHANNEL_0 (LL_ADC_CHANNEL_0) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN0 */
#define ADC_CHANNEL_1 (LL_ADC_CHANNEL_1) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN1 */
#define ADC_CHANNEL_2 (LL_ADC_CHANNEL_2) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN2 */
#define ADC_CHANNEL_3 (LL_ADC_CHANNEL_3) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN3 */
#define ADC_CHANNEL_4 (LL_ADC_CHANNEL_4) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN4 */
#define ADC_CHANNEL_5 (LL_ADC_CHANNEL_5) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN5 */
#define ADC_CHANNEL_6 (LL_ADC_CHANNEL_6) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN6 */
#define ADC_CHANNEL_7 (LL_ADC_CHANNEL_7) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN7 */
#define ADC_CHANNEL_8 (LL_ADC_CHANNEL_8) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN8 */
#define ADC_CHANNEL_9 (LL_ADC_CHANNEL_9) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN9 */
#define ADC_CHANNEL_10 (LL_ADC_CHANNEL_10) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN10 */
#define ADC_CHANNEL_11 (LL_ADC_CHANNEL_11) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN11 */
#define ADC_CHANNEL_12 (LL_ADC_CHANNEL_12) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN12 */
#define ADC_CHANNEL_13 (LL_ADC_CHANNEL_13) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN13 */
#define ADC_CHANNEL_14 (LL_ADC_CHANNEL_14) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN14 */
#define ADC_CHANNEL_15 (LL_ADC_CHANNEL_15) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN15 */
#define ADC_CHANNEL_16 (LL_ADC_CHANNEL_16) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN16 */
#define ADC_CHANNEL_17 (LL_ADC_CHANNEL_17) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN17 */
#define ADC_CHANNEL_18 (LL_ADC_CHANNEL_18) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN18 */
#define ADC_CHANNEL_19 (LL_ADC_CHANNEL_19) /*!< ADC external channel (channel connected to GPIO pin) ADCx_IN19 */
#define ADC_CHANNEL_VREFINT (LL_ADC_CHANNEL_VREFINT) /*!< ADC internal channel connected to VrefInt: Internal voltage reference, channel specific to ADC3. */
#define ADC_CHANNEL_TEMPSENSOR (LL_ADC_CHANNEL_TEMPSENSOR) /*!< ADC internal channel connected to Temperature sensor, channel specific to ADC3. */
#define ADC_CHANNEL_VBAT (LL_ADC_CHANNEL_VBAT) /*!< ADC internal channel connected to Vbat/4: Vbat voltage through a divider ladder of factor 1/4 to have Vbat always below Vdda, channel specific to ADC3. */
#define ADC_CHANNEL_DAC1CH1_ADC2 (LL_ADC_CHANNEL_DAC1CH1_ADC2) /*!< ADC internal channel connected to DAC1 channel 1, channel specific to ADC2 */
#define ADC_CHANNEL_DAC1CH2_ADC2 (LL_ADC_CHANNEL_DAC1CH2_ADC2) /*!< ADC internal channel connected to DAC1 channel 2, channel specific to ADC2 */
/**
* @}
*/
/** @defgroup ADC_ConversionDataManagement ADC Conversion Data Management
* @{
*/
#define ADC_CONVERSIONDATA_DR ((uint32_t)0x00000000) /*!< Regular Conversion data stored in DR register only */
#define ADC_CONVERSIONDATA_DFSDM ((uint32_t)ADC_CFGR_DMNGT_1) /*!< DFSDM mode selected */
#define ADC_CONVERSIONDATA_DMA_ONESHOT ((uint32_t)ADC_CFGR_DMNGT_0) /*!< DMA one shot mode selected */
#define ADC_CONVERSIONDATA_DMA_CIRCULAR ((uint32_t)(ADC_CFGR_DMNGT_0 | ADC_CFGR_DMNGT_1)) /*!< DMA circular mode selected */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_AWD_NUMBER Analog watchdog - Analog watchdog number
* @{
*/
#define ADC_ANALOGWATCHDOG_1 (LL_ADC_AWD1) /*!< ADC analog watchdog number 1 */
#define ADC_ANALOGWATCHDOG_2 (LL_ADC_AWD2) /*!< ADC analog watchdog number 2 */
#define ADC_ANALOGWATCHDOG_3 (LL_ADC_AWD3) /*!< ADC analog watchdog number 3 */
/**
* @}
*/
/** @defgroup ADC_analog_watchdog_mode ADC Analog Watchdog Mode
* @{
*/
#define ADC_ANALOGWATCHDOG_NONE (0x00000000UL) /*!< No analog watchdog selected */
#define ADC_ANALOGWATCHDOG_SINGLE_REG (ADC_CFGR_AWD1SGL | ADC_CFGR_AWD1EN) /*!< Analog watchdog applied to a regular group single channel */
#define ADC_ANALOGWATCHDOG_SINGLE_INJEC (ADC_CFGR_AWD1SGL | ADC_CFGR_JAWD1EN) /*!< Analog watchdog applied to an injected group single channel */
#define ADC_ANALOGWATCHDOG_SINGLE_REGINJEC (ADC_CFGR_AWD1SGL | ADC_CFGR_AWD1EN | ADC_CFGR_JAWD1EN) /*!< Analog watchdog applied to a regular and injected groups single channel */
#define ADC_ANALOGWATCHDOG_ALL_REG (ADC_CFGR_AWD1EN) /*!< Analog watchdog applied to regular group all channels */
#define ADC_ANALOGWATCHDOG_ALL_INJEC (ADC_CFGR_JAWD1EN) /*!< Analog watchdog applied to injected group all channels */
#define ADC_ANALOGWATCHDOG_ALL_REGINJEC (ADC_CFGR_AWD1EN | ADC_CFGR_JAWD1EN) /*!< Analog watchdog applied to regular and injected groups all channels */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_OVS_SHIFT Oversampling - Data shift
* @{
*/
#define ADC_RIGHTBITSHIFT_NONE (LL_ADC_OVS_SHIFT_NONE) /*!< ADC oversampling no shift (sum of the ADC conversions data is not divided to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_1 (LL_ADC_OVS_SHIFT_RIGHT_1) /*!< ADC oversampling shift of 1 (sum of the ADC conversions data is divided by 2 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_2 (LL_ADC_OVS_SHIFT_RIGHT_2) /*!< ADC oversampling shift of 2 (sum of the ADC conversions data is divided by 4 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_3 (LL_ADC_OVS_SHIFT_RIGHT_3) /*!< ADC oversampling shift of 3 (sum of the ADC conversions data is divided by 8 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_4 (LL_ADC_OVS_SHIFT_RIGHT_4) /*!< ADC oversampling shift of 4 (sum of the ADC conversions data is divided by 16 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_5 (LL_ADC_OVS_SHIFT_RIGHT_5) /*!< ADC oversampling shift of 5 (sum of the ADC conversions data is divided by 32 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_6 (LL_ADC_OVS_SHIFT_RIGHT_6) /*!< ADC oversampling shift of 6 (sum of the ADC conversions data is divided by 64 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_7 (LL_ADC_OVS_SHIFT_RIGHT_7) /*!< ADC oversampling shift of 7 (sum of the ADC conversions data is divided by 128 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_8 (LL_ADC_OVS_SHIFT_RIGHT_8) /*!< ADC oversampling shift of 8 (sum of the ADC conversions data is divided by 256 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_9 (LL_ADC_OVS_SHIFT_RIGHT_9) /*!< ADC oversampling shift of 9 (sum of the ADC conversions data is divided by 512 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_10 (LL_ADC_OVS_SHIFT_RIGHT_10)/*!< ADC oversampling shift of 10 (sum of the ADC conversions data is divided by 1024 to result as the ADC oversampling conversion data) */
#define ADC_RIGHTBITSHIFT_11 (LL_ADC_OVS_SHIFT_RIGHT_11)/*!< ADC oversampling shift of 11 (sum of the ADC conversions data is divided by 2048 to result as the ADC oversampling conversion data) */
/**
* @}
*/
/** @defgroup ADCEx_Left_Bit_Shift ADC Extended Oversampling left Shift
* @{
*/
#define ADC_LEFTBITSHIFT_NONE (LL_ADC_LEFT_BIT_SHIFT_NONE) /*!< ADC No bit shift */
#define ADC_LEFTBITSHIFT_1 (LL_ADC_LEFT_BIT_SHIFT_1) /*!< ADC 1 bit shift */
#define ADC_LEFTBITSHIFT_2 (LL_ADC_LEFT_BIT_SHIFT_2) /*!< ADC 2 bits shift */
#define ADC_LEFTBITSHIFT_3 (LL_ADC_LEFT_BIT_SHIFT_3) /*!< ADC 3 bits shift */
#define ADC_LEFTBITSHIFT_4 (LL_ADC_LEFT_BIT_SHIFT_4) /*!< ADC 4 bits shift */
#define ADC_LEFTBITSHIFT_5 (LL_ADC_LEFT_BIT_SHIFT_5) /*!< ADC 5 bits shift */
#define ADC_LEFTBITSHIFT_6 (LL_ADC_LEFT_BIT_SHIFT_6) /*!< ADC 6 bits shift */
#define ADC_LEFTBITSHIFT_7 (LL_ADC_LEFT_BIT_SHIFT_7) /*!< ADC 7 bits shift */
#define ADC_LEFTBITSHIFT_8 (LL_ADC_LEFT_BIT_SHIFT_8) /*!< ADC 8 bits shift */
#define ADC_LEFTBITSHIFT_9 (LL_ADC_LEFT_BIT_SHIFT_9) /*!< ADC 9 bits shift */
#define ADC_LEFTBITSHIFT_10 (LL_ADC_LEFT_BIT_SHIFT_10) /*!< ADC 10 bits shift */
#define ADC_LEFTBITSHIFT_11 (LL_ADC_LEFT_BIT_SHIFT_11) /*!< ADC 11 bits shift */
#define ADC_LEFTBITSHIFT_12 (LL_ADC_LEFT_BIT_SHIFT_12) /*!< ADC 12 bits shift */
#define ADC_LEFTBITSHIFT_13 (LL_ADC_LEFT_BIT_SHIFT_13) /*!< ADC 13 bits shift */
#define ADC_LEFTBITSHIFT_14 (LL_ADC_LEFT_BIT_SHIFT_14) /*!< ADC 14 bits shift */
#define ADC_LEFTBITSHIFT_15 (LL_ADC_LEFT_BIT_SHIFT_15) /*!< ADC 15 bits shift */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_OVS_DISCONT_MODE Oversampling - Discontinuous mode
* @{
*/
#define ADC_TRIGGEREDMODE_SINGLE_TRIGGER (LL_ADC_OVS_REG_CONT) /*!< ADC oversampling discontinuous mode: continuous mode (all conversions of oversampling ratio are done from 1 trigger) */
#define ADC_TRIGGEREDMODE_MULTI_TRIGGER (LL_ADC_OVS_REG_DISCONT) /*!< ADC oversampling discontinuous mode: discontinuous mode (each conversion of oversampling ratio needs a trigger) */
/**
* @}
*/
/** @defgroup ADC_HAL_EC_OVS_SCOPE_REG Oversampling - Oversampling scope for ADC group regular
* @{
*/
#define ADC_REGOVERSAMPLING_CONTINUED_MODE (LL_ADC_OVS_GRP_REGULAR_CONTINUED) /*!< Oversampling buffer maintained during injection sequence */
#define ADC_REGOVERSAMPLING_RESUMED_MODE (LL_ADC_OVS_GRP_REGULAR_RESUMED) /*!< Oversampling buffer zeroed during injection sequence */
/**
* @}
*/
/** @defgroup ADC_Event_type ADC Event type
* @{
*/
#define ADC_EOSMP_EVENT (ADC_FLAG_EOSMP) /*!< ADC End of Sampling event */
#define ADC_AWD1_EVENT (ADC_FLAG_AWD1) /*!< ADC Analog watchdog 1 event (main analog watchdog, present on all STM32 series) */
#define ADC_AWD2_EVENT (ADC_FLAG_AWD2) /*!< ADC Analog watchdog 2 event (additional analog watchdog, not present on all STM32 series) */
#define ADC_AWD3_EVENT (ADC_FLAG_AWD3) /*!< ADC Analog watchdog 3 event (additional analog watchdog, not present on all STM32 series) */
#define ADC_OVR_EVENT (ADC_FLAG_OVR) /*!< ADC overrun event */
#define ADC_JQOVF_EVENT (ADC_FLAG_JQOVF) /*!< ADC Injected Context Queue Overflow event */
/**
* @}
*/
#define ADC_AWD_EVENT ADC_AWD1_EVENT /*!< ADC Analog watchdog 1 event: Naming for compatibility with other STM32 devices having only one analog watchdog */
/** @defgroup ADC_interrupts_definition ADC interrupts definition
* @{
*/
#define ADC_IT_RDY ADC_IER_ADRDYIE /*!< ADC Ready interrupt source */
#define ADC_IT_EOSMP ADC_IER_EOSMPIE /*!< ADC End of sampling interrupt source */
#define ADC_IT_EOC ADC_IER_EOCIE /*!< ADC End of regular conversion interrupt source */
#define ADC_IT_EOS ADC_IER_EOSIE /*!< ADC End of regular sequence of conversions interrupt source */
#define ADC_IT_OVR ADC_IER_OVRIE /*!< ADC overrun interrupt source */
#define ADC_IT_JEOC ADC_IER_JEOCIE /*!< ADC End of injected conversion interrupt source */
#define ADC_IT_JEOS ADC_IER_JEOSIE /*!< ADC End of injected sequence of conversions interrupt source */
#define ADC_IT_AWD1 ADC_IER_AWD1IE /*!< ADC Analog watchdog 1 interrupt source (main analog watchdog) */
#define ADC_IT_AWD2 ADC_IER_AWD2IE /*!< ADC Analog watchdog 2 interrupt source (additional analog watchdog) */
#define ADC_IT_AWD3 ADC_IER_AWD3IE /*!< ADC Analog watchdog 3 interrupt source (additional analog watchdog) */
#define ADC_IT_JQOVF ADC_IER_JQOVFIE /*!< ADC Injected Context Queue Overflow interrupt source */
#define ADC_IT_AWD ADC_IT_AWD1 /*!< ADC Analog watchdog 1 interrupt source: naming for compatibility with other STM32 devices having only one analog watchdog */
/**
* @}
*/
/** @defgroup ADC_flags_definition ADC flags definition
* @{
*/
#define ADC_FLAG_RDY ADC_ISR_ADRDY /*!< ADC Ready flag */
#define ADC_FLAG_EOSMP ADC_ISR_EOSMP /*!< ADC End of Sampling flag */
#define ADC_FLAG_EOC ADC_ISR_EOC /*!< ADC End of Regular Conversion flag */
#define ADC_FLAG_EOS ADC_ISR_EOS /*!< ADC End of Regular sequence of Conversions flag */
#define ADC_FLAG_OVR ADC_ISR_OVR /*!< ADC overrun flag */
#define ADC_FLAG_JEOC ADC_ISR_JEOC /*!< ADC End of Injected Conversion flag */
#define ADC_FLAG_JEOS ADC_ISR_JEOS /*!< ADC End of Injected sequence of Conversions flag */
#define ADC_FLAG_AWD1 ADC_ISR_AWD1 /*!< ADC Analog watchdog 1 flag (main analog watchdog) */
#define ADC_FLAG_AWD2 ADC_ISR_AWD2 /*!< ADC Analog watchdog 2 flag (additional analog watchdog) */
#define ADC_FLAG_AWD3 ADC_ISR_AWD3 /*!< ADC Analog watchdog 3 flag (additional analog watchdog) */
#define ADC_FLAG_JQOVF ADC_ISR_JQOVF /*!< ADC Injected Context Queue Overflow flag */
/**
* @}
*/
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/** @defgroup ADC_Private_Macros ADC Private Macros
* @{
*/
/* Macro reserved for internal HAL driver usage, not intended to be used in */
/* code of final user. */
/**
* @brief Verify the ADC data conversion setting.
* @param DATA : programmed DATA conversion mode.
* @retval SET (DATA is a valid value) or RESET (DATA is invalid)
*/
#define IS_ADC_CONVERSIONDATAMGT(DATA) \
((((DATA) == ADC_CONVERSIONDATA_DR)) || \
(((DATA) == ADC_CONVERSIONDATA_DFSDM)) || \
(((DATA) == ADC_CONVERSIONDATA_DMA_ONESHOT)) || \
(((DATA) == ADC_CONVERSIONDATA_DMA_CIRCULAR)))
/**
* @brief Return resolution bits in CFGR register RES[1:0] field.
* @param __HANDLE__ ADC handle
* @retval Value of bitfield RES in CFGR register.
*/
#define ADC_GET_RESOLUTION(__HANDLE__) \
(LL_ADC_GetResolution((__HANDLE__)->Instance))
/**
* @brief Clear ADC error code (set it to no error code "HAL_ADC_ERROR_NONE").
* @param __HANDLE__ ADC handle
* @retval None
*/
#define ADC_CLEAR_ERRORCODE(__HANDLE__) ((__HANDLE__)->ErrorCode = HAL_ADC_ERROR_NONE)
/**
* @brief Verification of ADC state: enabled or disabled.
* @param __HANDLE__ ADC handle
* @retval SET (ADC enabled) or RESET (ADC disabled)
*/
#define ADC_IS_ENABLE(__HANDLE__) \
(( ((((__HANDLE__)->Instance->CR) & (ADC_CR_ADEN | ADC_CR_ADDIS)) == ADC_CR_ADEN) && \
((((__HANDLE__)->Instance->ISR) & ADC_FLAG_RDY) == ADC_FLAG_RDY) \
) ? SET : RESET)
/**
* @brief Check if conversion is on going on regular group.
* @param __HANDLE__ ADC handle
* @retval Value "0" (no conversion is on going) or value "1" (conversion is on going)
*/
#define ADC_IS_CONVERSION_ONGOING_REGULAR(__HANDLE__) \
(LL_ADC_REG_IsConversionOngoing((__HANDLE__)->Instance))
/**
* @brief Check if ADC clock mode is synchronous
* @param __HANDLE__: ADC handle
* @retval SET (clock mode is synchronous) or RESET (clock mode is asynchronous)
*/
#define ADC_IS_SYNCHRONOUS_CLOCK_MODE(__HANDLE__) \
(((((__HANDLE__)->Instance) == ADC1) || (((__HANDLE__)->Instance) == ADC2))? \
((ADC12_COMMON->CCR & ADC_CCR_CKMODE) != 0UL) \
:((((ADC3_COMMON)->CCR) & ADC_CCR_CKMODE) != 0UL))
/**
* @brief Simultaneously clear and set specific bits of the handle State.
* @note ADC_STATE_CLR_SET() macro is merely aliased to generic macro MODIFY_REG(),
* the first parameter is the ADC handle State, the second parameter is the
* bit field to clear, the third and last parameter is the bit field to set.
* @retval None
*/
#define ADC_STATE_CLR_SET MODIFY_REG
/**
* @brief Verify that a given value is aligned with the ADC resolution range.
* @param __RESOLUTION__ ADC resolution (16, 14, 12, 10 or 8 bits).
* @param __ADC_VALUE__ value checked against the resolution.
* @retval SET (__ADC_VALUE__ in line with __RESOLUTION__) or RESET (__ADC_VALUE__ not in line with __RESOLUTION__)
*/
#define IS_ADC_RANGE(__RESOLUTION__, __ADC_VALUE__) \
((__ADC_VALUE__) <= __LL_ADC_DIGITAL_SCALE(__RESOLUTION__))
/**
* @brief Verify the length of the scheduled regular conversions group.
* @param __LENGTH__ number of programmed conversions.
* @retval SET (__LENGTH__ is within the maximum number of possible programmable regular conversions) or RESET (__LENGTH__ is null or too large)
*/
#define IS_ADC_REGULAR_NB_CONV(__LENGTH__) (((__LENGTH__) >= (1UL)) && ((__LENGTH__) <= (16UL)))
/**
* @brief Verify the number of scheduled regular conversions in discontinuous mode.
* @param NUMBER number of scheduled regular conversions in discontinuous mode.
* @retval SET (NUMBER is within the maximum number of regular conversions in discontinuous mode) or RESET (NUMBER is null or too large)
*/
#define IS_ADC_REGULAR_DISCONT_NUMBER(NUMBER) (((NUMBER) >= (1UL)) && ((NUMBER) <= (8UL)))
/**
* @brief Verify the ADC clock setting.
* @param __ADC_CLOCK__ programmed ADC clock.
* @retval SET (__ADC_CLOCK__ is a valid value) or RESET (__ADC_CLOCK__ is invalid)
*/
#define IS_ADC_CLOCKPRESCALER(__ADC_CLOCK__) (((__ADC_CLOCK__) == ADC_CLOCK_SYNC_PCLK_DIV1) || \
((__ADC_CLOCK__) == ADC_CLOCK_SYNC_PCLK_DIV2) || \
((__ADC_CLOCK__) == ADC_CLOCK_SYNC_PCLK_DIV4) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV1) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV2) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV4) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV6) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV8) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV10) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV12) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV16) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV32) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV64) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV128) || \
((__ADC_CLOCK__) == ADC_CLOCK_ASYNC_DIV256) )
/**
* @brief Verify the ADC resolution setting.
* @param __RESOLUTION__ programmed ADC resolution.
* @retval SET (__RESOLUTION__ is a valid value) or RESET (__RESOLUTION__ is invalid)
*/
#define IS_ADC_RESOLUTION(__RESOLUTION__) (((__RESOLUTION__) == ADC_RESOLUTION_16B) || \
((__RESOLUTION__) == ADC_RESOLUTION_14B) || \
((__RESOLUTION__) == ADC_RESOLUTION_12B) || \
((__RESOLUTION__) == ADC_RESOLUTION_10B) || \
((__RESOLUTION__) == ADC_RESOLUTION_8B) )
/**
* @brief Verify the ADC resolution setting when limited to 8 bits.
* @param __RESOLUTION__ programmed ADC resolution when limited to 8 bits.
* @retval SET (__RESOLUTION__ is a valid value) or RESET (__RESOLUTION__ is invalid)
*/
#define IS_ADC_RESOLUTION_8_BITS(__RESOLUTION__) (((__RESOLUTION__) == ADC_RESOLUTION_8B))
/**
* @brief Verify the ADC scan mode.
* @param __SCAN_MODE__ programmed ADC scan mode.
* @retval SET (__SCAN_MODE__ is valid) or RESET (__SCAN_MODE__ is invalid)
*/
#define IS_ADC_SCAN_MODE(__SCAN_MODE__) (((__SCAN_MODE__) == ADC_SCAN_DISABLE) || \
((__SCAN_MODE__) == ADC_SCAN_ENABLE) )
/**
* @brief Verify the ADC edge trigger setting for regular group.
* @param __EDGE__ programmed ADC edge trigger setting.
* @retval SET (__EDGE__ is a valid value) or RESET (__EDGE__ is invalid)
*/
#define IS_ADC_EXTTRIG_EDGE(__EDGE__) (((__EDGE__) == ADC_EXTERNALTRIGCONVEDGE_NONE) || \
((__EDGE__) == ADC_EXTERNALTRIGCONVEDGE_RISING) || \
((__EDGE__) == ADC_EXTERNALTRIGCONVEDGE_FALLING) || \
((__EDGE__) == ADC_EXTERNALTRIGCONVEDGE_RISINGFALLING) )
/**
* @brief Verify the ADC regular conversions external trigger.
* @param __REGTRIG__ programmed ADC regular conversions external trigger.
* @retval SET (__REGTRIG__ is a valid value) or RESET (__REGTRIG__ is invalid)
*/
#define IS_ADC_EXTTRIG(__REGTRIG__) (((__REGTRIG__) == ADC_EXTERNALTRIG_T1_CC1) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T1_CC2) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T1_CC3) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T2_CC2) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T3_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T4_CC4) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_EXT_IT11) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T8_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T8_TRGO2) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T1_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T1_TRGO2) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T2_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T4_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T6_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T15_TRGO) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_T3_CC4) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_HR1_ADCTRG1) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_HR1_ADCTRG3) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_LPTIM1_OUT) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_LPTIM2_OUT) || \
((__REGTRIG__) == ADC_EXTERNALTRIG_LPTIM3_OUT) || \
((__REGTRIG__) == ADC_SOFTWARE_START) )
/**
* @brief Verify the ADC regular conversions check for converted data availability.
* @param __EOC_SELECTION__ converted data availability check.
* @retval SET (__EOC_SELECTION__ is a valid value) or RESET (__EOC_SELECTION__ is invalid)
*/
#define IS_ADC_EOC_SELECTION(__EOC_SELECTION__) (((__EOC_SELECTION__) == ADC_EOC_SINGLE_CONV) || \
((__EOC_SELECTION__) == ADC_EOC_SEQ_CONV) )
/**
* @brief Verify the ADC regular conversions overrun handling.
* @param __OVR__ ADC regular conversions overrun handling.
* @retval SET (__OVR__ is a valid value) or RESET (__OVR__ is invalid)
*/
#define IS_ADC_OVERRUN(__OVR__) (((__OVR__) == ADC_OVR_DATA_PRESERVED) || \
((__OVR__) == ADC_OVR_DATA_OVERWRITTEN) )
/**
* @brief Verify the ADC conversions sampling time.
* @param __TIME__ ADC conversions sampling time.
* @retval SET (__TIME__ is a valid value) or RESET (__TIME__ is invalid)
*/
#define IS_ADC_SAMPLE_TIME(__TIME__) (((__TIME__) == ADC_SAMPLETIME_1CYCLE_5) || \
((__TIME__) == ADC_SAMPLETIME_2CYCLES_5) || \
((__TIME__) == ADC_SAMPLETIME_8CYCLES_5) || \
((__TIME__) == ADC_SAMPLETIME_16CYCLES_5) || \
((__TIME__) == ADC_SAMPLETIME_32CYCLES_5) || \
((__TIME__) == ADC_SAMPLETIME_64CYCLES_5) || \
((__TIME__) == ADC_SAMPLETIME_387CYCLES_5) || \
((__TIME__) == ADC_SAMPLETIME_810CYCLES_5) )
/**
* @brief Verify the ADC regular channel setting.
* @param __CHANNEL__ programmed ADC regular channel.
* @retval SET (__CHANNEL__ is valid) or RESET (__CHANNEL__ is invalid)
*/
#define IS_ADC_REGULAR_RANK(__CHANNEL__) (((__CHANNEL__) == ADC_REGULAR_RANK_1 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_2 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_3 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_4 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_5 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_6 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_7 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_8 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_9 ) || \
((__CHANNEL__) == ADC_REGULAR_RANK_10) || \
((__CHANNEL__) == ADC_REGULAR_RANK_11) || \
((__CHANNEL__) == ADC_REGULAR_RANK_12) || \
((__CHANNEL__) == ADC_REGULAR_RANK_13) || \
((__CHANNEL__) == ADC_REGULAR_RANK_14) || \
((__CHANNEL__) == ADC_REGULAR_RANK_15) || \
((__CHANNEL__) == ADC_REGULAR_RANK_16) )
/**
* @}
*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup ADC_Private_Constants ADC Private Constants
* @{
*/
/* Fixed timeout values for ADC conversion (including sampling time) */
/* Maximum sampling time is 810.5 ADC clock cycle */
/* Maximum conversion time is 16.5 + Maximum sampling time */
/* or 16.5 + 810.5 = 827 ADC clock cycles */
/* Minimum ADC Clock frequency is 0.35 MHz */
/* Maximum conversion time is */
/* 827 / 0.35 MHz = 2.36 ms */
#define ADC_STOP_CONVERSION_TIMEOUT ( 5UL) /*!< ADC stop time-out value */
/* Delay for temperature sensor stabilization time. */
/* Maximum delay is 120us (refer device datasheet, parameter tSTART). */
/* Unit: us */
#define ADC_TEMPSENSOR_DELAY_US (LL_ADC_DELAY_TEMPSENSOR_STAB_US)
/* Delay for ADC voltage regulator startup time */
/* Maximum delay is 10 microseconds */
/* (refer device RM, parameter Tadcvreg_stup). */
#define ADC_STAB_DELAY_US ((uint32_t) 10) /*!< ADC voltage regulator startup time */
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup ADC_Exported_Macros ADC Exported Macros
* @{
*/
/* Macro for internal HAL driver usage, and possibly can be used into code of */
/* final user. */
/** @defgroup ADC_HAL_EM_HANDLE_IT_FLAG HAL ADC macro to manage HAL ADC handle, IT and flags.
* @{
*/
/** @brief Reset ADC handle state.
* @param __HANDLE__ ADC handle
* @retval None
*/
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
#define __HAL_ADC_RESET_HANDLE_STATE(__HANDLE__) \
do{ \
(__HANDLE__)->State = HAL_ADC_STATE_RESET; \
(__HANDLE__)->MspInitCallback = NULL; \
(__HANDLE__)->MspDeInitCallback = NULL; \
} while(0)
#else
#define __HAL_ADC_RESET_HANDLE_STATE(__HANDLE__) \
((__HANDLE__)->State = HAL_ADC_STATE_RESET)
#endif
/**
* @brief Enable ADC interrupt.
* @param __HANDLE__ ADC handle
* @param __INTERRUPT__ ADC Interrupt
* This parameter can be one of the following values:
* @arg @ref ADC_IT_RDY ADC Ready interrupt source
* @arg @ref ADC_IT_EOSMP ADC End of Sampling interrupt source
* @arg @ref ADC_IT_EOC ADC End of Regular Conversion interrupt source
* @arg @ref ADC_IT_EOS ADC End of Regular sequence of Conversions interrupt source
* @arg @ref ADC_IT_OVR ADC overrun interrupt source
* @arg @ref ADC_IT_JEOC ADC End of Injected Conversion interrupt source
* @arg @ref ADC_IT_JEOS ADC End of Injected sequence of Conversions interrupt source
* @arg @ref ADC_IT_AWD1 ADC Analog watchdog 1 interrupt source (main analog watchdog)
* @arg @ref ADC_IT_AWD2 ADC Analog watchdog 2 interrupt source (additional analog watchdog)
* @arg @ref ADC_IT_AWD3 ADC Analog watchdog 3 interrupt source (additional analog watchdog)
* @arg @ref ADC_IT_JQOVF ADC Injected Context Queue Overflow interrupt source.
* @retval None
*/
#define __HAL_ADC_ENABLE_IT(__HANDLE__, __INTERRUPT__) \
(((__HANDLE__)->Instance->IER) |= (__INTERRUPT__))
/**
* @brief Disable ADC interrupt.
* @param __HANDLE__ ADC handle
* @param __INTERRUPT__ ADC Interrupt
* This parameter can be one of the following values:
* @arg @ref ADC_IT_RDY ADC Ready interrupt source
* @arg @ref ADC_IT_EOSMP ADC End of Sampling interrupt source
* @arg @ref ADC_IT_EOC ADC End of Regular Conversion interrupt source
* @arg @ref ADC_IT_EOS ADC End of Regular sequence of Conversions interrupt source
* @arg @ref ADC_IT_OVR ADC overrun interrupt source
* @arg @ref ADC_IT_JEOC ADC End of Injected Conversion interrupt source
* @arg @ref ADC_IT_JEOS ADC End of Injected sequence of Conversions interrupt source
* @arg @ref ADC_IT_AWD1 ADC Analog watchdog 1 interrupt source (main analog watchdog)
* @arg @ref ADC_IT_AWD2 ADC Analog watchdog 2 interrupt source (additional analog watchdog)
* @arg @ref ADC_IT_AWD3 ADC Analog watchdog 3 interrupt source (additional analog watchdog)
* @arg @ref ADC_IT_JQOVF ADC Injected Context Queue Overflow interrupt source.
* @retval None
*/
#define __HAL_ADC_DISABLE_IT(__HANDLE__, __INTERRUPT__) \
(((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__))
/** @brief Checks if the specified ADC interrupt source is enabled or disabled.
* @param __HANDLE__ ADC handle
* @param __INTERRUPT__ ADC interrupt source to check
* This parameter can be one of the following values:
* @arg @ref ADC_IT_RDY ADC Ready interrupt source
* @arg @ref ADC_IT_EOSMP ADC End of Sampling interrupt source
* @arg @ref ADC_IT_EOC ADC End of Regular Conversion interrupt source
* @arg @ref ADC_IT_EOS ADC End of Regular sequence of Conversions interrupt source
* @arg @ref ADC_IT_OVR ADC overrun interrupt source
* @arg @ref ADC_IT_JEOC ADC End of Injected Conversion interrupt source
* @arg @ref ADC_IT_JEOS ADC End of Injected sequence of Conversions interrupt source
* @arg @ref ADC_IT_AWD1 ADC Analog watchdog 1 interrupt source (main analog watchdog)
* @arg @ref ADC_IT_AWD2 ADC Analog watchdog 2 interrupt source (additional analog watchdog)
* @arg @ref ADC_IT_AWD3 ADC Analog watchdog 3 interrupt source (additional analog watchdog)
* @arg @ref ADC_IT_JQOVF ADC Injected Context Queue Overflow interrupt source.
* @retval State of interruption (SET or RESET)
*/
#define __HAL_ADC_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) \
(((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__))
/**
* @brief Check whether the specified ADC flag is set or not.
* @param __HANDLE__ ADC handle
* @param __FLAG__ ADC flag
* This parameter can be one of the following values:
* @arg @ref ADC_FLAG_RDY ADC Ready flag
* @arg @ref ADC_FLAG_EOSMP ADC End of Sampling flag
* @arg @ref ADC_FLAG_EOC ADC End of Regular Conversion flag
* @arg @ref ADC_FLAG_EOS ADC End of Regular sequence of Conversions flag
* @arg @ref ADC_FLAG_OVR ADC overrun flag
* @arg @ref ADC_FLAG_JEOC ADC End of Injected Conversion flag
* @arg @ref ADC_FLAG_JEOS ADC End of Injected sequence of Conversions flag
* @arg @ref ADC_FLAG_AWD1 ADC Analog watchdog 1 flag (main analog watchdog)
* @arg @ref ADC_FLAG_AWD2 ADC Analog watchdog 2 flag (additional analog watchdog)
* @arg @ref ADC_FLAG_AWD3 ADC Analog watchdog 3 flag (additional analog watchdog)
* @arg @ref ADC_FLAG_JQOVF ADC Injected Context Queue Overflow flag.
* @retval State of flag (TRUE or FALSE).
*/
#define __HAL_ADC_GET_FLAG(__HANDLE__, __FLAG__) \
((((__HANDLE__)->Instance->ISR) & (__FLAG__)) == (__FLAG__))
/**
* @brief Clear the specified ADC flag.
* @param __HANDLE__ ADC handle
* @param __FLAG__ ADC flag
* This parameter can be one of the following values:
* @arg @ref ADC_FLAG_RDY ADC Ready flag
* @arg @ref ADC_FLAG_EOSMP ADC End of Sampling flag
* @arg @ref ADC_FLAG_EOC ADC End of Regular Conversion flag
* @arg @ref ADC_FLAG_EOS ADC End of Regular sequence of Conversions flag
* @arg @ref ADC_FLAG_OVR ADC overrun flag
* @arg @ref ADC_FLAG_JEOC ADC End of Injected Conversion flag
* @arg @ref ADC_FLAG_JEOS ADC End of Injected sequence of Conversions flag
* @arg @ref ADC_FLAG_AWD1 ADC Analog watchdog 1 flag (main analog watchdog)
* @arg @ref ADC_FLAG_AWD2 ADC Analog watchdog 2 flag (additional analog watchdog)
* @arg @ref ADC_FLAG_AWD3 ADC Analog watchdog 3 flag (additional analog watchdog)
* @arg @ref ADC_FLAG_JQOVF ADC Injected Context Queue Overflow flag.
* @retval None
*/
/* Note: bit cleared bit by writing 1 (writing 0 has no effect on any bit of register ISR) */
#define __HAL_ADC_CLEAR_FLAG(__HANDLE__, __FLAG__) \
(((__HANDLE__)->Instance->ISR) = (__FLAG__))
/**
* @}
*/
/** @defgroup ADC_HAL_EM_HELPER_MACRO HAL ADC helper macro
* @{
*/
/**
* @brief Helper macro to get ADC channel number in decimal format
* from literals ADC_CHANNEL_x.
* @note Example:
* __HAL_ADC_CHANNEL_TO_DECIMAL_NB(ADC_CHANNEL_4)
* will return decimal number "4".
* @note The input can be a value from functions where a channel
* number is returned, either defined with number
* or with bitfield (only one bit must be set).
* @param __CHANNEL__ This parameter can be one of the following values:
* @arg @ref ADC_CHANNEL_0 (3)
* @arg @ref ADC_CHANNEL_1 (3)
* @arg @ref ADC_CHANNEL_2 (3)
* @arg @ref ADC_CHANNEL_3 (3)
* @arg @ref ADC_CHANNEL_4 (3)
* @arg @ref ADC_CHANNEL_5 (3)
* @arg @ref ADC_CHANNEL_6
* @arg @ref ADC_CHANNEL_7
* @arg @ref ADC_CHANNEL_8
* @arg @ref ADC_CHANNEL_9
* @arg @ref ADC_CHANNEL_10
* @arg @ref ADC_CHANNEL_11
* @arg @ref ADC_CHANNEL_12
* @arg @ref ADC_CHANNEL_13
* @arg @ref ADC_CHANNEL_14
* @arg @ref ADC_CHANNEL_15
* @arg @ref ADC_CHANNEL_16
* @arg @ref ADC_CHANNEL_17
* @arg @ref ADC_CHANNEL_18
* @arg @ref ADC_CHANNEL_VREFINT (1)
* @arg @ref ADC_CHANNEL_TEMPSENSOR (1)
* @arg @ref ADC_CHANNEL_VBAT (1)
* @arg @ref ADC_CHANNEL_DAC1CH1_ADC2 (2)
* @arg @ref ADC_CHANNEL_DAC1CH2_ADC2 (2)
*
* (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
* (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to 8 Ms/s)).
* Other channels are slow channels (conversion rate: refer to reference manual).
* @retval Value between Min_Data=0 and Max_Data=18
*/
#define __HAL_ADC_CHANNEL_TO_DECIMAL_NB(__CHANNEL__) \
__LL_ADC_CHANNEL_TO_DECIMAL_NB((__CHANNEL__))
/**
* @brief Helper macro to get ADC channel in literal format ADC_CHANNEL_x
* from number in decimal format.
* @note Example:
* __HAL_ADC_DECIMAL_NB_TO_CHANNEL(4)
* will return a data equivalent to "ADC_CHANNEL_4".
* @param __DECIMAL_NB__ Value between Min_Data=0 and Max_Data=18
* @retval Returned value can be one of the following values:
* @arg @ref ADC_CHANNEL_0 (3)
* @arg @ref ADC_CHANNEL_1 (3)
* @arg @ref ADC_CHANNEL_2 (3)
* @arg @ref ADC_CHANNEL_3 (3)
* @arg @ref ADC_CHANNEL_4 (3)
* @arg @ref ADC_CHANNEL_5 (3)
* @arg @ref ADC_CHANNEL_6
* @arg @ref ADC_CHANNEL_7
* @arg @ref ADC_CHANNEL_8
* @arg @ref ADC_CHANNEL_9
* @arg @ref ADC_CHANNEL_10
* @arg @ref ADC_CHANNEL_11
* @arg @ref ADC_CHANNEL_12
* @arg @ref ADC_CHANNEL_13
* @arg @ref ADC_CHANNEL_14
* @arg @ref ADC_CHANNEL_15
* @arg @ref ADC_CHANNEL_16
* @arg @ref ADC_CHANNEL_17
* @arg @ref ADC_CHANNEL_18
* @arg @ref ADC_CHANNEL_VREFINT (1)
* @arg @ref ADC_CHANNEL_TEMPSENSOR (1)
* @arg @ref ADC_CHANNEL_VBAT (1)
* @arg @ref ADC_CHANNEL_DAC1CH1_ADC2 (2)
* @arg @ref ADC_CHANNEL_DAC1CH2_ADC2 (2)
*
* (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
* (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to 8 Ms/s)).
* Other channels are slow channels (conversion rate: refer to reference manual).\n
* (1, 2) For ADC channel read back from ADC register,
* comparison with internal channel parameter to be done
* using helper macro @ref __LL_ADC_CHANNEL_INTERNAL_TO_EXTERNAL().
*/
#define __HAL_ADC_DECIMAL_NB_TO_CHANNEL(__DECIMAL_NB__) \
__LL_ADC_DECIMAL_NB_TO_CHANNEL((__DECIMAL_NB__))
/**
* @brief Helper macro to determine whether the selected channel
* corresponds to literal definitions of driver.
* @note The different literal definitions of ADC channels are:
* - ADC internal channel:
* ADC_CHANNEL_VREFINT, ADC_CHANNEL_TEMPSENSOR, ...
* - ADC external channel (channel connected to a GPIO pin):
* ADC_CHANNEL_1, ADC_CHANNEL_2, ...
* @note The channel parameter must be a value defined from literal
* definition of a ADC internal channel (ADC_CHANNEL_VREFINT,
* ADC_CHANNEL_TEMPSENSOR, ...),
* ADC external channel (ADC_CHANNEL_1, ADC_CHANNEL_2, ...),
* must not be a value from functions where a channel number is
* returned from ADC registers,
* because internal and external channels share the same channel
* number in ADC registers. The differentiation is made only with
* parameters definitions of driver.
* @param __CHANNEL__ This parameter can be one of the following values:
* @arg @ref ADC_CHANNEL_0 (3)
* @arg @ref ADC_CHANNEL_1 (3)
* @arg @ref ADC_CHANNEL_2 (3)
* @arg @ref ADC_CHANNEL_3 (3)
* @arg @ref ADC_CHANNEL_4 (3)
* @arg @ref ADC_CHANNEL_5 (3)
* @arg @ref ADC_CHANNEL_6
* @arg @ref ADC_CHANNEL_7
* @arg @ref ADC_CHANNEL_8
* @arg @ref ADC_CHANNEL_9
* @arg @ref ADC_CHANNEL_10
* @arg @ref ADC_CHANNEL_11
* @arg @ref ADC_CHANNEL_12
* @arg @ref ADC_CHANNEL_13
* @arg @ref ADC_CHANNEL_14
* @arg @ref ADC_CHANNEL_15
* @arg @ref ADC_CHANNEL_16
* @arg @ref ADC_CHANNEL_17
* @arg @ref ADC_CHANNEL_18
* @arg @ref ADC_CHANNEL_VREFINT (1)
* @arg @ref ADC_CHANNEL_TEMPSENSOR (1)
* @arg @ref ADC_CHANNEL_VBAT (1)
* @arg @ref ADC_CHANNEL_DAC1CH1_ADC2 (2)
* @arg @ref ADC_CHANNEL_DAC1CH2_ADC2 (2)
*
* (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
* (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to 8 Ms/s)).
* Other channels are slow channels (conversion rate: refer to reference manual).
* @retval Value "0" if the channel corresponds to a parameter definition of a ADC external channel (channel connected to a GPIO pin).
* Value "1" if the channel corresponds to a parameter definition of a ADC internal channel.
*/
#define __HAL_ADC_IS_CHANNEL_INTERNAL(__CHANNEL__) \
__LL_ADC_IS_CHANNEL_INTERNAL((__CHANNEL__))
/**
* @brief Helper macro to convert a channel defined from parameter
* definition of a ADC internal channel (ADC_CHANNEL_VREFINT,
* ADC_CHANNEL_TEMPSENSOR, ...),
* to its equivalent parameter definition of a ADC external channel
* (ADC_CHANNEL_1, ADC_CHANNEL_2, ...).
* @note The channel parameter can be, additionally to a value
* defined from parameter definition of a ADC internal channel
* (ADC_CHANNEL_VREFINT, ADC_CHANNEL_TEMPSENSOR, ...),
* a value defined from parameter definition of
* ADC external channel (ADC_CHANNEL_1, ADC_CHANNEL_2, ...)
* or a value from functions where a channel number is returned
* from ADC registers.
* @param __CHANNEL__ This parameter can be one of the following values:
* @arg @ref ADC_CHANNEL_0 (3)
* @arg @ref ADC_CHANNEL_1 (3)
* @arg @ref ADC_CHANNEL_2 (3)
* @arg @ref ADC_CHANNEL_3 (3)
* @arg @ref ADC_CHANNEL_4 (3)
* @arg @ref ADC_CHANNEL_5 (3)
* @arg @ref ADC_CHANNEL_6
* @arg @ref ADC_CHANNEL_7
* @arg @ref ADC_CHANNEL_8
* @arg @ref ADC_CHANNEL_9
* @arg @ref ADC_CHANNEL_10
* @arg @ref ADC_CHANNEL_11
* @arg @ref ADC_CHANNEL_12
* @arg @ref ADC_CHANNEL_13
* @arg @ref ADC_CHANNEL_14
* @arg @ref ADC_CHANNEL_15
* @arg @ref ADC_CHANNEL_16
* @arg @ref ADC_CHANNEL_17
* @arg @ref ADC_CHANNEL_18
* @arg @ref ADC_CHANNEL_VREFINT (1)
* @arg @ref ADC_CHANNEL_TEMPSENSOR (1)
* @arg @ref ADC_CHANNEL_VBAT (1)
* @arg @ref ADC_CHANNEL_DAC1CH1_ADC2 (2)
* @arg @ref ADC_CHANNEL_DAC1CH2_ADC2 (2)
*
* (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
* (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to 8 Ms/s)).
* Other channels are slow channels (conversion rate: refer to reference manual).
* @retval Returned value can be one of the following values:
* @arg @ref ADC_CHANNEL_0
* @arg @ref ADC_CHANNEL_1
* @arg @ref ADC_CHANNEL_2
* @arg @ref ADC_CHANNEL_3
* @arg @ref ADC_CHANNEL_4
* @arg @ref ADC_CHANNEL_5
* @arg @ref ADC_CHANNEL_6
* @arg @ref ADC_CHANNEL_7
* @arg @ref ADC_CHANNEL_8
* @arg @ref ADC_CHANNEL_9
* @arg @ref ADC_CHANNEL_10
* @arg @ref ADC_CHANNEL_11
* @arg @ref ADC_CHANNEL_12
* @arg @ref ADC_CHANNEL_13
* @arg @ref ADC_CHANNEL_14
* @arg @ref ADC_CHANNEL_15
* @arg @ref ADC_CHANNEL_16
* @arg @ref ADC_CHANNEL_17
* @arg @ref ADC_CHANNEL_18
*/
#define __HAL_ADC_CHANNEL_INTERNAL_TO_EXTERNAL(__CHANNEL__) \
__LL_ADC_CHANNEL_INTERNAL_TO_EXTERNAL((__CHANNEL__))
/**
* @brief Helper macro to determine whether the internal channel
* selected is available on the ADC instance selected.
* @note The channel parameter must be a value defined from parameter
* definition of a ADC internal channel (ADC_CHANNEL_VREFINT,
* ADC_CHANNEL_TEMPSENSOR, ...),
* must not be a value defined from parameter definition of
* ADC external channel (ADC_CHANNEL_1, ADC_CHANNEL_2, ...)
* or a value from functions where a channel number is
* returned from ADC registers,
* because internal and external channels share the same channel
* number in ADC registers. The differentiation is made only with
* parameters definitions of driver.
* @param __ADC_INSTANCE__ ADC instance
* @param __CHANNEL__ This parameter can be one of the following values:
* @arg @ref ADC_CHANNEL_VREFINT (1)
* @arg @ref ADC_CHANNEL_TEMPSENSOR (1)
* @arg @ref ADC_CHANNEL_VBAT (1)
* @arg @ref ADC_CHANNEL_DAC1CH1_ADC2 (2)
* @arg @ref ADC_CHANNEL_DAC1CH2_ADC2 (2)
*
* (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
* (2) On STM32H7, parameter available only on ADC instance: ADC2.
* @retval Value "0" if the internal channel selected is not available on the ADC instance selected.
* Value "1" if the internal channel selected is available on the ADC instance selected.
*/
#define __HAL_ADC_IS_CHANNEL_INTERNAL_AVAILABLE(__ADC_INSTANCE__, __CHANNEL__) \
__LL_ADC_IS_CHANNEL_INTERNAL_AVAILABLE((__ADC_INSTANCE__), (__CHANNEL__))
/**
* @brief Helper macro to get the ADC multimode conversion data of ADC master
* or ADC slave from raw value with both ADC conversion data concatenated.
* @note This macro is intended to be used when multimode transfer by DMA
* is enabled: refer to function @ref LL_ADC_SetMultiDMATransfer().
* In this case the transferred data need to processed with this macro
* to separate the conversion data of ADC master and ADC slave.
* @param __ADC_MULTI_MASTER_SLAVE__ This parameter can be one of the following values:
* @arg @ref LL_ADC_MULTI_MASTER
* @arg @ref LL_ADC_MULTI_SLAVE
* @param __ADC_MULTI_CONV_DATA__ Value between Min_Data=0x000 and Max_Data=0xFFF
* @retval Value between Min_Data=0x000 and Max_Data=0xFFF
*/
#define __HAL_ADC_MULTI_CONV_DATA_MASTER_SLAVE(__ADC_MULTI_MASTER_SLAVE__, __ADC_MULTI_CONV_DATA__) \
__LL_ADC_MULTI_CONV_DATA_MASTER_SLAVE((__ADC_MULTI_MASTER_SLAVE__), (__ADC_MULTI_CONV_DATA__))
/**
* @brief Helper macro to select the ADC common instance
* to which is belonging the selected ADC instance.
* @note ADC common register instance can be used for:
* - Set parameters common to several ADC instances
* - Multimode (for devices with several ADC instances)
* Refer to functions having argument "ADCxy_COMMON" as parameter.
* @param __ADCx__ ADC instance
* @retval ADC common register instance
*/
#define __HAL_ADC_COMMON_INSTANCE(__ADCx__) \
__LL_ADC_COMMON_INSTANCE((__ADCx__))
/**
* @brief Helper macro to check if all ADC instances sharing the same
* ADC common instance are disabled.
* @note This check is required by functions with setting conditioned to
* ADC state:
* All ADC instances of the ADC common group must be disabled.
* Refer to functions having argument "ADCxy_COMMON" as parameter.
* @note On devices with only 1 ADC common instance, parameter of this macro
* is useless and can be ignored (parameter kept for compatibility
* with devices featuring several ADC common instances).
* @param __ADCXY_COMMON__ ADC common instance
* (can be set directly from CMSIS definition or by using helper macro @ref __LL_ADC_COMMON_INSTANCE() )
* @retval Value "0" if all ADC instances sharing the same ADC common instance
* are disabled.
* Value "1" if at least one ADC instance sharing the same ADC common instance
* is enabled.
*/
#define __HAL_ADC_IS_ENABLED_ALL_COMMON_INSTANCE(__ADCXY_COMMON__) \
__LL_ADC_IS_ENABLED_ALL_COMMON_INSTANCE((__ADCXY_COMMON__))
/**
* @brief Helper macro to define the ADC conversion data full-scale digital
* value corresponding to the selected ADC resolution.
* @note ADC conversion data full-scale corresponds to voltage range
* determined by analog voltage references Vref+ and Vref-
* (refer to reference manual).
* @param __ADC_RESOLUTION__ This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @retval ADC conversion data full-scale digital value
*/
#define __HAL_ADC_DIGITAL_SCALE(__ADC_RESOLUTION__) \
__LL_ADC_DIGITAL_SCALE((__ADC_RESOLUTION__))
/**
* @brief Helper macro to convert the ADC conversion data from
* a resolution to another resolution.
* @param __DATA__ ADC conversion data to be converted
* @param __ADC_RESOLUTION_CURRENT__ Resolution of to the data to be converted
* This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @param __ADC_RESOLUTION_TARGET__ Resolution of the data after conversion
* This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @retval ADC conversion data to the requested resolution
*/
#define __HAL_ADC_CONVERT_DATA_RESOLUTION(__DATA__,\
__ADC_RESOLUTION_CURRENT__,\
__ADC_RESOLUTION_TARGET__) \
__LL_ADC_CONVERT_DATA_RESOLUTION((__DATA__), \
(__ADC_RESOLUTION_CURRENT__), \
(__ADC_RESOLUTION_TARGET__))
/**
* @brief Helper macro to calculate the voltage (unit: mVolt)
* corresponding to a ADC conversion data (unit: digital value).
* @note Analog reference voltage (Vref+) must be either known from
* user board environment or can be calculated using ADC measurement
* and ADC helper macro @ref __LL_ADC_CALC_VREFANALOG_VOLTAGE().
* @param __VREFANALOG_VOLTAGE__ Analog reference voltage (unit: mV)
* @param __ADC_DATA__ ADC conversion data (resolution 12 bits)
* (unit: digital value).
* @param __ADC_RESOLUTION__ This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @retval ADC conversion data equivalent voltage value (unit: mVolt)
*/
#define __HAL_ADC_CALC_DATA_TO_VOLTAGE(__VREFANALOG_VOLTAGE__,\
__ADC_DATA__,\
__ADC_RESOLUTION__) \
__LL_ADC_CALC_DATA_TO_VOLTAGE((__VREFANALOG_VOLTAGE__), \
(__ADC_DATA__), \
(__ADC_RESOLUTION__))
/**
* @brief Helper macro to calculate analog reference voltage (Vref+)
* (unit: mVolt) from ADC conversion data of internal voltage
* reference VrefInt.
* @note Computation is using VrefInt calibration value
* stored in system memory for each device during production.
* @note This voltage depends on user board environment: voltage level
* connected to pin Vref+.
* On devices with small package, the pin Vref+ is not present
* and internally bonded to pin Vdda.
* @note On this STM32 serie, calibration data of internal voltage reference
* VrefInt corresponds to a resolution of 12 bits,
* this is the recommended ADC resolution to convert voltage of
* internal voltage reference VrefInt.
* Otherwise, this macro performs the processing to scale
* ADC conversion data to 12 bits.
* @param __VREFINT_ADC_DATA__ ADC conversion data (resolution 12 bits)
* of internal voltage reference VrefInt (unit: digital value).
* @param __ADC_RESOLUTION__ This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @retval Analog reference voltage (unit: mV)
*/
#define __HAL_ADC_CALC_VREFANALOG_VOLTAGE(__VREFINT_ADC_DATA__,\
__ADC_RESOLUTION__) \
__LL_ADC_CALC_VREFANALOG_VOLTAGE((__VREFINT_ADC_DATA__), \
(__ADC_RESOLUTION__))
/**
* @brief Helper macro to calculate the temperature (unit: degree Celsius)
* from ADC conversion data of internal temperature sensor.
* @note Computation is using temperature sensor calibration values
* stored in system memory for each device during production.
* @note Calculation formula:
* Temperature = ((TS_ADC_DATA - TS_CAL1)
* * (TS_CAL2_TEMP - TS_CAL1_TEMP))
* / (TS_CAL2 - TS_CAL1) + TS_CAL1_TEMP
* with TS_ADC_DATA = temperature sensor raw data measured by ADC
* Avg_Slope = (TS_CAL2 - TS_CAL1)
* / (TS_CAL2_TEMP - TS_CAL1_TEMP)
* TS_CAL1 = equivalent TS_ADC_DATA at temperature
* TEMP_DEGC_CAL1 (calibrated in factory)
* TS_CAL2 = equivalent TS_ADC_DATA at temperature
* TEMP_DEGC_CAL2 (calibrated in factory)
* Caution: Calculation relevancy under reserve that calibration
* parameters are correct (address and data).
* To calculate temperature using temperature sensor
* datasheet typical values (generic values less, therefore
* less accurate than calibrated values),
* use helper macro @ref __LL_ADC_CALC_TEMPERATURE_TYP_PARAMS().
* @note As calculation input, the analog reference voltage (Vref+) must be
* defined as it impacts the ADC LSB equivalent voltage.
* @note Analog reference voltage (Vref+) must be either known from
* user board environment or can be calculated using ADC measurement
* and ADC helper macro @ref __LL_ADC_CALC_VREFANALOG_VOLTAGE().
* @note On this STM32 serie, calibration data of temperature sensor
* corresponds to a resolution of 12 bits,
* this is the recommended ADC resolution to convert voltage of
* temperature sensor.
* Otherwise, this macro performs the processing to scale
* ADC conversion data to 12 bits.
* @param __VREFANALOG_VOLTAGE__ Analog reference voltage (unit: mV)
* @param __TEMPSENSOR_ADC_DATA__ ADC conversion data of internal
* temperature sensor (unit: digital value).
* @param __ADC_RESOLUTION__ ADC resolution at which internal temperature
* sensor voltage has been measured.
* This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @retval Temperature (unit: degree Celsius)
*/
#define __HAL_ADC_CALC_TEMPERATURE(__VREFANALOG_VOLTAGE__,\
__TEMPSENSOR_ADC_DATA__,\
__ADC_RESOLUTION__) \
__LL_ADC_CALC_TEMPERATURE((__VREFANALOG_VOLTAGE__), \
(__TEMPSENSOR_ADC_DATA__), \
(__ADC_RESOLUTION__))
/**
* @brief Helper macro to calculate the temperature (unit: degree Celsius)
* from ADC conversion data of internal temperature sensor.
* @note Computation is using temperature sensor typical values
* (refer to device datasheet).
* @note Calculation formula:
* Temperature = (TS_TYP_CALx_VOLT(uV) - TS_ADC_DATA * Conversion_uV)
* / Avg_Slope + CALx_TEMP
* with TS_ADC_DATA = temperature sensor raw data measured by ADC
* (unit: digital value)
* Avg_Slope = temperature sensor slope
* (unit: uV/Degree Celsius)
* TS_TYP_CALx_VOLT = temperature sensor digital value at
* temperature CALx_TEMP (unit: mV)
* Caution: Calculation relevancy under reserve the temperature sensor
* of the current device has characteristics in line with
* datasheet typical values.
* If temperature sensor calibration values are available on
* on this device (presence of macro __LL_ADC_CALC_TEMPERATURE()),
* temperature calculation will be more accurate using
* helper macro @ref __LL_ADC_CALC_TEMPERATURE().
* @note As calculation input, the analog reference voltage (Vref+) must be
* defined as it impacts the ADC LSB equivalent voltage.
* @note Analog reference voltage (Vref+) must be either known from
* user board environment or can be calculated using ADC measurement
* and ADC helper macro @ref __LL_ADC_CALC_VREFANALOG_VOLTAGE().
* @note ADC measurement data must correspond to a resolution of 12bits
* (full scale digital value 4095). If not the case, the data must be
* preliminarily rescaled to an equivalent resolution of 12 bits.
* @param __TEMPSENSOR_TYP_AVGSLOPE__ Device datasheet data: Temperature sensor slope typical value (unit: uV/DegCelsius).
* On STM32H7, refer to device datasheet parameter "Avg_Slope".
* @param __TEMPSENSOR_TYP_CALX_V__ Device datasheet data: Temperature sensor voltage typical value (at temperature and Vref+ defined in parameters below) (unit: mV).
* On STM32H7, refer to device datasheet parameter "V30" (corresponding to TS_CAL1).
* @param __TEMPSENSOR_CALX_TEMP__ Device datasheet data: Temperature at which temperature sensor voltage (see parameter above) is corresponding (unit: mV)
* @param __VREFANALOG_VOLTAGE__ Analog voltage reference (Vref+) voltage (unit: mV)
* @param __TEMPSENSOR_ADC_DATA__ ADC conversion data of internal temperature sensor (unit: digital value).
* @param __ADC_RESOLUTION__ ADC resolution at which internal temperature sensor voltage has been measured.
* This parameter can be one of the following values:
* @arg @ref ADC_RESOLUTION_16B
* @arg @ref ADC_RESOLUTION_14B
* @arg @ref ADC_RESOLUTION_12B
* @arg @ref ADC_RESOLUTION_10B
* @arg @ref ADC_RESOLUTION_8B
* @retval Temperature (unit: degree Celsius)
*/
#define __HAL_ADC_CALC_TEMPERATURE_TYP_PARAMS(__TEMPSENSOR_TYP_AVGSLOPE__,\
__TEMPSENSOR_TYP_CALX_V__,\
__TEMPSENSOR_CALX_TEMP__,\
__VREFANALOG_VOLTAGE__,\
__TEMPSENSOR_ADC_DATA__,\
__ADC_RESOLUTION__) \
__LL_ADC_CALC_TEMPERATURE_TYP_PARAMS((__TEMPSENSOR_TYP_AVGSLOPE__), \
(__TEMPSENSOR_TYP_CALX_V__), \
(__TEMPSENSOR_CALX_TEMP__), \
(__VREFANALOG_VOLTAGE__), \
(__TEMPSENSOR_ADC_DATA__), \
(__ADC_RESOLUTION__))
/**
* @}
*/
/**
* @}
*/
/* Include ADC HAL Extended module */
#include "stm32h7xx_hal_adc_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup ADC_Exported_Functions
* @{
*/
/** @addtogroup ADC_Exported_Functions_Group1
* @brief Initialization and Configuration functions
* @{
*/
/* Initialization and de-initialization functions ****************************/
HAL_StatusTypeDef HAL_ADC_Init(ADC_HandleTypeDef *hadc);
HAL_StatusTypeDef HAL_ADC_DeInit(ADC_HandleTypeDef *hadc);
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc);
void HAL_ADC_MspDeInit(ADC_HandleTypeDef *hadc);
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
/* Callbacks Register/UnRegister functions ***********************************/
HAL_StatusTypeDef HAL_ADC_RegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID,
pADC_CallbackTypeDef pCallback);
HAL_StatusTypeDef HAL_ADC_UnRegisterCallback(ADC_HandleTypeDef *hadc, HAL_ADC_CallbackIDTypeDef CallbackID);
#endif /* USE_HAL_ADC_REGISTER_CALLBACKS */
/**
* @}
*/
/** @addtogroup ADC_Exported_Functions_Group2
* @brief IO operation functions
* @{
*/
/* IO operation functions *****************************************************/
/* Blocking mode: Polling */
HAL_StatusTypeDef HAL_ADC_Start(ADC_HandleTypeDef *hadc);
HAL_StatusTypeDef HAL_ADC_Stop(ADC_HandleTypeDef *hadc);
HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef *hadc, uint32_t Timeout);
HAL_StatusTypeDef HAL_ADC_PollForEvent(ADC_HandleTypeDef *hadc, uint32_t EventType, uint32_t Timeout);
/* Non-blocking mode: Interruption */
HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef *hadc);
HAL_StatusTypeDef HAL_ADC_Stop_IT(ADC_HandleTypeDef *hadc);
/* Non-blocking mode: DMA */
HAL_StatusTypeDef HAL_ADC_Start_DMA(ADC_HandleTypeDef *hadc, uint32_t *pData, uint32_t Length);
HAL_StatusTypeDef HAL_ADC_Stop_DMA(ADC_HandleTypeDef *hadc);
/* ADC retrieve conversion value intended to be used with polling or interruption */
uint32_t HAL_ADC_GetValue(ADC_HandleTypeDef *hadc);
/* ADC IRQHandler and Callbacks used in non-blocking modes (Interruption and DMA) */
void HAL_ADC_IRQHandler(ADC_HandleTypeDef *hadc);
void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef *hadc);
void HAL_ADC_ConvHalfCpltCallback(ADC_HandleTypeDef *hadc);
void HAL_ADC_LevelOutOfWindowCallback(ADC_HandleTypeDef *hadc);
void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc);
/**
* @}
*/
/** @addtogroup ADC_Exported_Functions_Group3 Peripheral Control functions
* @brief Peripheral Control functions
* @{
*/
/* Peripheral Control functions ***********************************************/
HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef *hadc, ADC_ChannelConfTypeDef *sConfig);
HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef *hadc, ADC_AnalogWDGConfTypeDef *AnalogWDGConfig);
/**
* @}
*/
/* Peripheral State functions *************************************************/
/** @addtogroup ADC_Exported_Functions_Group4
* @{
*/
uint32_t HAL_ADC_GetState(ADC_HandleTypeDef *hadc);
uint32_t HAL_ADC_GetError(ADC_HandleTypeDef *hadc);
/**
* @}
*/
/**
* @}
*/
/* Private functions -----------------------------------------------------------*/
/** @addtogroup ADC_Private_Functions ADC Private Functions
* @{
*/
HAL_StatusTypeDef ADC_ConversionStop(ADC_HandleTypeDef *hadc, uint32_t ConversionGroup);
HAL_StatusTypeDef ADC_Enable(ADC_HandleTypeDef *hadc);
HAL_StatusTypeDef ADC_Disable(ADC_HandleTypeDef *hadc);
void ADC_DMAConvCplt(DMA_HandleTypeDef *hdma);
void ADC_DMAHalfConvCplt(DMA_HandleTypeDef *hdma);
void ADC_DMAError(DMA_HandleTypeDef *hdma);
void ADC_ConfigureBoostMode(ADC_HandleTypeDef* hadc);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32H7xx_HAL_ADC_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/